Simultaneous Determination of Levomepromazine Hydrochloride and Its Sulfoxide by UV‐Derivative Spectrophotometry and Bivariate Calibration Method

Abstract

Two spectrophotometric methods are proposed for the simultaneous quantification of levomepromazine hydrochloride (LV) and its main degradation product levomepromazine sulfoxide (LV‐SO). One of them is based on the first order derivative spectra generated by the Savitzky‐Golay algorithm (third‐order polynomial degree, Δλ=10 nm). Determination of levomepromazine hydrochloride and its sulfoxide was realized by measurements of amplitudes of derivative spectra at 332 nm and 278 nm, respectively. The Beer law was obeyed in the concentration range 1.5–50 µg/mL for LV and 2.5–50 µg/mL for LV‐SO. The second of the proposed methods utilized the bivariate calibration algorithm. The determination was performed at 302 nm for levomepromazine and at 334 nm for sulfoxide. The elaborated methods allowed determination of LV in the concentration range 1.0–25 µg/mL while LV‐SO was determined in the concentration range 2.0–50 µg/mL.     

The Use of Internal Standard Method for Dertvative-Spectrophotometric Determination of Chlorpromazine Hydrochloride

ABSTRACT

The use of 1, 10-phenantroline as internal standard (IS) is proposed for spectrophotometric determination of chlorpromazine hydrochloride in pharmaceutical formulations. The spectra of both compounds: analyte and internal standard are partially overlapped, so the Savitzky-Golay alghoritm was used to obtain separated signals of analyte and IS. The best parameters to generate the second-derivative spectra were: ∠λ = 10 nm (5 experimental points) and second polynomial degree. For quantification of chlorpromazine in pharmaceuticals, the zero-crossing technique was used. The values of the second-derivative peaks were measured for chlorpromazine at 256 nm and at 236 nm for IS. Analytical characteristic for proposed method was evaluated (r²=0.9990, detection limit=3.97 ng/ml). The obtained analytical results were in good agreement with results obtained using the UV-spectrophotometric Blazek method.     

Validated stability-indicating methods for the determination of nizatidine in the presence of its sulfoxide derivative

Four new selective, precise, and accurate methods are described for the determination of nizatidine (NIZ) in the presence of its sulfoxide derivative in both the raw material and pharmaceutical preparations. Method A is based on zero-order (0D), first-derivative (1D), and second-derivative (2D) spectrophotometric measurement of NIZ in aqueous solution at the zero-crossing point of its sulfoxide derivative (at 314, 295-334, and 318-348 nm, respectively). Method B is a 1DD spectrophotometric method based on the simultaneous use of the first derivative of the ratio spectra and the measurement of peak amplitude at 297 nm. Method C uses a solvent-induced derivative-difference spectrophotometry with deltaD1 measurement from peak to peak at 315-345 nm. Method D involves quantitative densitometric evaluation of a mixture of the drug and its sulfoxide derivative after separation by high-performance thin-layer chromatography on silica gel plates with chloroform-methanol (9 + 1, v/v) as the mobile phase; Rf values for NIZ and its sulfoxide derivative were 0.4 and 0.2, respectively. The spot was scanned at 254 nm. The first-derivative spectrophotometric method was used to investigate the kinetics of the hydrogen peroxide degradation process at different temperatures. The apparent pseudo-first-order rate constant, half-life, and activation energy were calculated. The results obtained by the proposed methods were analyzed statistically and compared with those obtained by the official method. These methods are suitable as stability-indicating for the determination of NIZ in the presence of its oxidation-induced degradation product (sulfoxide derivative) either in the bulk powder or in pharmaceutical preparations.     

