Kinetic modeling of promotion and inhibition of temperature on photocatalytic degradation of benzene vapor

This study investigated the effects of temperature, humidity, and benzene concentration on the photocatalytic oxidation of benzene vapor over titanium dioxide. An annular packed-bed photocatalytic reactor was employed to determine the intrinsic oxidation rates for the photocatalysis of benzene. Degussa P-25 TiO₂ was used as the photocatalyst and a 15 W near-UV lamp (350 nm) was used as the light source. The experiments were conducted at influent benzene concentrations of 250–450 ppmv, water vapor concentrations of 13,500–27,500 ppmv, and reaction temperatures ranging from 100 to 200 °C. Benzene oxidation rates increased with temperature below 160–180 °C, but decreased with temperature above 160–180 °C. Raising the reaction temperature increased the chemical reaction rates but reduced the reactant adsorption rate on TiO₂ surfaces. The overall reaction rate increased with temperature, indicating that the reduction of reactant adsorption rate did not affect the overall reaction, and thus the chemical reaction was the rate-limiting step. As the chemical reaction rate gradually exceeds the reactant adsorption rate with temperature, the rate-limiting step was shifted from the chemical reaction to the reactant adsorption. Additionally, the competitive adsorption between benzene and water for the active sites on TiO₂ resulted in the promotion and inhibition of reaction rate by humidity. This study developed a modified bimolecular Langmuir–Hinshelwood kinetic model to simulate the temperature and humidity related promotion and inhibition of the photocatalysis of benzene. The correlation developed here was used as a basis for determining the apparent activation energy of 0.76 kcal/mol and adsorption enthalpies of benzene and water of −20.1 and −13.7 kcal/mol.     

Catalytic air oxidation of ambient temperature hydrocarbons

Catalytic air oxidation of the aliphatic hydrocarbons n-decane, hexanes, gasoline and diesel fuel was conducted at ambient temperature with novel iron catalysts. The concentration of n-decane in water was reduced from 1.42 g in 100 ml to 0.07 g in 100 ml in 5 h at room temperature forming carbon monoxide and water by means of intermediate aldehydes. Results of FT–IR and GC–MS analyses demonstrated formation of aldehydes and unsaturated alcohols. Carbon monoxide was detected on catalyst residues and in the vapor phase. The indicated catalytic reaction mechanisms are discussed.     

Preparation and characterization of activated carbon from date stones by physical activation with steam

Activated carbons are produced from wastes of Algerian date stones by pyrolysis and physical activation in the presence of water vapor into a heated fixed-bed reactor. The effect of pyrolysis temperature and activation hold time on textural and chemical surface properties of raw date stones and carbon materials produced are studied. As expected, the percentage yield decreases with increase of activation temperature and hold time. The characterization of carbon materials is performed by scanning electron microscopy (SEM). X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and nitrogen adsorption (BET). Results show the presence of cellulose and hemicellulose in the raw material, and the predominance of carbon and graphite after pyrolysis. Different oxygen-containing functional groups are found in the raw material while aromatic structures are developed after pyrolysis and activation. The best specific surface area (635 m² g⁻¹) and microporous volume (0.716 cm³ g⁻¹) are obtained when the date stones are grinded, pyrolysed at 700 °C under a 100 cm³ min⁻¹ nitrogen flow and then activated under water vapor at 700 °C for 6 h.     

Synthesis, water stability and proton conductivity of novel sulfonated polyimides from 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid

A novel sulfonated diamine monomer, 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid (BAPBDS) with the high basisity and flexible structure was synthesized by direct sulfonation of 4,4′-bis(4-aminophenoxy)biphenyl (BAPB). Sulfonated polyimides (SPIs) were prepared from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA), BAPBDS and nonsulfonated diamines such as BAPB. The SPI membranes showed much higher water stability at high temperatures than other sulfonated diamine-based SPIs reported so far. Their water vapor sorption isotherm, water uptake (WU), density, dimensional change and proton conductivity σ were investigated. The SPIs showed rather isotropic dimensional changes with WU and the volume increases were slightly smaller than those estimated from the additivity. The SPIs with ion exchange capacities (IECs) of 1.9–2.7 meq/g displayed the similar relationship between σ and WU each other, which was different from those of Nafion 117 and also of the SPIs with the lower IECs. The former SPIs showed reasonably high σ values of 10⁻² S/cm or more even at WU of 25 g/100 g dry polymer under 70% RH at 50 °C, whereas the latter showed the similarly high σ values only in liquid water, but not in the nearly saturated water vapor.     

