Microstructural and surface property variations due to the amorphous region formed by thermal annealing in Al-doped ZnO thin films grown on n-Si (1 0 0) substrates

X-ray diffraction (XRD) patterns revealed that the as-grown and annealed Al-doped ZnO (AZO) films grown on the n-Si (1 0 0) substrates were polycrystalline. Transmission electron microscopy (TEM) images showed that bright-contrast regions existed in the grain boundary, and high-resolution TEM (HRTEM) images showed that the bright-contrast regions with an amorphous phase were embedded in the ZnO grains. While the surface roughness of the AZO film annealed at 800 °C became smoother, those of the AZO films annealed at 900 and 1000 °C became rougher. XRD patterns, TEM images, selected-area electron diffraction patterns, HRTEM images, and atomic force microscopy (AFM) images showed that the crystallinity in the AZO thin films grown on the n-Si (1 0 0) substrates was enhanced resulting from the release in the strain energy for the AZO thin films due to thermal annealing at 800 °C. XRD patterns and AFM images show that the crystallinity of the AZO thin films annealed at 1000 °C deteriorated due to the formation of the amorphous phase in the ZnO thin films.     

The influence of preparative parameters on the adhesion of alumina washcoats deposited on metallic supports

Well-adhered alumina washcoats on FeCrAl metallic supports were prepared using boehmite sols and alumina slurries. The microstructure and the surface performance of the washcoat/support were investigated by SEM, XRD, and ultrasonic vibration. The effects of the main preparative parameters on the coating adherence were studied. The optimal coating conditions are presented as follows: pre-oxidation of the metallic supports was performed at 900 °C for 10 h, the sol layer loadings were 2.0-6.6 wt.%, and the slurry layer loadings were less than 25.3 wt.%. The sol layer drying was performed at 30 °C for 1 h and that for the slurry layer the drying was performed at 120 °C for 2 h, and the coating calcining was performed at 900 °C for 2 h. The SEM photographs of coated samples show that alumina washcoats were well deposited on the metallic supports.     

Spray pyrolytic deposition of transparent aluminum oxide (Al2O3) films

Optically transparent Al₂O₃ films has been synthesized, on quartz substrates at 500, 600 and 700 °C, from 0.02 M aluminum acetyl acetonate (Al(acac)₃) in ethanol, by using ultrasonic spray pyrolysis technique. The films synthesized at 500, 600 and 700 °C are amorphous having average particle sizes 27 ± 6, 18 ± 3 and 14 ± 3, respectively. The films are found to be 95% optically transparent in the visible region. The optical transparency of the films in the ultraviolet region is found to increase with increase in deposition temperature. The observed increase in optical band gap and decrease in refractive index is attributed to the decrease in particle size with increase in deposition temperature. The stoichiometry and chemical bonding of the amorphous film studied using XPS and FTIR spectroscopy revealed the presence chemisorbed oxygen.     

Solution-combustion synthesis of Tb-doped Y3Al5O12 nanoparticles

Nano-sized YAG:Tb powder phosphors were prepared by a solution-combustion method, using the general inorganic salts as starting materials. The X-ray diffraction (XRD) measurements showed that the precursor can be well-crystallized at 900 °C. As-prepared particles have sizes mostly in the range between 30 and 100 nm as obtained by scanning electron microscope (SEM) and transition electron microscope (TEM). Selected area electron diffraction (SAED) patterns proved that the larger particles are monocrystalline. The effects of annealing temperature and Tb-doping concentration on the luminescence intensity were studied.     

Structural,magnetic and Mössbauer spectral studies of nanosize aluminum substituted nickel zinc ferrites

Nanosize aluminum substituted nickel zinc ferrites were prepared through aerosol route and characterized using TEM, XRD, magnetic measurements and Mössbauer spectroscopy. The particle size of as obtained samples was found to be ∼10 nm which increases up to ∼85 nm upon annealing at 1200 °C. The unit cell parameter ‘a’ decreases linearly with concentration of aluminum due to the small ionic radius of aluminum. The saturation magnetization for all the samples after annealing at 1200 °C lies in the range 12.9–72.6 emu/g and decreases linearly with concentration of aluminum. Room temperature Mössbauer spectra of all as obtained samples of ferrite compositions exhibited a broad doublet suggesting super paramagnetic nature. This doublet is further resolved into two doublets and assigned to the surface region and internal region atoms of the particles. The samples annealed at 1200 °C show broad sextets, which were fitted with five sextets, indicating different local environment of both tetrahedrally and octahedrally coordinated Fe cation.     

