ZrO2纳米流体的对流换热系数测定及机理浅析

建立了测量圆管内纳米流体流动与传热性能的实验系统,测量了不同粒子浓度的ZrO2/水纳米流体在雷诺数为3 000～18 000范围内的管内对流换热系数以及不同位置处纳米流体对流换热系数的变化情况.实验结果显示,在液体中添加纳米粒子显著增大了液体的管内对流换热系数,例如,在相同雷诺数时,与纯水相比,如果纳米粒子的质量浓度从1.6%增大到4.1%,则纳米流体的对流换热系数增加的比例从1.09增大到1.2.此外,从颗粒的浓度、粒径两方面分析纳米流体强化传热的机理.     

The effect of velocity and dimension of solid nanoparticles on heat transfer in non-Newtonian nanofluid

In this investigation, the behavior of non-Newtonian nanofluid hydrodynamic and heat transfer are simulated. In this study, we numerically simulated a laminar forced non-Newtonian nanofluid flow containing a 0.5 wt% carboxy methyl cellulose (CMC) solutionin water as the base fluid with alumina at volume fractions of 0.5 and 1.5 as the solid nanoparticle. Numerical solution was modelled in Cartesian coordinate system in a two-dimensional microchannel in Reynolds number range of 10≤Re≤1000. The analyzed geometrical space here was a rectangular part of whose upper and bottom walls was influenced by a constant temperature. The effect of volume fraction of the nanoparticles, Reynolds number and non-Newtonian nanofluids was studied. In this research, the changes pressure drop, the Nusselt number, dimensionless temperature and heat transfer coefficient, caused by the motion of non-Newtonian nanofluids are described. The results indicated that the increase of the volume fraction of the solid nanoparticles and a reduction in the diameter of the nanoparticles would improve heat transfer which is more significant in Reynolds number. The results of the introduced parameters in the form of graphs drawing and for different parameters are compared.     

Intriguingly high convective heat transfer enhancement of nanofluid coolants in laminar flows

We reported on investigation of the convective heat transfer enhancement of nanofluids as coolants in laminar flows inside a circular copper tube with constant wall temperature. Nanofluids containing Al₂O₃, ZnO, TiO₂, and MgO nanoparticles were prepared with a mixture of 55 vol.% distilled water and 45 vol.% ethylene glycol as base fluid. It was found that the heat transfer behaviors of the nanofluids were highly depended on the volume fraction, average size, species of the suspended nanoparticles and the flow conditions. MgO, Al₂O₃, and ZnO nanofluids exhibited superior enhancements of heat transfer coefficient, with the highest enhancement up to 252% at a Reynolds number of 1000 for MgO nanofluid. Our results demonstrated that these oxide nanofluids might be promising alternatives for conventional coolants.     

Physics and mechanics of heat exchange processes in nanofluid flows

Nanofluids present a new type of dispersed fluids consisting of a carrier fluid and solid nanoparticles. Unusual properties of nanofluids, particularly high thermal conductivity, make them eminently suitable for many thermophysical applications, e.g., for cooling of equipment, designing of new heat energy transportation and production systems and so on. This requires a systematic study of heat exchange properties of nanofluids. The present paper contains the measurement results for the heat transfer coefficient of the laminar and turbulent flow of nanofluids on the basis of distilled water with silica, alumina and copper oxide particles in a minichannel with circular cross section. The maximum volume concentration of particles did not exceed 2%. The dependence of the heat transfer coefficient on the concentration and size of nanoparticles was studied. It is shown that the use of nanofluids allows a significant increase in the heat transfer coefficient as compared to that for water. However, the obtained result strongly depends on the regime of flow. The excess of the heat transfer coefficient in the laminar flow is only due to an increase in the thermal conductivity coefficient of nanofluid, while in the turbulent flow the obtained effect is due to the ratio between the viscosity and thermal conductivity of nanofluid. The viscosity and thermal conductivity of nanofluids depend on the volume concentration of nanoparticles as well as on their size and material and are not described by classical theories. That is why the literature data are diverse and contradictory; they do not actually take into account the influence of the mentioned factors (size and material of nanoparticles). It has been shown experimentally and by a molecular dynamics method that the nanofluid viscosity increases while the thermal conductivity decreases with the decreasing dispersed particle size. It is found experimentally for the first time that the nanofluid viscosity coefficient depends on the particle material. The higher is the density of particles, the higher is the thermal conductivity coefficient of nanofluid.     

