Fabrication of carboxymethyl functionalized β-cyclodextrin-modified graphene oxide for efficient removal of methylene blue

In this study, a novel carboxymethyl functionalized β-cyclodextrin-modified graphene oxide (CM-β-CD-GO) adsorbent was designed and fabricated. The CM-β-CD-GO was applied to remove methylene blue (MB) from aqueous solutions. The adsorption mechanism was discussed in detail through the study of pH effect, kinetics, and isotherm models. The adsorption of CM-β-CD-GO for MB displayed high removal rates at the pH range of 6.0–10.0, and the removal efficiency is over 90% within 20 min. The pseudo-second-order model could well describe the kinetic process of MB adsorption, and the adsorption was determined by the multi-step process. The maximum uptake capability of CM-β-CD-GO towards MB was 245.70 mg g⁻¹ at 25 °C according to Langmuir isotherm model. A possible adsorption mechanism that electrostatic attraction, π-π interaction, and host-guest supramolecular interactions supported MB adsorption was proposed. The adsorption capacity of CM-β-CD-GO showed no significant change after five cycles. The structure and morphology of CM-β-CD-GO were characterized by XPS, FT-IR, TGA, PXRD, AFM, SEM, zeta (ζ) potential determination, and Raman spectroscopy. This work provides valuable information for the design of novel adsorbents that specifically and efficiently adsorb cationic dyes contaminants.     

Non-functionalized oil palm waste-derived reduced graphene oxide for methylene blue removal: Isotherm,kinetics, thermodynamics,and mass transfer mechanism

The discharge of colored effluents from industries is one of the significant sources of water pollution. Therefore, there is a growing demand for efficient and low-cost treatment methods. An adsorption process with reduced graphene oxide (rGO) synthesized using a novel double carbonization and oxidation method from the natural precursor of oil palm empty fruit bunch (OPEFB) as adsorbent is a promising approach for addressing the problem. In this study, OPEFB biochar was mixed with ferrocene with a ratio of 5:1 (m/m) and oxidized under nitrogen flow at a temperature of 300 °C for 20 min, which resulted in 75.8 wt% of yield. The potential of the synthesized rGO as an effective adsorbent for dye removal from water and wastewater was explored using methylene blue (MB) as a model. Several factors were investigated, including adsorbent dosage, initial concentration, contact time, and pH, to obtain the optimum adsorption condition through batch studies. The physical and chemical characteristics of the rGO in terms of functional groups, surface morphology, elemental composition, and crystallinity phase were determined through characterization. The nonlinear isotherms were appropriated using several error functions to describe the adsorption isotherm with a maximum adsorption capacity of 50.07 mg/g. The kinetic study demonstrates that MB’s adsorption fits the PFO kinetic model and agrees with Bangham’s interpretation of pore diffusion. The adsorption mechanism was found to be physisorption on the multilayer heterogeneous surface of the rGO involving π-π interaction, hydrophobic association, and electrostatic interaction. The thermodynamics study showed that the process was spontaneous and exothermic. The mass transfer mechanism study shows that the adsorption is controlled by intraparticle diffusion and involves complex pathways. The study found that the novel non- functionalized rGO could remove cationic dyes from water and wastewater.     

Porous graphene oxide-based carbon artefact with high capacity for methylene blue adsorption

A three-dimensional porous graphene oxide (PGO) material prepared by hydrothermal method was selected to adsorb methylene blue (MB), which demonstrates a high MB adsorption capacity, up to 1100 mg g^?1 in alkaline solution at room temperature. The influences of different pore structures and different contents of oxygen-containing functional groups on MB adsorption behaviors were studied in detail, which indicated that the high MB adsorption capacity is mainly ascribed to the synergistic effect of the large number of oxygen-containing functional groups and the interconnected 3D porous network. Moreover, based on the investigation on the adsorption kinetics and the effect of pH value on MB adsorption, we propose a two-step adsorption kinetics for PGO, which involved in two interactions between MB molecular and porous graphene oxide-based carbon: electrostatic force and π-π stacking. Besides, the calculation of the activation energies indicates that chemisorption dominates the adsorption for PGO in comparison with physisorption for three-dimensional porous graphene materials which has low adsorption capacity because of the removal of functional groups. The results are of great significance for the design and environmental applications of PGO as a promising adsorbent material for water purification.     

