Wavelength Switching of a Fabry-Perot Semiconductor Laser by Optical Input Pulses

Wavelength switchings of a Fabry-Perot semiconductor laser are experimentally demonstrated by applying externally optical input pulses detuned from a cavity-resonant wavelength of the semiconductor laser with a constant injection current. The wavelength region of optical switching ranges from less than 0.1 nm to several nm over gain spectrum, being locked to the wavelength of optical inputs. These behaviors are based on multistability and multi-split branches in the optical output versus detuned optical input characteristics, caused by the carrier-induced refractive index change accompanied by optical injections. The experimental results are believed to be useful for wavelength division multiplexing and exchange in optical communication.     

Switching of a Semiconductor Laser with Multi-Detuned Optical Inputs by Controlling Injection Current

The multistability of a Fabry-Perot semiconductor diode laser for an injection current is presented when multi-optical inputs detuned from the cavity-resonant wavelength of a semiconductor laser are injected. m+1 Multi-stable states are shown to be produced in the optical output versus injection current characteristics for m detuned optical inputs. It is shown that optical output can be switched in any one of the optical input wavelengths in a relatively fast response time by applying injection current pulses. Analytical expression based on linear stability analysis is presented to predict the switching time to free oscillating mode, and larger optical input power and detuning are effective to shorten the switching time. The results here are believed to be useful to extend wavelength switching to a scope of electronic manipulation without modulation of optical inputs and can be applicable to actual devices.     

Dynamics of Optical Switching and Stability Analysis of a Polarization Bistable Laser Diode with Detuned External Light Injection

Dynamic behaviors of a polarization-bistable laser diode with detuned light injection are studied, including slow, fast and overshoot switching processes. Dependences of switching time of optical outputs between locked and free oscillating modes on the detuning and power of optical input, carrier injection rate and cross-gain saturation coefficients are investigated. Based on linear stability analysis the system stability is analyzed and analytical expressions are developed to predict the switching time. Our analytical results, in which the switching of optical output from locked to unlocked modes is shown to be composed of two relaxation processes with short and long time constants, are in agreement with the numerical results showing fast and slow switching behaviors dependent on the initial locked state, in contrast to the dynamic behavior of the carrier density dominated by a single relaxation process.     

半导体激光放大器的电路模型及噪声特性分析

给出了半导体激光（ＬＤ）放大器的电路模型，使得对半导体激光放大器的特性可以用通用电路分析软件进行分析。用该模型对谐振型光放大器光功率输出特性与失谐关系进行了模拟分析，模型的分析结果与已报道的理论和实验基本一致；用该模型还对谐振光放大器的噪声进行了分析。     

Dynamics of an Optically Switched Bistable Semiconductor Laser

The switching time of an optically switched laser diode between a locked mode and free oscillation mode is studied. By starting with linear stability analysis, analytical expressions are developed to predict the switching time. It is shown that the switching of optical output between the locked and unlocked modes is governed by two relaxation processes with different time constants, and the change in the first relaxation process, dependent on the carrier density in the initial state, gives a strong effect on the total switching time, in contrast to the dynamic behavior of the carrier density dominated by a single relaxation process. Our analytical results show that larger detuning and power of optical input are effective in shortening the switching time and are believed useful to estimate the switching time of an optically switched bistable laser diode.     

Properties of Optical Phase-Locked Loop Based on Four Wave Mixing in Semiconductor Laser Amplifiers

In this paper, the properties of the optical phase-locked loop(PLL) based on the four-wave mixing in the semiconductor laser amplifiers (SLAs) are discussed. The components that achieve the function of detecting the bit phase of the input optical signal are concerned and discussed in detail together as a function module named as the optical bit phase detector referred to the general electronic PLL. Therefore, most of the properties of the optical PLL can be analyzed by applying the general phase-locked theory. Here the stability of the optical PLL is discussed. It's shown that the variance of input signal power in the practical application will cause optical PLL system unstable because of its long loop delay. The influence on the output phase jitter of the optical PLL is also investigated.     