纳米流体研究的新动向

纳米流体近年来成为多个领域内的研究热点，特别是在流体物性测试、机理分析及新的应用上均取得长足进展．文章以该方向上最新完成的几类富有启发性的工作，如纳米流体热管、基于纳米液滴的纳米流体、纳米金属流体及借助于纳米颗粒控制纳米流体流动等进展予以剖析，归纳出了其中有待解决的一些重要科学问题，并指出一些可能的新应用。     

Experimental evaluation of friction factor and heat transfer enhancement of twisted tape inserts using TiO<Subscript>2</Subscript>–water nanofluids

This paper studies the experimental evaluation of TiO₂ nanofluids in enhancing the heat transfer rate and friction factor on a micro-finned tube fitted with twisted tape inserts. Results show that the enhancement in heat transfer and pumping power completely depends on the concentration ratio of nanoparticles, pitch ratio and the type of pitch. Comparisons were made with the previous study with different operating parameters such as twist ratio and twist type. Viscosity of nanofluid increases with an increase in the concentration, which leads to increased pressure drop and pumping power. For the Reynolds number (Re = 4000), the maximum performance ratio was found as 2.1, 2, for concentration of 0.1 and 0.05, respectively. The addition of microfin arrangement inside the circular tube enhanced the performance ratio with minimum concentration of TiO₂ nanofluid.     

几种氧化物纳米流体强化传热性能研究

以水/乙二醇混合液为基液,加入A12O3,MgO和ZnO纳米颗粒配制得到纳米流体.在自制对流传热性能测试平台上进行基液及纳米流体传热性能的测试.结果表明:同基液相比,随流体流速增大,A12O3纳米流体的传热系数变化不明显,MgO和ZnO纳米流体的传热系数均有提高.层流状态下,随雷诺数增大,三种纳米流体的传热系数都不断增...     

Comparative study on thermal performance of helical screw tape inserts in laminar flow using Al2O3/water and CuO/water nanofluids

This paper presents a comparison of thermal performance of helical screw tape inserts in laminar flow of Al₂O₃/water and CuO/water nanofluids through a straight circular duct with constant heat flux boundary condition. The helical screw tape inserts with twist ratios Y = 1.78, 2.44 and 3 were used in the experimental study using 0.1% volume concentration Al₂O₃/water and CuO/water nanofluids. Nanofluids with required volume concentration of 0.1% were prepared by dispersing specified amounts of Al₂O₃ and CuO nanoparticles in deionised water. The performance analysis of helical screw tape inserts in laminar flow of Al₂O₃/water and CuO/water nanofluids is done by evaluating thermal performance factor for constant pumping power condition. Thermal performance factor of helical screw tape inserts using CuO/water nanofluid is found to be higher when compared with the corresponding value using Al₂O₃/water. Therefore, the helical screw tape inserts show better thermal performance when used with CuO/water nanofluid than with Al₂O₃/water nanofluid.     

Overview of Hybrid Nanofluids Development and Benefits

Conventional fluids have poor heat transfer properties, but their vast applications in power generation, chemical processes, heating and cooling processes, electronics and other microsized applications make the reprocessing of those thermofluids to have better heat transfer properties quite essential. Recently, it has been shown that the addition of solid nanoparticles to various fluids can increase the thermal conductivity and can influence the viscosity of the suspensions by tens of percent. Thermophysical properties of nanofluids were shown dependent on the particle material, shape, size, concentration, the type of the base fluid, and other additives. In spite of some inconsistency in the reported results and insufficient understanding of the mechanism of the heat transfer in nanofluids, it has been emerged as a promising heat transfer fluid. In the continuation of nanofluids research, the researchers have also tried to use hybrid nanofluid recently, which is engineered by suspending dissimilar nanoparticles either in mixture or composite form. The idea of using hybrid nanofluids is to further improve the heat transfer and pressure drop characteristics by trade-off between advantages and disadvantages of individual suspension, attributed to good aspect ratio, better thermal network and synergistic effect of nanomaterials. As a conclusion, the hybrid nanofluids containing composite nanoparticles yield significant enhancement of thermal conductivity. However, the long-term stability, production process, selection of suitable nanomaterials combination to get synergistic effect and cost of nanofluids may be major challenges behind the practical applications.     

