电化学合成PtCo/石墨烯复合催化剂及对甲醇的电催化氧化

以ITO导电玻璃为基体,采用恒电位沉积法制备了PtCo/石墨烯(GN)复合催化剂.通过扫描电镜(SEM),X射线能量散射谱(EDX)及电化学方法对催化剂进行了表征.SEM结果表明,石墨烯能够促进催化剂粒子的均匀分布,降低催化剂粒径;当Pt和Co物质的量之比为1∶2.93时,该催化剂粒径最小,分布最为均匀.电化学测试结果表明,石墨烯作为载体能够提高催化剂抗CO中毒性能,有利于对甲醇的催化氧化,这主要是由石墨烯优异的电子导电性和表面含氧活性基团所决定的.而且由于Co特殊的电子效应,它的加入也能够影响该催化剂的催化活性.结果证明,当Pt和Co物质的量之比为1∶2.93时,该复合催化剂表现出对甲醇氧化最为优越的催化性能,甲醇氧化峰电流密度可达到662A gpt-1,正反扫电流(If/Ib)比为2.34,是传统PtCo/C催化剂(If/Ib=1.32)的近1.8倍.     

纳米金/石墨烯复合膜修饰电极检测异烟肼EI北大核心CSCD

先采用滴涂法制备了石墨烯修饰电极(GR/GCE),然后采用电化学方法将纳米金沉积于石墨烯表面制备了纳米金/石墨烯复合材料修饰电极(Au NPs/GR/GCE)。研究了异烟肼(isoniazid,INZ)在该Au NPs/GR/GCE上的电化学行为。结果表明,异烟肼在该修饰电极上有良好的电化学响应。在优化条件下,线性扫描伏安法测定异烟肼的线性范围为1.0×10-7~1.0×10-4mol/L,检出限为5.0×10-8mol/L(S/N=3)。用该法测定了异烟肼注射液中异烟肼的含量,结果令人满意。     

纳米金/石墨烯复合膜修饰电极检测异烟肼

先采用滴涂法制备了石墨烯修饰电极(GR/GCE),然后采用电化学方法将纳米金沉积于石墨烯表面制备了纳米金/石墨烯复合材料修饰电极(Au NPs/GR/GCE)。研究了异烟肼(isoniazid,INZ)在该Au NPs/GR/GCE上的电化学行为。结果表明,异烟肼在该修饰电极上有良好的电化学响应。在优化条件下,线性扫描伏安法测定异烟肼的线性范围为1.0×10-7~1.0×10-4mol/L,检出限为5.0×10-8mol/L(S/N=3)。用该法测定了异烟肼注射液中异烟肼的含量,结果令人满意。     

石墨烯-钙钛矿结构光电化学传感器的构建及测定土壤中稀禾啶

研究了土壤中稀禾啶在石墨烯(Gr)、钙钛矿(CH_3NH_3PbI_3)化学修饰导电玻璃(ITO)上的光电化学行为。将石墨烯分散液、钙钛矿前驱液旋涂在ITO玻璃表面制备光电化学传感器,以时间-电流法研究稀禾啶在ITO/Gr/CH_3NH_3PbI_3上的光电响应及其选择性。在pH为7.0的磷酸盐缓冲溶液,光电流值与稀禾啶的浓度在2.0×10~(-7)～2.0×10~(-5) mol·L~(-1)范围内呈良好的线性关系,检测限为8.0×10~(-9 )mol·L~(-1)。该方法具有成本低、操作方便,重复性好、灵敏度高,并可用于土壤中稀禾啶的光电化学检测。     

对乙酰氨基酚分子印迹传感器的制备研究

将石墨烯(GR)与三氯化铁和铁氰化钾混合反应,合成了一种具有良好分散性的石墨烯-普鲁士蓝(GRPB)复合纳米材料,将GR-PB滴涂在玻璃碳电极(GCE)上,以邻甲苯胺为功能单体,对乙酰氨基酚为模板分子进行电化学聚合,制备了一种基于分子印迹的电化学传感器,用于定量测量对乙酰氨基酚的含量。通过扫描电镜、循环伏安和交流阻抗对该传感器进行了表征。实验结果表明,石墨烯-普鲁士蓝可以有效提高传感器的电化学灵敏度;在对乙酰氨基酚浓度范围为1.0×10^-5mol·L^-1至2.0×10^-7 mol·L^-1之间,传感器表现出良好的线性响应,检测限为7.37×10^-8 mol·L^-1。以药物中的对乙酰氨基酚作为实际样品,制备的传感器具有良好的准确性和精密度。     

