Formation and characterization of high surface area thermally stabilized titania/silica composite materials via hydrolysis of titanium(IV) tetra-isopropoxide in sols of spherical silica particles

A direct synthetic route leading to titania particles dispersed on nonporous spherical silica particles has been investigated; 5, 10, and 20% (w/w) titania/silica sols mixtures were achieved via hydrolyzation of titanium tetra-isopropxide solution in the mother liquor of a freshly prepared sol of spherical silica particles (St?ber particles). Titania/silica materials were produced by subsequent drying and calcination of the xerogels so obtained for 3 h at 400 and 600 degrees C. The materials were investigated by means of thermal analyses (TGA and DSC), FT-IR, N(2) gas adsorption-desorption, powder X-ray diffraction (XRD), and transmission electron microscopy (TEM). In spite of the low surface area (13.1 m(2)/g) of the pure spherical silica particles calcined at 400 degrees C, high surface area and mesoporous texture titania/silica materials were obtained (e.g., S(BET) ca. 293 m(2)/g for the 10% titania/silica calcined at 400 degrees C). Moreover, the materials were shown to be amorphous toward XRD up to 600 degrees C, while reasonable surface areas were preserved. It has been concluded that dispersion of titania particles onto the surface of the nonporous spherical silica particles increase their roughness, therefore leading to composite materials of less firm packing and mesoporosity.     

Synthesis of titania/polymer core-shell hybrid microspheres

Monodisperse titania/polymer core-shell microspheres were prepared by a two-stage reaction with titania as core and poly(ethyleneglycol dimethacrylate) (PEGDMA) as shell, in which the titania cores were synthesized by a sol-gel method and subsequently grafted with 3-trimethoxysilyl methacrylate as the first-stage reaction to incorporate the vinyl groups on the surface of inorganic core. The PEGDMA shell was then encapsulated over the MPS-modified titania core by distillation precipitation polymerization of ethyleneglycol dimethacrylate in neat acetonitrile during the second-stage polymerization via capture of the radicals of EGDMA with the aid of the reactive vinyl groups on the surface of inorganic core without any stabilizer or surfactant. The shell thickness of the core-shell hybrid microspheres was controlled by the feed of EGDMA monomer during the polymerization. The resultant titania particles and core-shell microspheres were studied by transmission electron microscopy, Fourier-transform infrared spectra, X-ray photoelectron spectroscopy, and thermogravimetric analysis.     

Preparation and characterization of vanadium oxide deposited on thermally stable mesoporous titania

Vanadium oxide was deposited on mesoporous titania by the molecular designed dispersion method to investigate the potential properties of these catalysts. Mesoporous titania was synthesized following the evaporation-induced self-assembly (EISA) method with a subsequent treatment with ammonia to increase the thermal stability. As a result, the mesoporous titania obtained shows a high surface area (approximately 350 m2/g) and high stability. Vanadium oxide was deposited by the MDD method using a vanadyl acetylacetonate complex that was transformed into VOx after a controlled calcination in air flow at 300 degrees C. The mesostructure and porosity characteristics of titania remain even until the maximum V-loading was reached (0.4 mmol/g), as it was shown by N2 sorption measurements at -196 degrees C. The catalysts were characterized by chemical analysis, Fourier transform infrared-photoacoustic spectroscopy (FTIR-PAS), UV-vis diffuse reflectance (DR), and Fourier transform Raman spectroscopy. Raman spectra showed isolated V species for the different V-containing catalysts. Furthermore, UV-vis-DR revealed a higher contribution of polymeric species as the V loading increases. The VOx/mesoporous titania catalysts were highly active in the selective catalytic reduction of NOx. A high activity in the NO conversion was observed, which increases with increasing metal loading.     

Synthesis of titania-silica core-shell microspheres via a controlled interface reaction in a microfluidic device

In this work, we describe a novel, simple microfluidic method for fabricating titania-silica core-shell microspheres. Uniform droplets of silica sol were dispersed into an oil phase containing tetrabutyl titanate via a coaxial microfluidic device. The titanium alkoxide hydrolyzed at the water-oil interface after the formation of the aqueous droplets. A gel shell containing the titanium hydroxide formed around the droplets, and the titania-silica core-shell microspheres were obtained after calcinations. The X-ray diffraction results show that titania coatings crystallized into a pure anatase structure. The scanning electron microscopy and energy-dispersive spectrometry characterization shows that the microspheres are monodispersed with uniform titania coating on the surface. The dispersity and size of the microspheres could easily be controlled by changing the microfluidic flow parameters. The titania content on the surface could be adjusted in the large range of 1.0-98.0 mol % by varying the continuous phase composition and the reaction time, and the structures of the core-shell microshperes could also be controlled.     

