超支化聚硅氧烷的紫外光固化行为及固化动力学研究

采用等温差示光量热技术(DPC)研究了超支化聚硅氧烷的紫外光固化行为及固化动力学. 探索了引发剂浓度、 光强度、 聚合温度和环境气氛对固化行为的影响规律. 研究结果表明, 增加光引发剂浓度和光强度及提高环境温度均可提高其固化速率和双键最终转化率. 在空气中固化时存在氧阻聚现象, 增大光强度可以显著缩短诱导期. 运用带扩散因子的自催化固化动力学模型研究了其光固化动力学, 计算出特定条件下的光固化动力学参数, 反应总级数约为6—7, 表观活化能为9.95 kJ/mol. 通过超支化聚合物与两种结构类似的低官能度单体光固化行为的对比, 研究了超支化聚合物固化行为与其分子结构的关系, 发现由于超支化大分子的独特结构, 在固化初始阶段便产生凝胶, 因此双键的最终转化率偏低.     

用ATRP法构筑核壳型梯度极性的多羟基多臂星状超支化聚合物及聚合物刷——三层聚合物刷的合成与表征

设计并通过原子转移自由基聚合方法 (ATRP)合成了核壳型具有梯度极性的多羟基多臂星状聚合物刷 .端羟基超支化聚 (3 乙基 3 羟甲基氧杂环丁烷 )与 2 溴 异丁基酰溴反应制得大分子引发剂 (HP Br) ,以Cu(I)Br和N ,N ,N′ ,N′ ,N″ 五甲基二乙基三胺 (PMDETA)为催化体系 ,进行甲基丙烯酸甲酯 (MMA)的ATRP反应 ,得到以甲基丙烯酸甲酯为臂的多臂星状超支化聚合物 (HP g PMMA) .又以HP g PMMA为引发剂 ,进行甲基丙烯酸羟乙酯 (HEMA)的ATRP聚合 ,得到核壳型具有梯度极性的多羟基多臂星状超支化聚合物 (HP g PMMA b PHEMA) ,继续将其羟基官能团溴代化 (与 2 溴 异丁基酰溴反应 ) ,引发HEMA的ATRP溶液聚合 ,得到了多臂星状超支化聚合物刷 .产物的结构用1 H NMR、FTIR、GPC等进行了表征和测试 .     

用ATRP法构筑核壳型梯度极性的多羟基多臂星状超支化聚合物及聚合物刷——双层聚合物刷的合成与表征

设计并通过原子转移自由基聚合方法 (ATRP)合成了核壳型多羟基多臂星状超支化聚合物刷 .以 2 溴异丁基酰溴封端的超支化聚 (3 乙基 3 羟甲基氧杂环丁烷 ) (HP Br)作为大分子引发剂 ,采用Cu(I)Br和N ,N ,N′ ,N′ ,N″ 五甲基二乙基三胺 (PMDETA)催化体系 ,在丁酮与丙醇的混和溶液中 ,通过甲基丙烯酸羟乙酯(HEMA)的ATRP溶液聚合 ,得到了一系列含有大量羟基的多臂星状超支化聚合物刷 (HP g PHEMA) ,并考察了其羟基的活性 ,发现羟基还可以与苯甲酰氯发生反应 .产物的结构和热性能用1 H NMR、FTIR、GPC、TGA、DSC等进行了表征和测试 .     

超支化聚对氯甲基苯乙烯修饰碳纳米管表面的研究

用原子转移自由基聚合(ATRP)与自缩合乙烯基聚合(SCVP)相结合合成超支化聚合物聚对氯甲基苯乙烯(PCMS),该聚合物每个分枝均以卤素原子封端. 用叠氮化反应将卤素原子转换为—N3. 通过—N3与单壁或复壁碳纳米管反应将超支化聚合物接到碳纳米管的表面上, 实现了碳纳米管的化学修饰. 通过FTIR, XPS, TEM和Raman光谱等证明PCMS是以共价键形式结合到碳纳米管表面上的. 利用TGA估算出碳纳米管表面的修饰密度, 证明用超支化结构大量的端基可反应的官能团可以改善聚合物对碳纳米管的修饰效果.     