碳纳米管/聚苯胺/石墨烯复合纳米碳纸及其电化学电容行为

通过真空抽滤的方法制备碳纳米管纸,并对其进行循环伏安电化学氧化处理.以该电化学氧化处理的碳纳米管(CV-CNT)纸为基体,采用电化学聚合沉积聚苯胺(PANI),随后吸附石墨烯(GR),制备具有三明治夹心结构的碳纳米管/聚苯胺/石墨烯(CV-CNT/PANI/GR)复合纳米碳纸.该结构外层为GR,内层由PANI包裹的CNT形成网络骨架,充分发挥三者各自优势构建柔性电极材料.用场发射扫描电镜(FE-SEM)、透射电子显微镜(TEM)、拉曼光谱对其形貌与结构进行表征,并测试其电化学性能.研究发现:PANI呈纳米晶须状,并均匀包裹在CV-CNT表面;该复合碳纸具有良好的电容特性、大电流充放电特性以及良好的循环稳定性能.电流密度为0.5A·g-1时,比电容可达415F·g-1;20A·g-1时仍能保持106F·g-1的比电容.由于GR的保护作用,1000次循环之后较CV-CNT/PANI保持更高的有效比电容.该CV-CNT/PANI/GR复合碳纸展现出在高性能超级电容器柔性电极材料的潜在应用价值.     

石墨烯-ITO复合电极对聚苯胺薄膜电致变色性质的影响

采用改进的Hummers法制备氧化石墨烯(GO),首先,石墨与浓硫酸、过硫酸钾和五氧化二磷反应制得强氧化产物,随后将其与浓硫酸、硝酸钠、高锰酸钾反应,经双氧水发泡、酸洗、超声等合成氧化石墨烯水溶液,再通过金属箔还原和基底转移过程制备GO-氧化铟锡(ITO)复合电极材料.通过金属箔还原和基底转移过程制备GO-氧化铟锡(ITO)复合电极材料.利用电化学聚合法在GO-ITO复合电极上制备聚苯胺(PANI)薄膜,并对其形貌结构、电化学及电致变色性质进行表征.结果表明,与ITO电极相比,采用GO-ITO复合电极制备的PANI的成膜性得到明显改善,复合电极具有更加均匀细致的颗粒表面,增大了聚合物与电解液之间的接触面积,为电致变色过程中平衡离子的注入/脱出提供了更多的通道,因而PANI薄膜在700nm处的光学对比度提高了约13%,响应速度缩短了约2.6 s,着色效率高达169.6 cm2/C.GO的引入保持了PANI良好的电化学稳定性.GO-ITO复合电极有效改善了聚合物的综合性能,对于聚合物电致变色材料及器件的开发具有潜在的应用前景.     

三维石墨烯的制备及其在电化学生物传感器中的研究现状

三维石墨烯具有多孔网络结构、大的比表面积、高的导电性、优异机械性能和良好的生物相容性,作为电化学生物传感器电极材料在检测生物分子方面表现出优异的性能,是一种非常理想的电化学生物传感器电极材料。本文综述了三维石墨烯的制备方法及其在电化学生物传感器中最新的研究进展。     

硫堇/Nafion/石墨烯修饰电极对NADH的电催化活性研究

为了提高电化学检测NADH的分析性能,制备了硫堇/Nafion/石墨烯修饰的玻碳电极(GCE),利用Nifion的强离子交换能力将硫堇修饰在电极表面,形成硫堇/Nafion/石墨烯复合电极.与裸玻碳电极相比,在NADH的反应中观察到了电位明显降低和电流响应显著增大.证实了硫堇/Nafion/石墨烯复合电极对NADH有协同的电催化能力.为构造有效地检测NADH的电化学传感器提供一个良好的应用平台.     