Application of liquid phase deposited titania nanoparticles on silica spheres to phosphopeptide enrichment and high performance liquid chromatography packings

A novel core-shell composite (SiO(2)-nLPD), consisting of micrometer-sized silica spheres as a core and nanometer titania particles as a surface coating, was prepared by liquid phase deposition (LPD). Here, we show the resulting core-shell composite to have better efficient and selective enrichment for mono- and multi-phosphopeptides than commercially available TiO(2) spheres without any enhancer. The material exhibited favorable characteristics for HPLC, which include narrow pore size distribution, high surface area and pore volume. We also show that the core-shell composite can efficiently separate adenosine phosphate compounds due to the Lewis acid-base interaction between titania and phosphate group when used as HPLC packings. After coating the silica sphere with titania by LPD, the silanol of silica spheres will be shielded and that the stationary phase, C(18) bonded SiO(2)-3LPD, could be used under extreme pH condition.     

Preparation of titania-coated polystyrene particles in mixed solvents by ammonia catalysis

A mixed-solvent method was developed to coat polystyrene (PS) spheres with smooth, homogeneous shells of amorphous titania by ammonia catalysis. The TEM images showed that, in the presence of ammonia, the thickness of titania shells could be controlled in the range of 8-65 nm by varying the concentration of titanium tetrabutoxide (TBOT) in the ethanol/acetonitrile mixed solvents with an appropriate volume ratio. The diffusion-controlled mechanism of the mixed solvents and the catalysis mechanism of ammonia were investigated. After the calcination of core-shell particles for 2 h at 500 degrees C, spherical hollow titania shells could be obtained, and the surfaces of the particles remained quite smooth and homogeneous. The XRD analysis indicated that calcination promoted the transformation of amorphous titania into an anatase phase.     

Surfactant mediated synthesis of spherical binary oxides photocatalytic with enhanced activity in visible light

Spherical silica and zirconia mixed titania and pure titania samples were prepared in presence of cetyltrimethylammonium bromide (CTAB) through controlled hydrolysis of corresponding metal alcoxides. Effect of surfactant amount and calcinations temperature on morphology, surface area and photocatalytic activity is studied using PXRD, SEM, FTIR, Solid state UV-vis spectroscopy and BET surface area. It is well observed that in presence of 2 mol% CTAB, uniform sized spherical oxide particles can be synthesized. However, increasing or decreasing the surfactant amount does not favor the spherical particle formation. Material synthesis in presence of CTAB not only helps in the spherical particle formation but also increases the surface area and visible light absorption. Studies on photocatalytic lead removal with respect to calcination temperature indicate that the calcination at 500 degrees C is most suitable for the best photocatalytic activity. Mixing of zirconia and silica helps in anatase phase stabilization even at 900 degrees C calcination. Accordingly low decrease in surface area even at 900 degrees C calcination is observed. Due to the phase stabilization and higher surface area binary oxide materials showed comparatively better photocatalytic activity even after calcination at 900 degrees C. So it can be concluded that present synthesis approach can produce uniform sized spherical binary oxide materials with better photocatalytic activity in visible light.     

Structural and adsorption characteristics and catalytic activity of titania and titania-containing nanomaterials

Morphological, structural, adsorption, and catalytic properties of highly disperse titania prepared using sulfate and pyrogenic methods, and fumed titania-containing mixed oxides, were studied using XRD, TG/DTA, nitrogen adsorption, (1)H NMR, FTIR, microcalorimetry on immersion of oxides in water and decane, thermally stimulated depolarization current (TSDC) and catalytic photodecomposition of methylene blue (MB). Phase composition and aggregation characteristics of nanoparticles (pore size distribution) of sulfate and pyrogenically prepared titania are very different; temperature dependent structural properties are thus very different. Catalytic activity for the photodecomposition of MB is greatest (per gram of TiO(2) for the pure oxide materials) for non-treated ultrafine titania PC-500, which has the largest S(BET) value and smallest particle size of the materials studied. However, this activity calculated per m(2) is higher for PC-105, possessing a much smaller S(BET) value than PC-500. The activity per unit surface area of titania is greatest for the fumed silica-titania mixed oxide ST20. Calcination of PC-500 at 650 degrees C leads to enhancement of anatase content and catalytic activity, but heating at 800 and 900 degrees C lowers the anatase content (since rutile appears) and diminishes catalytic activity, as well as the specific surface area because of nanoparticle sintering.     

