易拉罐在轴-侧-扭-内压联合作用下的屈曲地貌

柱壳结构广泛应用于各个领域, 但由于其对初始缺陷较为敏感, 容易发生灾难性的屈曲失稳. 本文利用非线性有限元分析程序ABAQUS研究了柱壳屈曲问题, 并应用到了易拉罐的屈曲分析. 首先采用数值模拟的方法验证了Virot等学者的易拉罐屈曲试验结果, 然后为了获得屈曲的一些普适结果, 进一步考察了柱壳的屈曲表现. 对柱壳结构在不同载荷组合、不同几何参数作用下进行了细致分析. 为了讨论的直观, 本文绘制了柱壳结构在受到侧压-轴压载荷作用下外力-屈曲载荷-位移三维屈曲地貌图(称为landscape). 结果表明: 在侧压-轴压-扭转载荷作用下, 试件力-位移曲线出现了"cliff"(断崖)现象; 扭转载荷的施加不利于试件整体稳定性, 并造成了试件对初始缺陷的敏感性; 对于受到轴压-扭转载荷作用的试件, 本文定义承载力为零的平面为"sea level"(海平面)来区分试件破坏模式; 通过对不同边界条件的试件进行分析, 发现试件两端固定可以有效地增加结构的承载能力, 提高稳定性. 对柱壳结构内部充气可以大幅度提升结构的承载能力和稳定性, 减小对初始缺陷的敏感度.      

Influence of general imperfections in axially loaded cylindrical shells

The buckling of an axially loaded cylindrical shell is considered when imperfection components corresponding to all of the classical buckling modes are taken into consideration. The analysis represents an extension of Koiter's axisymmetric solution and in the asymptotic sense due to Koiter the imperfections considered are as general as possible. The results obtained reveal many interesting aspects of shell buckling which arize for various imperfection forms. The buckling behaviour which results is associated with both bifurcation and limit point critical states.     

The thermal effect on axially compressed buckling of a double-walled carbon nanotube

The thermal effect on axially compressed buckling of a double-walled carbon nanotube is studied in this paper. The effects of temperature change, surrounding elastic medium and van der Waals forces between the inner and outer nanotubes are taken into account. Using continuum mechanics, an elastic double-shell model with thermal effect is presented for axially compressed buckling of a double-walled carbon nanotube embedded in an elastic matrix under thermal environment. Based on the model, an explicit formula for the critical axial stress is derived in terms of the buckling modes of the shell and the parameters that indicate the effects of temperature change, surrounding elastic medium and the van der Waals forces. Based on that, some simplified analysis is carried out to estimate the critical axial stress for axially compressed buckling of the double-walled carbon nanotube. Numerical results for the general case are obtained for the thermal effect on axially compressed buckling of a double-walled carbon nanotube. It is shown that the axial buckling load of double-walled carbon nanotube under thermal loads is dependent on the wave number of axially buckling modes. And a conclusion is drawn that at low and room temperature the critical axial stress for infinitesimal buckling of a double-walled carbon nanotube increase as the value of temperature change increases, while at high temperature the critical axial stress for infinitesimal buckling of a double-walled carbon nanotube decrease as the value of temperature change increases.     

Torsional,flexural, and torsional-flexural buckling modes of a cylindrical shell under combined loading

Stability problems for cylindrical shells under various loading modes were considered in numerous papers. A detailed analysis of such problems can be found, e.g., in the monograph [1]. We refer to the solutions presented in this monograph as classical.For long cylindrical shells in axial compression, one of the buckling modes is the purely beam flexural mode similar to the classical buckling mode of a straight rod. It is well known that it can be studied by using the nonlinear or linearized equations of the membrane theory of shells. In [2], it was shown that, on the basis of such equations constructed starting from the noncontradictory version of geometrically nonlinear elasticity relations in the quadratic approximation [3], under the separate action of the axial compression, external pressure, and torsion, there are also previously unknown nonclassical buckling modes, most of which are shear ones.In the present paper, we show that the use of the above equations for cylindrical shells under compression and external pressure with simultaneous pure torsion or bending permits revealing the earlier unknown torsional, beam flexural, and beam torsional-flexural buckling modes, which are nonclassical, just as those found in [2]. The second of these buckling modes is realized when axially compressing forces are formed in the shell with simultaneous torsion, and the third of them is realized under compression combined with pure bending.It was found that, earlier than the classical buckling modes, the torsional buckling modes can be realized for relatively short shells with small shear rigidity in the tangent plane, while the second and third buckling modes can be realized for relatively long shells.     

