聚丙烯/无机纳米粒子复合材料的发泡行为

利用型腔体积可控注塑发泡装备制备聚丙烯/无机纳米粒子微发泡复合材料,通过复合材料的流变行为和结晶行为,分析了无机纳米粒子对聚丙烯发泡行为的影响。结果表明:无机纳米粒子有促进气泡异相成核作用,同时无机纳米粒子引入可以提高聚丙烯黏弹响应和降温结晶起始温度,起到了抑制泡孔结构恶化的作用,显著改善了聚丙烯的泡孔结构;在聚丙烯材料中添加纳米CaCO3、纳米OMMT、纳米SiO2进行发泡,以PP/OMMT发泡材料的发泡质量最理想,其泡孔密度和尺寸分别为2×106个/cm3和24.2μm。     

Foaming behavior,cellular structure and physical properties of polybenzoxazine foams

In this paper, polymer foams based on a benzoxazine resin have been successfully prepared using azodicarbonamide (ADC) as a chemical blowing agent and have been characterized regarding their foaming behavior, cellular structure, and physical properties. The effect of the ADC on the curing process of the resin was analyzed using differential scanning calorimetry and blowing agent decomposition was followed by thermogravitmetric analysis (TGA). The characterization of the cellular structure of the foamed samples was done using scanning electron microscopy. The mechanical properties of the foams were determined using compression tests and the thermal conductivity was assessed using the transient plane source method. The results indicated that the curing process and gas release took place in a similar time interval. The foams showed an isotropic cellular structure with relative densities in the range 0.35–0.60, and showed compressive strengths and compressive moduli in the range of 10–70 MPa and 400–1100 MPa, respectively. Thermal conductivities were in the range of 0.06–0.12 W m^?1K^?1. The findings in this paper demonstrate the possibility of producing polybenzoxazine foams using a simple process in which curing and foaming take place simultaneously. In addition, the mechanical characterization of these materials indicates that they are suitable for structural applications. Copyright © 2011 John Wiley & Sons, Ltd.     

Calorimetric analysis of the crystallization of PBT considering the dynamic cooling condition of real processing

The crystallization behavior of polymers is usually investigated by the Differential Scanning Calorimetry (DSC) under isothermal or non-isothermal conditions, the latter one at constant cooling rates. The results of such experiments are used to calculate the crystallization during the dynamic cooling of processing, for instance with the Nakamura crystallization model. In contrast, in this article the crystallization of Polybutylene Terephthalate (PBT) was measured directly calorimetrically at dynamic cooling. For this purpose, the Fast Scanning Calorimetry (FSC) was used in particular, which can perform fast changes in scan rates. With this new approach, for example, the crystallinity can be determined across the part thickness, without calculating it with a crystallization model. At the same time, the subsequent melting behavior of structures formed during dynamic cooling was investigated. Thus a better interpretation of the first heating run of processed samples is possible.     

Crystallization behavior and morphology of poly(butylene succinate) modified with rosin maleopimaric acid anhydride

The melting behavior, crystallization behavior, and morphology of PBSR, which is Poly(butylene succinate) modified with rosin maleopimaric acid anhydride (RMA), were investigated with differential scanning calorimetry (DSC) and polarized optical microscope (POM). The multiple endotherms were ascribed to the recrystallization during DSC measurement and the equilibrium melting temperature determined by the Peak L, which was associated with the fusion of the crystals grown by normal primary crystallization, was 125.9 °C. After the kinetic parameters for isothermal crystallization of PBSR were determined by Avrami equation, to make a detailed regime transition analysis, the well‐established Lauritzen–Hoffman equation was employed. The results indicated that there were two regimes, regime II and regime III, in the range of higher and lower crystallization temperature, respectively. The regime transition temperature is about 81 °C. At last, the spherulitic morphologies of PBSR after being crystallized isothermally at different temperature were observed with the help of POM. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2694–2704, 2005     

Alkyl chains length dependent fluorescence emission and reversible mechanofluorochromism of AIEE-based quinoline derivatives

Five quinoline derivatives containing different alkyl chains (QLACn, n?=?2, 4, 6, 8, 12) were synthesized to investigate the effect of alkyl chains on their photophysical properties. The fluorescent properties of the QLACn were affected by the alkyl chains, which indicated obvious blue-shifting trend and fluorescence emission are alkyl chains length-dependent by grinding-induced spectral shifts (Δλ_MFC). Longer alkyl-length revealed larger Δλ_MFC. Powder X-ray diffraction (PXRD), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC) measurements indicated that the transformation between microcrystalline and amorphous states upon external stimuli should be responsible for the observed reversible MFC behavior.     

