15波长输出的布里渊掺铒光纤激光器

多波长布里渊掺铒光纤激光器是一种新型的多波长光纤激光器,其原理是利用受激布里渊增益和掺铒光纤的线性增益,可以在常温下得到波长间隔约为0．08nm(～10GHz)的多波长输出。报道的布里渊掺铒光纤激光器,在布里渊抽运功率为1．7mW、980nm抽运功率为300mW的情况下得到稳定的15个波长(间隔～10GHz)的输出,这种激光器用作光传感器、光谱分析仪以及密集波分复用系统的光源。实验发现,输出波长的个数随着980nm抽运功率的增大而增加。另外,布里渊掺铒光纤激光器的信号功率主要来自于掺铒光纤的增益,而布里渊增益对它的影响不大。     

间隔0.173nm的可调谐多波长布里渊掺铒光纤激光器

使用四端口环行器和可调谐滤波器,设计了一种间隔为双倍布里渊频移的多波长布里渊掺铒光纤激光器.该光纤激光器中使用的四端口环形器可以限制奇次阶斯托克斯光在腔内循环并耦合输出初始泵浦光和偶次阶斯托克斯光,而可调滤波器抑制环形腔所形成的自激振荡模,增加了激发多波长激光的功率,从而增加多波长输出个数及其调谐范围.在布里渊泵浦功率为8dBm、980nm泵浦功率为279mW时,实验获得波长间隔为0.173nm的6个波长的激光输出,输出激光的可调谐范围为28nm.     

布里渊-掺铒光纤随机光纤激光器输出特性分析

设计了一种基于受激布里渊散射和掺铒光纤混合增益的随机光纤激光器,该激光器选用两段长为20km的单模光纤组成全开放腔结构,利用单模光纤的瑞利散射提供随机光反馈.研究表明,固定布里渊泵浦波长和泵浦功率分别为1 550.00nm和2.19mW时,增加掺铒光纤泵浦功率,可以实现两个波长的随机激光输出,一阶和二阶受激布里渊散射光与布里渊泵浦光波长间隔分别约为0.088nm和0.174nm,产生一阶和二阶受激布里渊散射对应的掺铒光纤泵浦功率分别为190mW和370mW;当掺铒光纤泵浦功率为433mW时,激光器两端的最大输出功率为1.60mW和1.68mW.当掺铒光纤泵浦功率明显高于阈值功率时,获得的一阶和二阶随机激光输出稳定,3dB线宽约为0.022nm,峰值强度和位置基本不随时间而变化.     

基于受激布里渊散射的波长间隔可变多波长光纤激光器

提出了一个基于自激发受激布里渊散射的波长间隔可变多波长光纤激光器.利用单模光纤中自激发产生的非线性布里渊增益和掺铒光纤的线性增益组成混合增益光纤激光器,从而使光纤激光器在室温下产生稳定的多波长输出.改变双折射光纤环镜滤波器中保偏光纤的长度,可以实现波长间隔可变多波长激光产生,提高了多波长光纤激光器操作的灵活性和实用性.实验实现了波长间隔从0.8 nm至0.076 nm可变的多波长激光产生,波长数随波长间隔减小而增加,间隔为0.08 nm的激光波长数达86.     

基于受激布里渊散射的波长间隔可变多波长光纤激光器

提出了一个基于自激发受激布里渊散射的波长间隔可变多波长光纤激光器.利用单模光纤中自激发产生的非线性布里渊增益和掺铒光纤的线性增益组成混合增益光纤激光器,从而使光纤激光器在室温下产生稳定的多波长输出.改变双折射光纤环镜滤波器中保偏光纤的长度,可以实现波长间隔可变多波长激光产生,提高了多波长光纤激光器操作的灵活性和实用性.实验实现了波长间隔从0.8nm至0.076nm可变的多波长激光产生,波长数随波长间隔减小而增加,间隔为0.08nm的激光波长数达86.     

一种新型自激发布里渊掺铒光纤激光器

利用级联的受激布里渊效应,自激发布里渊掺铒光纤激光器可以实现常温下的多波长激光输出。通过在自激发掺铒光纤激光器中引入一个高双折射萨尼亚克(Sagnac)环形滤波器,调节萨尼亚克环形滤波器的偏振控制器(PC),实现了可调谐多波长输出,同时在实验中观测到双布里渊多波长带的现象。研究了这种光纤激光器中萨尼亚克环形滤波器的带宽和980 nm抽运光功率对输出波长数的影响,在萨尼亚克环形滤波器的带宽为83.3 nm以及980 nm抽运光功率为260 mW时,得到了52个间隔为0.088 nm的多波长激光输出。     

基于两滤波器级联和饱和吸收体的单纵模双波长光纤激光器

提出和证实了一种光纤环形激光器. 将一个带通滤波器与一个带阻滤波器级联,用一段保偏掺铒光纤作为饱和吸收体,得到了一种单纵模双波长光纤激光器. 结果表明,该激光器波长间隔为0.4 nm,边模抑制比大于49 dB.如果将两个波长进行差拍,该激光器有潜力得到49.85 GHz的微波信号.     