通过自缩合乙烯基氧阴离子聚合制备超支化聚甲基丙烯酸羟丙酯

由甲基丙烯酸羟丙酯通过自缩合乙烯基氧阴离子聚合(self-condensing vinyl oxyanionic polymerization)制备了端羟基的超支化聚甲基丙烯酸酯. 以氢化钾(KH)和冠醚的复合物为引发剂时, 可以得到高分子量的聚合物. 用¹H NMR和¹³C NMR谱图证实了聚合物的超支化结构. 由于在聚合过程中存在质子转移反应, 引发剂与单体的摩尔比会影响所得聚合物的结构. 超支化聚合物的玻璃化转变温度在58.1～81.4 ℃之间, 且随着引发剂与单体的比例的减小而降低. 当引发剂与单体等摩尔比时, 所得聚合物的支化度为0.49.     

超支化烯丙基聚硅氮烷-巯基化合物体系紫外光固化研究

采用等温差示光量热扫描技术(DPC)研究了超支化烯丙基聚硅氮烷-巯基化合物体系的紫外光固化.对比了超支化聚合物-巯基化合物体系、二官能烯丙基硅氮烷-巯基化合物体系和超支化自聚体系的紫外光固化特性,结果表明超支化-巯基化合物体系可在引发剂浓度低(0.1wt%)、辐照强度低(5mW/cm2)的情况下迅速发生光固化反应;与超支化自聚反应相比固化速率高、双键转化率高;而与低官能-巯基化合物体系相比,由于超支化分子结构的独特性,导致固化速率快,双键转化率偏低.对引发剂浓度、辐照强度和反应温度对固化行为的影响表明,在引发剂浓度不超过0.5wt%和辐照强度不大于30.50mW/cm2时,反应速率分别与引发剂浓度和辐照强度的1/2次方成线性关系.运用带扩散因子的自催化固化动力学模型研究了不同温度下的固化行为,计算出特定条件下的光固化动力学参数,表观总反应级数约为8.76,表观活化能为13.97kJ/mol.     

基于炔类单体的点击聚合制备超支化聚合物

超支化聚合物由于其独特的树枝状结构和物理化学性质,已经得到了广泛关注及应用.而基于炔类单体的点击聚合作为一类简单、高效的聚合反应已被广泛用于超支化聚合物的制备.本文对近5年利用叠氮-炔和巯基-炔点击聚合制备超支化聚合物的工作进行了简要综述.其中,Cu(I)催化的叠氮-炔点击聚合可制备1?4-立构规整的超支化聚三唑;Ru(II)催化的叠氮-炔点击聚合可制备1?5-立构规整的超支化聚三唑;活化的炔类单体和叠氮单体的无金属催化点击聚合可得到1?4-异构体含量高(高达91.7%)的超支化聚合物;而光引发?热引发及自发的巯基-炔点击聚合可制备含硫的超支化聚合物.此外,对所制备的超支化聚合物的功能和应用进行了简单介绍,最后还简单讨论了点击聚合制备超支化聚合物方面的可能发展方向.     

在四官能团引发剂存在下的自缩合乙烯基聚合反应制备丙烯酸酯类超支化共聚物

超支化聚合物具有特殊的结构和性能 ,可通过一步法聚合直接制得 ,具有大规模工业应用前景 .近年来 ,超支化聚合物的研究已成为高分子科学的热门课题之一[1～ 3 ] .超支化聚合物的一个主要缺点是它的分子量分布比较宽 .Ｍ櫣ｌｌｅｒ[4] 等通过理论计算指出 ,在聚合体系中加入ｆ个功能基团的分子Ｂｆ[对自缩合乙烯基聚合反应 (ＳＣＶＰ) ,Ｂｆ为ｆ个引发基的引发剂 ;对ＡＢｘ 型单体的缩聚反应 ,为有ｆ个Ｂ官能团的分子 ],可以降低超支化聚合物的分子量分布 ,这一结果已被实验证实[5～ 7] .我们用ＭｏｎｔｅＣａｒｌｏ方法模拟了在多官能团引…     