Preparation and properties of nanocrystalline powders in (Y1−xCex)3Al5O12 system

Nano-sized cerium-doped yttrium aluminum garnet (YAG:Ce) phosphors were synthesized via a simple sol-gel process using metal nitrate precursors. The prepared phosphors were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and photoluminescence (PL) spectroscopy, respectively. Pure cubic garnet phase was formed at temperatures ∼900 ^οC. The particle sizes of as-prepared powders were mostly in the range of 17-27 nm. The crystalline YAG:Ce showed broad emission peaks in the range of 400-700 nm and maximum intensities at 500 and 520 nm. It is found also that the emission intensity decreased with increasing Ce doping concentration from 0.1 to 1.5 at%. With increasing Ce doping concentration, the PL intensity was shifted towards shorter wavelengths.     

Thermal stability of HfO2 nanotube arrays

Thermal stability of highly ordered hafnium oxide (HfO₂) nanotube arrays prepared through an electrochemical anodization method in the presence of ammonium fluoride is investigated in a temperature range of room temperature to 900 °C in flowing argon atmosphere. The formation of the HfO₂ nanotube arrays was monitored by current density transient characteristics during anodization of hafnium metal foil. Morphologies of the as-grown and post-annealed HfO₂ nanotube arrays were analyzed by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Although monoclinic HfO₂ is thermally stable up to 2000 K in bulk, the morphology of HfO₂ nanotube arrays degraded at 900 °C. A detailed X-ray photoelectron spectroscopy (XPS) study revealed that the thermal treatment significantly impacted the composition and the chemical environment of the core elements (Hf and O), as well as F content coming from the electrolyte. Possible reasons for the degradation of the nanotube at high temperature were discussed based on XPS study and possible future improvements have also been suggested. Moreover, dielectric measurements were carried out on both the as-grown amorphous film and 500 °C post-annealed crystalline film. This study will help us to understand the temperature impact on the morphology of nanotube arrays, which is important to its further applications at elevated temperatures.     

Interaction of ultrasonic waves with domain walls on nanocrystalline YIG

The nanocrystalline YIG samples with different particle sizes (20–40 nm) has been prepared using microwave–hydrothermal method. As synthesized powders were characterized using XRD and TEM. The powders were pressed and sintered at three different temperatures i.e., 700 °C/30 min, 800 °C/30 min, 900 °C/30 min, using microwave furnace. The sintered samples were characterized using XRD and TEM. The sintered samples are monophasic in nature with average grain size ranging in between 72 nm and 90 nm. The thermal variation of ultrasonic velocities [longitudinal (V_l) and transverse (V_S)] and longitudinal attenuation (α_l) has been measured on sintered samples by the pulse transmissionmethod at 1 MHz, in the temperature range of 300–600 K. The room temperature velocity is found to be grain size dependent and decreases with increasing temperature, except near the Curie temperature, T_C, where a small anomaly is observed. The longitudinal attenuation (α₁) at room temperature is also found to be more sample dependent. The temperature variation of ultrasonic longitudinal attenuation exhibits a sharp maximum just below Curie temperature (T_C). The above observations were carried on in the demagnetized state, on the application of a saturation field of 380 mT, the anomaly observed in the thermal variation of velocities (longitudinal and transverse) and attenuation is found to disappears. The observed interaction of ultrasonic velocity with domain walls has been qualitatively explained with the help oftemperature variation of magneto-crystalline anisotropy constant (k₁) and Landau’s theory.     