Characterization and Mechanism Elucidation of Dye Adsorption Using Cuprous Selenide Nanoparticles from Aqueous Solutions

The removal of cationic dyes, methylene blue(MB) and rhodamine B(RB), and anionic dyes, methyl or-ange(MO) and eosin Y(EY), from aqueous solutions by adsorption using Cu₂Se nanoparticles(Cu₂SeNPs) was studied. The effects of the initial pH values, adsorbent doses, contact time, initial dye concentrations, salt concentrations, and operation temperatures on the adsorption capacities were investigated. The adsorption process was better fitted the Langmuir equation and pseudo-second-order kinetic model, and was spontaneous and endothermic as well. The adsorption mechanism was probably based on the electrostatic interactions and π-π interactions between Cu₂SeNPs and dyes. For an adsorbent of 0.4 g/L of Cu₂SeNPs, the adsorption capacities of 23.1(MB), 22.9(RB) and 23.9(EY) mg/g were achieved, respectively, with an initial dye concentration of 10 mg/g(pH=8 for MB and pH=4 for RB and EY) and a contact time of 120 min. The removal rate of MB was still 70.4% for Cu₂SeNPs being reused in the 5th cycle. Furthermore, the recycled Cu₂SeNPs produced from selenium nanoparticles adsorbing copper were also an effective adsorbent for the removal of dyes. Cu₂SeNPs showed great potential as a new adsorbent for dyes removal due to its good stability, functionalization and reusability.     

Green synthesis of loofah-based biosorbent via radiation grafting for effective removal of methylene blue

A new loofah-based biosorbent with high adsorption capacity for cationic dye was synthesized by a one-step co-radiation grafting method. The successful grafting of sodium 4-vinylbenzene sulfonate (SSS) onto loofah sponge (LFs) through electron beam radiation can significantly improve the remove capacity of methylene blue in wastewater. The biosorbent with a 409.67 mg/g of uptake capacity for methylene blue (MB), was higher than most of the loofah based adsorbents reported. FT-IR, elemental analysis, XRD, SEM and TG were used to analyze the changes in the functional group composition, element content, morphology, thermal stability of the obtained biosorbent. The pH, contact time, temperature and the effect of dosage on adsorption were also investigated. The results showed that the adsorption behavior well accorded with the pseudo-second-order kinetic and Langmuir adsorption model, which proved that the adsorption was a single-layered and chemisorption process. The thermodynamic parameters suggested a spontaneous and endothermic process. XPS analysis confirmed a potential adsorption mechanism was based on hydrogen bond interaction, electrostatic interaction and π-π stacking. Additionally, the adsorbent owned outstanding reusability, which could be reused five times with a slight reduction of removal rate. Overall, this research enriches the MB trapping agent and provides a new methods for the reuse of waste natural loofah sponge, and it will be a valuable research with the advantages of low cost and less environmental pollution.     

Removal of methylene blue by two zeolites prepared from naturally occurring Egyptian kaolin as cost effective technique

The optimum condition as well as adsorption behavior of two zeolite types prepared from Egyptian kaolin (namely, zeolite A and zeolite X) with methylene blue (MB) are demonstrated in this study. This will be a step to remove such dyes from textile as well as dying industries.MB removal was investigated using synthetic solutions at initial concentrations 15 mg/L of MB at constant temperature and pH (25 ± 0.1 °C and 7.5 ± 0.2) respectively. The removal efficiency was determined at different contact times and different zeolite doses.The optimum contact times for the removal of MB were 60 min and 75 min for zeolite X and zeolite A, respectively. 0.6 g was the optimum dose for removal of MB with both zeolite types.The batch method has been employed, using MB concentration in solution ranging from 2 to 25 mg/L. The percentage removal and distribution coefficients (K_d) were determined for the adsorption system as a function of sorbate concentration. The isothermal models investigated in this study show that adsorption ratios of MB on both zeolites match to Langmuir and Freundlich equation adding to that every equation constant has been calculated. According to the equilibrium studies, adsorption of zeolite X in higher concentrations is much better than that of zeolite A. Dublin–Kaganer–Radushkevich (DKR) shows physisorption endothermic adsorption process for both zeolites and also linear correlation of Redlich–Peterson and Tekman isothermal models were proved.These results show that zeolites prepared from naturally abundant Egyptian kaolin hold great potential to remove dying materials such as MB from wastewater. This will encourage using such low cost technique in removal of dyes from industrial wastewater.     

