Au/TiO2/Ru(0 0 0 1) model catalysts and their interaction with CO

Au/TiO₂/Ru(0 0 0 1) model catalysts and their interaction with CO were investigated by scanning tunneling microscopy and different surface spectroscopies. Thin titanium oxide films were prepared by Ti deposition on Ru(0 0 0 1) in an O₂ atmosphere and subsequent annealing in O₂. By optimizing the conditions for deposition and post-treatment, smooth films were obtained either as fully oxidized TiO₂ or as partly reduced TiO_x, depending on the preparation conditions. CO adsorbed molecularly on both oxidized and reduced TiO₂, with slightly stronger bonding on the reduced films. Model catalyst surfaces were prepared by depositing submonolayer quantities of Au on the films and characterized by X-ray photoelectron spectroscopy and scanning tunneling microscopy. From X-ray photoelectron spectroscopy, a weak interaction between the Au and the TiO₂ substrate was found. At 100 K CO adsorption occurred on both the TiO₂ film and on the Au nanoparticles. CO desorbed from the Au particles with activation energies between 53 and 65 kJ/mol, depending on the Au coverage. If the Au deposit was annealed to 770 K prior to CO exposure, the CO adsorption energy decreased significantly. STM measurements revealed that the Au particles grow upon annealing, but are not encapsulated by TiO_x suboxides. The higher CO adsorption energy observed for smaller Au coverages and before annealing is attributed to a significantly stronger interaction of CO with mono- and bilayer Au islands, while for higher particles, the adsorption energy becomes more bulk-like. The implications of these effects on the known particle size effects in CO oxidation over supported Au/TiO₂ catalysts are discussed.     

Sputter deposition of high transparent TiO2−xNx/TiO2/ZnO layers on glass for development of photocatalytic self-cleaning application

In this study, TiO_2−xN_x/TiO₂ double layers thin film was deposited on ZnO (80 nm thickness)/soda-lime glass substrate by a dc reactive magnetron sputtering. The TiO₂ film was deposited under different total gas pressures of 1 Pa, 2 Pa, and 4 Pa with constant oxygen flow rate of 0.8 sccm. Then, the deposition was continued with various nitrogen flow rates of 0.4, 0.8, and 1.2 sccm in constant total gas pressure of 4 Pa. Post annealing was performed on as-deposited films at various annealing temperatures of 400, 500, and 600 °C in air atmosphere to achieve films crystallinity. The structure and morphology of deposited films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and atomic force microscopy (AFM). The chemical composition of top layer doped by nitrogen was evaluated by X-ray photoelectron spectroscopy (XPS). Photocatalytic activity of samples was measured by degradation of Methylene Blue (MB) dye. The optical transmittance of the multilayer film was also measured using ultraviolet-visible light (UV-vis) spectrophotometer. The results showed that by nitrogen doping of a fraction (∼1/5) of TiO₂ film thickness, the optical transmittance of TiO_2−xN_x/TiO₂ film was compared with TiO₂ thin film. Deposited films showed also good photocatalytic and hydrophilicity activity at visible light.     

Photon-induced chemical vapor deposition of molybdenum on Pt(1 1 1)

Temperature-programmed desorption (TPD) and X-ray photoelectron spectroscopy (XPS) have been employed to study the adsorption and photon-induced decomposition of Mo(CO)₆. Mo(CO)₆ adsorbs molecularly on a Pt(1 1 1) surface with weak interaction at 100 K and desorbs intact at 210 K without undergoing thermal decomposition. Adsorbed Mo(CO)₆ undergoes decarbonylation to form surface Mo(CO)_x (x ? 5) under irradiation of ultraviolet light. The Mo(CO)_x species can release further CO ligands to form Mo adatoms with CO desorption at 285 K. In addition, a fraction of the released CO ligands transfers onto the Pt surface and subsequently desorbs at 350-550 K. The resulting Mo layer deposited on the Pt surface is nearly free of contamination by C and O. The deposited Mo adatoms can diffuse into the bulk Pt at temperatures above 1070 K.     

