Determination of phenamacril residues in flour and rice based on Z‐Sep+ using ultra‐high‐performance liquid chromatography–tandem mass spectrometry

Phenamacril is a new broad‐spectrum fungicide that is commonly used for the control of fungal diseases in wheat and rice. In this study, ultra‐high‐performance liquid chromatography–tandem mass spectrometry was used to establish a method for analyzing the residual phenamacril in flour and rice based on the improved QuEChERS (quick, easy, cheap, effective, rugged and safe) method using Z‐Sep+ as the adsorbent in the pre‐treatment process. The average recovery of phenamacril in flour and rice was 82.2–96.0%, the relative standard deviation was 2.1–5.6% and the limit of quantification was 0.5 μg/kg. The accuracy and sensitivity of this method meet the requirements for residue analysis. The method was applied to commercially available flour and rice samples, and the detected concentrations of phenamacril were 0.005–0.033 mg/kg. This method provides technical support for the safety evaluation of phenamacril.     

Comparison of different cleanup procedures for oil crops based on the development of a trace analytical method for the determination of pyraclostrobin and epoxiconazole

The effects of different cleanup procedures in removing high‐molecular‐mass lipids and natural colorants from oil‐crop extracts, including dispersive solid‐phase extraction, low‐temperature precipitation and gel permeation chromatography, were studied. The pigment removal, lipid quantity, and matrix effects of the three cleanup methods were evaluated. Results indicated that the gel permeation chromatography method is the most effective way to compare the dispersive solid‐phase extraction and low‐temperature precipitation. Pyraclostrobin and epoxiconazole applied extensively in oil‐crop production were selected as typical pesticides to study and a trace analytical method was developed by gel permeation chromatography and ultra high performance liquid chromatography with tandem mass spectrometry. Average recoveries of the target pesticides at three levels (10, 50, and 100 μg/kg) were in the range of 74.7–96.8% with relative standard deviation values below 9.2%. The limits of detection did not exceed 0.46 μg/kg, whereas the limits of quantification were below 1.54 μg/kg and much lower than maximum residue limit in all matrices. This study may provide the essential data for optimizing the analytical method of pesticides in oil‐crop samples.     

Simultaneous quantification of three tropane alkaloids in goji berries by cleanup of the graphene/hexagonal boron nitride hybrids and ultra‐high‐performance liquid chromatography tandem mass spectrometry

A modified quick, easy, cheap, effective, rugged and safe method was established for simultaneous determination of atropine, anisodamine, and scopolamine in goji berries by using ultra‐high‐performance liquid chromatography with tandem mass spectrometry. The graphene/hexagonal boron nitride hybrids were prepared and first applied as a cleanup adsorbent. Compared to classical cleanup adsorbent (C₁₈), the graphene/hexagonal boron nitride hybrids as adsorbent had better extraction efficiency for the detection of analytes. Under the optimal conditions, the proposed analytical method achieved satisfactory linearity (R² > 0.995), and obtained desirable recoveries ranged from 77.4 to 94.0% with the relative standard deviation of 1.2–6.1% at the concentration levels of 3.2–13.4 µg/kg. The limits of quantitation of atropine, anisodamine, and scopolamine were, respectively, 3.2, 4.6, and 4.5 µg/kg with linearity ranged from 3.2 to 25.4 µg/kg. The modified quick, easy, cheap, effective, rugged, and safe sample preparation with ultra‐high‐performance liquid chromatography and tandem mass spectrometry method was successfully applied to evaluate the safety of goji berries collected from 30 plant areas in China, suggesting its applicability and suitability for the routine analysis of three tropane alkaloids in goji berries.     