An application of UV-derivative spectrophotometry and bivariate calibration algorithm for study of photostability of levomepromazine hydrochloride

Derivative spectrophotometry and bivariate calibration algorithm were used for study of run of photooxidation of levomepromazine hydrochloride (LV). The actual concentrations of LV and its main degradation product levomepromazine sulphoxide (LV-SO) were calculated using data provided by applied methods. The direct reading of absorbance values at 302 nm and 334 nm were employed for quantification of LV and LV-SO, respectively, in the case of bivariate method. The derivative spectrophotometric method is based on transformation of zero-order spectra into first derivative. The values of first derivative at 334 nm were used for quantification of LV while at 278 nm for assay of LV-SO. The obtained quantitative data were applied for investigation of kinetics of photodegradation of LV.     

Multicomponent analysis: Comparison of various graphical and numerical methods

The performance of several graphical (zero-crossing and derivative quotient spectra with standardized divisor) and numerical methods (MULTIC and PLS) for the resolution of binary and ternary mixtures of species is compared. Numerical methods were found to be specially suited to multicomponent analysis, particularly for mixtures containing more than two analytes with highly overlapped spectra. The results obtained by using the compared methods to analyse various synthetic mixtures of acetylsalicylic acid, caffeine and thiamine were quite consistent and errors in the simultaneous quantification of the analytes amounted to less than 5% in all instances.     

Simultaneous determination of norfloxacin and lomefloxacin in milk by first derivative synchronous fluorescence spectrometry using Al (III) as an enhancer

A novel method for the simultaneous determination of norfloxacin (NFLX) and lomefloxacin (LFLX) in milk samples was developed by using first derivative synchronous fluorimetry. The synchronous fluorescence (Δλ=160 nm) spectra and first derivative synchronous fluorescence spectra of NFLX, LFLX and their mixture were studied. The zero-crossing method was utilized to measure the first derivative value of the derivative spectrum. The zero-crossing points were located at 275.0 nm for NFLX and at 283.8 nm for LFLX, in first derivative synchronous fluorescence spectra. Therefore, 283.8 nm and 275.0 nm were selected for the determination of NFLX and LFLX. The first derivative values varied linearly with the concentrations in the range of 1.68×10(-8)-5.64×10(-6) mol L(-1) for NFLX and 1.89×10(-8)-6.19×10(-6) mol L(-1) for LFLX. The detection limits were 5.03×10(-9) mol L(-1) for NFLX and 7.58×10(-9) mol L(-1) for LFLX. The proposed method is reliable, selective and sensitive, and has been used successfully in the simultaneous determination of NFLX and LFLX in milk samples, whose results were in good agreement with those obtained by HPLC.     

Multi-component kinetic-spectrophotometric analysis. Selection of wavelength and time ranges

An empirical method for the selection of the best wavelength and time ranges which can be used in the quantification of binary mixtures, in a kinetic-spectrophotometric system, is proposed. It is based on finding those ranges which provide the least correlation between the kinetic profiles and the spectra of the products of reaction. The method was applied to the analysis of binary mixtures using simulated data with different rate constant ratios and in the presence of an interference that shows spectral overlap with the analytes. Subsequently, the proposed method was applied to the resolution of dyphylline and proxyphylline mixtures. The system studied was characterized by an elevated similarity in the kinetic behavior of the analytes under pseudo-first-order conditions and an elevated degree of spectral overlap of the products of reaction. In spite of this, satisfactory results were obtained in the quantification of the two analytes. The standard error of prediction (SEP) and the standard deviation between replicates (SDBR) did not show significant differences, being of the order of 4 and of 3% for dyphylline and proxyphylline, respectively.     

A flow-through fluorimetric sensing device for determination of alpha- and beta-naphthol mixtures using a partial least-squares multivariate calibration approach

