41Ca ultratrace determination with isotopic selectivity > 10(12) by diode-laser-based RIMS

41Ca ultratrace determination by diode-laser-based resonance ionization mass spectrometry with extremely high isotopic selectivity is presented. Application to environmental dosimetry of nuclear reactor components, to cosmochemical investigations of production cross sections, and biomedical isotope-tracer studies of human calcium kinetics are discussed. Future investigations are possible use in 41Ca-radiodating. Depending on the application, 41Ca isotopic abundances in the range of 10(-9) to 10(-15) relative to the dominant stable isotope 40Ca must be determined. Either double- or triple-resonance optical excitation with narrow-band extended cavity diode lasers and subsequent non-resonant photoionization of calcium in a collimated atomic beam were used. The resulting photoions are detected with a quadrupole mass spectrometer optimized for background reduction and neighboring mass suppression. Applying the full triple-resonance scheme provides a selectivity of approximately 5 x 10(12) in the suppression of neighboring isotopes and > 10(8) for isobars, together with an overall detection efficiency of approximately 5 x 10(-5). Measurements on a variety of sample types are discussed; the accuracy and reproducibility of the resulting 41Ca/40Ca isotope ratios was better than 5%.     

Diode-laser-based resonance ionization mass spectrometry of the long-lived radionuclide 41Ca with <10-12 sensitivity

There are a number of applications requiring measurement of the long-lived radionuclide ⁴¹ Ca at isotopic abundance, relative to ⁴⁰ Ca, in the range of 10^-8 to 10^-16 . The long lifetime and electron-capture decay mode make radio-analytical measurements impractical and conventional mass spectrometric methods can not overcome isobaric interferences such as ⁴¹ K⁺ or ⁴⁰ CaH⁺ at these levels. We approach this problem by combining laser-based resonance ionization spectroscopy with mass spectrometry. Using high-resolution single-mode lasers for resonant excitation and an intense non-resonant laser for ionization of the selectively created excited-state atoms, it is possible to essentially eliminate interference from isobars and to obtain additional optical isotopic selectivity, which can be combined with that of the mass spectrometer. Single-, double-, and triple-resonance excitation schemes have been investigated experimentally and theoretically, and it is found that performance with respect to both selectivity and sensitivity increases dramatically with each additional resonance step. Thus far, triple-resonance measurements have demonstrated minimum detectable isotopic abundance of 2.5·10^-13 with detection limits of ~2·10⁵ atoms.     

Determination of isotopic composition and concentration of uranium,plutonium and neodymium by mass-spectrometric isotope dilution in the irradiated fuel of the Czechoslovak atomic power station A-1

Determination of the isotopic composition and concentration of uranium, plutonium and neodymium by mass-spectrometric isotope dilution is described. Isotopes²³³U,²⁴²Pu and¹⁵⁰Nd were used as spikes. Isotopic composition was measured with a Varian-TH 5 mass spectrometer. Optimum amounts loaded onto the filament were 2–5 μg U, ∼0.1 μg Pu and <0.1 μg Nd. The accuracy and reproducibility of the isotopic ratio and concentration measurements were evaluated.     

Recent developments in and applications of resonance ionization mass spectrometry

Resonance Ionization Mass Spectrometry (RIMS) has nowadays reached the status of a routine method for sensitive and selective ultratrace determination of long-lived radioactive isotopes in environmental, biomedical and technical samples. It provides high isobaric suppression, high to ultra-high isotopic selectivity and good overall efficiency. Experimental detection limits are as low as 10⁶ atoms per sample and permit the fast and sensitive determination of ultratrace amounts of radiotoxic contaminations. Experimental arrangements for the detection of different radiotoxic isotopes, e.g. ^236–244Pu, ^89,90Sr and ⁹⁹Tc in environmental samples are described, and the application of RIMS to the ultrarare long-lived radioisotope ⁴¹Ca for cosmochemical, radiodating and medical purposes are presented. Received: 17 December 1998 / Revised: 11 February 1999/Accepted: 18 February 1999     

Recent developments in and applications of resonance ionization mass spectrometry

