长江下游下蜀黄土的稀土元素物源判别

通过对长江下游镇江、福家湾、新港、芜湖、福路镇等地区下蜀黄土中稀土元素的研究,结合长江古漫滩堆积物及北方黄土沉积物,对下蜀黄土进行了物源判别,得出：下蜀黄土与长江河漫滩之间的各稀土元素的 DF 值绝大部分小于0．2,表现出在各个稀土元素上与河漫滩的接近程度较大,而与北方黄土接近程度较小;由物源指数 PI 计算得出,新港、福路镇、镇江下蜀黄土 PI 值均在0．2附近,表现出下蜀黄土与河漫滩在稀土元素总体上的相似程度极高,物源判别为长江河漫滩;福家湾下蜀黄土物源判别为北方黄土,北方黄土对其有一定影响。总体上,长江下游下蜀黄土受到北方黄土与河漫滩的影响,其中以长江河漫滩影响为主。     

Effect of salts on water viscosity in narrow membrane pores

The effect of various salts on the viscosity, and by implication structure, of water in polymeric membrane pores of radius approximately 1.69 nm and low charge density has been studied. Permeation of pure water and various electrolyte solutions was analyzed using the Hagen-Poiseuille equation expressed in a ratio form to exclude membrane-specific quantities such as pore radius and length. The analysis produced viscosity ratios of electrolyte to pure water inside the membrane pores. Comparing the viscosity ratios inside the pores with their bulk counterparts showed that confinement significantly increased the sensitivity of water structure to the presence of ions. It has been found that, in relative terms in the pores, Cl- was a strong structure breaker, K+ was a moderately strong structure breaker, Na+ was a weak structure breaker, SO4(2-) was a weak structure maker, and Mg2+ was a strong structure maker. Predictive modeling of membrane separation performance would benefit from such effects being taken into account in cases where the pore ion concentrations may be high.     

Staphylococcus aureus bicomponent gamma-hemolysins, HlgA, HlgB, and HlgC, can form mixed pores containing all components

Staphylococcal gamma-hemolysins are bicomponent toxins forming a protein family with leucocidins and alpha-toxin. Two active toxins (AB and CB) can be formed combining one of the class-S components, HlgA or HlgC, with the class-F component HlgB. These two gamma-hemolysins form pores with marked similarities to alpha-toxin in terms of conductance, nonlinearity of the current-voltage curve, and channel stability in the open state. AB and CB pores, however, are cation-selective, whereas alpha-toxin is anion-selective. gamma-Hemolysins' pores are hetero-oligomers formed by three or four copies of each component (indicated as 3A3B and 3C3B or 4A4B and 4C4B). Point mutants located on a beta-strand of the class-S component that forms part of the protomer-protomer contact region can prevent oligomer assembly. Interestingly, these mutants inhibit growth of pores formed not only by their natural components but also by nonstandard components. This lead to the hypothesis that mixed ABC pores could also be formed. By studying the conductance of pores, assembled in the presence of all three components (in different ratios), it was observed that the magnitudes expected for mixed pores were, indeed, present. We conclude that the gamma-hemolysin/leucocidin bicomponent toxin family may form a larger than expected number of active toxins by cross-combining various S and F components.     

Critical study of the interference of silicic derivatives on fluoride determination

Several physical properties of various silicic derivatives are examined in order to elucidate an interference with fluoride during codistillation of hexafluorosilicic acid with superheated steam.The stated interference cannot be explained by the granulometry or by the specific surface area of the interfering derivatives but their porous structure: a nonporous adsorbent (silica) does not interfere; a porous adsorbent (silicic acid and silica gel) is liable to interfere when its pores reach a definite size, approximately a diameter of 50 Å.The occurrence of imprisonment of some fluoride anions in the pores of the interfering silicic derivatives is suggested.     

Pore formation in fluctuating membranes

We study the nucleation of a single pore in a fluctuating lipid membrane, specifically taking into account the membrane fluctuations, as well as the shape fluctuations of the pore. For large enough pores, the nucleation free energy is well-described by shifts in the effective membrane surface tension and the pore line tension. Using our framework, we derive the stability criteria for the various pore formation regimes. In addition to the well-known large-tension regime from the classical nucleation theory of pores, we also find a low-tension regime in which the effective line and surface tensions can change sign from their bare values. The latter scenario takes place at sufficiently high temperatures, where the opening of a stable pore of finite size is entropically favorable.     