A single flow-through optosensor spectrofluorimetric system is proposed for the resolution of mixtures of alpha- and beta-naphthol at mug l(-1) levels using a partial least-squares (PLS) calibration approach. The sensor was developed in conjunction with a monochannel flow-injection analysis system with fluorimetric detection using Sephadex QAE A-25 resin as an active sorbent substrate in the flow cell and the second derivative of the native synchronous fluorescence spectra of analytes as analytical signal. In the manifold, the solutions of naphthol (at pH 10.0) were injected in a carrier stream of KCl (0.15 M)/NaOH (10(-2) M). Because of the strong spectral overlap, the mixture could not be resolved by conventional spectrofluorimetry. The non-additive behaviour of the fluorescence signals revealed an interaction in the system, which was not found by working in the solution only (without the sorbent support). This interaction, probably due to the environment of the analytes on the solid phase, made impossible their simultaneous determination. So, the use of synchronous fluorescence spectroscopy or even its derivative signal could not resolve satisfactorily the mixture. The simultaneous determination of both naphthol has been carried out by recording the signal of the second-derivative synchronous fluorescence (Deltalambda=170 nm) spectra between 200 and 450 nm and a PLS multivariate calibration treatment. The optimum number of factors was selected by using the cross-validation method. After validating the proposed method, it was applied to the determination of these compounds in natural waters with different amounts of each chemical.     

A comparative study on various spectrometries with thin layer chromatography for simultaneous analysis of drotaverine and nifuroxazide in capsules

Three spectrophotometric methods including Vierordt's method, derivative, ratio spectra derivative, and thin layer chromatography (TLC)-UV densitometric method were developed for simultaneous determination of drotaverine HCl (DRT) and nifuroxazide (NIF) in presence of its impurity, 4-hydroxybenzohydrazide (4-HBH). In Vierordt's method, (E(1 cm)(1%)) values were calculated at 227 and 368 nm in the zero-order spectra of DRT and NIF. By derivative spectrophotometry, the zero-crossing method, drotaverine HCl was determined using the second derivative at 245 nm and the third derivative at 238 nm, while nifuroxazide was determined using the first derivative at 399 nm and the second derivative at 411 nm. The ratio spectra derivative spectrophotometry is basedon the measure of the amplitude at 459 nm for DRT and at 416 nm for NIF in the first derivative of the ratio spectra. Calibration graphs of the three spectrophotometric methods were plotted in the range 1-10 mug/ml of DRT and 2-20 mug/ml of NIF. TLC-UV densitometric method was achieved on silica gel plates using ethyl acetate : methanol : ammonia 33% (10 : 1 : 0.1 v/v/v) as the mobile phase. The Rf values were 0.74, 0.50, 0.30+/-0.01 for DRT, NIF and 4-HBH, respectively. On the fluorescent plates, the spots were located by fluorescence quenching and the densitometrical area were measured at 308 and 287 nm with linear range 0.2-4 mug/spot and 0.6-12 mug/spot for DRT and NIF, respectively. The proposed methods have been successfully applied to the commercial pharmaceutical formulation without any interference of excipients. Mean recoveries, relative standard deviations and the results of the proposed methods were compared with those obtained by applying the alternate methods.     

Second derivative spectrophotometric determination of partition coefficients of phenothiazine derivatives between human erythrocyte ghost membranes and water

The absorption spectra of six phenothiazine derivatives, chlorpromazine, triflupromazine, promazine, promethazine, trifluoperazine and prochlorperazine, measured in the solutions containing various amounts of human erythrocyte ghosts (HEG) showed bathocromic shifts according to the amount of HEG. Due to the strong background signals caused by HEG, the baseline compensation was incomplete, even though the sample and the reference solutions contained the same amount of HEG, hence further spectral information could not be obtained. The second derivative spectra of these absorption spectra clearly showed the derivative isosbestic points, indicating that the residual background signal effects were entirely eliminated. The derivative intensity differences of the phenothiazines (ΔD values) before and after the addition of HEG were measured at a specific wavelength. Using the ΔD values, the partition coefficients (K_p) of these drugs were calculated and obtained with R.S.D. of below 10 %. The fractions of partitioned phenothiazines calculated from the K_p values agreed well with the experimental values. The results indicate that the derivative method can be applicable to the determination of partition coefficients of drugs to HEG without any separation procedures.     