Synthesis and characterization of new aromatic polyesters and polyethers derived from 1,2-bis(4-hydroxyphenyl)-1,2-diphenylethylene

New polyarylates and aromatic polyethers were synthesized from 1,2-bis(4-hydroxyphenyl)-1,2-diphenylethylene, and aromatic dicarboxylic acid chlorides and aromatic dihalides, respectively. The polyarylates having inherent viscosities of 0.28–1.05 dL/g were synthesized by either the two-phase method or the high-temperature solution method. All the polymers were easily soluble in N-methyl-2-pyrrolidone, N,N-dimethylformamide, pyridine, m-cresol, 1,4-dioxane, and 1,1,2,2-tetrachloroethane. They have glass transition temperatures in the range of 217–250°C and showed no weight loss below 315°C in both air and nitrogen atmospheres. Aromatic polyethers with inherent viscosities of 0.85–1.21 dL/g were obtained by the polycondensation of 1,2-bis(4-hydroxyphenyl)-1,2-diphenylethylene and aromatic difluorides in the presence of potassium carbonate. These polymers having glass transion temperatures of 193–220°C were also soluble in the aforementioned solvents and stable up to around 350deg;C in both atmospheres. © 1994 John Wiley & Sons, Inc.     

Effect of Mineral Salts on Steady Rheological Properties of Nonionic Hydrophobically Modified Polyacrylamide and Its Stress-Relaxation Behavior

A micelle-forming polymerizable surfactant monomer, octylphenol polyoxyethylene acrylate (OP-10-AC), was synthesized, and then OP-10-AC was copolymerized with acrylamide (AM) to form nonionic hydrophobically modified polyacrylamide P(AM/OP-10-AC) through micellar copolymerization. In the absence of surfactants, it was investigated in detail that the effect of mineral salts and temperature on steady rheological properties of P(AM/OP-10-AC) solutions and the effect of concentrations on reduced viscosity of P(AM/OP-10-AC) in a dilute solution. The results indicate that concentrations of the copolymer, mineral salts and temperature had a strong influence on shear viscosity of P(AM/OP-10-AC) solutions, and the trend of reduced viscosity of P(AM/OP-10-AC) solutions was distinctly different from polyacrylamide with increasing concentrations of testing solutions. In addition, it was also investigated that stress-relaxation behavior of an aqueous solution of P(AM/OP-10-AC)/KCl. As a result, a stress-relaxation model of the copolymer solutions was proposed, which can further verify the correctness of the conclusion on stress-relaxation behavior of hydrophobic association hydrogels in the paper reported previously.     

电响应聚合物薄膜的表面图案化

研究了炭黑(CB)和石墨(GP)填充高密度聚乙烯(HDPE)复合体系的动态流变行为.发现高填料含量时出现似固体行为,并认为它归因于无机粒子网络逾渗结构的形成.在相同聚合物基体条件下,粒子种类和粒子几何参数(粒子形状、大小、粒径分布)对低频区域流变行为、流变参数的逾渗行为和逾渗阈值(φc)有决定性影响,且种类的影响相比于粒子几何参数更为显著.此外,高表面活性及高比表面积(大径厚比、小尺寸)粒子填充体系具有较低的φc.     

The Use of Pressure-Volume-Temperature Measurements in Polymer Science

The importance of the knowledge of thermodynamic parameters from p-V-T experiments is shown in different fields of polymer science with special emphasis on determination of the phase behaviour of polymer systems.     

粒子填充HDPE复合体系动态流变行为研究

研究了炭黑(CB)和石墨(GP)填充高密度聚乙烯(HDPE)复合体系的动态流变行为.发现高填料含量时出现似固体行为,并认为它归因于无机粒子网络逾渗结构的形成.在相同聚合物基体条件下,粒子种类和粒子几何参数(粒子形状、大小、粒径分布)对低频区域流变行为、流变参数的逾渗行为和逾渗阈值(φ_c)有决定性影响,且种类的影响相比于粒子几何参数更为显著.此外,高表面活性及高比表面积(大径厚比、小尺寸)粒子填充体系具有较低的φ_c.     