Ermittlung der Beultraglasten ausgesteifter Schalen mit Hilfe von Übertragungsmatrizen

Übersicht Bei Beultraglastsberechnungen von ausgesteiften Kreiszylinderschalen unter Axialbelastung im plastischen Bereich werden das Deformationsverfahren und das Eigenwertverfahren mit Hilfe von übertragungsmatrizen verwendet, wobei die Übertragungsmatrix im Deformationsverfahren aus der nach der Finite-Element-Methode gewonnenen Steifigkeitsmatrix hergeleitet wird. Bei gleichzeitiger Berücksichtigung der Vorverformungen und der Restspannungen bzw. bei alleiniger Berücksichtigung der Restspannungen werden Rechenergebnisse von längsausgesteiften Schalen nach beiden Verfahren vorgelegt und verglichen.

---

Study of the buckling load of stiffened shells by the transfer matrix method

Summary The deformation and eigenvalue method using the transfer matrix are applied to ultimate strength analyses of axially compressed, stiffened cylindrical shells in the plastic range. The transfer matrix in the deformation method is obtained by suitable transformation of the stiffness matrix used in the finite element method, and the transfer matrix in the eigenvalue method is described by the linearized differential equation of shells. In the deformation method geometrical imperfections and residual stresses are taken into consideration, while in the eigenvalue method the former are not considered. The numerical results of stiffened shells obtained by both methods are illustrated and compared with each other.

     

Postbuckling and Imperfection Sensitivity Analysis of Axially Stiffened Cylindrical Shells with Mode Interaction

Abstract

Interaction of nearly simultaneous buckling modes in the presence of imperfections is studied. The investigation is concerned with axially stiffened cylindrical shells under axial compression. In these structures, two modes are of particular interest, namely an overall long-wave and a local shortwave buckling mode. Numerical results show that in some cases bending of the stringers in the local mode postbuckling solution plays an important role. Exclusion of this effect, as was done in a previous study by Byskov and Hutchinson, may lead to an overestimation of the carrying capacity of the shell. Furthermore, it is found that apparently reasonable approximations to the postbuckling fields associated with both the local and the overall mode, as well as with the overall mode alone, may lead to inexact values of the buckling load.     

Creep buckling of axially compressed circular cylindrical shells of a zirconium alloy: Experiment and computer simulation

Experiments were performed to study the deformation and buckling of axially compressed circular cylindrical shells of Zr2.5Nb zirconium alloy under creep conditions. Computer simulation using the MSC.Marc 2012 software was conducted by step-by-step integration of the equations of quasistatic deformation of thin shells using Norton’s law of steady creep. The results of the experiment and computer simulation show that the buckling modes are a combination of axisymmetric bulges located near one end or both ends of the shell and axisymmetric buckling modes with the formation of three or four waves in the circumferential direction. A comparison is made of the time dependences of the axial strain of the shells obtained in the experiment and by computer simulation. It is shown that for large axial compressive stresses, these dependences are in satisfactory agreement. For lower values of these stresses, the difference between the theoretical and experimental dependences is greater.     

Axial load capacity of cylindrical shells with local geometric defects

The effect of local geometric defects on the buckling load of axially compressed thin circular cylindrical shells is investigated experimentally. Defects, in the form of diamond-shaped local dimples, similar to the buckles of the Yoshimura pattern, were introduced in otherwise near perfect isotropic epoxy shells by locally heating the shell wall. The behavior of the defects under load was monitored optically using a special whole-field grid-reflection technique. The effects of variations in shell geometry and defect size are also investigated. In general, the results indicate that the effect of local diamond-shaped defects on the stability of the axially loaded cylinder is not as detrimental as that of the global initial imperfections hitherto investigated.     