ITO表面Pt颗粒的电化学沉积制备及其电催化氧化氨研究

以氧化铟锡(ITO)透明导电玻璃为导电基体, 采用恒电位电化学沉积方法, 在其表面制备Pt颗粒. 使用扫描电子显微镜(SEM), 能量色散X射线荧光光谱(EDS)与X射线衍射(XRD)表征了ITO表面沉积的Pt颗粒的形貌, 成分和结构. 采用循环伏安(CV)和电化学活性面积(EASA)表征Pt/ITO电极在碱性介质中对氨的电催化氧化性能及其有效电化学表面积. 结果表明, 采用电化学沉积方法, 可在ITO表面获得具有较好分散度的亚微米尺寸的Pt颗粒. 制备的Pt/ITO电极在较低Pt担载量(约0.12 mg•cm^－2)的条件下, 即可获得远高于纯Pt电极的电催化氧化氨活性. 这主要归因于电化学沉积制备的Pt颗粒尺寸较小且在ITO表面呈良好分散, 具有很高的电化学活性面积.     

Synthesis of graphene oxide nanosheet: A novel glucose sensor based on nickel-graphene oxide composite film

The graphene oxide (GO) nanosheets were produced by chemical conversion of graphite, and were characterized by transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR). An electrochemical sensor based on Ni/graphene (GR) composite film was developed by incorporating Ni²⁺ into the graphene oxide film modified glassy carbon electrode (Ni/GO/GCE) through the electrostatic interactions with negatively charged graphene oxide. The Ni²⁺/graphene modified glassy carbon electrode (Ni/GR/GCE) was prepared by cyclic voltammetric scanning of Ni/GO/GCE in the potential range from ?1.5 to 0.2 V at 50 mV s^?1 for 5 cycles. The electrochemical activity of Ni/GR/GCE was illustrated in 0.10 M NaOH using cyclic voltammetry. The Ni/GR/GCE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple. The introduction of conductive graphene not only greatly facilitates the electron transfer of Ni²⁺, but also dramatically improves the long-term stability of the sensor by providing the electrostatic interactions. Ni/GR/GCE also shows good electrocatalytic activity toward the oxidation of glucose. The Ni/GR/GCE gives a good linear range over 10 to 2700 μM with a detection limit of 5 μM towards the determination of glucose by amperometry. This sensor keeps over 85% activity towards 0.1 mM glucose after being stored in air for a month, respectively. Furthermore, the modified sensor was successfully applied to the sensitive determination of glucose in blood samples.     

A facile approach for synthesizing molecularly imprinted graphene for ultrasensitive and selective electrochemical detecting 4-nitrophenol

In this work, a novel and convenient strategy was developed to prepare molecularly imprinted polymers (MIPs) on the surface of graphene sheet. In this route, vinyl group functionalized graphene (GR/NVC) was first prepared by immobilizing 4-vinylcarbazole onto the surface of graphene via π–π interaction. The subsequent grafting copolymerization of methacrylic acid and ethylene glycol dimethacrylate in the presence of 4-nitrophenol (4-NP, template molecule) was carried out at GR/NVC surface, leading to the formation of GR/MIPs composite. The GR/MIPs composite was characterized by FTIR, fluorescence, TGA, SEM and AFM, and was used to fabricate electrochemical sensor for the detection of 4-NP. The electrochemical behavior of GR/MIPs sensor for 4-NP was investigated by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The effects of the preparation conditions, such as concentration of the NVC and template, the solution pH, and incubation time, were also optimized. Under optimized conditions, the DPV current response of GR/MIPs sensor was nearly 12 times than that of the GR/NIPs sensor. It also should be noted that as compared to traditional MIP, shorter response time and much higher current response were demonstrated. In addition, the GR/MIPs sensor could recognize 4-NP from its structural analogs, indicating the excellent selectivity of the GR/MIPs sensor. The peak current is linearly proportional to the concentration of 4-NP ranging from 0.01 μM to 100 μM and 200 μM to 1000 μM with a significantly low detection limit of 5 nM, a wider response range and lower detection limits as compared to most of the previously reported electrochemical sensors for 4-NP. Furthermore, the GR/MIPs sensor exhibits good stability with adequate reproducibility and has been successfully used to determine 4-NP in water samples.     