功能超支化聚合物的制备及应用

超支化聚四氮唑表现出良好的导电性；半结晶超支化聚（酯-酰胺）具有合适的T_g和T_m，可以用于光固化粉末涂料中；含叔胺和硫醚的超支化大分子光引发剂有着良好的光引发活性。本文将主要从这3个方面综述超支化聚合物在新材料领域的应用。     

壳层悬挂β-环糊精单元的两亲性超支化聚合物的分子包合与识别行为

采用紫外分光光度法研究了两种壳层悬挂β-环糊精单元的两亲性超支化聚合物在缓冲溶液(25 ℃, pH=11)中的分子包合与识别行为. 结果表明, 两种聚合物具有来自环糊精单元和两亲性超支化聚合物的双重包合能力, 可分别与水溶性染料分子酚酞(PP)、甲基橙(MO)、有机小分子对硝基苯酚(p-NP)等3种客体分子发生单客体包合效应, 而且其包合能力强于单一的环糊精或两亲性超支化聚合物; 通过客体分子PP和MO证实了这两种聚合物还具有双重识别能力, 可以与PP和MO发生双客体包合效应.     

Influence of temperature and light intensity on the photocuring process and kinetics parameters of a pigmented UV curable system

The photopolymerization of pigmented coatings is a great challenge and hardly investigated in the literature. Therefore, in this work, the effect of photopolymerization temperature and light intensity on the curing behavior of a TiO₂-pigmented UV curable epoxy acrylate system was investigated by using photo-differential scanning calorimetry (photo-DSC) analysis. The rate of conversion and ultimate conversion at four different temperatures (i.e., 25, 45, 65, and 85 °C) and four light intensities (i.e. 2, 20, 40 and 80 mW cm^?2) for unpigmented and pigmented formulations were measured. The effect of photo-polymerization temperature and light intensity on the kinetics constants was also evaluated. It was observed that the rate of conversion and final conversion values were affected by the temperature and UV-light intensity. It was seen that the rate of conversion and ultimate conversion had their maximum values at 65 °C for unpigmented formulations. However, in pigmented formulations, these two parameters improved by increasing the temperature even up to 85 °C. Increasing the temperature caused an increase in the amount of propagation and termination rate constants in both pigmented and unpigmented formulations although the changes in the pigmented formulation were more pronounced. It was observed that the rate of polymerization and ultimate conversion for unpigmented formulations increased by increasing the light intensity up to 20 mW cm^?2 and then decreased. On the other hand, it was found that these two parameters increased by increasing light intensity up to 40 mW cm^?2 when pigmented formulations used. Finally, the dependence of termination and propagation kinetics constants on light intensity was established for both unpigmented and pigmented coatings.     

Four-center type photopolymerization in the solid state. II. Polymerization mechanism of 2,5-distyrylpyrazine

The polymerization mechanism of trans,trans-2,5-distyrylpyrazine (DSP) has been investigated and some crystal changes along with the polymerization process have been observed through polarizing microscope and x-ray diffraction pattern. Information has been obtained on the active species, polymerization reaction type, and other factors such as light intensity, reaction temperature, or crystalline state. The polymerization of DSP occurs only in the solid state by photoirradiation. Reduced viscosity increases gradually with the increase of conversion and increases sharply above 80% conversion. Polymerization rate increases with the increase of light intensity and temperature. On the other hand, reduced viscosity decreases with the increase of temperature but does not depend on light intensity within the range investigated. The polymer obtained at low conversion as well as at high conversion has high crystallinity, and the direction of polymer axes is simply related to that of monomer crystal. It was concluded that the four-center type polymerization of DSP proceeds topochemically by a photochemically induced stepwise mechanism.     

