哌啶氧铵盐对醇氧化反应的活性和选择性

系统地研究了12种具有不同4-位取代基(R=H、CH~3O、Cl)及反离子(X=Cl、BF~4、ClO~4、Br或Br~3)的2, 2, 6, 6-四甲基哌啶氧铵盐对醇的氧化反应, 发现这些氧铵盐都能以很高的由率将一级醇氧化为醛, 二级醇氧化为酮。氧化反应的活性与4-位取代基及反离子有关。当反离子相同时, 反应活性的顺序为Cl>CH~3O>H;当4-位取代基相同时, 反应活性的顺序为Cl^-》BF~4^->ClO~4^->Br^-。氧化反应的选择性主要与反离子有关, 当反离子为Cl^-时, 主要氧化一级醇; 当反离子为BF~4^-、ClO~4^-、Br^-或Br~3^-时, 主要氧化二级醇。     

硫化聚并苯导电材料结构的理论化学研究

采用量子化学从头算方法和AM1半经验方法,探讨了聚并苯导电聚合物硫掺杂前后结构和电子性质的变化,提出了硫化聚并苯导电材料的“双层夹心”分子结构模型.研究表明,硫化后的聚并苯材料,S原子位于两层聚并苯分子平面中间,并与两个聚并苯分子平面中相应的两个C原子相键合,形成C—S—C“桥式”共价单键;并解释了硫化聚并苯导电材料比本征态聚并苯材料作电极时可逆容量增大的原因.     

锂/聚噻吩体系的动力学模型

本文运用STM及SEM确定处理固相离子传导的基体形状为球形; 用改进的GITT方法(间隙库仑滴定法)计算了离子的扩散系数, 在10^-^1^0~10^-^1^2cm^2.s^-^1量级; 运用XPS方法证明了界面的部分电荷转移。建立了阴离子(ClO~4^-)在导电聚合物(聚噻吩)中的电化学嵌入反应的动力学表达式。将上述模型应用于ClO~4^-在聚噻吩(PT)中的嵌入反应。所得结果表明, 在脱嵌态聚噻吩的交换电流很小, 与它的半导体性质一致。同时, α+β<1, 再次证明了界面的部分电荷转移。     

聚并苯的链间作用对其导电能力的影响

采用量子化学晶体轨道ＣＮＤＯ／ ２ 方法,在考虑聚并苯链间作用的基础上对聚并苯双链模型的电子结构进行计算和讨论．结果表明：聚并苯链处于不同相对位置的链间作用对聚并苯的电荷分布规律及能带结构均有一定影响,位置不同,影响不同．从聚并苯的能带结构可以得出：聚并苯是有较小能隙、良好本征导电性能的半导体材料,考虑链间作用,对能带结构特征未有大的改变,能隙等值略有修正,导电能力有所加强．利用此模型讨论,更接近于晶体的真实结构,对进行聚并苯导电材料的性能改进将有一定帮助．     

聚并苯和聚并吡啶类化合物非线性光学性质及其分子材料设计

选取聚并苯、聚并吡啶和聚并吡嗪的 3种共振结构为基体 ,计算不同共轭单体齐聚物的结构及被取代后的聚合物二阶和三阶非线性光学系数 .结果表明 ,聚合物的二阶非线性光学系数与其单体相比有显著增大 ,被—NH2 和 NO2 取代后的聚并苯、聚并吡啶和聚并吡嗪的非线性光学系数又在聚合物的基础上进一步大幅度增加 ,有的增加 2～ 3个数量级 .在非取代的聚合物中 ,聚吡啶各种结构的二阶非线性光学系数均较大 ;取代聚合物中 ,单—NH2 和—NO2 取代的聚并苯 ,尤其是反式共振结构聚并苯的二位— NH2 和五位—NO2 取代结构的聚合物二阶非线性光学系数高达 3 .2 7× 1 0 - 2 7esu,说明这种— NH2 和 -NO2 取代后的聚并苯是一种很好的非线性光学材料 .     

甾醇TMS衍生物EI源质谱规律研究

甾醇是广泛存在于动植物界的一类重要天然产物.海洋微藻中C3羟基甾醇的结构多样主要体现在4位有无甲基存在,甾核上的双键数目和位置,侧链上的双键位置及侧链上烷基化程度和位置.早在60年代就有关于甾醇乙酸酯质谱特殊碎片的报道[1-4].     

