Polymeric salen-Ti(IV) or V(V) complex catalyzed asymmetric synthesis of O-acetylcyanohydrins from KCN, Ac2O and aldehydes

Polymeric salen-Ti(IV) and V(V) complexes were employed in the enantioselective O-acetyl cyanation of aldehydes with potassium cyanide and acetic anhydride. The crosslinked polymeric salen-Ti(IV) catalyst exhibited good activities and enantioselectivities, up to 91% ee with 99% conversion was obtained at −20 °C with 1 mol% of catalyst (based on bimetallic catalytic unit). Moreover, six consecutive recyclings with the easily recovered crosslinked polymeric catalyst showed no obvious decrease in either activity or enantioselectivity. Linear polymeric salen-V(V) catalyst showed good catalytic efficiency too, up to 94% ee with 99% conversion was obtained at −42 °C with 5 mol% of catalyst.     

Bio-oil production from Onopordum acanthium L. by slow pyrolysis

In this study, the usability of the plant thistle, Onopordum acanthium L., belonging to the family Asteraceae (Compositae), in liquid fuel production has been investigated. The experiments were performed in a fixed-bed Heinze pyrolysis reactor to investigate the effects of heating rate, pyrolysis temperature and sepiolite percentage on the pyrolysis product yields and chemical compositions. Experiments were carried out in a static atmosphere with a heating rate of 7 °C/min and 40 °C/min, pyrolysis temperature of 350, 400, 500, 550 and 700 °C and particle size of 0.6 < D_p < 0.85 mm. Catalyst experiments were conducted in a static atmosphere with a heating rate of 40 °C/min, pyrolysis temperature of 550 °C and particle size of 0.6 < D_p < 0.85 mm. Bio-oil yield increased from 18.5% to 27.3% with the presence of 10% of sepiolite catalyst at pyrolysis temperature of 550 °C, with a heating rate of 40 °C/min, and particle size of 0.6 < D_p < 0.85 mm. It means that the yield of bio-oil was increased at around 48.0% after the catalyst added. Chromatographic and spectroscopic studies on the bio-oil showed that the oil obtained from O. acanthium L. could be used as a renewable fuels and chemical feedstock.     

Efficient, solventless N-Boc protection of amines carried out at room temperature using sulfamic acid as recyclable catalyst

A simple, rapid, and efficient protocol for the chemoselective N-Boc protection of amines using sulfamic acid as catalyst is described. N-Boc protection of various structurally diverse aliphatic, aromatic, alicyclic, and heterocyclic amines (1°, 2°, 3°) was carried out with (Boc)₂O using sulfamic acid as catalyst (5 mol %) at room temperature under solventless conditions. The advantages of this method are simplicity, shorter reaction times (1-15 min), a cost-effective catalyst, and excellent isolated yields (90-100%); it is also environmentally benign. Moreover, the combined use of ultrasound and sulfamic acid achieves a synergic effect that is especially marked in the N-Boc protection of deactivated (sterically hindered and electron-deficient) amines. The catalyst possesses distinct advantages: ease of handling, cleaner reactions, high activity, and excellent chemoselectivity.     

New N,N-amino-diphosphonate-containing methacrylic derivatives, their syntheses and radical copolymerizations with MMA

Hydroxy-amino-diphosphonates HO-C_n-NH₂, with 2 ? n ? 11, have been successfully synthesized via the Kabachnick-Field reaction at 70 °C with high yields. These hydroxy compounds are then reacted with methacryloyl chloride to lead to novel amino-diphosphonate methacrylates MAC_nNP₂ (with 2 ? n ? 11). These highly pure methacrylate monomers were obtained with yields higher than 75%. Radical copolymerizations of MAC_nNP₂ (with 2 ? n ? 11) with MMA have been conducted and the r₁ values (related to MAC_nNP₂) are in the range of 1.1-1.3, and r₂ values (related to MMA) about 0.8; this shows that the diphosphonate groups are statistically bonded to the methacrylic backbone.     