Off‐lattice Monte Carlo simulation of hyperbranched polymers, 1 Polycondensation of AB2 type monomers

The polycondensation of hyperbranched polymers, based on AB₂ type monomers, was simulated using an off‐lattice Monte Carlo method in order to investigate the polymerization kinetics and microstructures of hyperbranched polymers. The effects of temperature and activation energy of reaction on the conversion rate seem qualitatively acceptable, indicating that our simulation model properly describes the polymerization reaction of hyperbranched polymers. Number average degree of polymerization and polydispersity index were calculated as a function of conversion and compared with Flory's expectation. Fractions of dendritic, linear and terminal unit were also determined from simulation and compared with theoretical predictions. As the hyperbranched polymer grows, it is observed that the molecular shape changes from a regular fan‐shape structure to an edge‐curled up structure.     

多官能团单体对超支化聚酰胺酯光固动力学及其固化膜热性能的影响

以1,1,1-三羟甲基丙烷为核,4-N,N-（2-羟乙基）-4-酮丁酸为单体,按照 一定比例,合成理论上第二代羟端基超支化聚酰胺酯,再与丙烯酰氯反应获得丙烯 酸化超支化聚酰胺酯预聚物（HAPAE-2-A）,它在光引发剂存在下经紫外光辐照可 以快速固化成膜。根据~1H NMR 谱测定所得产物的反应程度为85%。采用凝胶渗透 色谱和气相渗透法测定所得产物的分子量分布和数均分子量分别为2.16和1620 g/mol,与其理论分子量相比,其反应程度为89%,从而估算产物实际端基丙烯酸 酯双键数为10左右。采用光-差热分析仪研究HAPAE-2-A的反应动力学,发现当体系 中加入多官能团单体,如三羟甲基丙烷三丙烯酸酯、己二醇二丙烯酸酯和乙氧基一 缩二乙二醇丙烯酸酯时,多官能团单体的官能度及含量会对体系的最大光聚合反应 速率和不饱和双键的反应程度产生较大的影响。通过动态力学热性能测试发现 HAPAE-2-A光固化膜的玻璃态转化温度随多官能团单体的加入而提高。     

Specific thermoresponsive behaviours exhibited by optically active and inactive phenylalanine modified hyperbranched polyethylenimines in water

Optically active and inactive hyperbranched polymers with specific thermoresponsive behaviours in water were reported.Through two steps hyperbranched polyethylenimine (HPEI) polymers terminated with different amount of D-phenylalanine (D-Phe),L-phenylalanine (L-Phe) or DL-phenylalanine (DL-Phe) were prepared and characterized.The analyses on the solution properties by turbidimetry,dynamic light scattering,fluorescence probe and 1H-NMR demonstrated that all the polymers exhibited specific thermoresponsive behaviours in water,including:(1) In the dilute polymer concentration region,increasing the polymer concentration led to the increase of phase transition temperature;(2) The optically inactive thermoresponsive hyperbranched polymers showed a higher cloud-point temperature (Tcp) than their corresponding optically active ones in a relatively higher polymer concentration;(3) At the same polymer concentration the hydrophobic groups of the optically inactive HPEI-DL-Phe formed more perfect hydrophobic domain than those of the optically active HPEI-L-Phe and HPEI-D-Phe.     