Resonance Ionization Mass Spectrometry (RIMS) has nowadays reached the status of a routine method for sensitive and selective ultratrace determination of long-lived radioactive isotopes in environmental, biomedical and technical samples. It provides high isobaric suppression, high to ultra-high isotopic selectivity and good overall efficiency. Experimental detection limits are as low as 10⁶ atoms per sample and permit the fast and sensitive determination of ultratrace amounts of radiotoxic contaminations. Experimental arrangements for the detection of different radiotoxic isotopes, e.g. ^236–244Pu, ^89,90Sr and ⁹⁹Tc in environmental samples are described, and the application of RIMS to the ultrarare long-lived radioisotope ⁴¹Ca for cosmochemical, radiodating and medical purposes are presented. Received: 17 December 1998 / Revised: 11 February 1999/Accepted: 18 February 1999     

Determination of neodymium, holmium and erbium in mixed rare earths by norfloxacin

Norfloxacin (NFX) is proposed as reagent for the derivative spectrophotometric determination of neodymium, holmium and erbium in mixed rare earths. The absorption spectra of 4f electron transitions of the systems of neodymium, holmium and erbium complexes with norfloxacin in presence of cetylpyridinium chloride were studied by normal and derivative spectra. The absorption bands found normally at 575 nm for neodymium, 450 nm for holmium and 523 nm for erbium were enhanced markedly. Using the second derivative spectrum, Beer’s Law is obeyed from 5.0 × 10^–5∼ 2.5 × 10^–4 mol dm^–3 for neodymium, holmium and erbium. The relative standard deviations are 1.0, 1.4 and 1.1% for 6.9 × 10^–5 mol dm^–3 of neodymium, 6.1 × 10^–5 mol dm^–3 of holmium and 6.0 × 10^–5 mol dm^–3 of erbium, respectively. A method for the direct determination of neodymium, holmium and erbium in mixtures of rare earth elements with good accuracy and selectivity, is described. Received: 18 December 1997 / Revised: 23 February 1998 / Accepted: 26 February 1998     

Determination of neodymium, holmium and erbium in mixed rare earths by norfloxacin

Norfloxacin (NFX) is proposed as reagent for the derivative spectrophotometric determination of neodymium, holmium and erbium in mixed rare earths. The absorption spectra of 4f electron transitions of the systems of neodymium, holmium and erbium complexes with norfloxacin in presence of cetylpyridinium chloride were studied by normal and derivative spectra. The absorption bands found normally at 575 nm for neodymium, 450 nm for holmium and 523 nm for erbium were enhanced markedly. Using the second derivative spectrum, Beer’s Law is obeyed from 5.0 × 10^–5∼ 2.5 × 10^–4 mol dm^–3 for neodymium, holmium and erbium. The relative standard deviations are 1.0, 1.4 and 1.1% for 6.9 × 10^–5 mol dm^–3 of neodymium, 6.1 × 10^–5 mol dm^–3 of holmium and 6.0 × 10^–5 mol dm^–3 of erbium, respectively. A method for the direct determination of neodymium, holmium and erbium in mixtures of rare earth elements with good accuracy and selectivity, is described. Received: 18 December 1997 / Revised: 23 February 1998 / Accepted: 26 February 1998     

Labeling the human skeleton with 41Ca to assess changes in bone calcium metabolism

Bone research is limited by the methods available for detecting changes in bone metabolism. While dual X-ray absorptiometry is rather insensitive, biochemical markers are subject to significant intra-individual variation. In the study presented here, we evaluated the isotopic labeling of bone using ⁴¹Ca, a long-lived radiotracer, as an alternative approach. After successful labeling of the skeleton, changes in the systematics of urinary ⁴¹Ca excretion are expected to directly reflect changes in bone Ca metabolism. A minute amount of ⁴¹Ca (100 nCi) was administered orally to 22 postmenopausal women. Kinetics of tracer excretion were assessed by monitoring changes in urinary ⁴¹Ca/⁴⁰Ca isotope ratios up to 700 days post-dosing using accelerator mass spectrometry and resonance ionization mass spectrometry. Isotopic labeling of the skeleton was evaluated by two different approaches: (i) urinary ⁴¹Ca data were fitted to an established function consisting of an exponential term and a power law term for each individual; (ii) ⁴¹Ca data were analyzed by population pharmacokinetic (NONMEM) analysis to identify a compartmental model that describes urinary ⁴¹Ca tracer kinetics. A linear three-compartment model with a central compartment and two sequential peripheral compartments was found to best fit the ⁴¹Ca data. Fits based on the use of the combined exponential/power law function describing urinary tracer excretion showed substantially higher deviations between predicted and measured values than fits based on the compartmental modeling approach. By establishing the urinary ⁴¹Ca excretion pattern using data points up to day 500 and extrapolating these curves up to day 700, it was found that the calculated ⁴¹Ca/⁴⁰Ca isotope ratios in urine were significantly lower than the observed ⁴¹Ca/⁴⁰Ca isotope ratios for both techniques. Compartmental analysis can overcome this limitation. By identifying relative changes in transfer rates between compartments in response to an intervention, inaccuracies in the underlying model cancel out. Changes in tracer distribution between compartments were modeled based on identified kinetic parameters. While changes in bone formation and resorption can, in principle, be assessed by monitoring urinary ⁴¹Ca excretion over the first few weeks post-dosing, assessment of an intervention effect is more reliable ∼150 days post-dosing when excreted tracer originates mainly from bone.     