Porous multicomponent chitosan/poly(ε-caprolactone)-block poly (ethylene glycol)/SiO2 aerogel@polydopamine membrane for Congo red adsorption

A composite adsorbent, chitosan//poly (ε-caprolactone)-block poly (ethylene glycol)/SiO₂ aerogel@polydopamine (CS/PCL-b-PEG/SA@PDA) membrane was prepared for the adsorption of organic dyes. The matrix polymer materials of this novel adsorbent were eco-friendly. SiO₂ aerogel with nanoporous network construction was fixed in the multicomponent polymer fibers through simultaneous electrospinning-electrospray technology followed by modification of polydopamine (PDA). The composite adsorbent had a maximum adsorption capacity of 598.8 mg/g for Congo red (CR) and possessed good reusability performance. This adsorbent showed excellent performance for the selective adsorption of relatively large molecule CR dyes even under high concentration of small molecule methyl orange (MO) dyes or 1 M of salt solution. The adsorption mechanism indicated that the –NH₂ and –OH groups in adsorbent could generate the stronger electrostatic attraction with the –SO₃^- groups in CR. Meanwhile, the sufficient adsorption spaces of the adsorbent were constructed by the porous network structure of SiO₂ aerogel, the accumulation of PDA particles and the porous structure of the multicomponent composite membrane. The work provided a proactive study in designing an adsorbent for the selective adsorption of organic dyes.     

Activated carbon/MOFs composite: AC/NH2-MIL-101(Cr), synthesis and application in high performance adsorption of p-nitrophenol

P-nitrophenol (PNP), a hazardous phenolic material, should be eliminated from water in order to prevent damage to the marine ecosystem, animals as well as humans. Although adsorption seems to become the most widely used strategy, an effective and strong-capacity adsorbent to minimize PNP under the approved concentration is essential to discovering. In this study, a class of porous adsorbents composite was developed for the PNP removal from water. AC-NH₂-MIL-101(Cr) has chosen to boost the removal of PNP from water owing to extremely porous and stable in water. The fabricated composite has 2049 m².g⁻¹ large surface area and 0.93 cm³.g⁻¹ pore volume. The adsorption kinetics and isotherms were investigated. AC-NH₂-MIL-101(Cr) was found to exhibit an adsorption capacity of ~ 18.3 mg g⁻¹. The mechanism for this strong adsorption performance was suggested and related to affinity NO₂ groups of PNP and the unsaturated chromium site of AC-NH₂-MIL-101(Cr), the coulombic interaction via the hydrogen bond between the PNP and AC-NH₂-MIL-101(Cr) and π-π stacking interaction. AC-NH₂-MIL-101(Cr) composite also displayed exceptional stability and reusability after a successive PNP removal processes. This study provides new insight into developing and synthesizing extremely effective nanoporous material for organic contaminants disinfection from waste water based on MOFs.     

Converting red mud wastes into mesoporous ZSM-5 decorated with TiO2 as an eco-friendly and efficient adsorbent-photocatalyst for dyes removal