A new solid-phase extraction and HPLC method for determination of patulin in apple products and hawthorn juice in China

A new solid‐phase extraction (SPE) pretreatment method using a home‐made polyvinylpolypyrrolidone‐florisil (PVPP‐F) column was developed for the analysis of patulin in apple and hawthorn products in China. Fifty samples (25 apple juices, 12 apple jams, and 13 hawthorn juices) were prepared using the new method and then analyzed by high performance liquid chromatography with diode array detection (HPLC‐DAD) on an Agela Venusil MP C₁₈ reversed‐phase column (4.6 mm × 250 mm, 5 μm). The cleanup results for all samples using home‐made PVPP‐F column were compared with those obtained using a MycoSep®228 AflaPat column. The correlation coefficient R (0.9998) fulfilled the requirement of linearity for patulin in the concentration range of 2.5–250 μg/kg. The limits of detection (LODs) and quantification (LOQs) of patulin were 3.99 and 9.64 μg/kg for PVPP‐F column, and 3.56 and 8.07 μg/kg for MycoSep®228 AflaPat column, respectively. Samples were spiked with patulin at levels ranging from 25 to 250 μg/kg, and recoveries using PVPP‐F and MycoSep®228 AflaPat columns were in the range of 81.9–100.9% and 86.4–103.9%, respectively. Naturally occurring patulin was found in 2 of 25 apple juice samples (8.0%) and 1 of 13 hawthorn juice samples (7.7%) at concentrations ranging from 12.26 to 36.81 μg/kg. The positive results were further confirmed by liquid chromatography electrospray ionization mass spectrometry (LC‐ESI‐MS).     

Rapid multiplug filtration cleanup method for the determination of 124 pesticide residues in rice,wheat, and corn

A simple and rapid multiplug filtration cleanup method based on multiwalled carbon nanotubes was developed to determine 124 pesticide residues in rice, wheat, and corn, which could be done in a few seconds without conditioning and elution steps. Various combinations of sorbents were optimized for each matrix with a dispersive solid‐phase extraction procedure to get a satisfactory recovery and clean‐up performance. Good linearity was obtained for all pesticides with calibration curve coefficients larger than 0.9958. Most recoveries for the majority pesticides were between 70 and 120% (n = 5) with relative standard deviations below 20%. The limit of detection was 0.1–1.3 μg/kg, and the limit of quantification was 0.2–4.3 μg/kg for the pesticides in all matrices. The work suggests that the multiplug filtration cleanup method is better than the dispersive solid‐phase extraction method and it could be applied to routinely monitor pesticide residues in market samples.     

Trace analysis of some organophosphorus pesticides in rice samples using ultrasound‐assisted dispersive liquid–liquid microextraction and high‐performance liquid chromatography

An ultrasound‐assisted dispersive liquid–liquid microextraction based on solidification of a floating organic drop method followed by high‐performance liquid chromatography was developed for the extraction, preconcentration, and determination of trace amounts of organophosphorus pesticides in rice samples. Variables affecting the performance of both steps were thoroughly investigated. Some effective parameters on extraction were studied and optimized. Under the optimum conditions, recoveries for rice sample are in the range of 58.0–66.0%. The calibration graphs are linear in the range of 4–800 μg/kg and, limits of detection and limits of quantification are in the range of 1.5–3 and 4.2–8.5 μg/kg, respectively. The relative standard deviation for 50.0 μg/kg of organophosphorus pesticides in rice sample are in the range of 4.4–5.1% (n = 5). The obtained results show that proposed method is a fast and simple method for the determination of pesticides in cereals.     

Analysis of amicarbazone and its two metabolites in grains and soybeans by liquid chromatography with tandem mass spectrometry

A sensitive, simple and reliable analytical method based on a modified quick, easy, cheap, effective, rugged, safe sample preparation and liquid chromatography with tandem mass spectrometry detection was developed for the simultaneous determination of amicarbazone and its two major metabolites desamino amicarbazone and isopropyl‐2‐hydroxy‐desamino amicarbazone residues in grains (rice, wheat, corn, buckwheat) and soybean. Several parameters, including liquid chromatography and tandem mass spectrometry conditions, extraction approaches and the adsorbents for clean‐up, which might influence the accuracy of the method, were extensively investigated. The established method was further validated by determining the linearity (R² > 0.99), fortified recovery (79–118%), precision (1–12%) and sensitivity (limit of quantification, 5 μg/kg for amicarbazone and desamino amicarbazone, and 10 μg/kg for isopropyl‐2‐hydroxy‐desamino amicarbazone). Finally, the established method was successfully applied to determine the residues of amicarbazone and its metabolites in 49 real samples of grain and soybean.     

