Production of Cs and Fr isotopes from a high-density UC targets with different grain dimensions

A UC target material of 11.3±0.5 g/cm^3 uranium density with the grain size of 20 and 5μm manufactured in a form of pills by the method of powder metallurgy has been tested on-line within the temperature range of 1800-2100 ^° C . The mass of uranium exposed to the beam was 4-7g. The yields and release rates of Cs and Fr isotopes produced by fission and spallation reactions of ²³⁸U by 1GeV protons have been measured. The yields of Cs and Fr isotopes obtained from the tested target materials have been compared, including yields of very short-lived Fr isotopes with half-lives down to 1ms. Temperature-resistant materials (porous graphite and tantalum foil) have been used for the internal-container construction, which holds the UC target pills inside a tungsten external container heated by the resistant heating. The fastest release and the highest efficiency for short-lived isotopes have been obtained for the targets with the internal container manufactured from the tantalum foil. Results of on-line tests of a big mass target (730g of 5μm grain UC target material) have been discussed.     

On-line production of Rb and Cs isotopes from uranium carbide targets

A series of on-line mass separation experiments have been performed at the IRIS facility to measure the yield and release of Rb and Cs neutron-rich isotopes produced by fission reaction of ²³⁸U. A 1 GeV proton beam was used to bombard uranium carbide targets with the densities of 11 g/cm³ and 1.5 g/cm³ held at temperatures in the range (2000-2230) ^°C. The release curves of Rb and Cs long-lived isotopes were measured from both kinds of targets. The overall production efficiency was determined making use of experimentally measured cross-sections of that isotope production. Comparison of the experimental yields of Rb and Cs isotopes with the calculated ones after corrections for losses due to finite release times suggests that the diffusion is the dominating process reducing the efficiency for short-lived isotopes. When normalized to the same thickness, an enhancement for the high-density rod target of the measured isotope yields is observed when going far from stability. This is possibly explained by the reactions induced by secondary neutrons. A significant odd-even effect with higher yields of Cs even neutron isotopes has been observed, confirming a similar effect obtained in earlier experiments.     

On-line production of neutron rich isotopes from uranium carbide targets

Experiments done using on-line mass separation of neutron-rich nuclei produced by 1 GeV proton beam on natural U by spallation reactions are performed to study the characteristics of different UCx targets. Special attention is devoted to reliably extract isotopic yields in case of complex decay schemes and to the valuation of release efficiency of some isotopic chains. New gamma-branching measuremet for ⁹²Rb are obtained. In addition, a formalism is developed to disantangle the contribution of β-decay in the target from direct production by fission and to provide more consistent data for the interpretation of release curves. Some results are shown for the Cs and Rb isotopic chains.     

Sputtering yield of chromium by argon and xenon ions with energies from 50 to 500 eV

A radioactive tracer technique is described for the quantitative measurement of the sputtering yield of a target material electroplated on a copper substrate. Sputtering yields of chromium by argon and xenon ions with energies from 50 to 500 eV are reported. The ion beams, having a current density ranging from 0.01 to 0.1 mA/cm² at an operating pressure of 2×10^–5 Torr, were produced by a low-energy ion gun. The sputtered atoms were collected on an aluminum foil surrounding the target. ⁵¹Cr was used as the tracer isotope. The results indicate that the radioactive tracer technique is sensitive enough in measuring the extremely small amount of sputtered material at low ion currents and low ion energies.     

Integrated target-ion source unit for on-line production of radioactive short-lived isotopes

A new version of integrated target-ion source unit (ionising target) has been developed for the on-line production of radioactive single-charged ions. The target is able to withstand temperatures up to 2500 ^°C and acts also as an ion source of the surface and laser ionisation. Off-line and on-line experiments with the ionising target, housing tantalum foils as a target material, have been carried out at the IRIS (Investigation of Radioactive Isotopes on Synchrocyclotron) facility. The off-line surface ionisation efficiency measured for stable atoms of Li, Rb and Cs was correspondingly 6% , 40% and 55% at the target temperature of 2000 ^°C and 3-10% for atoms of rare-earth elements Sm, Eu, Tm and Yb at a temperature of 2200 ^°C. The off-line measured values of the ionisation efficiency for stable Gd and Eu atoms by the laser beam ionisation inside the target were 1% and 7%, respectively. The radioactive beam intensities of neutron-deficient rare-earth nuclides from Eu to Lu produced by the integrated target-ion source unit have been measured at a temperature of 2500 ^°C. The results of the integrated target-ion source unit use for on-line laser resonance ionisation spectroscopy study of neutron-deficient Gd isotopes have been also presented.     