Potentiometric Determination of Menadione (Vitamin K3)

 The construction and electrochemical response characteristics of poly(vinyl) chloride matrix membrane sensors for menadione (vitamin K₃) are described. Membranes incorporating the ion association complexes of menadione anion with bathophenanthroline nickel(II) and iron(II) as electroactive materials show linear response for menadione over the range 10⁻¹–10⁻⁵ M with anionic slopes of 58.2–51.4 mV per concentration decade. Both sensors exhibit fast response time (20–30 s), low detection limit (2 × 10⁻⁵ M), good stability (4–6 weeks) and selectivity coefficient (10⁻¹–10⁻³). Direct potentiometric determination of menadione under static and hydrodynamic mode of operations shows average accuracies of 98.8 and 98.5% with relative standard deviations of 0.6% and 1.3%, respectively. Application of the method for the determination of menadione in human plasma gives favourable results compared with those obtained by the standard spectrophotometric method. Received February 26, 2001. Revision October 1, 2001.     

Species-specific isotope-ratio measurements of volatile tin and antimony compounds using capillary GC–ICP–time-of-flight MS

The analytical performance of an axial inductively-coupled-plasma time-of-flight mass spectrometer (ICP–TOFMS) as a detector for fast transient chromatographic signals resulting from the coupling to capillary gas chromatography (CGC) was investigated. A cryotrapping GC–ICP–TOFMS method for the determination of volatile metal(loid) compounds (VOMs) in gases was used and the suitability of the TOF mass analyzer for multi-elemental speciation analysis and multi-isotope ratio determinations was studied in terms of accuracy and precision. Isotope ratios ¹¹⁸Sn/¹²⁰Sn and ¹²¹Sb/¹²³Sb have been determined in in-house gas standard atmospheres in Tedlar bags at two different levels (100 pg and 1 ng) for different elemental species (SnH₄, MeSnH₃, Me₂SnH₂, Me₃SnH, BuSnH₃, SbH₃, and MeSbH₂). A limitation arising from counting statistics in both detection modes could be shown. A solution containing rhodium (10 ng mL^–1) and cadmium (40 ng mL^–1) was introduced simultaneously to the GC outlet. Rhodium acts as a continuous internal standard and Cd is used for mass-bias correction (by measuring the ¹¹¹Cd/¹¹³Cd ratio). The detection system in both pulse counting and analog mode was examined. The best attainable precision was established for Me₂SnH₂ (analog mode, 12 replicates, 1 ng, RSD 0.34%, accuracy 0.31%) whereas most other species ranged between 0.4 and 0.5% RSD if higher concentrations were used. The limitations of the pulse counting system are clearly seen, with peak heights of more than 2000 counts reaching saturation (for an integration time of 100 ms), which reduces the accuracy of isotope ratio determinations. A dozen VOM could be detected in an aged landfill gas sample; several unidentified Sn compounds were present. Although their isotope ratios are within the confidence value of the standards, it is not yet clear if the acquired precision is good enough to identify isotopic fractionation of metal(loid)s through biovolatilization processes. With the precision achieved, the combination of cryotrapping GC and ICP–TOFMS is a powerful tool for monitoring volatile multi-element species in multi-tracer experiments and isotope dilution methodology. Received: 23 November 2000 / Revised: 19 February 2001 / Accepted: 24 February 2001     

ICP–MS with hexapole collision cell for isotope ratio measurements of Ca, Fe, and Se