Catalytic activity during copolymerization of ethylene and 1-hexene via mixed TiO2/SiO2-supported MAO with rac-Et[Ind]2ZrCl2 metallocene catalyst

Activities during ethylene/1-hexene copolymerization were found to increase using the mixed titania/silica-supported MAO with rac-Et[Ind]2ZrCl2 metallocene catalyst. Energy Dispersive X-ray spectorcopy (EDX) indicated that the titania was apparently located on the outer surface of silica and acted as a spacer to anchor MAO to the silica surface. IR spectra revealed the Si-O-Ti stretching at 980 cm(-1) with low content of titania. The presence of anchored titania resulted in less steric hindrance and less interaction due to supporting effect.     

Photocatalytic properties of Ru-doped titania prepared by homogeneous hydrolysis

Nanocrystalline titania particles doped with ruthenium oxide have been prepared by the homogenous hydrolysis of TiOSO₄ in aqueous solutions in the presence of urea. The synthesized particles were characterized by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HRTEM), Selected Area Electron Diffraction (SAED) and Nitrogen adsorption-desorption was used for surface area (BET) and porosity determination (BJH). The photocatalytic activity of the Ru-doped titania samples were determined by photocatalytic decomposition of Orange II dye in an aqueous slurry during irradiation at 365 nm and 400 nm wavelengths.      

二氧化钛与碳化钨纳米复合材料制备及其对甲醇的电催化氧化活性

以市售纳米二氧化钛(TiO2)为载体,六氯化钨为钨源,将浸渍法与原位还原碳化技术相结合制备了核壳结构碳化钨(WC)/TiO2纳米复合材料;应用X射线衍射分析、透射电子显微镜、高分辨扫描透射成像和X射线能量散射谱等手段对样品晶相、形貌、微结构和化学组成等特征进行了表征.结果表明,样品的晶相由金红石型TiO2、Ti4O7、WC、W2C和WxC构成,钨碳化物负载于钛氧化物外表面,构成比较典型的核壳结构.采用三电极体系和循环伏安法测试了样品在碱性溶液中对甲醇的电催化氧化活性,结果表明,相比于纯碳化钨和二氧化钛,复合材料的电催化活性得到了明显的提升.样品电催化活性的提升与前驱体钨钛摩尔比、还原碳化时间、核壳结构壳层的完整性和晶相组成以及核壳结构中二氧化钛和碳化钨之间的协同效应有关.这说明金红石是能够提升碳化钨电催化氧化活性的载体材料之一.     

Comparison of rhodamine B degradation under UV irradiation by two phases of titania nano-photocatalyst

Titania (TiO₂) nano-photocatalysts, with different phases, prepared using a modified sol?Cgel process were employed in the degradation of rhodamine at 10?mg?L^?1 concentration. The degradation efficiency of these nano-photocatalysts was compared to that of commercial Degussa P25 titania. It was found that the nanocatalysts calcined at 450?°C and the Degussa P25 titania had similar photoreactivity profiles. The commercial Degussa P25 nanocatalysts had an overall high apparent rate constant of (K _app) of 0.023?min^?1. The other nanocatalyst had the following rate constants: 0.017, 0.0089, 0.003 and 0.0024?min^?1 for 450, 500, 550 and 600?°C calcined catalysts, respectively. This could be attributed to the phase of the titania as the anatase phase is highly photoactive than the other phases. Furthermore, characterisation by differential scanning calorimetry showed the transformation of titania from amorphous to anatase and finally to rutile phase. SEM and TEM characterisations were used to study the surface morphology and internal structure of the nanoparticles. BET results show that as the temperature of calcinations was raised, the surface area reduced marginally. X-ray diffraction was used to confirm the different phases of titania. This study has led to a conclusion that the anatase phase of the titania is the most photoactive nanocatalyst. It also had the highest apparent rate constant of 0.017?min^?1, which is similar to that of the commercial titania.     

High surface area sol–gel alumina–titania nanocatalyst

Alumina–titania mixed oxide nanocatalysts with molar ratios = 1:0.5, 1:1, 1:2, 1:5 have been synthesized by adopting a hybrid sol–gel route using boehmite sol as the precursor for alumina and titanium isopropoxide as the precursor for titania. The thermal properties, XRD phase analysis, specific surface area, adsorption isotherms and pore size details along with temperature programmed desorption of ammonia are presented. A specific surface area as high as 291 m²/g is observed for 1:5 Al₂O₃/TiO₂ composition calcined at 400 °C, but the same composition when calcined at 1,000 °C, resulted in a surface area of 4 m²/g, while 1:0.5 composition shows a specific surface area of 41 m²/g at 1,000 °C. Temperature programmed desorption (of ammonia) results show more acidic nature for the titania rich mixed oxide compositions. Transmission electron microscopy of low and high titania content samples calcined at 400 °C, shows homogeneous distribution of phases in the nano range. In the mixed oxide, the particle size ranges between 10–20 nm depending on titania content. The detailed porosity data analysis contributes very much in designing alumina–titania mixed oxide nanocatalysts.     