Beta-decay energies and masses of short-lived isotopes of rubidium,caesium, francium,and radium

Total decay energies have been measured for a number of neutron-deficient Rb and Cs isotopes, as well as for some neutron-rich isotopes of Fr and Ra. Mass separated sources were produced at the ISOLDE on-line separator at CERN. By applying two differentβ-γ coincidence methods,Q values or their lower limits were determined for^76–78Rb,⁸⁰Rb,^121–124Cs,²²²Fr,^224–226Fr,²²⁹Ra-²²⁹Ac. For many of these nuclei, the atomic mass excesses could be derived, allowing the comparison of masses of far unstable nuclei with predictions from mass formulae. The odd-odd nuclei⁷⁶Rb and⁷⁸Rb appear to be 1?1 1/2 MeV more strongly bound than expected from the systematics.     

Francium sources and traps for fundamental interaction studies

Francium is one of the best candidates for atomic parity nonconservation (APNC) and for the search of permanent electric dipole moments (EDMs). APNC measurements test the weak force between electrons and nucleons at very low momentum transfers. They also represent a unique way to detect weak nucleon-nucleon interactions. EDMs are instead related to the time-reversal symmetry. Preliminary to these fundamental measurements are precision studies in atomic spectroscopy and the development of magneto-optical traps (MOT), which partially compensate for the lack of stable Fr isotopes. At LNL Legnaro, francium is produced by fusion of 100-MeV ¹⁸O with ¹⁹⁷Au in a thick target, followed by evaporation of neutrons from the compound nucleus. Francium diffuses inside the hot target (1200 K) and is surface ionized for injection at 3 keV in an electrostatic beamline. Typically, we produce 1×10⁶ (²¹⁰Fr ions)/s for a primary flux of 1.5×10¹² particles/s. We have studied Fr yields as a function of primary beam energy, intensity, and target temperature. Information on the efficiency of bulk diffusion, surface desorption and ionization is deduced. The beam then enters a Dryfilm-coated cell, where it is neutralized on a heated yttrium plate. The escape time of neutral Fr (diffusion + desorption) is approximately 20 s at 950 K, as measured with a dedicated setup. In the MOT, we use 6 orthogonal Ti:sapphire laser beams for the main pumping transition and 6 beams from a stabilized diode repumper. Fluorescence from trapped atoms is observed with a cooled CCD camera, in order to reach noise levels from stray light equivalent to approximately 50 atoms. Systematic tests are being done to improve the trapping efficiency. We plan to further develop Fr traps at LNL; in parallel, we will study APNC and EDM techniques and systematics with stable alkalis at Pisa, Siena, and Ferrara.     

Chiral three-nucleon forces and bound excited states in neutron-rich oxygen isotopes

Astatine isotopes can be produced in liquid lead-bismuth eutectic targets through proton-induced double charge exchange reactions on bismuth or in secondary helium-induced interactions. Models implemented into the most common high-energy transport codes generally have difficulties to correctly estimate their production yields as was shown recently by the ISOLDE Collaboration, which measured release rates from a lead-bismuth target irradiated by 1.4 and 1 GeV protons. In this paper, we first study the capability of the new version of the Liège intranuclear cascade model, INCL4.6, coupled to the deexcitation code ABLA07 to predict the different elementary reactions involved in the production of such isotopes through a detailed comparison of the model with the available experimental data from the literature. Although a few remaining deficiencies are identified, very satisfactory results are found, thanks in particular to improvements brought recently on the treatment of low-energy helium-induced reactions. The implementation of the models into MCNPX allows identifying the respective contributions of the different possible reaction channels in the ISOLDE case. Finally, the full simulation of the ISOLDE experiment is performed, taking into account the likely rather long diffusion time from the target, and compared with the measured diffusion rates for the different astatine isotopes, at the two studied energies, 1.4 and 1 GeV. The shape of the isotopic distribution is perfectly reproduced as well as the absolute release rates, assuming in the calculation a diffusion time between 5 and 10hours. This work finally shows that our model, thanks to the attention paid to the emission of high-energy clusters and to low-energy cluster induced reactions, can be safely used within MCNPX to predict isotopes with a charge larger than that of the target by two units in spallation targets, and, probably, more generally to isotopes created in secondary reactions induced by composite particles.     