抛物槽式太阳能集热器内合成油基纳米流体传热特性的数值模拟

对Al₂O₃-合成油纳米流体在槽式太阳能集热管内的传热特性进行流体动力学数值模拟,重点考察纳米流体导热系数模型的影响。通过与管内Nusselt数半经验模型的预测结果对比,表明使用考虑布朗运动的纳米流体导热系数模型可较好地预测集热管内传热特性。研究表明纳米颗粒与流体基液的相对运动具有促进集热管内传热的作用。最后,定量研究纳米颗粒添加量对提高基础流体平均传热系数的影响,显示纳米流体在太阳能集热器中具有巨大应用潜力。     

基于晶格-Boltzmann方法的纳米流体流动和传热模型

纳米流体是由流体与纳米粒子组成的悬浮体.悬浮在流体中的纳米粒子会受到运动阻力、布朗力、扩散力和重力等作用力的影响,因而其运动规律极其复杂.本文运用晶格-Boltzmann(LB)方法,建立纳米流体流动和传热模型模型,对纳米流体的流型结构和温度场进行了模拟和分析.     

Ultrasonically tuned surface tension and nano-film formation of aqueous ZnO nanofluids

Nanofluids’ thermophysical properties and heat transfer performance has been investigated for many years, while research on their surface tension (ST) and wetting behavior is very limited. To assess nanofluids potential as industrial products, a complete picture is required to prove their performance in a specific application. Boiling heat transfer, microfluidics and drug development are among the applications where ST is a variable. ST of water-based ZnO nanofluids were measured in the presence and absence of direct ultrasonication. The experiments covered variation of ST with ZnO concentration (0.05–0.4 vol%), ultrasonication amplitude (40% and 100%) and duration. To the best of the authors’ knowledge, this is the first report of ST– ultrasonication process relation for a nanofluid. Results showed that after direct ultrasonication, nanofluids ST is strongly affected by the temperature raise, and in those cases relative ST may provide a clearer picture. A nano-film over individual and agglomerated nanoparticles spotted via TEM imaging was affected from the ultrasonication. Such a nano-film can play a key role in the anomalous thermal transport and wettability of nanofluids. Statistical analyses revealed that changes in ultrasonication amplitude resulted in a statistically significance difference on nanofluid ST and relative ST. Changes in nanoparticle concentration caused a significant difference on the nanofluid ST while the difference in relative ST was insignificant. Variation of ultrasonication duration caused significant variations on the relative ST while the difference in nanofluid ST was not significant. This work highlights that based on specific applications ST and other related features of any nanofluid can be adjusted employing proper ultrasonication conditions.     

纳米流体对流换热系数增大机理

纳米流体流动换热能力优于传统流体介质.研究了纳米流体热物性的提升和热散射对其对流换热系数的影响.结果表明,纳米颗粒的加入,优化了介质的热物性,增大了导热系数,强化了纳米流体内颗粒、流体以及流道管壁碰撞和相互作用,同时加强了流体的混合脉动和湍流,从而增大了对流换热系数. 关键词： 纳米流体 换热系数 热散射     

Heat transfer enhancement by application of nano-powder

In this investigation, laminar flow heat transfer enhancement in circular tube utilizing different nanofluids including Al₂O₃ (20 nm), CuO (50 nm), and Cu (25 nm) nanoparticles in water was studied. Constant wall temperature was used as thermal boundary condition. The results indicate enhancement of heat transfer with increasing nanoparticle concentrations, but an optimum concentration for each nanofluid suspension can be found. Based on the experimental results, metallic nanoparticles show better enhancement of heat transfer coefficient in comparison with oxide particles. The promotions of heat transfer due to utilizing nanoparticles are higher than the theoretical correlation prediction.     

Thermal characterization of a nanofluid comprising nanocrystalline ZrO2 dispersed in water and ethylene glycol

Nanofluids, comprising Y₂O₃-stabilized (partially; 3?mol%) ZrO₂ nanoparticles (up to 2?vol%) dispersed in water and ethylene glycol, were developed. A suitable surfactant and stirring routine ensured uniformity and stability of dispersion. Thermal conductivity ratio of the nanofluids, measured using an indigenously developed thermal comparator device, showed a significant increase of up to 100% with only 1.5?vol% nanoparticles. Furthermore, it was analytically shown that shape factor and aspect ratio significantly influence the effective thermal conductivity ratio of nanofluids with comparable vol% nanoparticles. The study demonstrated that a nanofluid of nano-ZrO₂ dispersed in water and ethylene glycol could be usefully applied in closed-loop single-phase heat transfer conditions, such as in refrigerators or microchannels.     