浸没凝胶相转化制备聚合物膜的孔结构及其形成机理

全面地综述了浸没凝胶相转化法制备的聚合物微孔膜的表面和膜中存在的各种孔的结构和形态,从制膜体系的热力学性质和成膜动力学角度解释了各种孔结构形态的形成和生长机理,即膜表面与膜中孔的结构形态由此时制膜体系发生的相分离类型决定,由此可推断出不同的膜层可能有不同的成膜机理。因此,只要掌握了各种膜孔结构形成的机理,通过改变膜的制备条件,控制体系的热力学性质与成膜时动力学扩散是可以实现相转化膜结构的控制。     

ANISOTROPY OF MAGNETIC SUSCEPTIBILITY AND ORIGIN OF THE CHINESE LOESS AND ITS SIGNIFICANCE TO THE QUATERNARY RESEARCH*

Anisotropy of magnetic susceptibility is used in the present study to reveal thedepositional fabric on the original (windblown) loess and secondary (redeposited) loess. The two kinds of sediments mentioned above can be distinguished in terms of their susceptibility anisotropy, e.g. anisotropy degree, magnetic foliation and lineation parameters. On this basis the magnetic fabric of the Pliocene red soil underlaying the loess is studied, and compared with the results of a typical residue-deposited red clay in South China. Considering its geological features, the red soil in Xifeng is regarded probably as aeolian in origin also.     

Adsorbate layering in narrow-pore materials

The conditions of layering of adsorbate molecules in porous systems with characteristic sizes of from 1 to 50–100 nm are discussed. The porous systems contain both very narrow pores, in which interaction potentials of pore walls overlap, and comparatively broad pores without overlapping of surface potentials. Three pore size intervals are distinguished. In the first interval, no adsorbate layering occurs, the second interval is characterized by capillary condensation with critical parameters different from their volume values, and, in the third interval, capillary condensation conditions are almost the same as in the volume adsorbtive phase. Criteria of the characteristic pore sizes of different geometries are formulated; the criteria correspond to small volumes in which first-order phase transitions are absent. The boundary between the first and second pore size regions is observed experimentally as the disappearance/appearance of hysteresis loops in adsorption-desorption isotherms measured under strictly equilibrium conditions as the size of pores decreases/increases. A nonuniform distribution of the surface potential is shown to be responsible for the multiplicity of local regions in porous media with their own vapor-liquid coexisting phases. The spinodal transitions in adsorption-desorption in pores can occur between various local regions. An analysis is performed in terms of the lattice gas model with short-range Lennard-Jones interaction of adsorbate molecules with each other and adsorbent walls.     

Poly(choloyl)-based amphiphiles as pore-forming agents: transport-active monomers by design

This paper describes the design and synthesis of a family of pore-forming amphiphiles. Two of these amphiphiles, which are derived from cholic acid, lysine, and p-phenylenediamine, can produce pores in lipid bilayers as individual molecules. In sharp contrast, analogous amphiphiles that do not contain a rigid 1,4-phenylenediamide moiety favor the formation of dimer-based pores. Kinetic evidence in support of monomer- and dimer-based pores has been obtained from Na+ transport measurements across bilayers made from 1-palmitoyl-2-oleoyl-2-sn-glycero-3-phosphocholine (POPC). Structure-activity studies that have been carried out with pore-forming, dimer-based amphiphiles have also revealed a significant activity dependence on their overall compactness. The practical potential of pore-forming amphiphiles with controllable supramolecular properties is briefly discussed.     

Grafted macroporous polymer monolithic disks: a new format of scavengers for solution-phase combinatorial chemistry

Polyethylene encased porous poly(chloromethylstyrene-co-divinylbenzene) disks have been prepared by polymerization in a cylindrical glass mold and cut to a disk format. Following attachment of a free radical azo initiator 4,4'-azobis(4-cyanovaleric acid) to available functionalities at the surface of the pores, the polymerization of 2-vinyl-4,4-dimethylazlactone was initiated from the surface. To avoid an undesirable increase in flow resistance and to improve the yield of grafting, divinylbenzene was added to the polymerization mixture in order to form a layer of swellable reactive polymer gel within the pores. The use of these disks as scavenging filters to remove various amines from solutions in flow-through operations was demonstrated by effective removal of amines in a very short period of time from their solutions in a variety of solvents, even including alcohols and water.     

Comparison of deconvoluted plasma DSC curves on patients with solid tumors

Melting of crystalline compounds inside the nanopores of open-morphology porous systems was studied on a model system, consisted of 1-octadecene and silica gels with different pore sizes, by means of thermogravimetry, differential scanning calorimetry and powder X-ray diffraction. The parameters of silica gels porous structure (surface area, pore size and volume) were calculated using N₂ adsorption data. To describe the experimental results, a new thermodynamic model of crystallites melting inside the nanopores of irregular shape was established. This model allows an analytical prediction for the shift of phase transition temperature and melting enthalpy (latent heat of melting) due to the surface tension effects. To a first approximation, both parameters must linearly depend on the specific ratio of the total surface of pores to their total volume, and experimental studies have mostly confirmed this result for the melting of 1-octadecene confined inside the pores of a wide range of various silicas (with the pores of different sizes and geometry).