Core-shell nanorods of SnS-C and SnSe-C: synthesis and characterization

The straightforward, efficient, solventless, RAPET (reactions under autogenic pressure at elevated temperature) approach was explored for the fabrication of core-shell nanomaterials. Carbon-encapsulated SnS and SnSe nanorods were synthesized by a one-step thermal decomposition of tetramethyltin in the presence of either S or Se powder in a closed reactor at 700 degrees C for 40 min, under their autogenic pressure in an inert atmosphere. The powder X-ray diffraction measurements provided structural evidence for the formation of pure orthorhombic phases of SnS or SnSe particles. The Raman spectroscopy measurements ensured that the nature of the coated carbon was semigraphitic. The scanning electron micrographs verified the 1D morphology of the formed SnS and SnSe chalcogenides, and their stoichiometry was confirmed by EDAX measurements. The HR-TEM micrographs distinguished between core and shell morphologies. The nitrogen gas adsorption on the surface of core-shell nanostructures was determined by BET surface area analysis. The plausible mechanism for the creation of chalcogenide cores (SnS or SnSe) with a carbon shell was elucidated.     

Preparation and solution behavior of a thermoresponsive diblock copolymer of poly(ethyl glycidyl ether) and poly(ethylene oxide)

A thermoresponsive diblock copolymer, poly(ethyl glycidyl ether)-block-poly(ethylene oxide) (PEGE-b-PEO), is synthesized by successive anionic ring-opening polymerization of ethyl glycidyl ether and ethylene oxide using 2-phenoxyethanol as a starting material, and its solution behavior is elucidated in water. In a dilute 1 wt % solution, the temperature-dependent alteration in the polymer hydrodynamic radius (RH) is measured in the temperature range between 5 and 45 degrees C by pulse-gradient spin-echo NMR and dynamic light scattering. The RH value increased with temperature in two steps, where the first step at 15 degrees C corresponds to the core-shell micelle formation and the second step at 40 degrees C corresponds to the aggregation of the core-shell micelles. The formation of the core-shell micelles is supported by the solubilization of a dye (1,6-diphenyl-1,3,5-hexatriene) in the hydrophobic core, which is recognized for a copolymer solution in the temperature range between 20 and 40 degrees C. In this temperature range, the core-shell micelles and the unimers coexist and the fraction of the former gradually increases with increasing temperature, suggesting equilibrium between the micelles and the unimers. In the concentrated regime (40 wt % solution), the solution forms a gel and the small-angle X-ray scattering measurements reveal the successive formation of hexagonal and lamellar liquid crystal phases with increasing temperature.     

SiO2含量对钛/硅复合氧化物聚酯催化剂性能的影响

研究了钛/硅复合氧化物聚酯催化剂中,二氧化硅含量对聚对苯二甲酸乙二醇酯缩聚反应的影响.催化剂XRD谱图表示,增加二氧化硅含量会抑制二氧化钛的结晶.随着二氧化硅含量的增加,钛/硅催化剂表面Lewis酸的数目和强度都减小.比表面积和Lewis表面酸性都会影响钛/硅催化剂的活性.     

Unusual crystallization behaviors of anatase nanocrystallites from a molecularly thin titania nanosheet and its stacked forms: increase in nucleation temperature and oriented growth

Crystallization behaviors of anatase nanocrystallites from an ultrathin two-dimensional reactant composed of exfoliated titania nanosheets have been studied by monitoring the heating process of their well-organized films, with which the film thickness can be controlled from a molecularly thin monolayer to a stacked multilayer structure with a stepwise increment of approximately 1 nm. The heated products were identified by means of total reflection fluorescence X-ray absorption near-edge structure analysis and in-plane X-ray diffraction measurements using a synchrotron radiation source. The films composed of five or more layers of stacked nanosheets were transformed into anatase at 400-500 degrees C, which is a normal crystallization temperature of anatase from bulk reactants. As the film became thinner by decreasing the number of nanosheet layers to five or less, the crystallization temperature was found to increase and finally reached 800 degrees C for the monolayer film. Interestingly, preferential growth of anatase along the c-axis was strongly promoted for these ultrathin films. These unusual behaviors may be understood in terms of crystallization from the two-dimensional system of scarcely distributed reactants. The titania nanosheet crystallite is much thinner than the unit cell dimensions of anatase, and therefore, extensive atomic diffusion is required for the transformation particularly for the ultrathin films with a critical number (2-3) of stacked nanosheet layers. There is some structural similarity between anatase and titania nanosheet, which may account for the oriented growth of anatase nanocrystallites.     