Simultaneous determination of three herbicides in wheat,wheat straw,and soil using a quick,easy, cheap,effective, rugged,and safe method with ultra high performance liquid chromatography and tandem mass spectrometry

In this study, a sensitive and effective analytical method for the extraction and detection of three herbicide residues (florasulam, fluroxypyr, and halauxifen‐methyl) in wheat and soil was developed. Samples were extracted with acetonitrile/water followed by salting out, dispersive solid‐phase extraction cleanup, and detection using ultra high performance liquid chromatography coupled with tandem mass spectrometry. The target analytes were detected within a 5 min runtime using an ultra high performance liquid chromatography high‐strength silica trifunctional column connected to an electrospray ionization source in positive mode. The method was validated in five replicates at three fortification concentrations in each matrix. Adequate pesticide quantification and identity confirmation were attained, even at the lowest concentration levels. The method showed very good accuracy and precision. Good recoveries were observed for the three herbicides and mostly ranged between 75.8 and 114.6%, with intraday relative standard deviations <6.01% and interday relative standard deviations <4.02%. The limits of quantification ranged between 0.14 and 7.68 μg/kg for each herbicide. The method was successfully applied for the simultaneous analysis of the three herbicides in actual trial samples, and the results proved that the proposed method was effective in detecting these three herbicides.     

Simultaneous determination of 106 pesticides in nuts by LC–MS/MS using freeze‐out combined with dispersive solid‐phase extraction purification

As a result of the low water content and high fat matrices in nuts, it is very difficult to simultaneously determine multi‐pesticides in trace levels. Here, a sample pretreatment method was developed in which, microwave‐assisted solvent extraction was firstly used to extract pesticides, and then a two‐step cleanup method was conducted combining freeze‐out with dispersive solid‐phase extraction to remove the lipidic matrix. By this way, 106 pesticides were simultaneously determined in the complicated nut sample by using an ultra‐high pressure liquid chromatography coupled with a tandem mass spectrometer. Average recoveries were 75.3–119.3% with relative standard deviations < 14% at three concentration levels. The limits of detection and quantification were in the ranges of 0.3–3.0 and 1.0–10.0 μg/kg, respectively. Furthermore, the method was successfully applied to the determination of pesticides in 180 commercial nut samples.     

Rapid selective accelerated solvent extraction and simultaneous determination of herbicide atrazine and its metabolites in fruit by ultra high performance liquid chromatography

A selective accelerated solvent extraction procedure achieved one step extraction and cleanup for analysis of herbicide atrazine and its metabolites in fruit. Using a BEH C18 analytical column and the gradient mode with 2 mM ammonium acetate aqueous solution/acetonitrile as a mobile phase achieved effective chromatographic separation of the five analytes within 4 min. The calibration curves were linear over two orders of magnitude of concentration with correlation coefficients (r) of 0.9996?0.9999. The method limit of quantification was 1, 2, 1.5, 3, and 2 μg/kg for atrazine, desethylatrazine, desisopropylatrazine, desethyldesisopropylatrazine, and hydroxyatrazine, respectively, in the case of atrazine it is at least two orders of magnitude lower than the maximum residue limit (0.25 mg/kg). The intra‐day and inter‐day precisions of the five analytes were in the range of 2.1–3.5 and 3.1–4.8 %, respectively. The recoveries of the five analytes at three spiked levels varied from 85.9 to 107% with a relative standard deviation of 1.8–4.9% for pear and apple samples. The ultra high performance liquid chromatography with diode array detection method was proved to be fast, inexpensive, selective, sensitive, and accurate for the quantification of the analytes in pear and apple samples.     

Glass slides functionalized by 1‐carboxyethyl‐3‐methylimidazolium chloride for the determination of triazine herbicides in rice using high‐performance liquid chromatography