Sorption isotherms, sorption enthalpies, diffusion coefficients and permeabilities of water in a multilayer PEO/PAA polymer film using the quartz crystal microbalance/heat conduction calorimeter

Sorption isotherms, sorption enthalpies, and diffusion coefficients for water in an 11 μm thick PEO/PAA multi-layer film have been measured at 30, 40, and 60 °C for relative humidities between 0 and 70%. All quantities were measured on the same film using the quartz crystal microbalance/heat conduction calorimeter. Water diffusion coefficients in the film are several orders of magnitude lower than in the separate components. Sorption isotherms are of type III at 30 and 40 °C and linear at 60 °C. Water vapor permeabilities are calculated as the product of Henry's law solubility and diffusion coefficient. The permeability of the PEO/PAA multilayer film is exceedingly low compared to other polymer films used as membranes. The enthalpy of water sorption determined from the sorption isotherms using the van’t Hoff relation is 32.9 ± 0.3 kJ/mol. Calorimetric enthalpies of water sorption range from 42 to 34 kJ/mol at 30 and 40 °C over the humidity range studied. The change in motional resistance, a quantity proportion to the loss compliance of the film, has also been recorded at all three temperatures, and a common trend is an increase in loss compliance with increasing relative humidity, indicating plasticization of the film by water.     

Synthesis of industrial scale NaY zeolite membranes and ethanol permeating performance in pervaporation and vapor permeation up to 130 °C and 570 kPa

NaY zeolite tubular membranes in an industrial scale of 80 cm long were synthesized on monolayer and asymmetric porous supports. The quality of synthesized membranes were evaluated by pervaporation (PV) experiments in 80 cm long at 75 °C in a mixture of water (10 wt.%)/ethanol (90 wt.%), resulting in higher permeation fluxes of 5.1 kg m⁻² h⁻¹ in the monolayer type membrane and of 9.1–10.1 kg m⁻² h⁻¹ in the asymmetric-type membranes, respectively. The uniformity with small performance fluctuation in longitudinal direction of the membranes were observed by PV for 10–12 cm long samples at 50 °C in a mixture of methanol (10 wt.%)/MTBE (90 wt.%). The ethanol single component permeation experiments in PV and vapor permeation (VP) up to 130 °C and 570 kPa were performed to determine the relations between the ethanol flux and the ethanol pressure difference across the membrane which is represented by permeance (Π, mol m⁻² s⁻¹ Pa⁻¹) for estimate of potential of ethanol extraction through the present NaY zeolite membranes applying feasible studies. Results indicate that (1) the permeation fluxes are linearly proportional to the driving force of vapor pressure for each sample in VP and PV. The permeances through an asymmetric support type membrane were rather constant of 0.6–1.2 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ in the wide temperature range of 90–130 °C in PV and VP, indicating that the ethanol permeances have weak temperature dependency with the feed at the saturated vapor pressure.

The results of superheating VP experiments showed that ethanol permeation fluxes are increased with increasing of the degree of superheating at a given constant feed vapor pressure. The ethanol permeances are increased with increasing of temperature at a given feed vapor pressure. The superheating VP could be a feasible process in industry.     

SPECTRALLY SENSITIZED PHOTOCONDUCTIVITY OF ZINC OXIDE CRYSTALS*

Abstract— Spectral sensitization of photoconductivity was found after coating single crystals with an organic dye in a methanol solution. Similar experiments have been carried out under conditions designed to exclude the influence of solvent and adsorbed gases. The dye was deposited from vapor onto clean crystal surfaces in ultrahigh vacuum and the spectral distribution of the photoconductivity was observed without admission of air. With both methods of dyeing, the quantum yields, referred to the absorbed light, were comparable to the yield in the intrinsic region. Also the influence of a transverse electric field upon surface conductivity before and after dyeing was studied. From the ‘field effect’ it is concluded that the adsorbed dye causes a considerable increase of the density of electronic surface states near the Fermi level.     