Electrochemical Determination of Hydrogen Peroxide Using a Glassy Carbon Electrode Modified with Three-Dimensional Copper Hydroxide Nanosupercages and Electrochemically Reduced Graphene Oxide

Three-dimensional copper hydroxide nanosupercages and electrochemically reduced graphene oxide were used to modify the glassy carbon electrode for the selective determination of hydrogen peroxide. The morphology and electrochemistry properties of copper hydroxide nanosupercage/electrochemically reduced graphene oxide/glassy carbon electrode were characterized using transmission electron microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectra, Raman spectra, cyclic voltammetry, and electrochemical impedance spectroscopy. The resulting copper hydroxide nanosupercage/electrochemically reduced graphene oxide/glassy carbon electrode showed favorable performance for the electrocatalytic reduction of hydrogen peroxide. The amperometric current–time curve of the electrochemical sensor exhibited a wide linear range from 0.5 to 1030?µM with a limit of detection of 0.23?µM at a signal-to-noise ratio of three. Moreover, the sensor provided favorable selectivity, reproducibility, and stability and was used for the determination of H₂O₂ in tap water.     

柔性复合织物电极Graphene/Cotton和MnO2/Graphene/Cotton的合成及在电化学电容器中的应用

通过热还原法成功地制备出了柔性复合织物电极石墨烯/棉布(graphene/cotton)。热还原条件对电极的导电性能具有较大的影响。导电柔性织物电极graphene/cotton特有的多级结构使其既有利于进一步负载膺电容材料,又有利于电子和电解质离子的传输与扩散。通过电化学沉积方法,利用导电柔性织物电极graphene/cotton进一步制备出了电极MnO₂/graphene/cotton。利用扫描电子显微镜(SEM),傅里叶变换红外(FTIR)光谱,四探针测试法等表征技术对电极的结构进行了较为详细的表征。结果表明电极MnO₂/graphene/cotton的比电容可以达到536 F·g^-1。良好的电化学性能和柔性使得此类电极在柔性储能材料应用中具有极大的应用前景。     

碳纳米管负载纳米金-石墨烯量子点修饰电极电化学检测过氧化氢

采用过氧化氢刻蚀法制备石墨烯量子点(GQDs),再采用原位化学还原法制备金纳米粒子-石墨烯量子点纳米复合物(Au NPs-GQDs),最后以聚二甲基二烯丙基氯化铵(PDDA)为交联剂将上述纳米复合物组装于多壁碳纳米管表面,制得金纳米粒子-石墨烯量子点-PDDA-多壁碳纳米管复合材料(Au NPs-GQDsPDDA-MWCNTs)。通过荧光光谱法、紫外-可见吸收光谱法和透射电子显微镜对上述复合材料进行表征。采用滴涂法制得该复合材料修饰的玻碳电极,研究了过氧化氢在该电极上的电化学行为。结果表明:在石墨烯量子点、金纳米粒子和多壁碳纳米管三者的协同作用下,该电极对过氧化氢的电氧化表现出强的催化活性。在优化条件下,安培法检测H_2O_2的线性范围为2.0×10~(-8)~1.5×10~(-3)mol/L,检出限(3sb)为8.0×10~(-9)mol/L,灵敏度为61.6μA/(mmol·L~(-1))。     

Direct electrochemistry-based hydrogen peroxide biosensor formed from single-layer graphene nanoplatelet-enzyme composite film