Red mud wastes have been converted into mesoporous zeolite socony mobile-5 (ZSM-5) followed by deposited titanium dioxide (TiO₂) nanoparticles to generate synergy adsorption-photodegradation for removal of dye removal in waste water. The amount of TiO₂ loading was varied to achieve optimum photocatalytic activity while maintaining the mesoporosity and high surface area of ZSM-5. Sol-gel method facilitated the formation of anatase TiO₂ on the ZSM-5. The fourier transform infrared spectra clarified the formation of Si–O–Ti at 957 cm^?1 by the exchanging the hydrogen ion with titanium ion, which proved by decreasing the absorption band of Si–OH and Si–O interaction at 964 and 944 cm^?1, respectively. Sol-gel method also preserved the mesopore diameter of ZSM-5 at 3.5 nm which allow the diffusion of methylene blue (MB) molecules into the pores. However, the surface area and the pore volume were slightly reduced with increasing the TiO₂ loading. The adsorption performance of samples showed that the increasing in the TiO₂ loading led to the decreasing in the adsorption capacity. All samples showed the suitability towards the pseudo second order kinetic. The Langmuir isotherm was suitable to describe the adsorption mechanism by monolayer adsorption. Mesoporosity of ZSM-5 accelerated the adsorption of dye via the increase of mass transfer in the pore channel which confirmed by the low intercept of intraparticle diffusion model at the first stage. The photocatalytic test showed that 10% TiO₂ loading on the ZSM-5 exhibited the highest methylene blue removal followed by 5% and 20% TiO₂ loading. Optimization on the amount of photocatalyst and the pH of solution indicated the reaction favoured 1 g L^?1 of catalysts and at alkaline pH. 10% TiO₂/ZSM-5 also exhibited high stability and reusability up to four reaction cycles. Photocatalytic performance of 10% TiO₂/ZSM-5 was further investigated on photodegradation of malachite green and rhodamine B organic dyes, which showed the photocatalytic efficiency of 73 and 88%, respectively. Superoxide radical, hydroxyl radical, and photogenerated electron were identified as the main active species for MB photodegradation based on the reduction of degradation rate following the addition scavenger molecules.     

金属有机框架MIL-101(Fe)对水中微囊藻毒素-LR的吸附

通过溶剂热法制备了性质稳定的金属有机框架材料MIL-101(Fe),并用于吸附去除水中的微囊藻毒素-LR。采用电子显微镜、傅立叶变换红外光谱(FT-IR)、Zeta电位和N_2吸附-脱附等方法对制备的纳米材料进行了表征。MIL-101(Fe)具有多孔结构和较高的比表面积(375.2 m~2/g),尺寸约为500 nm。考察了pH值、离子强度、温度、吸附时间、浓度等参数对吸附剂吸附能力的影响。结果表明,静电作用和配位作用是主要的作用机理。MIL-101(Fe)对微囊藻毒素-LR的吸附速度很快(20 min内达到吸附平衡),吸附过程符合准二级动力学模型;MIL-101(Fe)对微囊藻毒素-LR表现出良好的吸附性能,其最大吸附量为256.4 mg/g。溶液中存在的腐植酸对MIL-101(Fe)的吸附性能产生一定的影响。受腐殖酸、盐类的影响,相同条件下MIL-101(Fe)对江水中微囊藻毒素-LR的吸附性能有所下降,但仍可达到68.1 mg/g。因此,该方法简便、高效,适用于快速除去污染水体中的微囊藻毒素-LR。     

Recent advances on hydrogels based on chitosan and alginate for the adsorption of dyes and metal ions from water

In contemporary times, water resources have become increasingly scarce and suffer from anthropogenic pollution sources with an organic and inorganic origin that are products of industrial, agricultural, and everyday waste. Contamination with heavy metals and dyes in wastewater is considered a risk for water sources that can leak into underground and surface sources, leading to increased biological and chemical contamination. The pollutant removal process is performed by adsorption treatment methods, which is the most common method, and it is considered an effective method with a high and economical removal rate.In this review, we discuss the use of biobased hydrogel adsorbents in the removal of organic dyes and metal ions from water. The literature indicates that hydrogels exhibit rapid absorption kinetics and a dye removal absorption capacity that can reach more than 100 mg/g and sometimes more than 2000 mg/g, with a metal adsorption capacity ranging from 38 mg/g to more than 440 mg/g. These results are discussed and compared by taking into account hydrogel materials that contain biopolymers such as alginate, chitosan or both. In general, absorption depends mainly on biobased materials, which have a natural origin and can be utilized to synthesize hydrogels to remove pollutants, dyes and heavy metals. Chitosan and alginate are prominent materials for this use and they can be incorporated with other components to obtain hydrogels or nanocomposite materials with different efficacies to remove dyes and metal ions.     