Simultaneous Determination of Caffeine and Meclizine Dihydrochloride in Sugar-Coated Tablets

Abstract

In this study, simultaneous determination of caffeine and meclizine dihydrochloride in their binary mixture was conducted by two spectrophotometric methods. In the first method, derivative spectrophotometry, the quantification of caffeine and meclizine dihydrochloride was performed by reading the dA/dλ values at 286.2 nm and 243.4 nm respectively in the first derivative spectra of their mixture in methanol. The relative standard deviation of the method was 0.54% for caffeine and 0.67% for meclizine dihydrochloride. In the second, selective precipitation + derivative spectrophotometry, determination of meclizine dihydrochloride was carried out by precipitation with potassium ferricyanide at pH 2 selectively, then measuring the absorbance of its solution in methanol at 420.8 nm, and determination of caffeine was succeeded by reading the dA/dλ values at 260.6 nm in the first derivative spectra of the remaining solution after precipitation. Relative standard deviation of the method was found to be 0.56% for caffeine and 1.85% for meclizine dihydrochloride. These two methods were applied successfully to a sugar-coated tablet containing these drugs.     

FREE RADICAL PRODUCTION BY CHLORPROMAZINE SULFOXIDE, AN ESR SPIN-TRAPPING AND FLASH PHOTOLYSIS STUDY

Abstract— Using the spin-trapping technique we have investigated the photolysis of chlorpromazine sulfoxide and promazine sulfoxide. Photolysis of these sulfoxides in aqueous solution resulted in a species which is capable of oxidizing ascorbate, cysteine, glutathione, NADH, and azide by one electron, in addition to extracting hydrogen atoms from ethyl alcohol and dimethyl sulfoxide. These oxidations were not dependent on the presence of dissolved oxygen. The oxidizing species is proposed to be the hydroxyl free radical arising from the homolytic cleavage of the S-O bond of the sulfoxide. Flash photolysis of the chlorpromazine and promazine sulfoxides demonstrated the formation of cation radicals consistent with the loss of the hydroxyl radical from the sulfoxides. In addition we present a simple direct method for the quantitative synthesis of promazine and chlorpromazine sulfoxides from the parent promazine derivatives.     

Derivative spectrophotometric determination of holmium in rare earth mixtures with 2-(diphenylacetyl)indan-1,3-dione and octylphenyl poly(ethyleneglycol) ether

The zero-order and second-order derivative absorption spectra of the system of holmium with 2-(diphenylacetyl) indan-1, 3-dione and octylphenyl poly(ethyleneglycol) ether have been determined by derivative spectrophotometry. The molar absorptivity of absorption spectra and the derivative spectra are calculated respectively. The absorbances at the absorption maxima for the holmium complex are 48.5 (at 450 nm) and 14.5 (at 460 nm) times greater than for the corresponding chloride. The derivative spectra have been used to eliminate the interference of other lanthanides, and the sensitivity is again increased by a factor of about 5. The calibration graph is linear up to 25 g/ml of holmium. The detection limit, obtained from the sensitivity of the calibration graph and for 3S _b (S_b = standard deviation of a blank without holmium,n = 11), was 0.37 g/ml of holmium. The quantification limit (10S_b was 1.2 g/ml. The method has been applied successfully to synthetic and reference samples of rare earths.     

Fluorescence spectrometry for quantitative characterization of cobalt(II) complexation by Leonardite humic acid

Quenching of the fluorescence of a Leonardite humic acid by Co(II) has been studied at different pH. The interaction was monitored by emission fluorescence and by synchronous fluorescence with two different offsets (deltalambda=20 and 80 nm). It was found that synchronous fluorescence performed with the smaller offset resolves the individual components of the heterogeneous material better than emission or synchronous fluorescence performed with the larger offset. Enhancement of the signal induced by Cobalt(II) complexation resulted in more complex behavior for measurements performed by synchronous fluorescence with an offset of 20 nm, however. The quenching profiles obtained for pH 5.0, 6.0, and 7.0 ([KNO(3)]=0.1 mol L(-1); [LHA]=3.3 mg(C) L(-1); [Co(II)]=1.0 x 10(-6)-1.6 x 10 (-3) mol L(-1)) by emission and synchronous (deltalambda=80 nm) fluorescence were analyzed by two methods: 1. a non-linear least-squares procedure that leads to conditional constants; and 2. a pH-dependent discrete logK spectrum model that leads to stability constants. The first method resulted in poor fitting and unreasonable values for maximum capacities. The second procedure resulted in smooth fitting that accounted well for the pH changes when results for pH 6.0 and 5.0 were predicted by use of the four values of logK(Co)(i) (4.31, 3.76, 7.32, and 7.67 corresponding to the four sites (i) of the respective pKa(i) values 4, 6, 8, and 10) calculated at pH 7.0 for the equilibrium     