圆柱壳稳定性问题的研究进展

圆柱壳是工程实际中广泛应用的结构,其主要破坏形式是屈曲失稳．作为力学领域的经典问题,圆柱壳稳定性问题的研究非常之多．其中,受均匀轴向压力的圆柱壳由于临界屈曲载荷的理论预测值与早期试验结果之间的巨大差异,更是推动了壳体稳定性理论的不断发展．本文简要回顾了壳体稳定性理论的发展和分类,并对轴压圆柱壳体试验结果分散且远低于理论预测值的原因及含缺陷圆柱壳体的稳定性研究方法进行了总结,然后综述了地下空间顶管、储油罐、加筋圆柱壳及脱层圆柱壳等实际工程中广泛应用的圆柱壳结构稳定性研究的现状和趋势,最后展望了将来对工程应用中圆柱壳结构的稳定性研究的难点和方向．     

On modified displacement version of the non-linear theory of thin shells

We discuss the non-linear theory of thin shells expressed in terms of displacements of the shell reference surface as the only independent field variables. The formulation is based on the principle of virtual work postulated for the reference surface. In our approach: (1) the vector equilibrium equations are represented through components in the deformed contravariant surface base, and using the compatibility conditions the resulting tangential equilibrium equations are additionally simplified, (2) at the shell boundary the new scalar function of displacement derivatives is defined and new sets of four work-conjugate static and geometric boundary conditions are derived, as well as (3) for prescribed shell geometry all non-linear shell relations are generated automatically by two packages set up in Mathematica. The displacement boundary value problem and the associated homogeneous shell buckling problem are generated exactly without using any additional approximations following from errors of the constitutive equations. Both problems are extremely complex and available only in the computer memory. Such an approach allows us to account also for those a few supposedly small terms which may be critical for finding the correct buckling load of shells sensitive to imperfections. This approach is used in the accompanying paper by Opoka and Pietraszkiewicz [Opoka, S., Pietraszkiewicz, W., 2009. On refined analysis of bifurcation buckling for the axially compressed circular cylinder. International Journal of Solids and Structures, 46, 3111–3123.] to perform the refined numerical analysis of bifurcation buckling for the axially compressed circular cylinder.     

To the problem of stability of a cylindrical shell under axial compression

The classical problem of stability of a thin elastic cylindrical shell loaded by axial compressions forces is considered. The axially symmetric and non-axisymmetric buckling modes of isotropic and orthotropic shells are studied. In contrast to the traditional approach, the well-known expressions for the critical load are obtained by analyzing the equations for the shell behavior and are independent of the boundary conditions.     

Buckling of elastic-plastic cylindrical panel under axial compression

The buckling behaviour is investigated for an axially compressed elastic-plastic cylindrical panel of the type occurring in stiffened shells. The bifurcation stress is determined analytically and an asymptotically exact expansion is obtained for the initial post-bifurcation behaviour in the plastic range. For panels with small initial imperfections the behaviour is analysed asymptotically on the basis of the hypoelastic theory that results from neglecting the effect of elastic unloading. The imperfection-sensitivity of an elastic-plastic panel is also computed numerically by a linear incremental method, and the results are compared with the results of the asymptotic analysis. For a low hardening material the panel is found to be imperfection-sensitive in the whole range of curvatures considered, whereas for a high hardening material the panel is only imperfection-sensitive if the curvature exceeds a certain value.     

F E M analysis of delamination buckling in composite plates and shells

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｐｒｏｂｌｅｍｏｆｄｅｌａｍｉｎａｔｉｏｎｂｕｃｋｌｉｎｇｏｆｃｏｍｐｏｓｉｔｅｌａｍｉｎａｔｅｓｈａｓｇｅｎｅｒａｔｅｄｓｉｇｎｉｆｉｃａｎｔｒｅｓｅａｒｃｈｉｎｔｅｒｅｓｔｓａｎｄｈａｓｂｅｅｎｔｈｅｓｕｂｊｅｃｔｏｆｍａｎｙｔｈｅｏｒｅｔｉｃａｌｉｎｖｅｓｔｉｇａｔｉｏｎｓｉｎｔｈｉｓｄｅｃａｄｅ.Ａｆｉｎｉｔｅｅｌｅｍｅｎｔｍｏｄｅｌ[1]ｗａｓｐｒｅｓｅｎｔｅｄｔｏｓｏｌｖｅｔｈｅｐｏｓｔ＿ｂｕｃｋｌｉｎｇｐｒｏｂｌｅｍｏｆｃｏｍｐｏｓｉｔｅｐｌａｔｅｓｗｉｔ…     