The selective and enhanced adsorptive behaviors of supramolecular recrystallized 1,3,5-benzenetricarboxylic acid assembled nano-bacterial cellulose

The effluent discharge produced in the textile printing and dyeing, leather and other fields, will cause the irreversible environmental pollution and extremely threatening safety of living organisms. The appropriate and efficient disposal method of dyestuff originated wastewater has been widely concerned in the past decades. In this study, the recrystallization of 1,3,5-benzene tricarboxylic acid (RCTMA) was put forward via a hydrothermal method to form the supramolecular RCTMA-based hexamer and thereafter assembled into the porous nano-bacterial cellulose (NBC) to construct the RCTMA@NBC composite. The morphology and surface properties of RCTMA@NBC were examined by scanning electron microscope, X-ray diffraction, and Fourier transform infrared spectroscopy. This RCTMA@NBC was employed to adsorb methylene blue (MB) adjusting the pH, temperature, and dosage of adsorbent. The result showed the maximal absorption capacity of RCTMA@NBC appeared under pH = 7.1 and higher temperature will hinder the adsorption of dyes. Moreover, the adsorption isotherms and kinetics were evaluated which was more confirmed to Langmuir model and quasi-second-order kinetic equation, and the simulated maximum adsorption capacities of MB was 1162.12 mg/g. Moreover, cationic golden XGL and anionic brilliant crocein were selected to further verify the distinct adsorptive behavior. The excellent affinity towards cationic dyes proved the easy combination was based on the chemical force originated from mutual attraction between opposite charges, π–π interactions, and H-bonding, whereas the poor attraction for brilliant crocein was due to the electrostatic repulsion between sulfonic and carboxyl groups. The synthesized RCTMA@NBC possesses higher efficiency and selective adsorption, which exhibits the promising potential in the field of precise treatment of organic dye wastewater.     

Ultrasound-aided rapid and enhanced adsorption of anionic dyes from binary dye matrix onto novel hematite/polyaniline nanocomposite: Response surface methodology optimization

In recent times, polyaniline (PANI), a conducting polymer, has been studied widely for environmental remediation application due to its controllable electric conductivity with high surface area, which makes it a suitable adsorbent material. But lower mechanical stability of PANI is considered to be a serious drawback for its large-scale industrial application. To improve the mechanical strength of PANI, in this study, hematite nanoparticles were impregnated onto PANI by oxidative polymerization method in order to fabricate a novel organometallic nanocomposite (hematite-PANI-NC). The hematite-PANI-NC was used as adsorbent for removal of methyl orange (MO) and eosin yellow (EY) dye from binary dye matrix under ultrasonic-assisted adsorption. Excellent MO and EY dye removal (more than 98%) was observed from binary matrix at a wide solution pH from 2.0 to 6.0, and under ultrasound wave the adsorption equilibrium was achieved within 15 min only. Both MO and EY dyes adsorption experimental data strictly followed Langmuir isotherm, and maximum monolayer adsorption capacity of 126.58 mg/g and 112.36 mg/g was observed for MO and EY dye, respectively. The uptake mechanism of MO and EY dyes onto hematite-PANI-NC is governed by electrostatic interaction, π-π bonding and hydrogen bonding between dye molecules and nanocomposite. Response surface methodology analysis reveals maximum MO and EY removal of 98.43% and 99.35% at optimum experimental conditions. This study implies that the hybrid organometallic material hematite-PANI-NC has high potential for quick and enhanced sono-assisted uptake of anionic dyes from water near neutral solution pH.     

磁性金属有机骨架-聚多巴胺的制备并用于水产养殖水样中阳离子染料的萃取检测

利用多巴胺（DA）中的儿茶酚基团能与金属有机骨架晶体（MOFs）中金属离子螯合的原理,以ZIF-67为模板,经DA蚀刻-自聚合形成具有孔洞结构的聚多巴胺（PDA）壳层,制备了磁性-MOFs-PDA（Fe₃O₄@Z67D）新型材料。多种表征手段验证了材料的形貌、结构和性能。新型材料具有亲水性的表面、纳米级的孔径,以及良好的磁响应,被用作磁固相萃取吸附剂。结合高效液相色谱分析手段,建立了萃取检测亚甲蓝（MB）和结晶紫（CV）两种阳离子染料的新方法。在最优的萃取和色谱分析条件下,MB和CV的线性范围分别为0.5~200 μg/L和0.01~50 μg/L,检出限分别为0.04 μg/L和0.008 μg/L,对两种染料的富集因子分别为777和688。新型材料重复使用10次,其萃取性能未见发生变化。该方法成功应用于检测淡水鱼养殖用水中痕量的MB和CV,加标回收率为82.0%~109.0%,RSD低于2.9%。     