Thermal decomposition of Mo(CO)6 on thin Al2O3 film: A combinatorial investigation by XPS and UPS

A thin and homogeneous alumina film was prepared by deposition and oxidation of aluminum on a refractory Re(0 0 0 1) substrate under ultrahigh vacuum conditions. X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS) and high-resolution electron-energy-loss spectroscopy (HREELS) demonstrate that the oxide film is long-range ordered, essentially stoichiometric and free from surface hydroxyl groups. The chemisorption and thermal decomposition of Mo(CO)₆ on the Al₂O₃ film were investigated by means of XPS and UPS. Mo(CO)₆ adsorbs molecularly on the oxide film at 100 K; however, thermal decomposition of the adsorbate occurs upon annealing at high temperatures. Consequently the metallic molybdenum clusters are deposited on the thin alumina film via complete decarbonylation of Mo(CO)₆.     

Ultra-thin Si overlayers on the TiO2 (1 1 0)-(1 × 2) surface: Growth mode and electronic properties

The growth of thin subnanometric silicon films on TiO₂ (1 1 0)-(1 × 2) reconstructed surfaces at room temperature (RT) has been studied in situ by X-ray and ultra-violet photoelectron spectroscopies (XPS and UPS), Auger electron and electron-energy-loss spectroscopies (AES and ELS), quantitative low energy electron diffraction (LEED-IV), and scanning tunneling microscopy (STM). For Si coverage up to one monolayer, a heterogeneous layer is formed. Its composition consists of a mixture of different suboxides SiO_x (1 < x ? 2) on top of a further reduced TiO₂ surface. Upon Si coverage, the characteristic (1 × 2) LEED pattern from the substrate is completely attenuated, indicating absence of long-range order. Annealing the SiO_x overlayer results in the formation of suboxides with different stoichiometry. The LEED pattern recovers the characteristic TiO₂ (1 1 0)-(1 × 2) diagram. LEED I-V curves from both, substrate and overlayer, indicate the formation of nanometric sized SiO_x clusters.     

Hydroxylation-induced modifications of the Al2O3/NiAl(0 0 1) surface at low water vapour pressure

STM, STS, LEED and XPS data for crystalline θ-Al₂O₃ and non-crystalline Al₂O₃ ultra-thin films grown on NiAl(0 0 1) at 1025 K and exposed to water vapour at low pressure (1 × 10⁻⁷-1 × 10⁻⁵ mbar) and room temperature are reported. Water dissociation is observed at low pressure. This reactivity is assigned to the presence of a high density of coordinatively unsaturated cationic sites at the surface of the oxide film. The hydroxyl/hydroxide groups cannot be directly identify by their XPS binding energy, which is interpreted as resulting from the high BE positions of the oxide anions (O_1s signal at 532.5-532.8 eV). However the XPS intensities give evidence of an uptake of oxygen accompanied by an increase of the surface coverage by Al³⁺ cations, and a decrease of the concentration in metallic Al at the alloy interface. A value of ∼2 for the oxygen to aluminium ions surface concentration ratio indicates the formation of an oxy-hydroxide (AlO_xOH_y with x + y ∼ 2) hydroxylation product. STM and LEED show the amorphisation and roughening of the oxide film. At P(H₂O) = 1 × 10⁻⁷ mbar, only the surface of the oxide film is modified, with formation of nodules of ∼2 nm lateral size covering homogeneously the surface. STS shows that essentially the valence band is modified with an increase of the density of states at the band edge. With increasing pressure, hydroxylation is amplified, leading to an increased coverage of the alloy by oxy-hydroxide products and to the formation of larger nodules (∼7 nm) of amorphous oxy-hydroxide. Roughening and loss of the nanostructure indicate a propagation of the reaction that modifies the bulk structure of the oxide film. Amorphisation can be reverted to crystallization by annealing under UHV at 1025 K when the surface of the oxide film has been modified, but not when the bulk structure has been modified.     