V2O5/SiO2催化剂的异丁烷选择氧化反应性能

 采用溶胶－凝胶法和浸渍法制备了V2O5／SiO2催化剂,并用XRD,IR,TPD和活性评价等手段对催化剂的表面构造、化学吸附性能和异丁烷选择氧化反应性能进行了研究．结果表明：催化剂表面由Lewis碱位V＝O双键的端氧和Lewis酸位V5＋构成,异丁烷分子主要通过甲基中的H双位吸附在催化剂表面的Lewis碱位上,异丁烯分子可通过甲基的H吸附在催化剂表面的Lewis碱位,也可通过C＝C双键吸附在催化剂表面的Lewis酸位上．在常压条件下,异丁烷选择氧化产物主要有异丁烯、甲基丙烯醛和甲基丙烯酸,其中深度氧化产物CO2主要由通过C＝C吸附的异丁烯继续反应生成．     

HZSM-5分子筛上乙基叔丁基醚合成反应的理论研究

采用ONIOM (B3LYP/6-31G(d,p):UFF)分层计算的方法, 研究了HZSM-5 分子筛上乙醇和异丁烯合成乙基叔丁基醚(ETBE)的反应机理. 通过反应物在HZSM-5 分子筛上吸附性质的研究发现, 乙醇与分子筛酸性位相互作用形成氢键, 而异丁烯则作用在Brönsted 酸位上形成π配位吸附. 确定反应物吸附位置后, 进一步探索反应机理, 结果表明: HZSM-5分子筛上乙醇和异丁烯合成乙基叔丁基醚的反应为协同反应, 并且, 反应物吸附顺序的不同对反应过程存在一定的影响. ETBE合成反应的最优途径以反应物同时吸附形成的复合物作为起点. 在反应过程中, 形成π配位的H原子向异丁烯分子中不饱和双键的端位C原子靠近, 被吸附的乙醇分子中的O原子向异丁烯双键中的另一个C原子靠近, 直到形成C－O键, 生成ETBE. 这一过程中, 原有的质子H加成到异丁烯的端基C上形成C－H键, 而原醇羟基中的H和B酸位附近的O原子作用形成新的酸性位. 相应的协同反应的最低的反应势垒为25.14 kJ·mol^-1.     

聚乙烯/聚并苯复合材料室温电阻率变化规律研究

以新型导电材料聚并苯替代碳黑作为导电填料制备聚乙烯/聚并苯复合物.确定了复合物渗流转变区,并解释渗流转变现象的产生机理.从聚并苯含量和热处理过程,对聚乙烯/聚并苯复合物室温电阻率变化规律进行讨论.结果表明,聚并苯质量分数在20%～40%之间是聚乙烯/聚并苯复合物渗流转变区;热处理有利于聚乙烯晶区完善排列,也有利于导电链形成;以聚并苯作为导电填料所制备的复合物具有较高的PTC强度;辐射交联可以提高聚乙烯/聚并苯复合物PTC强度,抑制NTC效应.     

2-甲基喹 淋与Cu(ClO~4)~2和Cu(BF~4)~2生成配合物的结构研究

以2-甲基喹 啉为配体合成了五种含有阴离子ClO~4^-或BF~4^-的铜(II)配合物, 利用元素分析、红外光谱、电子光谱、电导、热重谱、ESR谱及变温磁化率的测定推测了配合物的结构, 提出双核铜配合物中含有直线型单氧桥Cu(II)-O-Cu(II)键的可能构型。     

A density functional study of C1-C4 alkyl adsorption on Cu(111)

To better understand the nature of alkyl intermediates often invoked in reactions involving hydrocarbon reactants and products, the adsorption of linear and branched C(1)-C(4) alkyls on Cu(111) at 1/4 ML and 1/9 ML coverages was studied using density functional theory. The adsorption energy and site preference are found to be coverage-dependent, and both direct alkyl-alkyl interactions and changes in the Cu electronic structure play a role in these trends. It was found that methyl strongly prefers the hollow sites, the branched alkyls strongly prefer the top site, and the linear C(2)-C(4) alkyls have weak site preferences that change with coverage. To explain these differences, rationalize alkyl adsorption trends, and predict the binding energy of other alkyls, a simple model was developed in which the binding energy is fit as a linear function of the number of C-Cu and C-H-Cu interactions as well as the C-H bond energy in the corresponding alkane. Site preference can be understood as a compromise between C-Cu interactions and C-H-Cu interactions. Density of states analysis was used to gain a molecular-orbital understanding of the bonding of alkyls to Cu(111).     