功能化金属有机骨架材料去除饮用水污染物的研究进展

金属有机骨架(MOFs)材料是一类以过渡金属为中心、含杂原子的有机物为配体、通过配位作用形成的周期性网络多孔晶体材料。与其他的多孔材料相比,MOFs配体种类繁多,比表面积极大,孔径大小可调控且具有特殊(饱和或不饱和)的金属位点,在气体存储、催化、吸附与分离等领域有广阔的应用前景。近年来,功能化MOFs对污染物的富集和去除成为学者关注的热点。这是由于通过对MOFs进行功能化修饰,能够改变MOFs的孔径大小、表面带电性质等物化性质,从而实现对目标物更高效的吸附。该文综述了近年来功能化MOFs对饮用水污染物吸附的研究进展,包括饮用水污染物的类型及危害、功能化MOFs的制备方法以及去除饮用水污染物的应用,并对今后的发展前景进行了展望。     

Novel dye removing agent based on CTS-g-P(AA-co-NIPAM)/GO composite

A novel composite Chitosan graft poly (acrylic acid-co-N-isopropylacrylamide)/graphite oxide (CTS-g-P(AA-co-NIPAM/GO) is synthesized and used to remove methylene blue (MB) and fuchsin basic (FB) from aqueous solutions by adsorption. Small amount of GO brings about great improvement of the thermostability together with the adsorption amount. Adsorption capacities of MB and FB increase from 842.1 and 633.7 mg/g, respectively, to 1496.3 and 1000.8 mg/g, respectively, with 0.02 g intercalation amount of GO. The interactions between GO and main body of CTS-g-P(AA-co-NIPAM) graft copolymer are hydrogen and amide bonds, whereas that between dye molecules and CTS-g-P(AA-co-NIPAM)/GO composite is hydrogen bond as well as electrostatic interaction. Effect of various conditions on the adsorption capacities is discussed. Adsorption isotherms and thermodynamics are studied. The adsorption of both MB and FB are spontaneous and satisfy the Redlich-Peterson equation. Kinetic study shows that the adsorption of both dyes is in accordance with the Pseudo first-order kinetic model.     

The Use of High Surface Area Mesoporous-Activated Carbon from Longan Seed Biomass for Increasing Capacity and Kinetics of Methylene Blue Adsorption from Aqueous Solution

Microporous- and mesoporous-activated carbons were produced from longan seed biomass through physical activation with CO₂ under the same activation conditions of time and temperature. The specially prepared mesoporous carbon showed the maximum porous properties with the specific surface area of 1773 m²/g and mesopore volume of 0.474 cm³/g which accounts for 44.1% of the total pore volume. These activated carbons were utilized as porous adsorbents for the removal of methylene blue (MB) from an aqueous solution and their effectiveness was evaluated for both the adsorption kinetics and capacity. The adsorption kinetic data of MB were analyzed by the pseudo-first-order model, the pseudo-second-order model, and the pore-diffusion model equations. It was found that the adsorption kinetic behavior for all carbons tested was best described by the pseudo-second-order model. The effective pore diffusivity (D_e) derived from the pore-diffusion model had the values of 4.657 × 10⁻⁷–6.014 × 10⁻⁷ cm²/s and 4.668 × 10⁻⁷–19.920 × 10⁻⁷ cm²/s for the microporous- and mesoporous-activated carbons, respectively. Three well-known adsorption models, namely the Langmuir, Freundlich and Redlich–Peterson equations were tested with the experimental MB adsorption isotherms, and the results showed that the Redlich–Peterson model provided the overall best fitting of the isotherm data. In addition, the maximum capacity for MB adsorption of 1000 mg/g was achieved with the mesoporous carbon having the largest surface area and pore volume. The initial pH of MB solution had virtually no effect on the adsorption capacity and removal efficiency of the methylene blue dye. Increasing temperature over the range from 35 to 55 °C increased the adsorption of methylene blue, presumably caused by the increase in the diffusion rate of methylene blue to the adsorption sites that could promote the interaction frequency between the adsorbent surface and the adsorbate molecules. Overall, the high surface area mesoporous carbon was superior to the microporous carbon in view of the adsorption kinetics and capacity, when both carbons were used for the removal of MB from an aqueous solution.     