Reduction of FeO/Pt(1 1 1) thin films by exposure to atomic hydrogen

Using scanning tunneling microscopy (STM), X-ray photoemission spectroscopy (XPS) and density functional theory (DFT) calculations we have studied the reduction of ultra-thin films of FeO(1 1 1) grown on Pt(1 1 1) after exposure to atomic hydrogen at room temperature. A number of new ordered, partly-reduced FeO_x structures are identified and as a general trend we reveal that all the reduced FeO_x structures incorporate 2-fold coordinated Fe atoms as opposed to the original 3-fold coordinated Fe atoms in the FeO film. We find that when all the Fe atoms are 2-fold O-coordinated the FeO_x surface structure is resistant to further reduction at room temperature. We observe that water easily dissociates on the most heavily reduced FeO_x, structure in contrast to the initially inert FeO film, and reveal that it is possible to partially re-oxidize the FeO_x film by heating the surface slightly in the presence of water.     

Aerosol-assisted flow synthesis of WxTi1−xO2 solid solution spheres with enhanced photocatalytic activity

In this paper, W_xTi_1−xO₂ solid solutions (x = 0.000, 0.005, 0.010, 0.015, and 0.020) microspheres were synthesized with an aerosol-assisted flow synthesis method. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen sorption, UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the as-prepared catalysts were measured by the degradation of rhodamine B (RhB) under visible light irradiation (λ ≥ 420 nm). All the solid solutions exhibited higher photocatalytic activities than pure TiO₂ and the W_0.015Ti_0.985O₂ solid solution possessed the highest photocatalytic activity. The degradation constant of RhB on W_0.015Ti_0.985O₂ solid solution catalyst was about 15 times of that of the pure TiO₂ and 25 times of that of Degussa P25, respectively. This study provides an effective method to prepare visible light photocatalysts on a large scale.     

Support effects on the nucleation, growth, and morphology of gold nano-clusters

The nucleation, growth, and morphology of gold (Au) clusters on an irreducible oxide (SiO₂), highly reduced TiO_x (x ∼ 1), and less reduced TiO_x (x ∼ 2) were investigated by scanning tunneling microscopy (STM) with the goal of understanding the relationship between the nucleation, growth, and morphology of Au clusters and the reducibility of the oxide support. Au clusters show preferential nucleation and growth on a TiO_x surface compared to a SiO₂ surface. In addition, higher densities of Au clusters were found on highly reduced TiO_x, suggesting that reduced Ti sites play a role as an active site for the nucleation and growth of Au clusters.     

Room and high-temperature scanning tunnelling microscopy and spectroscopy (HT-STM/STS) investigations of surface nanomodifications created on the TiO2(1 1 0) surface

High-temperature scanning tunnelling microscopy, scanning tunnelling spectroscopy and current imaging tunnelling spectroscopy (HT-STM/STS/CITS) were used to study the topographic and electronic structures changes due to surface modifications of the TiO₂(1 1 0) surface caused by the STM tip. In situ high-temperature STM results showed that the created modifications were stable even at elevated temperatures. The STS/CITS results showed the presence of energy gap below the Fermi level on the untreated regions. The disappearance of energy gap below the Fermi level on the modifications created by the tip was observed. It is assumed that the presence of the tip can change the chemical stoichiometry of the surface from TiO_2−x towards Ti₂O₃.     

Thickness dependence of the surface plasmon dispersion in ultrathin aluminum films on silicon

The collective excitation in Al films deposited on Si(1 1 1)-7 × 7 surface was investigated by high-resolution electron-energy-loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM). At the Al film thickness d < 10 ML, the surface plasmon of Al film has only a small contribution to the observed energy-loss peaks in the long wavelength limit (q_∥≈0), while its contribution becomes significant for q_∥>d^-1. More interestingly, for thin Al films, the initial slope of the surface plasmon dispersion curve is positive at q_∥∼0, in a sharp contrast to bulk Al surface where the energy dispersion is negative. These observations may be explained based on the screening interaction of the space charge region at the Al-Si interface.     