应用理论计算研究MCM-22分子筛相邻酸性位上乙烯和苯的吸附

应用ONIOM计算方法研究了MCM-22分子筛超笼12元环上存在两个酸性位时的酸强度及其与骨架铝之间距离的关系,并研究了乙烯和苯分子吸附的规律.计算采用52T簇模型和B3LYP/6-31G**/MNDO方法.结果表明,存在两个酸性位且两个骨架铝之间间隔1个骨架硅时,酸强度比孤立的酸性位明显降低;当间隔的硅原子数增加时,酸强度呈上升趋势,间隔3个以上骨架硅时,其酸强度与孤立的酸性位几乎没有差别.对于乙烯的吸附,当两个骨架铝之间间隔1~4个骨架硅时,其吸附能几乎没有差别(31~35 kJ/mol);对于苯的吸附,当两个骨架铝之间间隔1个骨架硅时,其吸附能有所提高,因为两个桥羟基同时对苯分子产生氢键吸附作用.当两个骨架铝之间的距离增大时,苯的吸附能几乎相同(21~29 kJ/mol).若两个乙烯分子或苯分子同时吸附在双酸性位上,其吸附能与单个分子在孤立酸性位吸附时几乎没有差别.应用自然键轨道计算分析了吸附配合物的电子结构,进一步探明了乙烯和苯在分子筛酸性位上吸附的本质.     

Specific ethene surface activation on silver oxide covered Ag[111] from the interplay of STM experiment and theory

High-resolution scanning tunneling microscopy (STM) images at 5 K, simultaneously resolving the molecular adsorbate and the honeycomb structure of the well-defined Ag[111]-p(4 x 4)+Ag(1.83)O substrate, assign the adsorption site for ethene on the silver oxide surface. Ethene molecules are exclusively adsorbed above a particular subset of Ag(delta)(+) sites in the hexagonal rings of the oxide. Extensive density functional theory (DFT) slab calculations confirm that this is the most stable site, with an adsorption energy of 0.4 eV (39 kJ mol(-1)). Adsorption is accompanied by a large deformation of the hexagonal oxide ring and a significant increase in the C-C bond length. STM image simulations provide qualitative agreement with the experimental images, and the molecular orientation is discussed with the help of simple molecular orbital arguments.     

三水合高氯酸镨与18-冠-6配合的研究

采用半微量相平衡方法研究了三元体系Pr(ClO4)3.3H2O-18C6-C2H5OH在298.15K的溶解度, 测定了饱和溶液的折光率。该体系在298.15K时生成两种化学计量的配合物: Pr(ClO4)3.18C6.3H2O(1)和Pr(ClO4)3.2(18C6).3H2O(2)。制备了两种固态配合物, 用化学分析, IR, DTG和TG研究了配合物的组成和性质, 采用量热法, 测定了298.15K时18C6, 配合物1和2在乙醇中的积分溶解热, 以及Pr(ClO4)3.3H2O在18C6-C2H5OH溶液中的积分溶解热。利用本文设计的热化学循环, 求得了两种配合物的标准生成焓。     

A density functional theory study of hydrogen adsorption in MOF-5

Ab initio molecular dynamics in the generalized gradient approximation to density functional theory and ground-state relaxations are used to study the interaction between molecular hydrogen and the metal-organic framework with formula unit Zn4O(O2C-C6H4-CO2)3. Five symmetrically unique adsorption sites are identified, and calculations indicate that the sites with the strongest interaction with hydrogen are located near the Zn4O clusters. Twenty total adsorption sites are found around each Zn4O cluster, but after 16 of these are populated, the interaction energy at the remaining four sites falls off significantly. The adsorption of hydrogen on the pore walls creates an attractive potential well for hydrogen in the center of the pore. The effect of the framework on the physical structure and electronic structure of the organic linker is calculated, suggesting ways by which the interaction between the framework and hydrogen could be modified.     

Surface modification of TiO2 nanoparticles with AHAPS aminosilane: distinction between physisorption and chemisorption

This paper addresses the surface modification of TiO₂ nanoparticles with n-(6-aminohexyl)aminopropyltrimethoxysilane (AHAPS) using various initial aminosilane concentrations. The main objective of this article is to show experimentally the importance of the physisorption during the grafting process. The distinction between chemisorbed and physisorbed aminosilane molecules on TiO₂ is thoroughly analyzed. The surface of bare and modified TiO₂ particles has been characterized by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) to gain a better understanding of the adsorption mechanism of AHAPS on TiO₂. Quantitative information on surface energy of TiO₂, in terms of adsorption energy sites and heterogeneity, has been investigated by quasi-equilibrium low-pressure adsorption technique using nitrogen and argon as probe molecules. The FTIR and XPS data are combined to estimate and discuss the chemisorbed and physisorbed contribution. The results demonstrate that both physisorption and chemisorption occurs but they display a different behavior. The physisorbed amounts are much higher than the chemisorbed amounts. This shows that the main part of the adsorbed layer is composed of physisorbed molecules. The physisorbed uptake depends highly on the AHAPS concentration while the chemisorbed amount remains constant. Quasi-equilibrium Ar derivative adsorption isotherms reveal that the AHAPS molecules are mostly located on the {101} and {001} faces of titania and that the two faces display the same reactivity toward AHAPS sorption. Nitrogen adsorption experiments show that the sorption takes place on the three polar surface sites of high energy. The molecules are chemisorbed onto the site displaying the highest energy while they are physisorbed on the two lower energy sites.     