Facile nucleophilic fluorination by synergistic effect between polymer-supported ionic liquid catalyst and tert-alcohol reaction media system

A highly efficient method was developed for nucleophilic fluorination using an alkali metal fluoride through the synergistic effect of the polymer-supported ionic liquid (PSIL) as a catalyst and tert-alcohol as an alternative reaction media. This PSIL/tert-alcohol system not only enhances the reactivity of alkali metal fluorides and reduces the formation of by-products but also allows the use of a polymer-supported catalyst protocol. As an example, the nucleophilic fluorinations of the model compound, 2-(3-bromopropoxy)naphthalene, with CsF using only tert-amyl alcohol as solvent (for 2 h reaction time), 0.5 equiv of PS[hmim][BF₄] in CH₃CN (for 12 h reaction time), and 0.5 equiv of PS[hmim][BF₄] in tert-amyl alcohol (which is a PSIL/tert-alcohol system for the synergistic effect; for 2 h reaction time) provided 18, 40, and 84% yield, respectively. The characteristics of the nucleophilic fluorination reactions of some halo- and alkanesulfonyloxyalkane systems to the corresponding fluoroalkanes using various alkali metal fluorides are also reported.     

Efficient synthesis of trisubstituted alkenes in an aqueous-organic system using a versatile and recyclable Rh/m-TPPTC catalyst

We have found that the use of [Rh(cod)OH]₂ associated with the water-soluble ligand m-TPPTC was highly efficient for the Rh-catalyzed arylation of alkynes. Aryl and alkyl alkynes were transformed to alkenes using 3 mol % rhodium catalyst and 2.5 equiv of boronic acid at 100 °C in a biphasic water/toluene system in 80-99% yield. The reaction was found to be totally regioselective for alkyl arylalkynes and alkyl silylated alkynes. The Rh/m-TPPTC system was for the first time recycled with no loss of the activity and with excellent purity of the desired alkene.     

A study on methanol steam reforming to CO2 and H2 over the La2CuO4 nanofiber catalyst

The La₂CuO₄ crystal nanofibers were prepared by using single-walled carbon nanotubes as templates under mild hydrothermal conditions. The steam reforming of methanol (SRM) to CO₂ and H₂ over such nanofiber catalysts was studied. At the low temperature of 150 °C and steam/methanol=1.3, methanol was completely (100%, 13.8 g/h g catalyst) converted to hydrogen and CO₂ without the generation of CO. Within the 60 h catalyst lifespan test, methanol conversion was maintained at 98.6% (13.6 g/h g catalyst) and with 100% CO₂ selectivity. In the meantime, for distinguishing the advantage of nanoscale catalyst, the La₂CuO₄ bulk powder was prepared and tested for the SRM reaction for comparison. Compared with the La₂CuO₄ nanofiber, the bulk powder La₂CuO₄ showed worse catalytic activity for the SRM reaction. The 100% conversion of methanol was achieved at the temperature of 400 °C, with the products being H₂ and CO₂ together with CO. The catalytic activity in terms of methanol conversion dropped to 88.7% (12.2 g/h g catalyst) in 60 h. The reduction temperature for nanofiber La₂CuO₄ was much lower than that for the La₂CuO₄ bulk powder. The nanofibers were of higher specific surface area (105.0 m²/g), metal copper area and copper dispersion. The in situ FTIR and EPR experiments were employed to study the catalysts and catalytic process. In the nanofiber catalyst, there were oxygen vacancies. H₂-reduction resulted in the generation of trapped electrons [e] on the vacancy sites. Over the nanofiber catalyst, the intermediate H₂CO/HCO was stable and was reformed to CO₂ and H₂ by steam rather than being decomposed directly to CO and H₂. Over the bulk counterpart, apart from the direct decomposition of H₂CO/HCO to CO and H₂, the intermediate H₂COO might go through two decomposition ways: H₂COO=CO+H₂O and H₂COO=CO₂+H₂.     

Cu(OTf)2-catalyzed synthesis of imidazo[1,2-a]pyridines from α-diazoketones and 2-aminopyridines

α-Diazoketones undergo smooth coupling with 2-aminopyridines in the presence of 10 mol % of copper(II) triflate to produce the corresponding 2-substituted imidazo[1,2-a]pyridines (IPs) in excellent yields with high selectivity. Rh₂(OAc)₄ is also found to be an equally effective catalyst for this transformation.     

Lewis acid catalyzed asymmetric halohydrin reactions of chiral α,β-unsaturated carboxylic acid derivatives with N-halosuccinimide (NXS) as the halogen source

Lewis acid catalyzed asymmetric halohydrin reactions—(halohydroxylation as well as halomethoxylation) of chiral α,β-unsaturated carboxylic acid derivatives were performed using N-halosuccinimide (NXS; X = Br, I) as the halogen source. Regio- and anti-selectivity of 100% and moderate to good diastereoselectivity with good yields were observed when Oppolzer’s sultam was used as the chiral auxiliary. Among the Lewis acids, Yb(OTf)₃ was found to be the best catalyst. Alkenoyl and cinnamoyl substrates smoothly underwent bromohydrin reactions and the more electron-rich cinnamoyl substrates preferred to undergo iodohydrin reactions. However, electron-deficient cinnamoyl substrates did not respond to this Lewis acid catalyzed halohydrin reaction with NXS (X = Cl, Br, I).     