The effect of humidity on thermal process of zinc acetate

The thermal decomposition of zinc acetate dihydrate Zn(CH₃CO₂)₂·2H₂O in some humidity-controlled atmospheres has been successfully investigated by novel thermal analyses, which are sample-controlled thermogravimetry (SCTG), thermogravimety combined with evolved gas analysis using mass spectrometry (TG–MS) and simultaneous measurement of differential scanning calorimetry and X-ray diffractometry (XRD–DSC). The thermal processes of anhydrous zinc acetate in dry gas atmosphere by conventional linear heating experiment initiated with the sublimation around 180 °C, followed by the fusion and the decomposition over 250 °C. SCTG was useful to interpret clearly the successive reaction because the high-temperature parallel decompositions were effectively inhibited. The thermal behavior changed dramatically by introducing water vapor in the atmosphere and the thermal process was quite different from that in dry gas atmosphere. Zinc oxide (ZnO) was formed only in a humidity-controlled atmosphere, and could be easily synthesized at temperatures below 300 °C. XRD–DSC equipped with a humidity generator revealed directly the crystalline change from Zn(CH₃CO₂)₂ to ZnO. A detailed thermal process of Zn(CH₃CO₂)₂·2H₂O and the effect of water vapor are discussed.     

The effect of humidity on dehydration behavior of nitrofurantoin monohydrate studied by humidity controlled simultaneous instrument for X-ray Diffractometry and Differential Scanning Calorimetry (XRD–DSC)

The dependence of thermal dehydration behavior of nitrofurantoin monohydrate on humidity was studied. Difference in observed crystallinity of resulting anhydrates under three humidity conditions is discussed in relation to the effect of water vapor molecules. Thermal dehydration of nitrofurantoin monohydrate was measured using a humidity controlled simultaneous measurement instrument for X-ray Diffractometry (XRD) and Differential Scanning Calorimetry (DSC) in dry, 27 °C 91% RH and 60 °C 90% RH nitrogen. Dehydration of nitrofurantoin in dry nitrogen gave a mixture of crystalline and amorphous anhydrates in the temperature range of 124–180 °C followed by crystallization around 185–190 °C. Whereas, dehydration in high humidity atmosphere (60 °C 90% RH or 17.7% H₂O–82.3% N₂) gave well crystallized anhydrate at 140 °C soon after dehydration. Dehydration in low humidity nitrogen (27 °C 91% RH or 3.2% H₂O–96.8% N₂) gave not totally crystalline anhydrate, which became pure crystalline at around 190 °C. The effect of high humidity on dehydration and crystallinity of the resulting anhydrate can be attributed to the role of water vapor molecules in two ways such as the acceleration of molecular mobility and high molecular diffusion rate of nitrofurantoin anhydrate, and the formation of hydrogen bonding bridges quickly connecting dehydrated molecules to one another.     

Vapor pressure measurements in the range 10 Pa to 1 Pa of four pentaerythritol esters: Density and vapor–liquid equilibria modeling of ester lubricants

Vapor pressures of four pure pentaerythritol esters, PE, pentaerythritol tetrapentanoate, pentaerythritol tetraheptanoate, pentaerythritol tetranonanoate and pentaerythritol tetra 2-ethylhexanoate were measured between 334 and 476 K in a recently developed gas saturation apparatus. The experimental vapor pressure values for the four polyolesters range from 5.6 × 10⁻⁵ Pa to 0.94 Pa. These data together with density values were used to determined SAFT and PC-SAFT characteristic parameters. The linearity of molecular parameters for both models with the molecular weight permits to interpolate and extrapolate these parameters for pentaerythritol ester with linear chains. For pentaerythritol esters with ethyl-alkanoic chains, the parameters of SAFT and PC-SAFT have been estimated assuming that the slope of these straight lines is the same for PEs with linear chains that for PE with branched chains. This procedure was used to predict density of commercial POEs, estimating the molecular weight when it is not available from the viscosity at 313.15 K. PC-SAFT gives better performances than SAFT to predict density data for these four compounds at high pressures and for other PEs at atmospheric pressure. Furthermore, characteristic parameters for Soave-Redlich-Kwong and Peng Robinson EoSs were also estimated from the experimental vapor pressures and literature density values.     

Preparation of P(AN–MMA) microporous membrane for Li-ion batteries by phase inversion

A novel process was proposed for preparation of microporous poly(acrylonitrile–methyl methacrylate) (P(AN–MMA)) membranes by phase inversion techniques using ultrasonic humidifier. Being prepared by dissolving the polymer (PAN–MMA) in the N,N-dimethylformamide (DMF) solution with mechanical stirring, the homogenous casting solution was cast onto a clean glass plate. Successively, the glass plate was exposed to the water vapor produced by ultrasonic humidifier, inducing the phase inversion. It is found the pore size is much more uniform across the cross-section of the membrane than that of the porous membrane prepared by conventional water bath coagulation technique. The microporous membranes were directly obtained after the washing and drying. It had about 1–5 μm of pores and presented an ionic conductivity of 2.52 × 10⁻³ S/cm at room temperature when gelled with 1 M LiPF₆/EC-DMC (1:1 vol.%) electrolyte solution. The test cells with the gel electrolytes prepared from as-prepared microporous membranes showed stable cycling capacities, indicating that the microporous membrane, which was prepared from cheap starting materials acrylonitrile and methyl methacrylate, can be used for the gel electrolyte of lithium batteries.     