A novel and simple supported ionic‐liquid‐based solid‐phase extraction method for the determination of triazine herbicides in rice was developed. Glass slides were functionalized by an ionic liquid, 1‐carboxyethyl‐3‐methylimidazolium chloride, and were used for the simultaneous extraction of seven triazine herbicides in rice samples. The effects of the type of extraction solvent, the extraction time, the type and volume of loading solvent, and the type of eluting solvent on the extraction efficiency were investigated and optimized. Under the optimum operation conditions, the limits of detection for seven triazine herbicides in rice samples obtained by high‐performance liquid chromatography were 3.16–5.42 ng/g, which were lower than the maximum residue levels established by various organizations. The linear correlation coefficients were higher than 0.9975 in the concentration range of 0.015–1.08 μg/g for the seven triazine herbicides. The recoveries of the seven triazine herbicides at the two concentration levels of 0.15 and 0.45 μg/g are between 82.47 and 104.21%, with relative standard deviations of 0.69–9.19%. The intra‐ and inter‐day (n = 5) precisions for all triazine herbicides at the spiked level of 0.30 μg/g were 1.72–11.71%.     

Determination of ergot alkaloids from grains with UPLC‐MS/MS

A simple and rapid method for determining six ergot alkaloids and four of their respective epimers was developed for rye and wheat. The analytes were extracted from the sample matrix with ACN/ammonium carbonate solution. The extract was purified with a commercial push‐through SPE column (Mycosep^® 150 Ergot). After concentration and filtration steps, the final separation of the analytes was achieved with ultra‐performance LC‐MS/MS. The chromatographic separation of the ergot alkaloids was achieved in 4.5 min. The method performance proved satisfactory in the preliminary validation. The calculated LOQs were low ranging from 0.01 to 1.0 μg/kg for wheat and from 0.01 to 10.0 μg/kg for rye. At the concentration levels of 10, 50 and 200 μg/kg, the recoveries were between 80 and 120% in most cases and the within‐day repeatability (expressed as RSD) ranged between 1.3 and 13.9%. Despite the cleanup of the samples, some matrix effect was observed in the MS, highlighting the necessity of using matrix‐assisted standards. This is the first article to describe the application of the push‐through columns and ultra‐performance LC in the analysis of ergot alkaloids.     

Rapid pretreatment and determination of bisphenol A in water samples based on vortex‐assisted liquid–liquid microextraction followed by high‐performance liquid chromatography with fluorescence detection

A method for the rapid pretreatment and determination of bisphenol A in water samples based on vortex‐assisted liquid–liquid microextraction followed by high‐performance liquid chromatography with fluorescence detection was proposed in this paper. A simple apparatus consisting of a test tube and a cut‐glass dropper was designed and applied to collect the floating extraction drop in liquid–liquid microextraction when low‐density organic solvent was used as the extraction solvent. Solidification and melting steps that were tedious but necessary once the low‐density organic solvent used as extraction solvent could be avoided by using this apparatus. Bisphenol A was selected as model pollutant and vortex‐assisted liquid–liquid microextraction was employed to investigate the usefulness of the apparatus. High‐performance liquid chromatography with fluorescence detection was selected as the analytical tool for the detection of bisphenol A. The linear dynamic range was from 0.10 to 100 μg/L for bisphenol A, with good squared regression coefficient (r² = 0.9990). The relative standard deviation (n = 7) was 4.7% and the limit of detection was 0.02 μg/L. The proposed method had been applied to the determination of bisphenol A in natural water samples and was shown to be economical, fast, and convenient.     

Determination of four sulfonylurea herbicides in tea by matrix solid‐phase dispersion cleanup followed by dispersive liquid–liquid microextraction

Matrix solid‐phase dispersion combined with dispersive liquid–liquid microextraction has been developed as a new sample pretreatment method for the determination of four sulfonylurea herbicides (chlorsulfuron, bensulfuron‐methyl, chlorimuron‐ethyl, and pyrazosulfuron) in tea by high‐performance liquid chromatography with diode array detection. The extraction and cleanup by matrix solid‐phase dispersion was carried out by using CN‐silica as dispersant and carbon nanotubes as cleanup sorbent eluted with acidified dichloromethane. The eluent of matrix solid‐phase dispersion was evaporated and redissolved in 0.5 mL methanol, and used as the dispersive solvent of the following dispersive liquid–liquid microextraction procedure for further purification and enrichment of the target analytes before high‐performance liquid chromatography analysis. Under the optimum conditions, the method yielded a linear calibration curve in the concentration range from 5.0 to 10 000 ng/g for target analytes with a correlation coefficients (r²) ranging from 0.9959 to 0.9998. The limits of detection for the analytes were in the range of 1.31–2.81 ng/g. Recoveries of the four sulfonylurea herbicides at two fortification levels were between 72.8 and 110.6% with relative standard deviations lower than 6.95%. The method was successfully applied to the analysis of four sulfonylurea herbicides in several tea samples.     