Synthesis and decarboxylation of N-acyl-α-triphenylphosphonio-α-amino acids: a new synthesis of α-(N-acylamino)alkyltriphenylphosphonium salts

4-Phosphoranylidene-5(4H)-oxazolones 1 undergo hydrolysis in THF in the presence of HBF₄ at room temperature to give N-acyl-α-triphenylphosphonioglycines 3 (R² = H) in very good yields. 4-Alkyl-4-triphenylphosphonio-5(4H)-oxazolones 2 react with water in CH₂Cl₂/THF solution without any acidic catalyst at 0-5 °C in a few days yielding N-acyl-α-triphenylphosphonio-α-amino acids 3 (R² = Me) or α-(N-acylamino)alkyltriphenylphosphonium salt 4 (R² = CH₂OMe). α-Triphenylphosphonio-α-amino acids 3, on heating up to 105-115 °C under reduced pressure (5 mmHg) or on treatment with diisopropylethylamine in CH₂Cl₂ at 20 °C undergo decarboxylation to give the corresponding α-(N-acylamino)alkyltriphenylphosphonium salts 4, usually in very good yields.     

Thermo-Raman spectroscopy in situ monitoring study of solid-state synthesis of NiO-Al2O3 nanoparticles and its characterization

Hyphenation of thermogravimetric analyzer (TGA) and thermo-Raman spectrophotometer for in situ monitoring of solid-state reaction in oxygen atmosphere forming NiO-Al₂O₃ catalyst nanoparticles is investigated. In situ thermo-Raman spectra in the range from 200 to 1400 cm⁻¹ were recorded at every degree interval from 25 to 800 °C. Thermo-Raman spectroscopic studies reveal that, although the onset of formation is around 600 °C, the bulk NiAl₂O₄ forms at temperatures above 800 °C. The X-ray diffraction (XRD) spectra and the scanning electron microscopy (SEM) images of the reaction mixtures were recorded at regular temperature intervals of 100 °C, in the temperature range from 400 to 1000 °C, which could provide information on structural and morphological evolution of NiO-Al₂O₃. Slow controlled heating of the sample enabled better control over morphology and particle size distribution (∼20-30 nm diameter). The observed results were supported by complementary characterizations using TGA, XRD, SEM, transmission electron microscopy, and energy dispersive X-ray analysis.     

Poly(4-vinylpyridine-co-divinylbenzene) supported iron(III) catalyst for selective oxidation of toluene to benzoic acid with H2O2

Poly(4-vinylpyridine-co-divinylbenzene) supported iron(III) catalysts were developed for the selective oxidation of toluene to benzoic acid in the presence of H₂O₂. The influence of the DVB content on the capacity of immobilized Fe(III) and on the catalytic activities of the polymeric complexes was investigated. The extent of Fe(III) uptake by the copolymers varied slightly with the concentration of DVB. The catalytic activities generally increase with increasing degree of crosslinker from 2 to 10% and decrease further with increasing the DVB content. Under the optimal conditions (80 °C, 6 h), the catalyst containing 10% DVB was found to be highly efficient in conversion of toluene to benzoic acid with 90% conversion and 96% selectivity.     

The direct decomposition of NO over the La2CuO4 nanofiber catalyst

The NO catalytic direct decomposition was studied over La₂CuO₄ nanofibers, which were synthesized by using single walled carbon nanotubes (CNTs) as templates under hydrothermal condition. The composition and BET specific surface area of the La₂CuO₄ nanofiber were La₂Cu_0.88²⁺Cu_0.12⁺O_3.94 and 105.0 m²/g, respectively. 100% NO conversion (turnover frequency-(TOF): 0.17 g_NO/g_catalyst s) was obtained over such nanofiber catalyst at temperatures above 300 °C with the products being only N₂ and O₂. In 60 h on stream testing, either at 300 °C or at 800 °C, the nanofiber catalyst still showed high NO conversion efficiency (at 300 °C, 98%, TOF: 0.17 g_NO/g_catalyst s; at 800 °C, 96%, TOF: 0.16 g_NO/g_catalyst s). The O₂ and NO temperature programmed desorption (TPD) results indicated that the desorption of oxygen over the nanofibers occurred at 80-190 and 720-900 °C; while NO desorption happened at temperatures of 210-330 °C. NO and O₂ did not competitively adsorb on the nanofiber catalyst. For outstanding the advantage of the nanostate catalyst, the usual La₂CuO₄ bulk powder was also prepared and studied for comparison.     