Carbon dioxide, ethylene and water vapor sorption in poly(lactic acid)

The objective of this work is to study the gas/vapor sorption in poly(lactic acid) (PLA) with a 98:2 (l:d) ratio using a quartz crystal microbalance (QCM). For that purpose, the sorption of carbon dioxide, ethylene and water vapor in poly(lactic acid) (PLA) with a 98:2 (l:d) ratio, in temperature range from 283 to 313 K and up to atmospheric pressure was measured. The measured isotherms indicate that the sorption mechanism is sorbate dependent, since carbon dioxide and ethylene seem to have predominantly a Langmuir type of mechanism while water is predominantly Henry controlled. Two temperature protocols were used and only ethylene sorption is affected by them. Comparisons with previously measured gas sorption data in PLA 80:20 using the same temperature protocol indicate that the l:d ratio plays a dominant role in gas/vapor sorption in PLA.     

Study of the formation of the porous structure of membranes during phase separation of a poly(ester sulfone) solution

The mechanism of the phase separation of a poly(ester sulfone) solution induced by water vapor and further immersion in water is studied via the methods of electron microscopy and porometry. The effect of the one-side treatment of the solution resting on a support with water on the porous structure of the formed membrane is investigated. Exposure to water vapor sufficient for penetration across the entire thickness leads to formation of a membrane with a gradient porous structure and a selective layer at the side contacting water vapor. With an increase in the rate of water sorption in the interval from 70 to 550 g/(m² h), the average pore size in the selective layer decrease from 170 to 70 nm. When a solution is treated with water vapor not through the entire thickness, a selective layer is formed inside the membrane. In this case, when the duration of treatment with water vapor decreases, the internal selective layer is shifted toward the side contacting water vapor. During instantaneous immersion in water, the selective layer is formed at the side contacting water and its pores are 20–30 nm in size.     

Recent developments in ESR techniques and results for semiconductor surface regions

In recent years new electron spin resonance (ESR)-based techniques have been developed, mostly with application to silicon-oxide interface regions. In this article we give the first full theoretical analysis for these techniques, namely photoconductive resonance (PCR) and spin dependence resonance (SDR), and a summary of results obtained to date. We also refer to some other recent ESR work on semiconductor surfaces including crystalline and amorphous hydrogenated silicon.Both PCR and SDR have sensitivities up to 2 orders of magnitude greater than ESR but are confined to samples where paramgnetic centers induced by incident light, affect the photoconductivity. This occurs through trapping and recombination processes. A number of different PCR and SDR centers have been found at silicon oxide interface regions, which were undetectable by normal ESR measurements. The PCR centers appear to be related to effects of water vapor, and occur in concentrations of order 10¹⁰ cm^-2 of oxide interface. In the case of SDR centers, they appear to be formed in the oxide and diffuse through it to the silicon interface, being also of low concentration and associated with impurity groups, whereas the centers directly detectable by ESR appear to be unfilled Si bonds.     

BARRIER PROPERTY AND STRUCTURE OF ACRYLONITRILE/ACRYLIC COPOLYMERS

A series of acrylonitrile (AN) copolymers with methyl acrylate (MA) or ethyl acrylate(EA) as comonomer (5--23 wt%) was prepared by free-radical copolymerization. The per-meability coefficients of the copolymers to oxygen and carbon dioxide were measured at1.0 MPa and at 30℃, and those to water vapor also measured at 100% relative humidityand at 30℃. All the AN/acrylic copolymers are semicrystalline. As the acrylate contentincrease, the permeability coefficients of the copolymers to oxygen and carbon dioxide areincreased progressively but those to water vapor are decreased progressively The gas per-meability coefficients of the polymers were correlated with free-volume fractions or the ratioof free volume to cohesive energy.     