Derivative and Derivative Ratio Spectrophotometric Analysis of Antihypertensive Ternary Mixture of Amiloride Hydrochloride,Hydrochlorothiazide and Timolol Maleate

Two simple, rapid and reliable spectrophotometric methods are described for the resolution of the three‐component mixture of amiloride hydrochloride (AMD), hydrochlorothiazide (HCT) and timolol maleate (TIM). The first method involves the use of derivative spectrophotometry with the zero‐crossing technique where AMD was easily determined using its ⁰D and ¹D(Δλ = 6) amplitudes at 365 and 385 nm, respectively, while HCT and TIM were determined by measuring the ³D(Δλ = 6) amplitude at 265 nm and the ¹D(Δλ = 8) amplitude at 315.4 nm, respectively. The second method involves the application of the ratio‐spectra zero‐crossing first and second derivative spectrophotometry where two points have been used for the quantification of each compound. For the determination of AMD, HCT was used as divisor and the ¹DD (Δλ = 4) and ²DD (Δλ = 6) values at 299.4 and 311 nm, respectively, were plotted against AMD concentration; while — by using TIM as divisor — the ²DD (Δλ = 6) amplitudes at 264.2 and 290 nm were found to be proportional to HCT concentration. TIM was assayed in the mixture using its ¹DD (Δλ = 6) amplitudes at 289.8 nm (Divisor was AMD) and 314.8 nm (Divisor was HCT). Synthetic mixtures of different proportions and laboratory‐made tablets were assayed by the proposed methods and the results revealed good accuracy and repeatability of the developed methods.     

Enhancement of Fluorescence Intensity of Tramadol and Its Main Metabolites in LC Using Pre-Column Derivatization with 9-Fluorenylmethyl Chloroformate

Tramadol was found to exhibit weak fluorescence with a maximum emission at 300 nm when excited at 200 nm. Also, fluorescence spectra of the drug and its two main metabolites, O-desmethyltramadol and N-desmethyltramadol are not practically identical. Thus low and different sensitivities have been reported for the drug and its metabolites in previously published work. In the present method using 9-fluorenylmethyl chloroformate (FMOC-Cl) as labeling agent, equal and magnified fluorescence intensity were obtained for the analytes. The drug, its metabolites and an internal standard (oseltamivir phosphate) were extracted from serum by dichloromethane. Pre-column derivatization of the analytes was achieved using FMOC-Cl in the presence of borate buffer (0.1 M, pH 7.5). Liquid chromatography with a mobile phase consisting of a mixture of 0.05 M phosphate buffer containing triethylamine (2 ml L^?1; pH = 3.0) and methanol (54:46; v/v) and a Shimpack CLC-ODS column were used for analytical separation of the analytes. The fluorescence of the column effluent was monitored at an excitation and emission wavelengths of 265 and 315 nm, respectively. The analytical method was linear over the concentration range of 1.0–1,280 ng mL^?1 of the parent drug and its metabolites and limit of quantification of 1.0 ng mL^?1 was obtained for the analytes using 10 μL injection. The method validation was studied and the validated method applied in a bioequivalence study of 2 different tramadol preparations in 24 healthy volunteers.     