Combined microwave-assisted isolation and solid-phase purification procedures prior to the chromatographic determination of phenolic compounds in plant materials

A fast, sensitive and selective procedure employing a combination of microwave-assisted extraction (MAE) and solid phase extraction (SPE) was applied prior to liquid chromatographic identification and quantification of phenolic compounds in plant materials. MAE has been tested and optimized for the isolation of phenolic acids (gallic, protocatechuic, p-hydroxybenzoic, chlorogenic, vanilic, caffeic, syringic, p-coumaric, ferulic, sinapic, benzoic, m-coumaric, o-coumaric, rosmarinic, cinnamic acids) and 3,4-dihydroxybenzaldehyde, syringaldehyde, p-hydroxybenzaldehyde, and vanillin in various plants. The effects of experimental conditions on MAE efficiency, such as solvent composition, temperature, extraction time, have been studied. The extraction efficiencies were compared with those obtained by computer-controlled, two-step Soxhlet-like extractions. Plant extracts were purified and phenolic compounds were pre-concentrated using SPE on polymeric RP-105 SPE sorbent prior to HPLC analysis. Chromatographic separation was carried out on a Hypersil BDS C₁₈ column using a mobile phase consisted of 0.3% (v/v) acetic acid in water (solvent A) and methanol (solvent B) at flow rate 0.6 ml min⁻¹ and column temperature 30 °C with gradient elution.     

Identification and determination of carboxylic acids in food samples using 2-(2-(anthracen-10-yl)-1H-phenanthro[9,10-d]imidazol-1-yl)ethyl 4-methylbenzenesulfonate (APIETS) as labeling reagent by HPLC with FLD and APCI/MS

A new labeling reagent for carboxylic acids, 2-(2-(anthracen-10-yl)-1H-phenanthro[9,10-d]imidazol-1-yl)ethyl 4-methylbenzenesulfonate (APIETS) has been designed and synthesized. It was used to label eight fatty acids (lauric acid, myristic acid, palmitic acid, stearic acid, arachidic acid, oleic acid, linoleic acid and linolenic acid) and four hydroxy pentacyclic triterpene acids (oleanolic acid, ursolic acid, betulinic acid and maslinic acid), successfully. APIETS could easily and quickly label carboxylic acids in the presence of K₂CO₃ catalyst at 85 °C for 35 min in N,N-dimethylformamide solvent. The carboxylic acids derivatives were separated on a C₈ reversed-phase column with gradient elution and fluorescence detection at λ_ex/λ_em = 315/435 nm. Identification of these derivatives was carried out by online mass spectrometry with atmospheric pressure chemical ionization in positive ion mode. The detection limits obtained were 13.37-30.26 fmol (signal-to-noise ratio of 3). The proposed method has been applied to the quantification of carboxylic acids in sultana raisin (Thompson seedless), hawthorn flake (Crataegus pinnatifida Bge.), Lycium barbarum seed oil and Microula sikkimensis seed oil with recoveries over 95.3%. It has been demonstrated that APIETS is a prominent labeling reagent for determining carboxylic acids with high performance liquid chromatography.     

Synthesis of a novel bistriazene reagent 4,4′-bis[3-(4-phenylthiazol-2-yl)triazenyl]biphenyl and its highly sensitive color reaction with mercury(II)

We report the synthesis of a novel bistriazene, 4,4′-bis(3-(4-phenylthiazol-2-yl)triazenyl)biphenyl (BPTTBP), and its highly sensitive color reaction with Hg²⁺. The new reagent was synthesized in good yield by coupling 2-amino-4-phenylthiazole with 4,4′-biphenyldiamine bisdiazonium salt. Using a blend of surfactants N-cetylpyridinium chloride (CPC) and polyethylene glycol n-octanoic phenyl ether (OP) as a micelle sensitizer, the red colored reagent assembles with Hg²⁺ in pH 9.8 borate buffer according to a 1:1 stoichiometry, forming a blue oligomeric/polymeric chelating complex with a high apparent stability constant (1.1 × 10⁸ M⁻¹). Whereas the maximum absorption of reagent occurs at 510 nm with an extinct coefficient of 1.35 × 10⁴ M⁻¹ cm⁻¹, the complex absorbs at 611 nm, with an apparent extinct coefficient of 1.04 × 10⁵ M⁻¹ cm⁻¹. Beer's law is obeyed in the range of 0-15 μg/25 mL Hg²⁺, and Sandell's sensitivity is 1.92 × 10⁻³ μg/cm². In the presence of thiourea and Na₄P₂O₇ as masking agents, the method was found free from interferences of foreign ions commonly occurring with mercury. The optimized protocol has been successfully applied to spectrophotometric determination of mercury in waste water samples. The features of the new reagent associated with its special structure were discussed, and an unprecedented “domino effect” was proposed to account for its unique chelating stoichiometry with Hg²⁺.     