半导体激光器混沌输出的延时特征和带宽

外腔延时特征和带宽是影响混沌激光应用的两个重要参量.本文将一个单路光反馈的半导体激光器输出的激光部分地注入到另一个双路滤波光反馈的半导体激光器中,从而构成一个具有外光注入的双路滤波光反馈半导体激光器系统,即主从激光器系统,用于抑制混沌激光的延时特征并研究其带宽.数值研究了外光注入系数、反馈强度、抽运因子和滤波器带宽对系统输出混沌激光的延时特征的影响,然后将该系统对延时特征的抑制效果和具有外光注入的单路光反馈半导体激光器系统、具有外光注入的双路光反馈半导体激光器系统、具有外光注入的单路滤波光反馈半导体激光器系统以及无光注入双路滤波光反馈半导体激光器系统进行对比和分析,结果表明本文提出的方案对延时特征的抑制效果最好.然后在本文提出的具有外光注入的双路滤波光反馈半导体激光器系统中,延时特征被有效抑制的参数条件下研究系统输出混沌激光的带宽,结果表明,通过适当选择参数的取值,本文提出的方案可以提高系统输出混沌激光的带宽.     

Low-frequency fluctuation induced by injection-current modulation in semiconductor lasers with optical feedback

Low-frequency fluctuations in semiconductor lasers with optical feedback are investigated when high-frequency modulation is applied to an injection current. Synchronization of the laser output power with the modulation within +/-3 MHz centered at the frequency corresponding to the external cavity mode was observed. However, for modulation of the detuned frequency from the external cavity mode, low-frequency fluctuations were induced in the laser output power, and these fluctuations were observed within a range of modulation of approximately +/-100 MHz at the center frequency of the external cavity mode.     

集成双波导半导体光放大器光开关实现波长转换的理论研究

建立了基于集成双波导半导体光放大器的光开关(ITG-SOA-Switch)的理论分析模型.与半导体光放大器(SOA)的特性相比较表明，由于ITG-SOA-Switch合并了多种物理效应，故其静态增益饱和曲线在饱和功率点附近具有大幅度陡峭下降的独特性质.理论分析和10 Gbit/s波长转换模拟结果显示，恰当地选择输入抽运光的功率范围，ITG-SOA-Switch波长转换器输出转换光的消光比特性较之输入抽运光会有显著的改善. 关键词： 波长转换 半导体光放大器 集成双波导半导体光放大器 光开关     

Dynamics of Semiconductor Lasers with Optical Feedback from Photorefractive Phase Conjugate Mirror

The dynamics of semiconductor lasers with photorefractive phase conjugate optical feedback are experimentally studied. Photorefractive fringes considered here are rather static compared with time fluctuations of laser output power. Therefore, it is expected that a semiconductor laser with photorefractive feedback shows similar dynamics to those with conventional optical feedback. We examine relaxation oscillation and external cavity modes of laser output power in the presence of photorefractive phase conjugate feedback. It is proved that the dynamics of photorefractive phase conjugate feedback are fundamentally the same as those of conventional optical feedback.     

快速耦合光纤过程与半导体激光器电光特性实验的研究

详细地介绍了怎样快速耦合半导体激光器所发射激光与普通光纤输入端端面的方法,使耦合效率尽可能达到最大,并使用简单的方法测量了光纤的剩余长度或者测量光速,最后给出据测量半导体激光器电光特性曲线可准确方便地获得阈值电流的方法。     

可调谐半导体环形激光器与FWM全光波长变换实验研究

优化设计半导体光纤环形激光器(SFRL)产生波长连续可调谐窄线宽的激光输出,可调谐范围为40nm,利用半导体光放大器(SOA)的非线性效应四波混频(FWM),实现了码速为2.5Gb/sSDH信号光的波长变换,向上变换7.07nm,向下变换19.49nm.在实验中不需要外加泵浦光源.     

光学元件波前畸变对驱动器光路设计的影响

高功率激光驱动器光路设计要考虑像传递、鬼像规避和杂散光管理等多项优化措施.基于衍射光学传播理论,从输出负载能力提升的角度研究大口径光学元件波前特性对驱动器光路设计参数优化的影响.研究表明,驱动器末级光路的排布间隔如果控制在6 m以上,将非常有助于提高激光驱动器的输出负载能力.一般情况下,波前峰谷值达到0.34λ的单块大口径光学元件能使高功率激光的近场光束质量最大下降约10%,达到1.36λ后最大下降约21%;波前分布特性不同的多片大口径光学元件的波前相消叠加有利于降低中频波前部分对装置负载能力的影响,但是,大口径光学元件的非线性效应会加重中频波前对装置输出负载能力的影响;在限定大口径元件损伤阈值20J/cm~2的前提下,光路排布紧凑的激光驱动器末级输入激光通量控制在16.8J/cm~2之下不易损伤光学元件.相对宽松的光路设计可以进一步提高末级输出激光的平均通量水平,非常有利于激光驱动器装置输出负载能力的提升.     