Effect of thermal annealing in the microstructural and the optical properties of uncapped InAs quantum dots grown on GaAs buffer layers

The effect of thermal annealing on self-assembled uncapped InAs/GaAs quantum dots (QDs) has been investigated using transmission electron microscopy (TEM) and photoluminescence (PL) measurements. The TEM images showed that the lateral sizes and densities of the InAs QDs were not changed significantly up to 650 °C. When the InAs/GaAs QDs were annealed at 700 °C, while the lateral size of the InAs QDs increased, their density decreased. The InAs QDs disappeared at 800 °C. PL spectra showed that the peaks corresponding to the interband transitions of the InAs QDs shifted slightly toward the high-energy side, and the PL intensity decreased with increasing annealing temperature. These results indicate that the microstructural and the optical properties of self-assembled uncapped InAs/GaAs can be modified due to postgrowth thermal annealing.     

Crystallization and electrochemical performance of La0.6Sr0.4Co0.2Fe0.8O3 − δ-Ce0.8Gd0.2O1.9 thin film cathodes processed by single solution spray pyrolysis

La_0.6Sr_0.4Co_0.2Fe_0.8O_3 − δ-Ce_0.8Gd_0.2O_1.9 (LSCF-CGO) thin films obtained by spray pyrolysis of a single precursor solution were investigated by XRD, TEM and impedance spectroscopy at annealing temperatures ranging from 500 to 900 °C. Films annealed at 600 °C contained a mixture of amorphous regions and crystalline regions composed of fine crystallites (< 5 nm). Annealing above 600 °C increased the ratio of crystalline to amorphous material, led to the segregation of the films into distinct LSCF and CGO phases, and promoted grain growth. The electrical behavior of the films depended on annealing temperature. At testing temperatures of 400 °C and below, the polarization resistance of films with lower annealing temperatures was larger than the polarization resistance of films with higher annealing temperatures. However, at testing temperatures of 500 °C and above the polarization resistance of films with lower annealing temperatures was equal to or lower than the polarization resistance of films with higher annealing temperatures. This was reflected by the activation energy that decreased with increasing annealing temperature. The varying electrical behavior may be related to microstructural changes that caused bulk diffusion to be the rate-limiting step in films with lower annealing temperatures and oxygen dissociation to be the rate-limiting step in films with higher annealing temperatures.     

Enhancement of saturation magnetization in Cr-ion implanted silicon by high temperature annealing

Magnetic properties and microstructure of Cr-implanted Si have been investigated by alternating gradient magnetometer (AGM), superconducting quantum interference device (SQUID) magnetometer, and transmission electron microscopy (TEM). p-Type (1 0 0) Si wafers were implanted at 200 keV at room temperature with a dosage of 1 × 10¹⁶ cm⁻² Cr ions and then annealed at 600-900 °C for 5 min. The effect of annealing on the structure and magnetic properties of Cr-implanted Si is studied. The as-implanted sample shows a square M-H loop at low temperature. Magnetic signal becomes weaker after short time annealing of the as-implanted sample at 600 °C, 700 °C, and 800 °C. However, the 900 °C annealed sample exhibits large saturation magnetization at room temperature. TEM images reveal that the implanting process caused amorphization of Si, while annealing at 900 °C led to partial recovery of the crystal. The enhancement of saturation magnetization can be explained by the redistribution and accumulation of Cr atoms in the vacancy-rich region of Si during annealing.     

Microstructure and optical properties of ZnO nanoparticles prepared by a simple method

In this investigation, ZnO nanoparticles were prepared by a simple and rapid method. This method is based on the short time solid state milling and calcinations of zinc acetate and citric acid powders. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, photoluminescence and UV-vis spectroscopy. It was shown that the calcination temperature significantly affected the particle size and optical properties of the synthesized ZnO nanoparticles. Calculation based on the XRD data shows that the average sizes of ZnO particles are in agreement with those from TEM images and the size of the particles increases on increasing the calcination temperature. Also the band gap of samples decreased from 3.29 to 3.23 eV on increasing the calcination temperature from 350 to 600 °C. Photoluminescence analyses show that many defects such as interstitial zinc, zinc vacancy and oxygen vacancy are responsible for the observed optical properties.     