Target mass correction on the 3He polarized structure function

The diffusion-effusion model has been used to analyse the release and yields of Fr and Cs isotopes from uranium carbide targets of very different thicknesses (6.3 and 148 g/cm²) bombarded by a 1 GeV proton beam. Release curves of several isotopes of the same element and production efficiency versus decay half-life are well fitted with the same set of parameters. Comparison of efficiencies for neutron-rich and neutron-deficient Cs isotopes enables separation of the contributions from the primary (p + ²³⁸U) and secondary (n + ²³⁸U) reactions to the production of neutron-rich Cs isotopes. A rather simple calculation of the neutron contribution describes these data fairly well. The FLUKA code describes the primary and secondary-reaction contributions to the Cs isotopes production efficiencies for different targets quite well.     

Calculation of production and decay of radioisotopes for future irradiation experiments and ion beam facilities

The design of future radioactive ion beam (RIB) facilites requires the forecast of radio isotope inventory after irradiation. At CERN – ISOLDE, we developed a software that estimates the activity of irradiated materials as a function of time dedicated to radioactive waste management. This tool can also be used for licensing procedures, planning of irradiation experiments and the estimation of yields.     

Target-ion source unit ionization efficiency measurement by a method of stable ion beam implantation

At the IRIS facility a rather precise method of the target-ion source unit ionization efficiency measurement has been developed. The method exploits an off-line mass-separator for the implantation of the ion beams of selected stable isotopes into a tantalum foil placed inside a Faraday cup in the focal plane of the mass-separator. After the implantation of the required amount of the investigated species, tantalum foil has been inserted into the volume of the target-ion source unit prepared for the on-line utilization at the IRIS on-line separator. The first tests have ensured the ionization efficiency values (90±10)% for Rb and (85±10)% for Cs in the empty combined target-ion source unit, which was used as a reference one. For the target-ion source unit with UC target material inside the measured value of the ionization efficiency of Rb was (52±20)%.     

Release time calculations for the SPES direct UCx target

A Direct Target for a mid-term RIB ISOL-type facility is being developed at LNL, in the framework of the R&D for the SPES project [1]. Using a 40 MeV proton beam impinging on a UCx thick target of 2.5 g/cm³ density, a production rate of 10¹³ in target fissions per second is expected [2]. The crucial point, when short-lived isotopes are produced in the target, is to build systems (target + ion source) with good release properties and high efficiency. Monte Carlo simulations were performed using the GEANT4 toolkit [3] and the RIBO code [4] in order to optimize our target geometry and to estimate the average release time.     

ISOL beams of hafnium isotopes and isomers

The production of ISOL beams of hafnium is described. Radioactive Hf isotopes were produced at ISOLDE by 1.4 GeV proton-induced spallation in Ta and W foils. Chemical evaporation in form of HfF₄ and mass separation in the molecular sideband HfF₃⁺ after electron impact ionization provided intense and pure beams. Beams of ^158-185Hf and short-lived isomers down to 1.1 s ^177mHf were observed, but the method could be extended to reach even more exotic isotopes: down to about ¹⁵⁴Hf (N=82) on the neutron-deficient side and up to neutron-rich ¹⁸⁸Hf.     

(Im-)possible ISOL beams

Refractory elements, i.e. elements with very high melting point and low vapor pressure, cannot be released in atomic form from an ISOL target. Therefore most of these elements are presently not available as ISOL beams. However, when reactive gases are introduced into the target, they may form volatile compounds with the refractory elements, allowing for an easier transport to the ion source. Particularly useful are high-temperature stable fluorides and oxides. By these chemical evaporation methods so far ISOL beams of the refractory elements C, Zr, Hf and Ta have been produced. We discuss how ISOL beams of B, Ti, Nb, Mo, Tc, Ru, W, Re, Os and Ir could be produced in a similar way.     

Mössbauer spectroscopy at ISOLDE

Applications of radioactive ion beams produced at the ISOLDE facility for Mössbauer studies of probe atoms in solids are presented. Examples are given for a site-selective incorporation on different substitutional sites in compound semiconductors by ion implantation and thermal annealing of the radiation damage resulting from the implantation. The interactions of the probe atoms with lattice defects created in the implantation process have been studied to elucidate likely causes for the site-selective implantation mechanism. The technique has enabled to determine the electronic densities at electrically active substitutional probe atoms, having shallow donor or acceptor states as well as states deeper in the band gap. The results are in good agreement with theoretical results from local density calculations. Methodological aspects of the Mössbauer emission techniques employed at ISOLDE are compared to alternative accelerator based techniques and the consequences of the application of different precursor isotopes to the ⁵⁷Fe Mössbauer isotope are treated in detail for ⁵⁷Fe in silicon. Finally, results obtained for the magnetic hyperfine interactions of 5 sp impurities associated with vacancies in ferromagnetic metals are discussed.     