Growth mode and electronic structure of Au nano-clusters on NiO(0 0 1) and TiO2(1 1 0)

The growth mode and electronic structure of Au nano-clusters grown on NiO and TiO₂ were analyzed by reflection high-energy electron diffraction, a field-emission type scanning electron microscope, medium energy ion scattering and photoelectron spectroscopy. Au was deposited on clean NiO(0 0 1)-1 × 1 and TiO₂(1 1 0)-1 × 1 surfaces at room temperature with a Knudsen cell at a rate of 0.25-0.35 ML/min (1 ML = 1.39 × 10¹⁵ atoms/cm²:Au(1 1 1)). Initially two-dimensional (2D) islands with thickness of one Au-atom layer grow epitaxially on NiO(0 0 1) and then neighboring 2D-islands link each other to form three-dimensional (3D)-islands with the c-axis oriented to the [1 1 1] direction. The critical size to form 3D-islands is estimated to be about 5 nm². The shape of the 3D-islands is well approximated by a partial sphere with a diameter d and height h ranging from 2.0 to 11.8 nm and from 0.95 to 4.2 nm, respectively for Au coverage from 0.13 to 4.6 ML. The valence band spectra show that the Au/NiO and Au/TiO₂ surfaces have metallic characters for Au coverage above 0.9 ML. We observed Au 4f spectra and found no binding energy shift for Au/NiO but significant higher binding energy shifts for Au/TiO₂ due to an electron charge transfer from Au to TiO₂. The work function of Au/NiO(0 0 1) gradually increases with increase in Au coverage from 4.4 eV (NiO(0 0 1)) to 5.36 eV (Au(1 1 1)). In contrast, a small Au deposition(0.15 to 1.5 ML) on TiO₂(1 1 0) leads to reduction of the work function, which is correlated with an electron charge transfer from Au to TiO₂ substrate.     

Composition depth profiles of Bi3.15Nd0.85Ti3O12 thin films studied by X-ray photoelectron spectroscopy

In the present work, X-ray photoelectron spectroscopy (XPS) was used to investigate the composition depth profiles of Bi_3.15Nd_0.85Ti₃O₁₂ (BNT) ferroelectric thin film, which was prepared on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD). It is shown that there are three distinct regions formed in BNT film, which are surface layer, bulk film and interface layer. The surface of film is found to consist of one outermost Bi-rich region. High resolution spectra of the O 1s peak in the surface can be decomposed into two components of metallic oxide oxygen and surface adsorbed oxygen. The distribution of component elements is nearly uniform within the bulk film. In the bulk film, high resolution XPS spectra of O 1s, Bi 4f, Nd 3d, Ti 2p are in agreement with the element chemical states of the BNT system. The interfacial layer is formed through the interdiffusion between the BNT film and Pt electrode. In addition, the Ar⁺-ion sputtering changes lots of Bi³⁺ ions into Bi⁰ due to weak Bi-O bond and high etching energy.     

Photooxidation of different organic dyes (RB, MO, TB, and BG) using Fe(III)-doped TiO2 nanophotocatalyst prepared by novel chemical method

The nano-structured Fe(III)-doped TiO₂ photocatalysts with anatase phase have been developed for the oxidation of non-biodegradable different organic dyes like methyl orange (MO), rhodamine B (RB), thymol blue (TB) and bromocresol green (BG) using UV-Hg-lamp. The different compositions of Fe_xTi_1−xO₂ (x = 0.005, 0.01, 0.05, and 0.1) nanocatalysts synthesized by chemical method (CM), have been characterized by X-ray diffraction (XRD), UV-vis diffuse reflectance spectra, specific surface area (BET), transmission electronic microscopy (TEM) analysis, XPS, ESR and zeta potential. From XRD analysis, the results indicate that all the compositions of Fe(III) doped in TiO₂ catalysts gives only anatase phase not rutile phase. For complete degradation of all the solutions of the dyes (MO, RB, TB, and BG), the composition with x = 0.005 is more photoactive compared all other compositions of Fe_xTi_1−xO₂, and degussa P25. The decolorization rate of different dyes decreases as Fe(III) concentration in TiO₂ increases. The energy band gap of Fe(III)-doped TiO₂ is found to be 2.38 eV. The oxidation state of iron has been found to be 3+ from XPS and ESR show that Fe³⁺ is in low spin state.     