Combination of dispersive solid‐phase extraction and salting‐out homogeneous liquid–liquid extraction for the determination of organophosphorus pesticides in cereal grains

A new analytical method for the determination of organophosphorus pesticides in cereal samples was developed by combining dispersive SPE (d‐SPE) and salting‐out homogeneous liquid–liquid extraction (SHLLE). The pesticides were first extracted from cereal grains with acetonitrile, followed by d‐SPE cleanup. A 2 mL aliquot of the extract was then added to a centrifuge tube containing 9.2 mL water and 3.3 g NaCl for SHLLE. Analysis of the extract was carried out by gas chromatography coupled with flame photometric detection. The d‐SPE procedure effectively provides the necessary cleanup of the extract while SHLLE is used as an efficient concentration technique. Experimental parameters influencing the extraction efficiency including amounts of added water and salt were investigated. Recovery studies were carried out at three fortification levels, yielding recoveries in the range of 57.7–98.1% with the RSD from 3.7 to 10.9%. The reported limits of determination obtained from this study were 1 μg/kg, which is better than the conventional methods. In the analysis of 40 wheat and corn samples taken from Beijing suburbs, only two wheat samples have chlorpyrifos residue over the limits of determination.     

Fe3O4 nanoparticles coated with polyhedral oligomeric silsesquioxanes and β‐cyclodextrin for magnetic solid‐phase extraction of carbaryl and carbofuran

In this study, porous sandwich structure Fe₃O₄ nanoparticles coated by polyhedral oligomeric silsesquioxanes and β‐cyclodextrin were prepared by surface polymerization and were used as the magnetic solid phase extraction adsorbent for the extraction and determination of carbaryl and carbofuran. The Fe₃O₄ nanoparticles coated with polyhedral oligomeric silsesquioxanes and β‐cyclodextrin were characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, thermogravimetric analysis, vibrating sample magnetometry, and scanning electron microscopy. After optimizing the extraction conditions, a method that combined magnetic solid phase extraction with high‐performance liquid chromatography was developed for the determination of carbaryl and carbofuran in apple. The method exhibited a good linearity in the range of 2–400 μg/kg for carbaryl and carbofuran (R² = 0.9995), respectively. The limits of detection were 0.5 μg/kg of carbaryl and 0.7 μg/kg for carbofuran in apple, respectively. Extraction recoveries ranged from 94.2 to 103.1% with the preconcentration factor of 300 and the relative standard deviations were less than 5.9%. These results indicated that the method combined magnetic solid phase extraction with high‐performance liquid chromatography and was promising for the determination of carbaryl and carbofuran at trace amounts.     

Performance comparison of dispersive solid‐phase extraction and multiplug filtration cleanup methods for the determination of tefuryltrione in plant and environmental samples using UHPLC–MS/MS

The detection frequencies of tefuryltrione, a new type of 4‐hydroxyphenyl‐pyruvate dioxygenase inhibitor herbicide, are rarely reported, probably because of the paucity of analytical methods. Herein, an effective and sensitive analytical method has been developed to detect tefuryltrione in vegetables (tomato and cucumber), cereals (rice and corn), soil, and water by ultra high performance liquid chromatography coupled with tandem mass spectrometry. Comparisons of the performances of dispersive solid‐phase extraction and multiplug filtration cleanup methods were carried out for tefuryltrione in complex matrices. Extraction solvents and purification sorbents were further optimized for dispersive solid‐phase extraction. Tefuryltrione was analyzed with electrospray ionization in the positive mode within 2.0 min. Mean recoveries for tefuryltrione were 75.4–108.9% with relative standard deviations less than 11.0% at three fortification levels (10, 100, 500 μg/kg) in the sample matrixes. Limits of quantification ranged from 0.70 to 5.12 μg/kg, and an excellent linearity (R ² ≥ 0.9902) was obtained for tefuryltrione at concentrations of 5–1000 μg/L. The results showed that the developed dispersive solid‐phase extraction method could serve as an effective, sensitive, and robust method for routine monitoring of tefuryltrione residue in plants and environmental samples.     