A new spectrophotometric method for quantitative multicomponent analysis resolution of mixtures of salicylic and salicyluric acids

A new spectrophotometric method for resolving binary mixtures is proposed. The method is based on use of the first derivative of the ratios of spectra. The absorption spectrum of the mixture is obtained and the amplitudes at appropriate wavelengths are divided by the corresponding amplitudes in the absorption spectrum of a standard solution of one of the components, and the first derivative of the ratio spectrum is obtained. The concentration of the other component is then determined from a calibration graph. The method has been applied for resolving binary mixtures of salicylic and salicyluric acids. Calibration graphs for 2.6-52 ppm salicylic acid and for 2.1-42 ppm salicyluric acid were established by measuring the analytical signals at the maximum at 241.5 nm (for salicylic acid) and from the peak at 258 nm to the trough at 247 nm (for salicyluric acid) in the first derivative ratio spectra.     

Simultaneous Determination of Cilazapril and Hydrochlorothiazide in Tablets by Spectrophotometric Methods

Abstract

In this study, two new spectrophotometric methods were used for the simultaneous determination of cilazapril and hydrochlorothiazide in their binary mixture. In the first method, derivative spectrophotometry, dA/dδ values were measured at 242.8 nm and 282.8 nm for cilazapril and hydrochlorothiazide, respectively, in the first derivative spectra of their combination. The relative standard deviation of the method was found to be 0.77% for cilazapril and 0.24% for hydrochlorothiazide. In the second, the absorbancy ratio method, the quantification of cilazapril and hydrochlorothiazide was performed by using the absorbances read at 210.4 nm. 250.2 nm and 270.6 nm in the zero-order spectra of their mixture; relative standard deviations of the method were found to be 1.26 % and 0.81 % for cilazapril and hydrochlorothiazide, respectively. These two methods have been successfully applied to a tablet containing these drugs.     

反相银化高效液相色谱法测定银杏叶中银杏酚酸(英文)

 建立了反相银化高效液相色谱测定银杏叶中银杏酚酸含量的分析方法。在样品的浸提液中加入少量酸性盐溶液和吸附剂后 ,用一步反萃取法净化样品 ,有机相浓缩后供HPLC分析。流动相 :V(甲醇 )∶V(体积分数为 5 %的乙酸水溶液 ) =90∶10 ,其中银离子浓度 0 0 3mol·L-1,紫外检测波长 310nm。结果表明 4种银杏酚酸之间达到基线分离 ,该方法平均回收率为97 3% ,相对标准偏差 1 6 % ,最低检测量 0 0 2 6 μg ,可有效地用于银杏叶及其提取物中银杏酚酸的定量分析。     

Spectrophotometric and spectrodensitometric determination of paracetamol and drotaverine HCl in combination

Thin-layer chromatography, first derivative, ratio spectra derivative spectrophotometry and Vierordt's method have been developed for the simultaneous determination of paracetamol and drotaverine HCl. TLC densitometric method depends on the difference in Rf values using ethyl acetate:methanol:ammonia (100:1:5 v/v/v) as a mobile phase. The spots of the two drugs were scanned at 249 and 308 nm over concentration ranges of 60-1200 microg/ml and 20-400 microg/ml with mean percentage recovery 100.11%+/-1.91 and 100.15%+/-1.87, respectively. The first derivative spectrophotometric method deals with the measurements at zero-crossing points 259 and 325 nm with mean percentage recovery 99.25%+/-1.08 and 99.45%+/-1.14, respectively. The ratio spectra first derivative technique was used at 246 and 305 nm with mean percentage recovery 99.75%+/-1.93 and 99.08%+/-1.22, respectively. Beer's law for first derivative and ratio spectra derivative methods was obeyed in the concentration range 0.8-12.8 and 0.4-6.4 microg/ml of paracetamol and drotaverine HCl, respectively. Vierordt's method was applied to over come the overlapping of paracetamol and drotaverine HCl in zero-order spectra in concentration range 2-26 and 2-40 microg/ml respectively. The suggested methods were successfully applied for the analysis of the two drugs in laboratory prepared mixtures and their pharmaceutical formulation. The validity of the methods was assessed by applying the standard addition technique. The obtained results were statistically agreed with those obtained by the reported method.