Characterization of TiO2/Au/TiO2 films deposited by magnetron sputtering on polycarbonate substrates

Transparent and conducting TiO₂/Au/TiO₂ (TAuT) films were deposited by reactive magnetron sputtering on polycarbonate substrates to investigate the effect of the Au interlayer on the optical, electrical, and structural properties of the films. In TAuT films, the Au interlayer thickness was kept at 5 nm. Although total thickness was maintained at 100 nm, the stack structure was varied as 50/5/45, 70/5/25, and 90/5/5 nm.In XRD pattern, the intermediate Au films were crystallized, while all TAuT films did not show any diffraction peaks for TiO₂ films with regardless of stack structure. The optical and electrical properties were dependent on the stack structure of the films. The lowest sheet resistance of 23 Ω/□ and highest optical transmittance of 76% at 550 nm were obtained from TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films. The work function was dependent on the film stack. The highest work function (4.8 eV) was observed with the TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm film stack. The TAuT film stack of TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films is an optimized stack that may be an alternative candidate for transparent electrodes in flat panel displays.     

Deposition and fabrication of alkanethiolate gold nanocluster films on TiO2(1 1 0) and the effects of plasma etching

Deposition and fabrication of films of Au nanoclusters protected by alkanethiolate ligands are attempted on a TiO₂(1 1 0) surface and the structures of films are observed by a scanning tunneling microscope (STM). Effects of oxygen and hydrogen-plasma etching in addition to UV irradiation on the structure and chemical composition of the films are also investigated by using STM and X-ray photoelectron spectroscopy. Alkanethiolate Au nanoclusters are produced using a modified Brust synthesis method and their LB films are dip-coated on TiO₂(1 1 0). Alkanethiolate Au nanoclusters are weakly bound to the substrate and can be manipulated with an STM tip. Net-like structures of alkanethiolate Au nanoclusters are formed by a strong blast of air. Oxygen-plasma etching removes alkanethiolate ligands and simultaneously oxidizes Au clusters. At room temperature, prolonged oxygen-plasma etching causes agglomeration of Au nanoclusters. UV irradiation removes ligands partly, which makes Au nanoclusters less mobile. The net-like structure of alkanethiolate Au clusters produced by a blast of air is retained after oxygen and hydrogen-plasma etching.     

Visible-light photocatalytic activity of nitrogen-doped TiO2 thin film prepared by pulsed laser deposition

Nitrogen-doped titanium dioxide (TiO_2−xN_x) thin films have been prepared by pulse laser deposition on quartz glass substrates by ablated titanium dioxide (rutile) target in nitrogen atmosphere. The x value (nitrogen concentration) is 0.567 as determined by X-ray photoelectron spectroscopy measurements. UV-vis spectroscopy measurements revealed two characteristic deep levels located at 1.0 and 2.5 eV below the conduction band. The 1.0 eV level is attributable to the O vacancy state and the 2.5 eV level is introduced by N doping, which contributes to narrowing the band-gap by mixing with the O2p valence band. The enhanced degradation efficiency in a broad visible-light range was observed from the degradation of methylene blue and methylene orange by the TiO_2−xN_x film.     