Determination of ethanamizuril,a novel triazine coccidiostat,in rat plasma by ultra‐performance liquid chromatography system‐tandem mass spectrometry and its application in a toxicological study

Ethanamizuril is a new triazine compound that has the potential to be a novel anticoccidial drug. Toxicological studies in experimental rats were performed to understand the safety profile of ethanamizuril for drug product development. In this study, a novel, selective and accurate ultra‐performance liquid chromatography tandem mass spectrometry method has been developed for the determination of ethanamizuril concentrations in rat plasma. With 4‐nitro‐o‐cresol as an internal standard, sample pretreatment involved a one‐step extraction with acetonitrile of 100 μL plasma. The detection was carried out by electrospray ionization mass spectrometry in negative ion mode with selected ion recording. The standard curves were linear (r² ≥ 0.999) over the concentration range of 0.1–100 μg/mL. The relative standard deviations of intra‐ and inter‐day precisions were less than 8.4 and 8.87%, respectively. The mean extraction recovery of ethanamizuril from rat plasma was 97.68–102.57%. The method was fully validated and successfully applied to monitor plasma concentrations of ethanamizuril in a short‐term toxicity study and two‐generation reproduction toxicity study. The result of the study confirmed that the elimination of ethanamizuril in rats is slow.     

Determination of 19 sulfonamides residues in pork samples by combining QuEChERS with dispersive liquid–liquid microextraction followed by UHPLC–MS/MS

A new simple and rapid pretreatment method for simultaneous determination of 19 sulfonamides in pork samples was developed through combining the QuEChERS method with dispersive liquid–liquid microextraction followed by ultra‐high performance liquid chromatography with tandem mass spectrometry. The sample preparation involves extraction/partitioning with QuEChERS method followed by dispersive liquid–liquid microextraction using tetrachloroethane as extractive solvent and the acetonitrile extract as dispersive solvent that obtained by QuEChERS. The enriched tetrachloroethane organic phase by dispersive liquid–liquid microextraction was evaporated, reconstituted with 100 μL acetonitrile/water (1:9 v/v) and injected into an ultra‐high performance liquid chromatography with a mobile phase composed of acetonitrile and 0.1% v/v formic acid under gradient elution and separated using a BHE C₁₈ column. Various parameters affecting the extraction efficiency were investigated. Matrix‐matched calibration curves were established. Good linear relationships were obtained for all analytes in a range of 2.0–100 μg/kg and the limits of detection were 0.04–0.49 μg/kg. Average recoveries at three spiking levels were in the range of 78.3–106.1% with relative standard deviations less than 12.7% (n = 6). The developed method was successfully applied to determine sulfonamide residues in pork samples.     

Simultaneous detection of multiple hydroxylated polychlorinated biphenyls from biological samples using ultra‐high‐performance liquid chromatography with isotope dilution tandem mass spectrometry

We established a method for the separation and detection of nine hydroxylated polychlorinated biphenyls in whole blood and urine samples using ultra high performance liquid chromatography coupled with electrospray negative ionization tandem mass spectrometry. Clean‐up procedures involved a filtration step, and optimization involved a pretreatment step consisting of a simple liquid–liquid extraction using hydrated silica‐gel chromatography (5%). Nine hydroxylated polychlorinated biphenyls were separated on an ultra high performance liquid chromatography HSS T3 column using a gradient elution program of 2 mmol ammonium formate aqueous solution (A) and methanol (B). Recovery ranged from 84.0 to 105.4% for the nine different hydroxylated polychlorinated biphenyls in urine with three spiked levels of 0.1, 1, and 2 ng and from 73.5 to 98.6% for the blood with spiked levels of 0.2, 1, and 2 ng. The relative standard deviations were <8.7% (n = 6), and the limits of detection in urine and whole blood for the nine hydroxylated polychlorinated biphenyls were in the range of 1.5–4 and 20–100 pg/g, respectively. This analytical method may enable the simultaneous detection of various hydroxylated polychlorinated biphenyls from complex tissue matrices.