To avoid mass interferences on analyte ions caused by argon ions and argon molecular ions via reactions with collision gases, an rf hexapole filled with helium and hydrogen has been used in inductively coupled plasma mass spectrometry (ICP–MS), and its performance has been studied. Up to tenfold improvement in sensitivity was observed for heavy elements (m > 100 u), because of better ion transmission through the hexapole ion guide. A reduction of argon ions Ar⁺ and the molecular ions of argon ArX⁺ (X = O, Ar) by up to three orders of magnitude was achieved in a hexapole collision cell of an ICP–MS (“Platform ICP”, Micromass, Manchester, UK) as a result of gas-phase reactions with hydrogen when the hexapole bias (HB) was set to 0 V; at an HB of 1.6 V argon, and argon-based ions of masses 40 u, 56 u, and 80 u, were reduced by approximately four, two, and five orders of magnitude, respectively. The signal-to-noise ratio ⁸⁰Se/ ⁴⁰Ar₂ ⁺ was improved by more than five orders of magnitude under optimized experimental conditions. Dependence of mass discrimination on collision-cell properties was studied in the mass range 10 u (boron) to 238 u (uranium). Isotopic analysis of the elements affected by mass-spectrometric interference, Ca, Fe, and Se, was performed using a Meinhard nebulizer and an ultrasonic nebulizer (USN). The measured isotope ratios were comparable with tabulated values from IUPAC. Precision of 0.26%, 0.19%, and 0.12%, respectively, and accuracy of 0.13% 0.25%, and 0.92%, respectively, was achieved for isotope ratios ⁴⁴Ca/ ⁴⁰Ca and ⁵⁶Fe/⁵⁷Fe in 10 μg L^–1 solution nebulized by means of a USN and for ⁷⁸Se/⁸⁰Se in 100 μg L^–1 solution nebulized by means of a Meinhard nebulizer. Received: 15 December 2000 / Revised: 26 March 2001 / Accepted: 27 March 2001     

Isotopic and ultratrace analysis of uranium by double-focusing sector field ICP mass spectrometry

An analytical method for the ultratrace and isotopic analysis of uranium in radioactive waste samples using a double-focusing sector field ICP mass spectrometer is described. In high-purity water a detection limit for uranium in the lowest fg/mL range has been achieved. Under optimum experimental conditions (²³⁵U/²³⁸U ≈ 1), the precision in ²³⁵U/²³⁸U isotopic ratio determinations has been determined as 0.07% RSD. With the isotopic standard U-020 (²³⁵U/²³⁸U = 0.0208) a precision of 0.23% RSD at the 100 pg/mL level using ultrasonic nebulization has been achieved. With ²³⁴U/²³⁸U isotopic ratios of down to 10^–5, the values obtained by double-focusing sector field ICP-MS and alpha spectrometry were in agreement. Received: 27 February 1997 / Revised: 10 Juni 1997 / Accepted: 12 June 1997     

Highly selective thiocyanate poly(vinyl chloride) membrane electrode based on a cadmium–Schiff’s base complex

A PVC membrane electrode based on a cadmium–salen (N,N′-bis-salicylidene-1,2ethylenediamine) complex as an anion carrier is described. The electrode has an anti-Hofmeister selectivity sequence with a preference for thiocyanate at pH 1.5–11.0. It has a linear response to thiocyanate from 1.0 × 10^–6 to 1.0 × 10^–1 mol L^–1 with a slope of 59.1 ± 0.2 mV per decade, and a detection limit of 7 × 10^–7 mol L^–1. This electrode has high selectivity for thiocyanate relative to many common organic and inorganic anions. The proposed sensor has a fast response time of approximately 15 s. It was applied to the determination of thiocyanate in a milk sample. Received: 1 December 2000 / Revised: 19 April 2001 / Accepted: 30 April 2001     

The determination of arsenic and selenium in standard reference materials using sector field ICP-MS in high resolution mode