Convective Heat Transfer of a Cu/Water Nanofluid Flowing Through a Circular Tube

Abstract

Fluids in which nanometer-sized solid particles are suspended are called nanofluids. These fluids can be employed to increase the heat transfer rate in various applications. In this study, the convective heat transfer for Cu/water nanofluid through a circular tube was experimentally investigated. The flow was laminar, and constant wall temperature was used as thermal boundary condition. The Nusselt number of nanofluids for different nanoparticle concentrations, as well as various Peclet numbers, was obtained. Also, the rheological properties of the nanofluid for different volume fractions of nanoparticles were measured and compared with theoretical models. The results show that the heat transfer coefficient is enhanced by increasing the nanoparticle concentrations as well as the Peclet number.     

纳米流体对流换热的实验研究

建立了测量纳米流体对流换热系数的实验系统,测量了不同粒子体积份额的水-Cu纳米流体在层流与湍流状态下的管内对流换热系数,实验结果表明,在液体中添加纳米粒子增大了液体的管内对流换热系数,粒子的体积份额是影响纳米流体对流换热系数的因素之一。综合考虑影响纳米流体对流换热的多种因素,提出了计算纳米流体对流换热系数的关联式。     

小通道扁管内纳米流体流动与传热特性

建立了测量小通道扁管内纳米流体流动与对流换热性能的实验系统,测量了不同粒子体积份额的水-Cu纳米 流体的管内对流换热系数和摩擦阻力系数,实验结果表明,在相同雷诺数条件下,小通道扁管内纳米流体的对流换热系数 大于纯液体,且随粒子的体积份额的增加而增大,而纳米流体的阻力系数并未明显增大。     

Heat Transfer and Pressure Drop Characteristics of Graphene Oxide/Water Nanofluid in a Circular Tube Fitted with Wire Coil Insert

In this work, heat transfer and pressure drop characteristics of graphene oxide/water nanofluid flow through a circular tube having a wire coil insert were studied. The required graphene oxide was synthesized via the Hummer method and characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (SRD), and scanning electron microscope (SEM) methods. Dispersing graphene oxide in the water, nanofluids with 0.02, 0.07, and 0.12% volume fraction were prepared. An experimental set-up was designed and made to investigate the heat transfer performance and pressure loss of nanofluids. All experiments were carried out in the constant heat flux at tube wall conditions. The volumetric flow rates of the nanofluid were adjusted at 6, 8, and 10 L/min. Thermal conductivity, specific heat, density, and viscosity as thermophysical properties of the nanofluid were calculated using graphene oxide and water properties at the average temperature via appropriate relations. These properties were applied to calculate the convective heat transfer coefficient, Nusselt number, and friction factors for each experiment. Finally, the constant and exponents of Duangthongsuk and Wongwises's correlations for Nusselt number and friction factor were corrected by experimental results. The achieved experimental data have shown good agreement with those predicted. The results have shown that 0.12 vol% of graphene oxide in the water can enhance convective heat transfer coefficient by about 77%. As a result, it can be concluded that the graphene oxide/water can be used in the heat transfer devices to achieve more efficiency.     

Performance of thermoelectric generator with graphene nanofluid cooling

Improvement of the heat transfer of the cold side is one of the approaches to enhance the performance of TEG systems.As a new type of heat transfer media, nanofluids can enhance the heat transfer performance of working liquid significantly.Based on a three-dimensional and steady-state numerical model,the heat transfer and thermoelectric conversion properties of TEG systems were studied. Graphene anoplatelet aqueous nanofluids were used as the coolants for the cold side of the TEG system to improve the heat transfer capacity of the cold side. The results showed that the heat absorbed by the hot side, voltage, output power, and conversion efficiency of the TEG system were increased greatly by the nanofluid coolants.The output power and the conversion efficiency using 0.1-wt% graphene nanoplatelet aqueous nanofluid as the coolant are enhanced by 26.39% and 14.74%, respectively.