Solvothermal synthesis and luminescent properties of YAG:Tb nano-sized phosphors

Nano-sized Tb-doped YAG phosphor particles were synthesized by a mixed solvo-thermal method using stoichiometric amounts of inorganic aluminum and yttrium salts. The formation of YAG:Tb was investigated by means of XRD and IR spectra. The pure crystalline-phase YAG was prepared under moderate synthesis conditions (300 °C and 10 MPa), indicating that ethanol partly replaces water as the solvent, thus favoring the formation of YAG. TEM images showed that YAG:Tb phosphor particles sintered at 300 °C were basically of spherical shape, with good dispersion about a particle size of around 80 nm. The crystalline YAG:Tb showed green emission with ⁵D₄−⁷F₆ (544 nm) as the most prominent group. The PL intensity and crystallinity of YAG:Tb phosphors increases with increasing synthesis temperature, and reaches maximum brightness at 300 °C, which is lower than that exhibited by a commercial product.     

Temperature-induced changes in morphology and structure of TiO2-Al2O3 fibers

Electrospinning of a sol-gel and polymer mixture is used to produce titania-alumina (TiO₂-Al₂O₃) fibers with diameters ranging from 200 to 800 nm. These composite metal-oxide fibers were calcined at various temperatures and their morphology is studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The decrease in the average diameter of the fibers with increasing temperature is observed. Powder X-ray diffraction (XRD) reveals that up to 800 °C the composite fibers have anatase titania structure whereas at 900 °C the fibers exhibit mixture of anatase and rutile phases. It is found that specific surface area decreases as a function of temperature in the 700-900 °C range. The change in phase (anatase-to-rutile) and the increase in crystallite size occur simultaneously. The presence of smaller amount of amorphous alumina in the primarily titania-based structure seems to play the role in stabilizing the anatase phase.     

Magnetic properties of MnO nanocrystals dispersed in a silica matrix

Magnetic nanocrystalline MnO particles have been synthesized in a silica glass matrix by the sol-gel method at calcination temperatures up to 1000 °C. EPR spectra of 0.1 mol% MnO doped silica gel and glasses studied in the temperature range 10-290 K show with the exception of those samples calcined at 900 and 1000 °C 6-line characteristic Mn(II) hyperfine (HF) lines. Additionally five spin-forbidden doublets have been observed at 100 K and below. Small spreads in spin Hamiltonian parameters (D and E) imply that the ligand field environments of Mn(II) ions embedded in the silica glass are nearly uniform. Monotonous decrease in HF linewidth in going from 120 °C gel to 800 °C calcined glass has been interpreted as the continuous decrease in population of isolated Mn²⁺ ions in silica glass matrix resulting in the decrease of magnetic dipolar interactions leading to the observed decrease in HF linewidth. XRD and TEM of sample calcined at 1000 °C shows the presence of nanocrystals of MnO having orthorhombic crystalline phase and sizes about 10 nm. The thermal behavior of magnetization (zero-field-cooled and field-cooled) and magnetic hysteresis of MnO nanocrystals in the 5-300 K temperature interval have demonstrated that the MnO nanocrystals display superparamagnetic-ferromagnetic transition at low temperatures. X-band EPR linewidth data plotted versus inverse of temperature (1/T) for samples calcined at 900 and 1000 °C (EPR recorded in the vicinity of 0.35 T applied field) depict similar transitions.     

Effect of aluminium doping and annealing on structural and optical properties of cerium oxide nanocrystals

Nanocrystalline fluorite-like structures of Ce_1−xAl_xO_2−δ compounds were prepared by the chemical precipitation method using cerium chloride and aluminium chloride as precursors. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and diffuse reflectance spectroscopy (DRS). The effects of aluminium doping concentration and annealing on particle size, lattice parameter and band gap energies were investigated. The particle size of Al-doped CeO₂ samples were found to decrease with Al concentration and it increases from 6 to 20 nm as annealing temperature increases to 900 °C.     