Sector field ICP-MS was used to analyse As and Se in a range of standard reference materials (NIST 1643d Water, NIST 1573a Tomato Leaves, NIST 1566a Oyster Tissue, NIST 2704 Buffalo River Sediment and Bio-Rad Reference Urine Level 2). A spectral resolution of m/Δm = 7500 enabled ⁷⁵As and ⁷⁷Se to be separated from problematic ArCl interferences. Following microwave acid digestion, solid samples were typically diluted 1 + 99 prior to analysis, while the urine sample was diluted 1 + 9. The water sample was analysed undiluted and diluted 1 + 9. Despite near baseline spectral separation, ⁷⁵As and ⁷⁷Se were still found to be influenced by ArCl at high Cl concentrations, the effect being most pronounced for ⁷⁷Se. When necessary ⁸²Se was also monitored to determine the accuracy of the ⁷⁷Se results. Detection limits (LOD, based on 3σ of 10 replicates) for ⁷⁵As, ⁷⁷Se and ⁸²Se in ultra-pure water, 1% (w/w) HNO₃ and 1% (w/w) HCl were ∼ 0.1, ∼ 0.2 and ∼ 0.5 ng g^–1, respectively. Although signal intensities when using high resolution were ∼ 1% of that found when using low resolution mode (m/Δm = 300), measured As concentrations and certified values were found to agree to within ± 11% for all samples analysed. The concentration of Se in NIST 1566a Oyster Tissue, NIST 2704 Buffalo River Sediment and Bio-Rad Reference Urine were found to be in agreement with certified values to within ± 15– 20%, as measured by ⁷⁷Se. However, closer agreement (± 5%) was found when these samples were analysed using ⁸²Se. The Se concentration in NIST 1643d Water was found to agree to within ± 5% of the certified value (depending on dilution factor). Due to the low concentration of Se in NIST 1573a Tomato Leaves, quantitation was not possible (below LOQ, 10σ). As a consequence of the lower ion transmission when using resolution 7500, analytical precisions were found to be elevated over that normally observed using low resolution mode, typically ± 5–20% (depending on analyte concentration and isotopic abundance). Received: 28 December 1998 / Accepted: 9 February 1999     

Application of neutron activation analysis to the measurement of isotope abundance shifts in calcium and potassium

A simple method for the measurement by neutron activation analysis of the isotopic abundance shifts of⁴⁴Ca and⁴¹K in compounds of low volatility is described. Extraction and measurement procedures for the radioactive argon isotopes (³⁷Ar,³⁹Ar and⁴¹Ar produced by (n, α) and (n, p) reactions are also given. The results obtained demonstrate that the accuracy for the measurement of δ⁴⁴Ca is better than by the mass spectrometric method; in the case of δ⁴¹K measurement the accuracy is the same as that obtained with the mass spectrometer. Interfering reactions which yield other rare gases, and their relative contribution to the error in the measurement of δ values are also discussed.     

Concentration of polycyclic aromatic hydrocarbons by chemically modified silver nanoparticles

The ability of silver nanoparticles stabilized by cetyltrimethylammonium bromide (CTAB) to concentrate polycyclic aromatic hydrocarbons (PAHs) from aqueous solutions was shown. It was found that fixed PAH molecules are capable of acting as electronic energy donors and of generating sensibilized fluorescence of silver nanoparticles. It was shown by spectral-luminescent investigations of dilute PAH solutions (5 × 10⁻¹⁰−1 × 10⁻⁶ g/ml) in the presence of silver nanoparticles (∼0.7 vol %) that the concentration of PAH molecules from solutions occurs due to its sorption on hydrocarbon CTAB radicals in close contact to the surface of metallic silver. On the basis of the spectral data, the sorption isotherms were obtained and the values of extraction degree and partition coefficients for naphthalene, phenanthrene, anthracene, chrysene, pyrene, and 3,4-benzopyrene were calculated. It was found that the degree of extraction values of the investigated PAHs fall within the range of 73–98%, the partition coefficients (logD) ∼ 6, and the concentration coefficients ∼10⁵.     

Capillary electrophoresis–electrospray mass spectrometry and HR–ICP–MS for the detection and quantification of 10B-boronophenylalanine (10B–BPA) used in boron neutron capture therapy