On the Buckling of Axially Compressed Thin Cylindrical Shells

ABSTRACT

A simple general method for the evaluation of the effect of shape imperfections on the buckling of thin shells is briefly presented. This method is applied to the axially compressed thin cylindrical shell resulting in an efficient numerical procedure for the computation of its buckling strength. The procedure is applicable to any sufficiently smooth imperfection pattern and has given results in good agreement with the available experimental data.     

U型波纹管及相关结构环向屈曲的有限元分析(Ⅱ）--半圆环壳的屈曲

环壳不仅是U型波纹管的一个组成部分，更是一类重要的结构，在航天、核能和海洋工程中有重要的应用，其屈曲是人们关注的问题之一，其中对半圆环壳的分析还较为少见。本文采用文[7]的有限元法（考虑了屈曲前的弯曲和屈曲时载荷的转动并按线性化特征值问题处理）计算了正Gauss曲率半圆环壳在均匀外压作用下的屈曲，将所得结果与已知的近似解进行了对比、并讨论了其中的差异。本文除了给出临界载荷和子午线的屈曲模态外，还给出了前屈曲弯曲应力分布，以便仔细了解屈曲问题。     

Axisymmetric static and dynamic buckling of hollow microspheres

Syntactic foams are particulate composites that are obtained by dispersing thin hollow inclusions in a matrix material. The wide spectrum of applications of these composites in naval and aerospace structures has fostered a multitude of theoretical, numerical, and experimental studies on the mechanical behavior of syntactic foams and their constituents. In this work, we study static and dynamic axisymmetric buckling of single hollow spherical particles modeled as non-linear thin shells. Specifically, we compare theoretical predictions obtained by using Donnell, Sanders–Koiter, and Teng–Hong non-linear shell theories. The equations of motion of the particle are obtained from Hamilton׳s principle, and the Galerkin method is used to formulate a tractable non-linear system of coupled ordinary differential equations. An iterative solution procedure based on the modified Newton–Raphson method is developed to estimate the critical static load of the microballoon, and alternative methodologies of reduced complexity are further discussed. For dynamic buckling analysis, a Newmark-type integration scheme is integrated with the modified Newton–Raphson method to evaluate the transient response of the shell. Results are specialized to glass particles, and a parametric study is conducted to investigate the effect of microballoon wall thickness on the predictions of the selected non-linear shell theories. Comparison with finite element predictions demonstrates that Sanders–Koiter theory provides accurate estimates of the static critical load for a wide set of particle wall thicknesses. On the other hand, Donnell and Teng–Hong theories should be considered valid only for very thin particles, with the latter theory generally providing better agreement with finite element findings due to its more complete kinematics. In this context, we also demonstrate that a full non-linear analysis is required when considering thicker shells, while simplified treatment can be utilized for thin particles. For dynamic buckling, we confirm the accuracy of Sanders–Koiter theory for all the considered particle thicknesses and of Teng–Hong and Donnell theories for very thin particles.     