Silica gel supported TaBr5: new catalyst for the facile and rapid cyclization of 2′-aminochalcones to the corresponding 2-aryl-2,3-dihydroquinolin-4(1H)-ones under solvent-free conditions

Silica gel supported TaBr₅ (5-10 mol %) is a new solid-support catalyst that can be used under solvent-free conditions for the facile and efficient isomerization of 2′-aminochalcones to the corresponding 2-aryl-2,3-dihydroquinolin-4(1H)-ones. The catalyst is easily prepared, stable and employed under environmentally friendly conditions.     

Effects of cocatalyst on structure distribution of propylene polymers catalyzed by rac-Me2Si(Ind)2ZrCl2/aluminoxane

Propylene polymerization and propylene/1-octene copolymerization were studied using rac-Me₂SiInd₂ZrCl₂(1)/MAO or rac-Me₂SiInd₂ZrCl₂/(MAO + TIBA) as catalyst (methyl aluminoxane, MAO; AliBu₃, TIBA). The structure distribution of the polymers was characterized by temperature gradient extraction fractionation or precipitation fractionation, as well as by DSC analysis of the thermal segregated samples. By comparing the structure distribution of polypropylene and propylene-1-octene copolymer synthesized by 1/MAO and 1/(MAO + TIBA), it is found that adding TIBA in the catalyst system increase the blockiness of the polymer chain, especially in the copolymerization system. It is assumed that, when iso-butyl is incorporated in the aluminoxane, ion pair of the active center and the aluminoxane counter ion may exist in different states that show different catalytic behaviors, resulting in the formation of polymers with block structure.     

Synthesis and structural characterization of silver(I) complexes with moon-shaped benzo[1,2-b;4,3-b′]dithiophene phosphine derivative ligands

New silver complexes of general formula [Ag(O₃SCF₃)(PPh₂{bzt})_n] (n = 1–3, bzt = benzo[1,2-b;4,3-b′]dithiophene) have been synthesized and characterized. Spectroscopic studies shown neutral ligand fluxionallity, typical of silver(I) complexes. The solid state structure of the complexes was determined by X-ray crystallographic studies, showing a decrease in structure complexity with increasing number of neutral ligands in silver coordination sphere: [Ag(O₃SCF₃)(PPh₂{bzt})] is a dimer with two bridging triflate anions, further linked into polymeric bidimensional chains along bc plane, through Ag?Ph close contacts; Ag(O₃SCF₃)(PPh₂{bzt})₂] is also a dimmer with two bridging triflate anions, displaying an interesting packing feature, with zig-zag alignment of bzt groups along direction b; [Ag(O₃SCF₃)(PPh₂{bzt})₃] is a monomer.     

Application of ring study: water toxicity determinations by bioluminescence assay with Vibrio fischeri

Acceptance of toxicity bioassays as effective analytical tools in environmental areas needs guarantees of standardization but also validation. Ten European laboratories took part in an inter-laboratory study using different commercial devices based on bioluminescence inhibition of bacteria Vibrio fischeri. Reproducibility and stability by short toxicity endpoints, effective concentration that gives 10%, 50% and 80% of inhibition (EC₁₀, EC₅₀ and EC₈₀) is evaluated. Parametric and non-parametric statistic is applied and performance of participant laboratories is addressed by z-scores calculated by non-parametric statistic. z-Score classification was based on harmonised protocol for proficiency testing of analytical laboratories (satisfactory |z| ≤ 2; questionable 2 < |z| ≤ 3; unsatisfactory |z| > 3). Tested samples were phenol, 3,5-dichlorophenol and influent wastewater. Based on z-score classification, more than 70% of the laboratories showed a satisfactory performance for phenol, 3,5-dichlorophenol and influent wastewater (86%, 90% and 70%, respectively). Reproducibility and stability was observed in toxicant references and in wastewater samples. EC₈₀ determination appears to be more robust that EC₁₀ and EC₅₀. EC determinations can be considered favorable at 5 and 15 min of exposition, in particular for EC₈₀. The use of different commercial devices can not be considered an additional source of variation.