嵌段共聚物熔体流变行为研究进展

微相分离的结构特点赋予了嵌段共聚物很多优异的性能,使其广泛应用于汽车部件及工具手柄、电线电缆包皮或绝缘带、医疗制品及食品容器、密封胶、粘合剂、涂料以及聚合物共混改性等领域。聚合物流变特性直接关系到材料加工参数的选择以及产品最终性能,是聚合物结构设计、材料加工参数优化选择及拓展产品应用领域的理论基础。本文对嵌段共聚物的熔体流变行为进行了综述,着重介绍了与嵌段共聚物特殊结构相对应的流变特性,以及流变特性与相行为之间的关联,并提出了嵌段共聚物熔体流变行为研究的前沿与重点。     

正、负离子表面活性剂混合水溶液的相行为

通过对混合系统相行为的研究，总结出正、负离子表面性剂混合体系普遍存在三上浓度区的规律，即在低浓度与高浓度时为透明均相溶液，中间浓度区为复相体系，而且表明，随极性基体积增大，混合体系形成均相溶液的能力增加；在高浓度区，疏水链长短对混合体系形成均相溶液能力的影响与低浓度区的情况不完全一致，有时会出现疏水链较短的体系形成均相溶液的能力反而较差的“反常”现象。     

Effect of core group substituents on the monomer mesophase,photocuring, and film viscoelastic properties of mesogenic diacrylates

In this paper, the influence of molecular structure variations on the mesophase behavior, photocurability, and film properties of polymerizable mesogenic diacrylates is reported. The effect of methoxy or chloro substituent on the mesophase behavior of the monomers, present at the 2‐position of the phenylene core, in comparison to the unsubstituted core, has been studied using thermal and photo‐DSC techniques. These monomers were used in combination with a chiral dopant to form cholesteric mesophases, which was subsequently crosslinked through photopolymerization. Optical microscopy and polarized optical microscopy (POM) were used to study the morphology of monomers as well as the photopolymerized films. Optical images show the influence of chiral dopant on the texture present in the films, both before and after the crosslinking. POM images show the mesophase present in the monomers and the free films. Evaluation of viscoelastic properties of the photocured films demonstrates the influence of mesogenic core substituents on the network transition temperature, modulus, and damping characteristics. Copyright © 2008 John Wiley & Sons, Ltd.     

P[MMA-IL]修饰石墨烯协同调控PVDF复合物结晶与介电行为

为改善石墨烯(Gra)在聚偏氟乙烯(PVDF)中的分散性和界面性质,以甲基丙烯酸甲酯(MMA)和1-乙烯基-3-乙基咪唑溴盐(IL)为单体合成P[MMA-IL]共聚物,用于修饰石墨烯(Gra),并通过溶液共混、热压法制备PVDF/PMMA、PVDF/P[MMA-IL]、PVDF/PMMA/Gra和PVDF/P[MMA-IL]/Gra复合薄膜.采用Raman光谱、场发射扫描电子显微镜(FESEM)、傅里叶变换反射红外光谱分析仪(FTIR-ATR)、X射线衍射仪(XRD)、偏光显微镜(POM)、示差扫描量热仪(DSC)和电感电容电阻测试仪(LCR)对复合薄膜的结构形态、结晶与介电行为进行表征和分析.Raman光谱表明P[MMA-IL]与Gra之间存在强相互作用;FESEM照片显示P[MMAIL]能够促进Gra在基体中的分散;DSC、XRD和FTIR-ATR数据表明PMMA降低PVDF的结晶温度,PMMA和Gra未能诱导出?-PVDF极性晶体,而单独的P[MMA-IL]会通过咪唑阳离子-偶极子作用诱导?-PVDF晶体;通过咪唑阳离子-π强相互作用,P[MMA-IL]在模板剂Gra表面进行修饰,协同诱导作用增强.POM照片表明?-PVDF晶体在生长过程中,MMA链段会嵌入到球晶的晶片空隙中,引起结构疏松;离子-偶极子和IL成核作用导致?-PVDF晶体尺寸较小,结晶较快.介电行为研究表明PMMA及其修饰Gra降低PVDF的结晶度和链浓度,导致界面极化和取向极化较弱,介电响应较弱;而P[MMA-IL]修饰Gra诱导的?-PVDF晶体、以及IL链段在界面的离子极化使得界面极化作用增强,介电响应增强.     