基于注入锁定法布里-珀罗激光器的光学双稳态及光存储研究

研究基于注入锁定法布里-珀罗激光器的全光双稳态效应及其在全光存储中的应用. 进行了法布里-珀罗激光器的注入锁定的实验研究, 对注入锁定的法布里-珀罗激光器的输出功率特性进行实验分析, 得到了不同注入光波长失谐量对迟滞曲线的门限宽度和消光比的影响. 进一步, 通过对控制信号功率的合理设置, 实现了对10 Gb/s输入信号的2.5 GHz光存储验证了利用注入锁定法布里-珀罗激光器实现高速全光存储的可行性, 在高速光纤通信领域具有极大的应用价值.     

外光注入半导体激光器实现时钟分频

从理论和实验上研究了利用光注入半导体激光器对高重复速率光脉冲产生的周期振荡和时钟分频现象.结果表明，光注入半导体激光器引起的二倍周期振荡是使注入脉冲重复频率分频的直接原因.通过耦合速率方程，数值模拟了半导体激光器在外光注入时输出光的时间序列和功率谱，并且分析了激光腔内各种周期振荡的特征.研究表明，当注入光使半导体激光器出现稳定的二倍周期振荡，且注入光的重复频率为此振荡频率的二倍时，时钟分频即可产生实验中，采用重复频率为6.32GHz的光脉冲注入Fabry-Perot激光器，实现了3.16GHz时钟分频信号 关键词： 周期振荡 时钟分频 光谱侧带 光注入     

Monolithic integration of dual-layer optics into broad-area semiconductor laser diodes

A broad-area semiconductor laser diode with two monolithically integrated optical elements is presented. A 275-nm period detuned second-order diffraction grating on the p-doped side layer is combined with a refractive lens transferred into the GaAs substrate so that outcoupling and beam-shaping functions are decoupled. The high-power device produces a circular spot and demonstrates the potential of dual optics integration in broad-area semiconductor diodes.     

多调制延时耦合半导体激光器的混沌同步与编码

数值研究了非相干光反馈与非相干光注入半导体激光器的多调制延时混沌同步,由于该系统是基于非相干注入的,所以不需要接收激光器的频率与发送激光器频率完全匹配。通过对非相干光反馈半导体激光器输出自相关函数的研究,发现在多调制延时系统中,延时标识可以被隐藏,这一特性可以提高系统的安全性,非常适用于混沌保密通信系统。分别利用混沌移位键控(CSK)及混沌隐藏(CMS)编码方法考查了单向耦合和双向耦合系统的通信性能。     

采用Damman光栅实现冷原子或冷分子囚禁的光阱阵列

提出了一种采用Damman光栅和球面透镜组合光学系统产生二维光阱阵列的新方案. 在使用红失谐高斯激光束照射的条件下，推导了计算光阱阵列的周期、光强分布、光强梯度和光阱几何参数的经验公式，讨论了此光阱阵列的特点以及在原子光学和分子光学中的应用. 研究结果表明，这种光阱阵列方案比已有的光阱阵列方案更为简单可行、操作方便，非常适用于冷原子或冷分子的阵列囚禁，以及制备新颖的光学晶格. 关键词： 冷原子或冷分子 光阱阵列 Damman光栅 光偶极势     

A proposed semiconductor laser pump-probe source

A model is presented which determines the output from a semiconductor laser as a function of the direct current (d.c.) and radio frequency (r.f.) current applied to the laser. It is shown that by adjusting these two components the output optical pulse from a laser can be shifted in time without change to the pulse shape or height. Experimental results are presented which support the model. It is suggested how these results can be used to produce a semiconductor pump-probe source, which is essential for the development of optical probing.     

All-optical NOT and XOR logic operation at 2.5 Gb／s based on semiconductor optical amplifier loop mirror

All-optical XOR and NOT logic operations based on semiconductor optical amplifier loop mirror (SLALOM) aresimultaneously demonstrated theoretically and experimentally. Based on a segmented semiconductor optical amplifier model, the all-optical logic operation process is simulated theoretically. In an experimental study, 2.5 Gb/s all-optical XOR operation was achieved in the output port of SLALOM, while all-optical NOT operation was achieved in the input port through a circulator at the same time.