宽波长范围窄线宽波长连续可调的光纤激光器

研制了一种宽波长范围窄线宽波长连续可调的光纤激光器,激光器基于环形腔结构,采用980nm的半导体激光器作为泵浦源,掺铒光纤作为增益介质,使用一段未泵浦的保偏掺铒光纤作为饱和吸收体压窄线宽。使用光纤法布里-珀罗滤波器作为选频器件,通过调节光纤其驱动电压实现光纤激光器的波长扫描。利用激光器的相干长度与干涉仪干涉条纹的关系动态测量激光器的光谱线宽,最终得到了扫描范围为1515.1～1588.6nm,线宽小于0.025nm的波长连续可调的光谱输出。     

双向反馈布里渊-喇曼光纤激光器输出特性

设计了一种双向反馈布里渊-喇曼光纤激光器,研究了布里渊泵浦对输出特性的影响.布里渊-喇曼光纤激光器由一段7km色散补偿光纤、1 455nm喇曼泵浦、可调谐激光器及双反馈环组成.喇曼泵浦功率固定在250mW,布里渊泵浦工作波段在喇曼峰值增益处附近,可得到较多波长数输出.随着布里渊泵浦功率增加,相邻的布里渊斯托克斯光和经背向瑞利散射的斯托克斯光之间功率差减小,同时各阶斯托克斯光平均强度增加并达到饱和.受色散补偿光纤中喇曼交叉增益影响,布里渊泵浦功率由1.8dBm增加到6.9dBm,输出多波长数先增后减.当布里渊泵浦功率为4.4dBm时,对应输出波长数最多,为37个,波长间隔0.078nm.     

基于高双折射Sagnac环的可调环形腔掺铒光纤激光器理论与实验研究

报道了一种利用偏振控制器（PC）和保偏光纤（PMF）组成的高双折射Sagnac干涉环实现选频和调谐的环形腔掺铒光纤激光器.理论模拟了PMF和PC对波长的控制作用.实验中调节PC得到了单波长、双波长和多波长激光;并验证了滤波间隔随PMF长度的变化规律.实验中得到了斜率效率20%,3 dB线宽0.016 nm,30 dB线宽0.097 nm,边模抑制比（SMSR）40 dB左右的稳定激光输出. 关键词： 光纤激光器 Sagnac干涉环 环形腔 掺铒光纤     

Stable dual-wavelength single-longitudinal-mode ring erbium-doped fiber laser for optical generation of microwave frequency

We demonstrate a simple dual-wavelength ring erbium-doped fiber laser operating in single-longitudinal-mode (SLM) at room temperature. A pair of reflection type short-period fiber Bragg gratings (FBGs), which have two different center wavelengths of 1545.072 and 1545.284 nm, are used as the wavelength-selective component of the laser. A segment of unpumped polarization maintaining erbium-doped fiber (PM-EDF) is acted as a narrow multiband filter. By turning the polarization controller (PC) to enhance the polarization hole burning (PHB), the single-wavelength and dual-wavelength laser oscillations are observed at 1545.072 and 1545.284 nm. The output power variation is less than 0.6 dB for both wavelengths over a five-minute period and the optical signal to noise ratio (OSNR) is greater than 50 dB. By beating the dual-wavelengths at a photodetector (PD), a microwave signal at 26.44 GHz is demonstrated.     

Simple tunable multiwavelength Brillouin/Erbium fiber laser utilizing short-length photonic crystal fiber

We have demonstrated a simple ring cavity tunable multiwavelength Brillouin/Erbium fiber laser (MWBEFL), in which 70 m highly nonlinear photonic crystal fiber (HNL-PCF) is used as the Brillouin gain medium. The fiber laser utilizes recycling mechanism to enhance stimulated Brillouin scattering (SBS). The configuration that consists of only 3 optical components is easy to be integrated and improves the practicality. At the maximum 1480 nm pump power of 110 mW and the Brillouin pump power of 3 dBm, 10 stable output channels with more than 10 dB optical signal to noise ratio (OSNR) and 0.078 nm channel spacing could achieve 10 nm tuning ranges.     