A novel electrochemical sensing system for direct electrochemistry-based hydrogen peroxide biosensor was developed that relied on the virtues of excellent biocompatibility, conductivity and high sensitivity to the local perturbations of single-layer graphene nanoplatelet (SLGnP). To demonstrate the concept, the horseradish peroxidase (HRP) enzyme was selected as a model to form the SLGnP-TPA (tetrasodium 1,3,6,8-pyrenetetrasulfonic acid)-HRP composite film. The single-layer graphene composite film displayed a pair of well-defined and good reversible cyclic voltammetric peak for Fe(III)/Fe(II) redox couple of HRP, reflecting the enhancement for the direct electron transfer between the enzyme and the electrode surface. Analysis using electrochemical impedance spectroscopy (EIS) revealed that electrostatic attractions existed between graphene monolayers and enzyme molecules. The intimate graphene and enzyme interaction was also observed using scanning electron microscopy (SEM), which resulted in the special properties of the composite film. Ultraviolet visible spectroscopy (UV-vis) indicated the enzyme in the composite film retained its secondary structure similar to the native state. The composite film demonstrated excellent electrochemical responses for the electrocatalytic reduction of hydrogen peroxide (H₂O₂), thus suggesting its great potential applications in direct electrochemistry-based biosensors.     

Free‐standing and Flexible MoS2/rGO Paper Electrode for Amperometric Detection of Folic Acid

The development of flexible electrodes is of considerable current interest because of the increasing demand for modern electronics, portable medical products, and compact devices. We report a new type of flexible electrochemical sensor fabricated by integrating graphene and MoS₂ nanosheets. A highly flexible and free‐standing conductive MoS₂ nanosheets/reduced graphene oxide (MoS₂/rGO) paper was prepared by a two‐step process: vacuum filtration and chemical reduction treatment. The MoS₂/graphene oxide (MoS₂/GO) paper obtained by a simple filtration method was transformed into MoS₂/rGO paper after a chemical reduction process. The obtained MoS₂/rGO paper was characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy, electrochemical impedance spectroscopy. The electrochemical behavior of folic acid (FA) on MoS₂/rGO paper electrode was investigated by cyclic voltammetry and amperometry. Electrochemical experiments indicated that flexible MoS₂/rGO composite paper electrode exhibited excellent electrocatalytic activity toward the FA, which can be attributed to excellent electrical conductivity and high specific surface area of the MoS₂/rGO paper. The resulting biosensor showed highly sensitive amperometric response to FA with a wide linear range.     

基于石墨烯分子印迹电化学传感器测定芦丁

将石墨烯(GR)滴涂至裸Au电极表面,并以邻氨基酚为功能单体,芦丁为模板分子,制备了芦丁分子印迹膜电化学传感器,利用循环伏安法(CV)和差分脉冲伏安法(DPV)对制得的传感器进行了电化学性能研究,并且对制备条件和测定条件进行了优化。结果表明,与裸Au电极相比,该GR修饰的Au电极在[Fe(CN)_6]~(3-/4-)溶液中峰电流明显增大,显著提高了芦丁分子印迹传感器的灵敏度。在最优实验条件下,基于GR分子印迹电化学传感器在4.40×10~(-6)~2.80×10~(-4) mol/L范围内呈良好的线性关系,检测限为1.46×10~(-6) mol/L。用该传感器测定了黑茶中芦丁的含量,获得较好结果。     

One-step preparation of silver nanoparticle embedded amorphous carbon for nonenzymatic hydrogen peroxide sensing

Herein, we report a rapid and facile fabrication of Ag/C hybrid by anchoring Ag nanoparticles in amorphous carbon network for application in amperometric sensing of hydrogen peroxide. Ag/C hybrid was prepared by simply mixing silver nitrate aqueous solution with ethylene glycol and diphosphorus pentoxide in one step at room temperature. The embedding of Ag nanoparticles into the amorphous carbon support can greatly strengthen the stability of Ag nanoparticles, protecting them from oxidizing without loss of conductivity. The nanocomposite was investigated by transmission electron microscopy, energy dispersive X-ray analysis, X-ray diffraction technique, X-ray photoelectron spectroscopy and electrochemical measurements. The prepared Ag/C hybrid was fabricated onto the surface of glassy carbon electrode to investigate the sensing property towards hydrogen peroxide. The fabricated electrochemical sensor can determine hydrogen peroxide with a detection limit of 0.1 μM and up to 5.5 mM.