Model NSR catalysts: Fabrication and reactivity of barium oxide layers on Cu(1 1 1)

The growth of barium oxide on a Cu(1 1 1) substrate, formed by the deposition of barium and its subsequent oxidation, yields stable BaO films which expose predominantly the BaO(1 0 0) surface. The interaction of the oxide films with common components of motor-vehicle exhaust gases (CO₂, H₂O, NO_x) has been studied using surface analytical techniques, including X-ray photoelectron spectroscopy (XPS), temperature programmed desorption (TPD) and reflection IR spectroscopy (RAIRS). The spectroscopic identification of Ba(OH)₂, BaCO₃ and Ba(NO₂)₂ phases is discussed, and the relative stabilities and decomposition mechanisms of these materials when supported on Cu(1 1 1) is revealed by a combination of TPD and XPS. BaO is shown to be resistant to reaction with pure NO and NO/O₂ mixtures, but exposure to NO₂ leads to the rapid formation of barium nitrite. The formation of the nitrite is proposed to be the first-step in the production of barium nitrate, which has previously been shown to be the main phase involved in NO_x storage and reduction (NSR) catalysis.     

Preparation, characterization and photocatalytic performance of TiO2/CexZr1−xO2 toward the oxidation of gaseous benzene

Increasing environmental pollution caused by the volatile organic compounds due to their toxicity makes their removal imperative. So it is crucial to develop processes which can degrade these compounds effectively. The paper demonstrates that the photocatalytic activity of TiO₂ toward the decomposition of gaseous benzene in a batch reactor can be greatly enhanced by loading TiO₂ onto the surface of Ce_xZr_1−xO₂ (x ≥ 0.25) using sol-gel technology. This research investigated the relationship between x amount and the photocatalytic activity of TiO₂. The prepared photocatalysts were characterized by BET, XRD, UV-vis diffuse reflectance and XPS analyses. The specific surface area of photocatalyst decreases as x decreases. XRD results reveal the no peaks of titania were detected. Among the five catalysts prepared, only the binding energy values of Ti2p_3/2 of TiO₂/Ce_0.5Zr_0.5O₂ shift toward lower value. The order of photocatalytic activity is TiO₂/Ce_0.5Zr_0.5O₂ > TiO₂/Ce_0.75Zr_0.25O₂ > TiO₂/CeO₂ ≈ TiO₂/Ce_0.25Zr_0.75O₂ > TiO₂/ZrO₂ ≈ TiO₂. The mechanism role of Ceria-Zirconia mixed oxides in photocatalytic reaction was speculated.     

Deposition dynamics and chemical properties of size-selected Ir clusters on TiO2

We report a study of Ir_n/TiO₂ samples prepared by size and energy-selected deposition of Ir_n⁺ (n=1, 2, 5, 10, 15) on rutile TiO₂(1 1 0) at room temperatures. The Ir clusters are found to be formally in the zero oxidation state, and there are no significant shifts in Ir 4f binding energy with cluster size. Over a wide range of impact energies, both Ir XPS intensity and peak position are constant, indicating constant sticking coefficient, and no impact-driven redox chemistry. Low energy ion scattering spectroscopy (ISS) suggests that the deposited Ir clusters remain largely intact, neither fragmenting nor agglomerating, and retaining 3-D structures for the larger sizes. For impact energies above 10 eV/atom, comparison of ISS and XPS data show that the Ir clusters are penetrating into the TiO₂ surface, with the extent of penetration increasing with both per atom energy and cluster size. Temperature programmed desorption (TPD) of CO is used to further characterize the deposited Ir_n. This system shows pronounced substrate-mediated adsorption (SMA) in low CO exposures, with strong dependence on cluster size. ISS and sputtering experiments indicate that CO adsorbed via SMA is bound differently than CO adsorbed in high dose experiments. In experiments with sequential C¹⁶O and C¹⁸O doses, facile C¹⁶O → C¹⁸O exchange is observed for Ir₅ and larger clusters, but not for Ir₂. The peak CO desorption temperature is found to decrease with cluster size. The cycle of CO adsorption and heating comprising a TPD experiment have a dramatic effect on the sample morphology, leading to encapsulation of Ir by a thin TiO_x layer.