     

Shrinkage effects in photopolymerizable resins containing filling agents: Application to stereophotolithography

The influence of porous additives with various structures on the shrinkage of resins used for stereolithographic applications was studied by measuring the dependence of the specific gravity of the charged polymer material as a function of the charge fraction. The investigations were conducted on difunctional monomers photopolymerized either by a radical (acrylate) or a cationic (epoxy) mechanism. The improvement resulting from the incorporation of charges in the formulation is accounted for in a semi-quantitative way by an adsorption-desorption equilibrium of monomer molecules between the pores and the bulk phase. Thus, the pores of the charges which are initially filled with monomer molecules play the role of buffers which discharge their content as the photopolymerization develops in the liquid phase. It is also worth mentioning that the viscosities of the photosensitive charged resins used in these experiments are quite suitable for use in stereophotolithography. © 1992 John Wiley & Sons, Inc.     

The Size Statistics of Nuclear Track Holes on the Track Membrane Surface

Areal distribution functions of double and triple pores and their first moments were obtained within the framework of the statistical model of overlapping nuclear track pores (circular holes of equal diameter on the flat surface of a track membrane). The linear dimensions of multiple pores with reference to their configuration forms (for triplets) and their dependence of on membrane porosity were calculated.     

Thermodynamic pressure of simple fluids confined in cylindrical nanopores by isothermal-isobaric Monte Carlo: influence of fluid/substrate interactions

The thermodynamic pressure or grand potential density is calculated by isobaric-isothermal Monte Carlo algorithm for simple Lennard-Jones fluid confined in cylindrical pores presenting chemical heterogeneities along their axis. Heuristic arguments and simulation results show that the thermodynamic pressure of the confined fluid contains two contributions. The first term is the usual pressure of the bulk fluid for a density equal to the confined fluid density defined as the total number of confined particles divided by the accessible volume due to thermal agitation. A second term has to be added, which is empirically shown to be proportional to the fluid/wall interface area and almost constant along the adsorption and desorption branches. This interfacial contribution, calculated for various pore models, has small variations reminiscent of the fluid adsorption/desorption properties calculated in the various pores. In particular, it is shown that this interfacial quantity is maximum for a fluid/substrate interaction intensity of the same order as the fluid/fluid one, while the thermodynamic pressure at which rapid desorption occurs presents a minimum. Stronger or weaker fluid/wall affinity favors gas state nucleation on the desorption of confined fluids.     

Application of anodic dissolution method for a study of electrocolored aluminum oxides

The anodic dissolution of color carrier of colored aluminum anodic oxide films (AOF) is studied before and after their coloring, using ac in various electrolytes containing Cu(II). The voltammetric polarization curves of anodic dissolution of colored AOF in 0.1 M H₂SO₄ depend on the amount of copper deposited in the pores and its oxidation state (Cu, Cu₂O, CuO). Analytical and X-ray diffraction examination of AOF prior to and after the anodic dissolution shows that the anodic dissolution method is inapplicable for the determination of the oxidation state of copper electrodeposited in AOF pores or the amount of copper oxides.     

分子筛限域金属纳米粒子及其氧化还原反应应用的研究进展

沸石分子筛是一类孔隙均匀、结晶度高、结构多样、比表面积大的材料,在催化、分离、吸附等方面得到了广泛的应用。沸石分子筛已被证明是金属纳米粒子(MNPs)的理想载体。金属纳米粒子@沸石分子筛催化剂不仅表现出优异的催化活性,而且具有较高的稳定性和择形催化性。此外,限域的金属纳米粒子与具有活性位点的纳米孔骨架的协同作用可以进一步提高复合催化剂的催化活性。金属纳米粒子@沸石分子筛催化剂由于具有较高的活性、择形性和热稳定性等优点,在工业相关应用中引起了人们的极大关注。本文综述了金属纳米粒子@沸石分子筛催化剂的研究进展,重点介绍了多种合成方法以及其在氢化和氧化反应中的应用进展。指出了金属纳米粒子@沸石分子筛催化剂领域存在的问题和挑战并对其未来发展进行展望。     

A Study on the Generating Mechanism of Vertical Joints in Loess

Based on field investigation, theoretical analysis and model testing, the authors believe that the horizontal tensile stress caused by gravity at the top and bottom of big voids or holes is the primary rea-. son for the generation of vertical joints in loess. This paper explains the generation mechanism of vertical joints in loess from the viewpoint of mechanics for the first time.     

Metal–organic frameworks and their catalytic applications

Metal-organic frameworks (MOFs), as a novel categories of porous and well crystalline materials, were gained significant interest in the current years. These materials offer practical implementations in different sectors, like hydrogen and carbon dioxide storage, catalysis and separation due to their superior porosity, great surface area and versatile framework. The current review outlines the existing state of the art in using MOFs as catalysts in various organic transformation processes and photocatalysis depending on the site form, with particular confirmation on the most recent techniques for increasing the active centers and modifying their performance, by deposition of metallic nanoparticles on its surface or within the pores. In addition, the substantial progress made in the production of various composites containing MOF with particular focus on preparation and catalytic applications was provided.