X-ray diffraction area mapping of preferred orientation and phase change in TiO2 thin films deposited by chemical vapor deposition

This paper reports on an investigation into the formation of TiO(2) thin films, whereby X-ray diffraction is used to map systematic changes in preferred orientation and phase observed throughout the films. The key to this strategy is the recording of X-ray diffraction patterns of specific and isolated areas of a substrate, ensuring this specificity by the use of a small X-ray sample illumination area (approximately 3-5 mm(2)). A map of the variation in film composition can then be built up by recording such diffraction patterns at regular intervals over the whole substrate. Two titania films will be presented, grown using atmospheric pressure chemical vapor deposition, at 450 and 600 degrees C, from TiCl(4) and ethyl-acetate precursors. The film grown at 450 degrees C showed a systematic change in preferred orientation, while the film grown at 600 degrees C was composed of a mixture of the rutile and anatase phases of TiO(2) with the ratio of these phases altering with position on the substrate. The results of physical property measurements and electron microscopy carried out on the films are also reported, conducted at locations identified by the X-ray diffraction mapping procedure as having different compositions, and hence different physical responses. We found that the photocatalytic activity and hydrophobicity were dependent on the rutile:anatase ratio at any given location on the film.     

Photoassisted synthesis of CdSe and core-shell CdSe/CdS quantum dots

This paper describes the synthesis of core-shell CdSe/CdS quantum dots (QDs) in aqueous solution by a simple photoassisted method. CdSe was prepared from cadmium nitrate and 1,1-dimethylselenourea precursors under illumination for up to 3 h using a pulsed Nd:YAG laser at 532 nm. The effects that the temperature and the laser irradiation process have on the synthesis of CdSe were monitored by a series of experiments using the precursors at a Cd:Se concentration ratio of 4. Upon increasing the temperature (80-140 degrees C), the size of the CdSe QDs increases and the time required for reaching a maximum photoluminescence (PL) is shortened. Although the as-prepared CdSe QDs possess greater quantum yields (up to 0.072%) compared to those obtained by microwave heating (0.016%), they still fluoresce only weakly. After passivation of CdSe (prepared at 80 degrees C) by CdS using thioacetamide as the S source (Se:S concentration ratio of 1) at 80 degrees C for 24 h, the quantum yield of the core-shell CdSe/CdS QDs at 603 nm is 2.4%. Under UV irradiation of CdSe/CdS for 24 h using a 100-W Hg-Xe lamp, the maximum quantum yield of the stable QDs is 60% at 589 nm. A small bandwidth (W1/2 < 35 nm) indicates the narrow size distribution of the as-prepared core-shell CdSe/CdS QDs. This simple photoassisted method also allows the preparation of differently sized (3.7-6.3-nm diameters) core-shell CdSe/CdS QDs that emit in a wide range (from green to red) when excited at 480 nm.     

The Effect of Alcohol Solvents on the Porosity and Phase Composition of Titania

Bimodally porous titania powders were made by hydrolysis of titanium tetraisopropoxide (TTIP) dissolved in various alcohols (methanol, ethanol, isopropanol, and sec-butanol). The specific surface area (SSA) of the powders dried at 150 degrees C ranged from 332 to 624 m(2)/g as determined by nitrogen adsorption. At excess alcohol concentration, the SSA of the dried powders decreased in the order of sec-butanol, iso-propanol, ethanol, and methanol at a constant alcohol/TTIP molar ratio. The pore size distribution was bimodal with fine intraparticle pore diameters at 1-6 nm and larger interparticle pore diameters at 30-120 nm as determined by nitrogen adsorption isotherms. The average intraparticle pore diameter decreased with increasing alcohol concentration for methanol and ethanol, while it was rather constant at 3.3 nm, irrespective of alcohol concentration for iso-propanol and sec-butanol. The evolution of particle phase composition was determined by X-ray diffraction ranging from amorphous to crystalline anatase and rutile largely proportional to the calcination temperature and to a lesser extent on the type and concentration of alcohols. Copyright 2000 Academic Press.