Boron neutron capture therapy (BNCT) is a bimodal radiotherapeutic treatment based on the irradiation of neoplastic tissues with neutrons after the tissues have selectively accumulated molecules loaded with nuclides with large neutron capture cross-sections (such boron-10). Boron-10 carriers have been tested to a limited extent, and clinical trials have been conducted on sulfhydryl borane (¹⁰B-BSH) and boronophenylalanine (¹⁰B-BPA). However, precise and accurate measurements of boron-10 concentrations (0.1–100 μg/g) in specimens and samples of limited size (μg scale) are needed in order to be able to biologically characterise new compounds in predictive tissue dosimetry, toxicology and pharmacology studies as well as in clinical investigations. A new approach based on fast separation and detection of ¹⁰B-BPA performed by coupling capillary electrophoresis to electrospray mass spectrometry is reported. This method allows the quantitative analysis and characterisation of ¹⁰B-BPA in a short time with a high separation efficiency. Detection limits of 3 μM for ¹⁰B-BPA and 30 ng/mL for ¹⁰B were obtained with CE–ESI–MS. A quantification limit of 10 μM for ¹⁰B-BPA (100 ng/mL for ¹⁰B) was attained. The total boron-10 concentration was determined by high-resolution inductively coupled mass spectrometry in order to validate the method. Boron-10 isotope measurements were carried out by HR–ICP–MS at medium resolution (R=4000) due to the presence of an isobaric interference at mass 10. Good agreement was obtained between the values from CE–ESI–MS and those from HR–ICP–MS. The method has been successfully used to determine the ¹⁰B-BPA in two lines of cultured cells.     

Determining the isotopic compositions of uranium and fission products in radioactive environmental microsamples using laser ablation ICP–MS with multiple ion counters

This paper presents the application of a multicollector inductively coupled plasma mass spectrometer (MC–ICP–MS)—a Nu Plasma HR—equipped with three ion-counting multipliers and coupled to a laser ablation system (LA) for the rapid and sensitive determination of the ²³⁵U/²³⁸U, ²³⁶U/²³⁸U, ¹⁴⁵Nd/¹⁴³Nd, ¹⁴⁶Nd/¹⁴³Nd, ¹⁰¹Ru/(⁹⁹Ru+⁹⁹Tc) and ¹⁰²Ru/(⁹⁹Ru+⁹⁹Tc) isotope ratios in microsamples collected in the vicinity of Chernobyl. Microsamples with dimensions ranging from a hundred μm to about 1 mm and with surface alpha activities of 3–38 mBq were first identified using nuclear track radiography. U, Nd and Ru isotope systems were then measured sequentially for the same microsample by LA–MC–ICP–MS. The application of a zoom ion optic for aligning the ion beams into the ion counters allows fast switching between different isotope systems, which enables all of the abovementioned isotope ratios to be measured for the same microsample within a total analysis time of 15–20 min (excluding MC–ICP–MS optimization and calibration). The ¹⁰¹Ru/(⁹⁹Ru+⁹⁹Tc) and ¹⁰²Ru/(⁹⁹Ru+⁹⁹Tc) isotope ratios were measured for four microsamples and were found to be significantly lower than the natural ratios, indicating that the microsamples were contaminated with the corresponding fission products (Ru and Tc). A slight depletion in ¹⁴⁶Nd of about 3–5% was observed in the contaminated samples, but the Nd isotopic ratios measured in the contaminated samples coincided with natural isotopic composition within the measurement uncertainty, as most of the Nd in the analyzed samples originates from the natural soil load of this element. The ²³⁵U/²³⁸U and ²³⁶U/²³⁸U isotope ratios were the most sensitive indicators of irradiated uranium. The present work yielded a significant variation in uranium isotope ratios in microsamples, in contrast with previously published results from the bulk analysis of contaminated samples originating from the vicinity of Chernobyl. Thus, the ²³⁵U/²³⁸U ratios measured in ten microsamples varied in the range from 0.0073 (corresponding to the natural uranium isotopic composition) to 0.023 (corresponding to initial ²³⁵U enrichment in reactor fuel). An inverse correlation was observed between the ²³⁶U/²³⁸U and ²³⁵U/²³⁸U isotope ratios, except in the case of one sample with natural uranium. The heterogeneity of the uranium isotope composition is attributed to the different burn-up grades of uranium in the fuel rods from which the microsamples originated. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Ultratrace analysis of calcium with high isotopic selectivity by diodelaser resonance ionisation mass spectrometry

A resonance ionisation mass spectrometer for the ultratrace determination of calcium isotopes is presented. It achieves high overall efficiency, ultra-high isotopic abundance sensitivity of more than 10¹⁰ and complete suppression of isobars. The system can be used for isotope ratio studies on stable and long-lived trace isotopes with the final goal of radiodating via ⁴¹Ca-determination. For the different applications optical one-, two- or three-step resonance excitation and subsequent ionisation is applied using simple and inexpensive diodelasers. Additional mass analysis is accomplished in a commercial quadrupole mass spectrometer. The experimental set-up and first results on synthetical and meteorite samples are described.