Tunable microwave generation based on a Brillouin fiber ring laser and reflected pump

A simple approach for photonic generation of a tunable microwave signal is proposed and successfully demonstrated. By mixing the output from a single-longitudinal-mode Brillouin fiber ring laser with the reflected laser pump at photodetector, a microwave signal at the Brillouin shift can be obtained. Since the Brillouin shift can be changed by tuning the pump wavelength, tunable microwave can be generated. As a result a microwave signal tunable from 10.39 to 10.67 GHz has been achieved, with linewidth less than 600 KHz.     

Bi-directional dual-wavelength Brillouin lasing in a hybrid fiber ring cavity

In this paper, a novel Brillouin fiber laser (BFL) is proposed based on the hybrid fiber ring cavity composed of two types of fibers with different Brillouin shifts. Single mode fiber (SMF) and truewave fiber (TWF) are used in our experiments. Bi-directional dual-wavelength Brillouin lasing is achieved in the hybrid fiber ring cavity. The lasing lights along the two directions come from the Stokes waves generated in the two fibers, respectively, with different Brillouin shifts, however, they share the same fiber ring cavity. The BFL based on the hybrid fiber ring cavity provides a simple possible way to realize Brillouin fiber optical gyroscopes (BFOGs) without lock-in effect.     

Dual-wavelength Brillouin ring-cavity fiber laser with tunable channel spacing

We experimentally demonstrate a dual-wavelength Brillouin fiber laser configured a pre-amplified Brillouin pump and FBG filter in a ring-cavity. The Brillouin laser can generate 21 Brillouin Stokes with 0.084 nm spacing, the first-Stoke has a peak power of 2.19 dBm. By adjusting the TLS wavelength and FBG’s reflection wavelength from circulating in the ring-cavity, the generated output dual-wavelength is stabile and the channel spacing is tunable, the widest and narrowest channel spacing obtained is approximately 1.12 nm (139 GHz) and 0.084 nm (10.5 GHz).     

Stable Dual-Wavelength Fibre Laser with Bragg Gratings Fabricated in a Polarization-Maintaining Erbium-Doped Fibre

A new polarization-independent duai-wavelength fibre laser by fabricating a uniform FBG and a chirped FBG in a polarization-maintaining erbium-doped fibre （PM-EDF） is proposed and demonstrated. The wavelength spacing is 0.18nm and the optical signal-to-noise ratio is greater than 50dB with pump power of 246mW. Chirped FBG is used to make the reflectivity wavelengths of two PM-FBGs match easier. Since both EDF and FBGs are polarization-maintaining without splices and the two wavelengths are polarization-independent, the maximum amplitude variation and wavelength shifts for both lasing wavelength with 3-min intervals over a period of six hours are less than 0.2 dB and 0.005 nm, respectively, which shows stable dual-wavelength output.     

A tunable multi-wavelength Brillouin–erbium fiber laser with fourfold Brillouin frequency spacing

We have experimentally demonstrated a tunable multi-wavelength Brillouin–erbium fiber laser with over 40 GHz spacing utilizing two cascaded double Brillouin-frequency-spacing cavities. In this laser configuration, two segments of 25 km-long single-mode fibers are used as Brillouin gain medium in each ring cavity, and a segment of 8 m-long erbium-doped fiber with 980 nm pump is employed to amplify Brillouin pump (BP). At BP wavelength of 1550 nm, BP power of 8.3 dBm (6.8 mW) and the maximum 980 nm pump power of 27.78 dBm (600 mW), seven output channels with fourfold Brillouin-frequency spacing, and the tuning range of 15 nm from 1545 to 1560 nm are achieved. The proposed multi-wavelength Brillouin–erbium fiber laser has wide applications, such as in microwave signal generation and optical communications.     

Multi-wavelength Brillouin fiber laser using dual-cavity configuration

A simple technique for achieving multi-wavelength tunable multi-wavelength Brillouin fiber laser (BFL) based on dual-pass configuration is demonstrated. The BFL uses a piece of 10 km long non-zero dispersion shifted fiber (NZ-DSF) as a Brillouin gain medium to obtain odd-order Brillouin Stokes waves as an output with the line spacing of 0.16 nm (20 GHz) between each two consecutive waves by employing even-order Brillouin Stokes to improve output performance of the laser. With a BP of 15.3 dBm, at least 15 odd-order Brillouin Stokes and anti-Stokes lines are generated. The laser is room temperature stable, tunable over 50 nm wavelength range and has an optical signal to noise ratio of more than 30 dB at 1560 nm region. This Brillouin fiber laser can operate at any wavelength depending on the Brillouin pump (BP) wavelength used.