Synthesis and characterization of highly stable blue‐light‐emitting hyperbranched conjugated polymers

Polyfluorene homopolymer ( P1 ) and its carbazole derivatives ( P2 – P4 ) have been prepared with good yield by Suzuki coupling polymerization. P2 is an alternating copolymer based on fluorene and carbazole; P3 is a hyperbranched polymer with carbazole derivative as the core and polyfluorene as the long arms; P4 is a hyperbranched polymer with carbazole derivative as the core and the alternating fluorene and carbazole as the long arms. These polymers show highly thermal stability, and their structures and physical properties are studied using gel permeation chromatography, ¹H NMR, ¹³C NMR, elemental analysis, Fourier transform infrared spectroscopy, thermogravimetry, UV–vis absorption, photoluminescence, and cyclic voltammetry (CV). The influence of the incorporation of carbazole and the hyperbranched structures on the thermal, electrochemical, and electroluminescent properties has been investigated. Both carbazole addition and the hyperbranched structure increase the thermal and photoluminescent stability. The CV shows an increase of the HOMO energy levels for the derivatives, compared with polyfluorene homopolymer ( P1 ). The EL devices fabricated by these polymers exhibit pure blue‐light‐emitting with negligible low‐energy emission bands, indicating that the hyperbranched structure has a strong effect on the PLED characteristics. The results imply that incorporating carbazole into polyfluorene to form a hyperbranched structure is an efficient way to obtain highly stable blue‐light‐emitting conjugated polymers, and it is possible to adjust the property of light‐emitting polymers by the amount of carbazole derivative incorporated into the polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 790–802, 2008     

Temperature- and pH-responsive star amphiphilic block copolymer prepared by a combining strategy of ring-opening polymerization and reversible addition-fragmentation transfer polymerization

The star-shaped poly(ε-caprolactone)-b-poly(2-(dimethylamino)ethyl methacrylate) (HPs-Star-PCL-b-PDMAEMA) was synthesized by ring-opening polymerization and reversible addition-fragmentation chain transfer (RAFT) polymerization. Star-shaped polycaprolactones (HPs-Star-PCL) were synthesized by the bulk polymerization of ε-caprolactone (CL) with a hyperbranched polyester initiator and tin 2-ethylhexanoate as a catalyst. The number-average molecular weight of these polymers linearly increased with the increase of the molar ratio of CL to hyperbranched initiator. HPs-Star-PCL was converted into a HPs-star-PCL-RAFT by an esterification of HPs-Star-PCL and 4-cyanopentanoic acid dithiobenzoate. Star amphiphilic block copolymer HPs-Star-PCL-b-PDMAEMA was obtained via RAFT polymerization of 2-(dimethylamino)ethyl methacrylate (DMAEMA). The molecular weight distribution of HPs-Star-PCL-b-PDMAEMA was narrow. Furthermore, the micellar properties of HPs-Star-PCL-b-PDMAEMA in water were studied at various temperatures and pH values by means of dynamic light scattering (DLS). The results indicated that the star copolymers had the pH- and temperature-responsive properties. The release behaviors of model drug aspirin from the star polymer indicated that the rate of drug release could be effectively controlled by pH value and temperature.     

可聚合型光引发剂4-丙烯酰氧基二苯甲酮的光聚合性能研究

以实时红外光谱(RT-IR)法研究了合成的4-丙烯酰氧基二苯甲酮(4-ABP)的光聚合动力学性质,考察了不同单体、不同引发剂和助引发剂浓度、不同光强对聚合性能的影响.以萃取法对比研究了4-ABP和二苯甲酮(BP)在固化膜中的的残留量.结果表明,4-ABP是一种非常有效的光引发剂.随着引发剂浓度和光强的增大,单体转化率、最大反应速率都增大,诱导期缩短.萃取实验表明4-ABP在固化膜中的残留量远低于BP.     

A_2和B_3单体重氮偶合反应制备超支化偶氮聚合物

利用A2/B3单体通过重氮偶合反应制备了超支化偶氮聚合物.利用核磁共振、红外光谱、紫外光谱和DSC热分析手段表征了聚合物的结构、光谱性能和玻璃化转变温度.合成的超支化偶氮聚合物具有很好的光响应性能,用488nm Ar+激光对超支化偶氮聚合物薄膜进行光加工,得到了规则的表面起伏光栅.