Atomic probes of electromagnetic and weak interactions with trapped radioactive atoms

The alkali element francium has a simple electronic structure, and copious amounts of a wide range of isotopes can be produced in present and future rare isotope facilities. The atomic parity violating weak interaction in Fr is 18 times larger than in Cs, which makes it one of the best candidates to search for the effects of the weak interaction and its isotopic dependence. Atomic trapping methods now offer new ways to study these atoms with precision, and we will discuss some of our recent measurements with trapped Fr atoms. Future measurements of the spin-independent weak interaction can be used to test the standard model, but advances in atomic theory and improved understanding of the neutron distribution in nuclei are needed to make progress. We have made precise hyperfine-anomaly measurements in Fr and have shown that they are sensitive to the radial distribution of the neutron magnetization. Measurements of this type can help to constrain the neutron distributions. Future measurements of the spin-dependent weak interaction should allow extraction of the nuclear anapole moments for a sequence of isotopes, and allow separation of the neutron and proton weak interactions between hadrons. Received: 1 May 2001 / Accepted: 4 December 2001     

Coulomb excitation of neutron-rich 138,140,142Xe at REX-ISOLDE

We report on “safe” Coulomb excitation of neutron-rich ^138,140,142Xe nuclei. The radioactive nuclei have been produced by ISOLDE at CERN and post-accelerated by the REX-ISOLDE facility. The γ-rays emitted by the decay of excited states have been detected by the MINIBALL array. Recent results are presented.     

High-accuracy mass determination of unstable cesium and barium isotopes

Direct mass measurements of short-lived Cs and Ba isotopes have been performed with the tandem Penning trap mass spectrometer ISOLTRAP installed at the on-line isotope separator ISOLDE at CERN. Typically, a mass resolving power of 600 000 and an accuracy of δm ≈ 13 keV have been obtained. The masses of ^123,124,126Ba and ^122mCs were measured for the first time. A least-squares adjustment has been performed and the experimental masses are compared with theoretical ones, particularly in the frame of a macroscopic-microscopic model.     

Multifoil UCx target for the SPES project --An update

The target system is one of the key issues for the facilities aimed at the production of neutron-rich radioactive ion beams. In the framework of the SPES project (Study for the Production of Exotic Species), the possibility of using a target configuration with a proton beam (40MeV, 0.2mA) directly impinging on multiple uranium carbide disks is investigated. The ²³⁸U fission fragments constitute the source for the exotic beams and for this purpose the disks are placed inside a graphite box at 2000 ^°C. The target is split into several thin disks in order to allow the cooling of the system by thermal radiation. In this way about ∼ 10¹³ fissions s ^-1 are obtained with a relative simple system and with relative low costs. Further steps have been performed compared to previous publications and now all the main parameters of the system have been analysed by means of calculation codes: the fission rates and the fission fragment distribution; the power deposition and the thermal analysis; the thermo-mechanical behaviours of the disks; the effusive and diffusive extraction release properties of the target.     

Target ion source and charge exchange cell development for the EXCYT facility

The EXCYT facility at the INFN-LNS is based on a K-800 superconducting cyclotron delivering stable ion beams on a Target Ion Source (TIS) assembly to produce the required nuclear species, and on a 15 MV Tandem for post-accelerating the radioactive beams. For some ion beams such as for Li, the extraction efficiency from the TIS is higher when obtained by positive ionisation, while the injection into the Tandem is possible only after a charge exchange to obtain negative ions. In this work we present the procedures together with the results of the production of ^6,7,8,9Li beams extracted at EXCYT during the last year. The production of the radioactive elements was performed by sending a ¹³C⁴⁺ primary beam of 45 MeV/u on a graphite target. The ionisation of the production species was achieved by a tungsten positive surface ioniser. The Li⁺ has been extracted from TIS at different energies to cross-check the transmission and the charge exchange efficiency. To perform the conversion from positive to negative ions we employed a Charge Exchange Cell (CEC) containing Cs vapours. The Li beam interacts with the latter in a two-step reaction, thus converting its charge from +1 to –1. The CEC was already characterised during off-line tests; the results obtained at EXCYT confirmed both the isotopic shift effect and the efficiency values at several given extraction energies. Future improvements of the TIS and the CEC are discussed.