Comparative study of the interaction of O2 and C2H4 with small vanadium clusters from density functional theory

We have studied C(2)H(4) and O(2) molecules separately or simultaneously for adsorption on V(n) (n = 2-8) clusters, and V(n) clusters catalyzed ethylene oxidation to acetaldehyde using spin-polarized density functional theory calculations. Molecular adsorption and clear size-dependent adsorption energy are predicted for C(2)H(4). O(2) is dissociately adsorbed with nearly constant adsorption energy. In the case of coadsorption, O(2) and C(2)H(4) adsorb on the V(n) surface simultaneously. Each keeps the same adsorption form, molecular or dissociative, as in separate adsorption. The noted cooperative effect is noted in C(2)H(4) and O(2) coadsorption, which activates the C-C double bond of C(2)H(4) and favors its oxidization. Furthermore, both the separate and coadsorptions result in magnetic enhancement or reduction of V(n), which is found to be dependent on the cluster size and the adsorbates. In addition, we reveal the reaction mechanism of V(2) (V(6))-catalyzed ethylene oxidation to acetaldehyde and find the overall reaction is exothermic and barrierless.     

氧原子和羟基在Ni低指数表面的吸附动力学研究

应用5-参数Morse势方法模拟了O－Ni表面相互作用势,考察了氧原子在镍三个低指数表面的吸附特性.同时构造了羟基与Ni（100）、Ni（110）和Ni（111）表面相互作用的推广LEPS势,获得了羟基在表面的吸附位、吸附几何、结合能及本征振动等数据.理论结果表明,羟基垂直吸附于镍表面的高对称位是稳定的,垂直吸附于Ni（100）表面4-重洞位的吸附能为96.98 kJ•mol－1,垂直吸附于Ni（111）表面3-重洞位的吸附能为96.00 kJ•mol－1,在Ni（110）表面存在两种吸附态：垂直吸附于长桥位的吸附能为99.38 kJ•mol－1,倾斜14°吸附于赝势三重位吸附能为96.98 kJ•mol－1.理论结果与实验结果符合得较好.     

Organometallic derivatives of fullerenes: a DFT study of (eta2-Cx)[Pt(PH3)2]n (x = 60, 70, 84; n = 1-6)

To determine the relationship among curvature, patch type, and reactivity of the C-C site, a series of density functional calculations were performed on several substituted fullerenes. [6:6] pyracylene-type sites are the most reactive sites in all analyzed cages: C(60), C(70), and C(84). The binding energy between the Pt(PH(3))(2) unit and fullerene is almost independent of the size of the cage and of the number of metals coordinated on the fullerene surface. Contrarily, curvature and type of carbon-carbon bond are determinant for the coordination strength. The use of relatively large basis sets is necessary to have consistent energies.     

Comparison between electron transfer and nucleophilic reactivities of ketene silyl acetals with cationic electrophiles

The products and kinetics for the reactions of ketone silyl acetals with a series of p-methoxy-substituted trityl cations have been examined, and they are compared with those of outer-sphere electron transfer reactions from 10,10'-dimethyl-9,9', 10, 10'- tetrahydro-9,9'-biacridine [(AcrH)2] to the same series of trityl cations as well as other electron acceptors. The C-C bond formation in the reaction of beta,beta-dimethyl-substituted ketene silyl acetal (1: (Me2C=C(OMe)OSiMe3) with trityl cation salt (Ph3C+ClO4-) takes place between 1 and the carbon of para-positon of phenyl group of Ph3C+, whereas a much less sterically hindered ketene silyl acetal (3: H2C=C(OEt)OSiEt3) reacts with Ph3C+ at the central carbon of Ph3C+. The kinetic comparison indicates that the nucleophilic reactivities of ketene silyl acetals are well correlated with the electron transfer reactivities provided that the steric demand at the reaction center for the C-C bond formation remains constant.