A closed-loop behavior of ternary polymer blends composed of three miscible binaries

Poly (methyl methacrylate) (PMMA) was known to be miscible with poly (vinyl phenol) (PVPh). According to literature, poly (vinyl cinnamate) (PVCN) was also miscible with PVPh. The miscibility between PMMA and PVCN was corroborated on the basis of preliminary experiments. Is a ternary blend consisting of PMMA, PVPh and PVCN miscible in all the blend compositions? To answer this question, the miscibility of this ternary was examined in different blend compositions mainly based on calorimetry data in this investigation. The results using two different molecular weights of PVPh demonstrated an interestingly closed-loop behavior of immiscibility. The reason is likely because of the “Δχ effect”.     

PAA对PLA流变性能和热性能的影响

通过熔融共混法制备了一系列的PLA/PAA共混物,考察了PLA/PAA共混体系的流变行为和热性能(结晶行为和热降解行为).FTIR测试结果证实PLA与PAA分子链之间形成了氢键网络.动态剪切流变测试和DSC测试均表明共混体系的流变行为和冷结晶行为会随着PAA含量的改变而改变,这可能是由于PLA与PAA的氢键作用受到PAA含量的影响.另外,DSC测试证实共混体系中的氢键网络还会受到试样热历史的影响.当PAA含量较低(低于5 wt%)时,PLA/PAA共混体系中PAA与PLA熔体两相的相分离不严重,使得PAA与PLA分子链能够较大限度地接触而形成较强的氢键作用,因而可以明显减缓增塑作用对黏度降低的影响.     

甘草酸的电化学行为研究

用循环伏安法、单扫描示波极谱法研究了甘草酸（ｇｌｙｃｙｒｒｈｉｚｉｃ，ＧＡ）在汞电极上的电化学行为及反应机理．证明甘草酸在ｐＨ＝４～１２的缓冲溶液（Ｈ３ＢＯ３＋Ｈ３ＰＯ４＋乙酸＋ＮａＯＨ）中有吸附峰，且示波极谱导数峰值与甘草酸浓度在８．３×１０－５～１．２×１０－６ｍｏｌ／Ｌ范围内成正比，使用悬汞电极（ＨＭＤＥ）线性扫描伏安法可使检测下限达２．４×１０－６ｍｏｌ／Ｌ．根据实验结果首次提出了甘草酸在汞电极上的反应机理．该机理同时被紫外光谱证明，得到合理解释     

Wetting Behavior of Tetrasiloxane Surfactants Containing Glucosamide on Low-Energy Surface

The wetting behavior of aqueous solutions of two types of siloxane surfactant (dicephalic and gemini) on two hydrophobic substrates was investigated. Solutions of dicephalic surfactant demonstrate rapid and complete wetting on Parifilm surface and only partial wetting on Teflon. An increase in surfactant concentration results in a transition from partial to complete wetting. The solutions of gemini surfactant show only partial wetting on both Teflon and Parifilm. It is demonstrated that wetting behavior depends crucially on surfactant structure; substrate surface affects the wetting behavior of siloxane surfactant.     

铁取代钨硅酸盐位置异构体的合成、表征及电化学性质

取代型杂多酸盐（ HPC）具有金属卟啉的类似结构 ,它可以代替金属卟啉在很多反应中作催化剂 [1],被称为无机金属卟啉。 Hill[2],Neumann[3]分别报道了过渡元素单取代的杂多阴离子 [PW11M(H2O)O39]n－, [SiW11Ru(H2O)O39]n－对烯烃环氧化反应具有催化活性。目前,在单取代的杂多配合物中,β异构体的报道很少,我们发现,某些单取代金属衍生物中,β异构体具有良好的催化活性,具有明显的应用前景。继过去的工作 [4],我们又研究了过渡元素取代的 11-系列杂多阴离子的某些性质。有关α-XW11Fe(H2O)O39n－（ X=Si, P, Ge, As…     

沈阳市3～6岁儿童铅污染流行情况及对行为发育的影响

为了解沈阳市 3～ 6岁儿童血铅水平、铅污染流行情况及特征 ,采用石墨炉原子吸收方法对本市 1 0 84名 3～ 6岁儿童进行血铅含量测定 ,根据美国疾病控制中心 1 991年标准将血铅水平分为六级 ,观察了不同程度铅污染与儿童行为发育的关系。结果表明 ,血铅水平为 1 0 0 1 4± 39 83μg L ,铅污染流行率为 4 4 4 6 %。儿童铅污染程度与儿童行为发育异常呈正相关。揭示我市 3～ 6岁儿童血铅水平仍处于较高水平 ,铅污染以轻度为主 ,铅污染可影响儿童行为发育