Tunable UV generation at 283 nm by frequency doubling and sum frequency mixing of two semiconductor lasers for the detection of Pb

High resolution atomic absorption measurements of lead at 283 nm in a vapor cell were performed by frequency doubling an 850 nm laser diode to obtain 425 nm light, followed by sum frequency generation of the harmonic radiation with a second 850 nm laser diode.     

Infrared and Raman spectra, conformational stability, ab initio calculations, and vibrational assignments for methylaminothiophosphoryl difluoride

Infrared spectra (4000–50 cm⁻¹) of the vapor, amorphous and crystalline solids and Raman spectra (3600–10 cm⁻¹) of the liquid with qualitative depolarization data as well as the amorphous and crystalline solids of methylaminothiophosphoryl difluoride, CH₃N(H)P(=S)F₂, and three deuterated species, CD₃N(H)P(=S)F₂, CH₃N(D)P(=S)F₂, and CD₃N(D)P(=S)F₂, have been recorded. The spectra indicate that in the vapor, liquid and amorphous solid a small amount of a second conformer is present, whereas only one conformer remains in the low temperature crystalline phase. The near-infrared spectra of the vapor confirms the existence of two conformers in the gas phase. Asymmetric top contour simulation of the vapor shows that the trans conformer is the predominant vapor phase conformer. From a temperature study of the Raman spectrum of the liquid the enthalpy difference between the trans and near-cis conformers was determined to be 368±15 cm⁻¹ (4.41±0.2 kJ/mol), with the trans conformer being thermodynamically preferred. Ab Initio calculations with structure optimization using the 6-31G(d) and 6-311+G(d,p) basis sets at the restricted Hartree–Fock (RHF) and/or with full electron correlation by the perturbation method to second order (MP2) support the occurrence of near-trans (5° from trans) and near-cis (20° from cis) conformers. From the RHF/6-31G(d) calculation the near-trans conformer is predicted to be the more stable form by 451 cm⁻¹ (5.35 kJ/mol) and from the MP2/6-311+G(d,p) calculation by 387 cm⁻¹ (4.63 kJ/mol). All of the normal modes of the near-trans rotamer have been assigned based on infrared band contours, depolarization values and group frequencies and the assignment is supported by the normal coordinate calculation utilizing harmonic force constants from the MP2/6-31G(d) ab initio calculations.     

Liquid ammonia treatment of (cationic) nanofibrillated cellulose/vermiculite composites

Liquid ammonia was used to treat films of nanofibrillated cellulose (NFC), trimethylammonium-modified NFC (TMA-NFC), and their composites with vermiculite. Crystal structure, mechanical properties, water vapor permeation and water vapor adsorption of the resulting materials were investigated. Upon treatment, the crystal structure of (TMA-)NFC both in presence and absence of vermiculite changed from cellulose I to III. With the exception of TMA-NFC/vermiculite composites, pronounced effects on the addressed mechanical properties arose after exposure of the materials to ammonia. Furthermore, treatment of composite films with ammonia led to a distinct decrease in water vapor permeation. Remarkably, TMA-NFC/vermiculite composites films show the best water vapor barrier properties, highest tensile strength and highest elastic modulus after treatment with liquid ammonia. This is regarded to be at least partially a consequence of electrostatic attraction between the positively charged ammonium groups in TMA-NFC and the anionic silicate layers of vermiculite. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

High temperature corrosion of valve steels in atmosphere containing water vapor

The kinetics and mechanism of high temperature corrosion of two valve materials (X33CrNiMn23-8 and X50CrMnNiNbN21-9 steels) in water-vapor-containing atmosphere have been studied as a function of temperature (973–1,273 K) and gas composition, being the mixture of nitrogen, oxygen, and water vapor. In all experiments this atmosphere contained 50 vol.% of water vapor and the concentration of oxygen was changed from 0.001 to 50 vol.%. The oxidation kinetics have been studied thermogravimetrically in microthermogravimetric equipment, enabling the registration of weight changes of the oxidizing samples as a function of time with the accuracy of the order of 10⁻⁶ g. It has been found that the corrosion process of both steels is rather complex and can not be described by one kinetic rate law. X33CrNiMn23-8 steel, containing higher chromium concentration, shows better corrosion resistance than the X50CrMnNiNbN21-9 steel, but both these materials undergo more rapid corrosion in water vapor than in oxygen atmospheres. This phenomenon results from non-protective, heterogeneous scales, formed in water vapor, as compared to protective Cr₂O₃ scales, developing in oxygen atmosphere. It may be then concluded that the presence of water vapor in corrosive atmosphere plays a definitely negative role in corrosion processes.