Length dependence of critical measures in single-walled carbon nanotubes

This paper presents an investigation on the buckling behaviour of single-walled carbon nanotubes under various loading conditions (compression, bending and torsion) and unveils several aspects concerning the dependence of critical measures (axial strain, bending curvature and twisting angle) on the nanotube length. The buckling results are obtained by means of an atomistic-scale generalized beam theory (GBT) that incorporates local deformation of the nanotube cross-section by means of independent and orthogonal deformation modes. Moreover, some estimates are also obtained by means of non-linear shell finite element analyses using Abaqus code. After classifying the buckling modes of thin-walled tubes (global, local and distortional), the paper addresses the importance of the two-wave distortional mode (flattening or ovalization mode) in their structural behaviour. Then, the well known expression to determine the critical strain of compressed nanotubes, which is based on Donnell theory for shallow shells, is shown to be inadequate for moderately long tubes due to warping displacements appearing in the distortional buckling modes. After that, an in-depth study on the buckling behaviour of nanotubes under compression, bending and torsion is presented. The variation of the critical kinematic measures (axial strain, bending curvature and twisting angle) with the tube length is thoroughly investigated. Concerning this dependence, some uncertainties that exist in the specific literature are meticulously explained, a few useful expressions to determine critical measures of nanotubes are proposed and the results are compared with available data collected from several published works (most of them, obtained from molecular dynamics simulations).     

Buckling of imperfect functionally graded cylindrical shells under axial compression

Buckling behaviors of axially compressed functionally graded cylindrical shells with geometrical imperfections are investigated in this paper using Donnell shell theory and the nonlinear strain-displacement relations of large deformation. The analysis is based on the nonlinear prebuckling consistent theory. Both the prebuckling effects and the temperature-dependent material properties are taken into account. The buckling condition for imperfect functionally graded cylindrical shells is obtained by using the Galerkin method. Numerical results show various effects of imperfection, structural type, power law exponent, temperature and dimensional parameters on buckling. The present theoretical results are verified by those in literature.     

Buckling of a pre-compressed or pre-stretched membrane in shear flow

Membranes enclosing capsules and biological cells undergo periodic compression and stretching due to an imparted hydrodynamic traction as they rotate in a shear flow. Compression may cause transient or permanent buckling manifested by the onset of wrinkled shapes. To study the effect of pre-compression and pre-stretching on the critical conditions for buckling, the response of an elastic circular plate flush mounted on a plane wall and deforming under the action of a uniform tangential load due to an over-passing simple shear flow is considered. Working under the auspices of the theory of elastic instability of plates governed by the linear von Kármán equation, an eigenvalue problem is formulated resulting in a fourth-order partial differential equation with position-dependent coefficients parametrized by the Poisson ratio. Solutions are computed by applying Fourier series expansions to derive an infinite system of coupled ordinary differential equations, and then implementing orthogonal collocation. The solution space is illustrated, critical values for buckling are identified, the associated eigenfunctions representing possible modes of deformation are displayed, and the effect of the Poisson ratio is discussed.     

On refined analysis of bifurcation buckling for the axially compressed circular cylinder

We present extensive numerical results of bifurcation buckling analysis of the axially compressed circular cylinder. The analysis is based on the modified displacement version of the non-linear theory of thin elastic shells developed by Opoka and Pietraszkiewicz [Opoka, S., Pietraszkiewicz, W., 2009. On modified displacement version of the non-linear theory of thin shells. International Journal of Solids and Structures, 46, 3103–3110.]. To solve the buckling problem we apply the separation of variables and expansion of all fields into Fourier series in circumferential direction, with subsequent accurate calculations of eigenvalues of determinants of corresponding 8 × 8 complicated matrices. The numerical analysis of the buckling load is performed for the cylinders with length-to-diameter ratio in the range (0.05, 60), with eight sets of incremental work-conjugate boundary conditions analogous to those used in the literature and partly summarized in the book by Yamaki [Yamaki, N., 1984. Elastic Stability of Circular Cylindrical Shells. Elsevier, Amsterdam], and additionally with six sets of boundary conditions not discussed in the literature yet. The results allow us to formulate several important conclusions, such as: (a) omission in the non-linear BVP small terms of the order of error introduced by the error of constitutive equations leads to overestimated buckling loads for long cylinders with clamped boundaries; (b) for some relaxed boundary conditions the buckling load decreases for short cylinders with decrease of the cylinder length; (c) the results for additional six sets of boundary conditions reveal existence of several new cases, in which by relaxing geometric boundary conditions the buckling load falls down to about one half of the classical value in a wide range of the cylinder length-to-diameter ratios.