Effect of iron doping and annealing on structural and optical properties of cerium oxide nanocrystals

Nanocrystalline fluorite-like structures of Ce_1−xFe_xO_2−δ compounds were prepared by chemical precipitation method using cerium chloride and iron chloride as precursors. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and diffuse reflectance spectroscopy (DRS). The effects of iron doping concentration and annealing on particle size, lattice parameter and band gap energies were investigated. The particle size of Fe-doped CeO₂ samples were found to decrease with iron concentration and it increases from 9 to 26 nm as annealing temperature increases to 900 °C.     

Effect of nanostructured AlN coatings on the oxidation-resistant properties of optical diamond films

Diamond film is an ultra-durable optical material with high thermal conductivity and good transmission in near-infrared and far-IR (8-14 μm) wavebands. CVD diamond is subjected to oxidation at temperature higher than 780 °C bared in air for 3 min, while it can be protected from oxidation for extended exposure in air at temperature up to 900 °C by a coating of aluminum nitride. Highly oriented AlN coatings were prepared for infrared windows on diamond films by reactive sputtering method and the average surface roughness (R_a) of the coatings was about 10 nm. The deposited films were characterized by X-ray diffraction (XRD) and atom force microscope (AFM). XRD confirmed the preferential orientation nature and AFM showed nanostructures. Optical properties of diamond films coated AlN thin film was investigated using infrared spectrum (IR) compared with that for as-grown diamond films.     

Thermal stability of the cubic phase in Ba0.5Sr0.5Co0.8Fe0.2O3 - δ (BSCF)1

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 - δ (BSCF) is a material with excellent oxygen ionic and electronic transport properties reported by many research groups. In its cubic phase, this mixed ionic-electronic conducting (MIEC) perovskite is a promising candidate for oxygen permeation membranes. For this application, its long-term stability under operating conditions (especially temperature and oxygen partial pressure) is of crucial importance.The present work is focused on the thermal stability of the BSCF cubic phase in the targeted temperature range for applications (700…900 °C) in light of previous studies in literature reporting a reversible transition to a hexagonal phase somewhere below 900 °C.To this end, single phase cubic BSCF powders were annealed at different temperatures over varying periods of time. Phase composition was subsequently analysed by X-ray diffractometry (XRD) in order to determine both the temperature limit and the time-scale for the formation of the hexagonal phase. Additionally, the long-term behaviour of the electrical conductivity was examined on bulk samples at 700 °C, 800 °C and 900 °C over several hundreds of hours, showing a prolonged decrease at 800 °C. The decrease in electrical conductivity at this temperature was also examined on bulk samples with different grain sizes, showing a more pronounced decrease the smaller the average grain size.Coexistence of both phases (cubic and hexagonal) could also be shown for 700 °C, however with a different phase equilibrium than at 800 °C.     

Phase transition and magnetic properties of Mg-doped hexagonal close-packed Ni nanoparticles

Mg-doped Ni nanoparticles with the hexagonal close-packed (hcp) and face-centered cubic (fcc) structure have been synthesized by sol-gel method sintered at different temperatures in argon atmosphere. The sintering temperature played an important role in the control of the crystalline phase and the particle size. The pure hcp Mg-doped Ni nanoparticles with average particle size of 6.0 nm were obtained at 320 °C. The results indicated that the transition from the hcp to the fcc phase occurred in the temperature range between 320 °C and 450 °C. Moreover, the VSM results showed that the hcp Mg-doped Ni nanoparticles had unique ferromagnetic and superparamagnetic behavior. The unsaturation even at 5000 Oe is one of the superparamagnetic characteristics due to the small particle size. From the ZFC and FC curves, the blocking temperature T_B of the hcp sample (6.0 nm) was estimated to be 10 K. The blocking temperature was related to the size of the magnetic particles and the magnetocrystalline anisotropy constant. By theoretical calculation, the deduced particle size was 6.59 nm for hcp Mg-doped Ni nanoparticles which was in agreement with the results of XRD and TEM.