Synthesis of 3D porous ferromagnetic NiFe2O4 and using as novel adsorbent to treat wastewater

Three dimensions (3D) porous NiFe(2)O(4) is synthesized by a sol-gel method using egg white. The obtained NiFe(2)O(4) shows both good ferromagnetic properties and high adsorption capacity. The porous NiFe(2)O(4) shows good adsorption properties for organic dyes (Methylene Blue (138.50 mg/g), Fuchsine Red (14.61 mg/g), Methyl Violet (19.06 mg/g)) and heavy metal ions (Cu (II) (55.83 mg/g), Cr (VI) (36.95 mg/g) and Ni (II) (37.02 mg/g)) due to its 3D interconnected porous structure. The maximum adsorption of Methylene Blue (MB) fit the pseudo-second-order model and Langmuir isotherm equation well. More interestingly, the ferromagnetic NiFe(2)O(4) can be separated under a magnetic field conveniently and keeps high removal efficiency (>97%) during seven reusable cycles. These results suggest that the porous NiFe(2)O(4) is a promising favorable and reusable adsorbent.     

Selective and effective adsorption of methyl blue by barium phosphate nano-flake

We report the synthesis of barium phosphate (BP) nano-flake and its adsorption behavior to methyl blue (MB) in aqueous solution. The as-obtained BP nano-flake revealed pure rhombohedral crystal structure. The adsorption capacity of MB onto BP reached 1500mgg(-1). The adsorption equilibrium results fitted well with the Freundlich isotherm model. The adsorption process took less than 30min to reach equilibrium. The adsorption kinetics was elucidated by the pseudo-second-order kinetic equation. It followed 2-stage and 3-stage intra-particle diffusion models for the low and high concentration of dye solutions, respectively. The adsorption of MB using the BP nano-flake was highly selective, compared with the adsorption of other dyes. The interactions between MB and BP were mainly the ionic interaction and hydrogen bonds, which were confirmed by the X-ray photoelectron spectroscopic results and the density functional theory calculations. The BP nano-flake revealed less than 5% decrease in adsorption amount when it was recycled and reused five times. The present work shows that the BP nano-flake is promising for practical applications in MB removal from aqueous solutions.     

Adsorption of cationic methylene blue dye using microwave-assisted activated carbon derived from acacia wood: Optimization and batch studies

This study assesses the performance of optimized acacia wood-based activated carbon (AWAC) as an adsorbent for methylene blue (MB) dye removal in aqueous solution. AWAC was prepared via a physicochemical activation process that consists of potassium hydroxide (KOH) treatment, followed by carbon dioxide (CO₂) gasification under microwave heating. By using response surface methodology (RSM), the optimum preparation conditions of radiation power, radiation time, and KOH-impregnation ratio (IR) were determined to be 360 W, 4.50 min, and 0.90 g/g respectively, which resulted in 81.20 mg/g of MB dye removal and 27.96% of AWAC’s yield. Radiation power and IR had a major effect on MB dye removal while radiation power and radiation time caused the greatest impact on AWAC’s yield. BET surface area, mesopore surface area, and pore volume of optimized AWAC were found to be 1045.56 m²/g, 689.77 m²/g, and 0.54 cm³/g, respectively. Adsorption of MB onto AWAC followed Langmuir and pseudo-second order for isotherm and kinetic studies respectively, with a Langmuir monolayer adsorption capacity of 338.29 mg/g. Mechanism studies revealed that the adsorption process was controlled by film diffusion mechanism and indicated to be thermodynamically exothermic in nature.