1.5 mJ, 6.4 fs parametric chirped-pulse amplification system at 1 kHz

We demonstrate an optical parametric chirped-pulse amplification (OPCPA) system with the pulse energy of 1.5 mJ at a 1 kHz repetition rate. The newly developed 100 ps Ti:sapphire pump laser system, which was optically synchronized with OPCPA seed pulses, delivered 10 mJ, 400 nm pump pulses. After three-stage parametric amplification, recompression of the amplifier output from 45 ps to 6.4 fs was performed. The pulse width of 6.4 fs is, to our knowledge, the shortest ever obtained by OPCPA, and the average power of 1.5 W (1.5 mJ, 1 kHz) is believed to be the highest among few-cycle OPCPA systems.     

Development of a high-contrast,high-peak power,Ti:Sapphire/OPCPA laser system

We report on a high-contrast, high-peak power laser system, which combines both conventional laser amplification and optical parametric chirped pulse amplification (OPCPA) techniques. By employing an OPCPA system after a regenerative amplifier, we have enhanced the prepulse contrast by six orders of magnitude. A prepulse contrast of better than 4.4 × 10^?11 has been measured with a high-energy broadband pulse of 24 mJ at a 10 Hz repetition rate from the OPCPA system. With a subsequent four-pass Ti:sapphire amplifier, we have achieved an amplified energy of 279 mJ and an ultrashort recompressed amplified pulse duration of 23.5 fs. We also discuss the basic design aspects and present our preliminary experimental investigations for higher energy operation to a multijoule.     

High-power output from a compact OPCPA laser system

With a tabletop hybrid Nd:YAG-Nd:glass laser as pump source, a compact optical parametric chirpedpulse amplification(OPCPA)laser system with a peak output power of 16.7 TW and a pulse duration of120 fs has been demonstrated.Chirped pulses are amplified from 50 pJ to more than 3.1 J with an energygain of above 6×10~(10)by three LBO optical parametric amplifiers with a pump energy of 12.4 J at 532nm.After compression, a final output of 2.0-J/120-fs pulse is obtained. To the best of our knowledge,itis the highest peak output power from an OPCPA laser so far.In addition, a practical design of 1-PWlaser system based on the technique of OPCPA is also proposed.     

Yb:YAG Innoslab amplifier: efficient high repetition rate subpicosecond pumping system for optical parametric chirped pulse amplification

We report on a Yb:YAG Innoslab laser amplifier system for generation of subpicsecond high energy pump pulses for optical parametric chirped pulse amplification (OPCPA) at high repetition rates. Pulse energies of up to 20 mJ (at 12.5 kHz) and repetition rates of up to 100 kHz were attained with pulse durations of 830 fs and average power in excess of 200 W. We further investigate the possibility to use subpicosecond pulses to derive a stable continuum in a YAG crystal for OPCPA seeding.     

Broadband femtosecond OPCPA system driven by the single-shot narrow-band iodine photodissociation laser SOFIA

A two-stage optical parametric amplifier driven by a frequency-tripled beam from the high-energy iodine laser system SOFIA was built. This single-shot Optical Parametric Chirped Pulse-Amplification facility (OPCPA) and the system synchronizing the pump and signal pulses are described in detail. The chirped seed pulse of a Ti:sapphire oscillator running at the central wavelength of 800?nm is amplified in the two-stage (LBO and KDP) optical parametric amplifier over 10⁸ times. The amplified spectral bandwidth of 68?nm corresponds to the pulse duration of 14?fs when a transform-limited pulse is assumed. This implies a compressed pulse of TW power. Systematic gain measurements reveal a good match with the theoretical predictions. Signal and idler beam fluence profiles are presented. The suitability of the iodine photo-dissociation laser as a pump source for the OPCPA technique is thus proved for the first time experimentally. A distinctive feature of the iodine laser is its very narrow gain bandwidth (<0.1?cm^?1) and, therefore, the conventional chirped-pulse amplification technique does not lead to pulse durations at the femtosecond level.     

Hundred mJ, sub-picoseconds, high temporal contrast OPCPA/Yb:YAG ceramic thin disk hybrid laser system

The authors have demonstrated an optical parametric chirped-pulse amplification (OPCPA)/Yb:YAG ceramic thin disk hybrid laser system having hundred mJ level pulse energy sub-picosecond pulse duration with high temporal contrast. At an input chirped-pulse energy of 3.8?mJ from an OPCPA preamplifier an output energy of 130?mJ has been generated from multipass diode-pumped Yb:YAG ceramic thin disk amplifier. A recompressed pulse duration of 450?fs with a contrast level of less than 7.2×10^?9 at ?150?ps before the main pulse has been obtained. The contrast level is the highest value achieved in Yb:YAG chirped-pulse amplification (CPA) laser system at 100?mJ level.     

High-contrast, high-intensity laser pulse generation using a nonlinear preamplifier in a Ti:sapphire laser system

We report a high-contrast, high-intensity Ti:sapphire chirped-pulse amplification system that incorporates a nonlinear preamplifier based on optical parametric chirped-pulse amplification (OPCPA). By cooling the Ti:sapphire crystal in the final amplifier down to 77 K, the chirped-pulses are amplified to 2.9 J at a 10 Hz repetition rate without a thermal lensing effect. Pulse compression down to 19 fs duration obtained after amplification indicates a peak power of 80 TW. With the OPCPA, the temporal contrast is significantly improved to better than 7x10(-9) in a few picoseconds interval prior to the main laser pulse.     

Optical parametric chirped-pulse amplification source suitable for seeding high-energy systems

A short-pulse source based on optical parametric chirped-pulse amplification (OPCPA) technology has been developed with properties that make it a suitable seed for a high-energy OPCPA system. This source generated a diffraction-limited pulse at 910 nm with a full bandwidth of > 165 nm and a spectrum having a transform-limited pulse duration of less than 15 fs. The technique has potential for generating bandwidths > 200 nm and pulse durations < 10 fs.     

基于“神光-Ⅱ”装置的飞秒拍瓦级光学参量啁啾脉冲放大的特性分析与系统设计

用计算机仿真分析了光学参量啁啾脉冲放大（OPCPA）的特性及其影响因素（如相位失配、高阶非线性效应等）-就脉冲放大机理、时间同步、光谱漂移、增益窄化等相似问题与现有的啁啾脉冲放大技术做了比较与讨论-基于“神光-Ⅱ”装置，设计了飞秒拍瓦级OPCPA系统，以期望实现快点火- 关键词： 超短超强激光 啁啾脉冲放大 光学参量啁啾脉冲放大 数值模拟     

Multi-millijoule, nonlinear preamplifier for high intensity femtosecond Yb:YAG chirped-pulse amplification lasers at 1030 nm

We report the highest energy broadband laser pulses at a center wavelength of 1030 nm based on optical parametric chirped-pulse amplification (OPCPA). We have demonstrated amplification of 1030 nm femtosecond laser pulses from a broadband Yb oscillator to over 6.5 mJ with a total gain of greater than 10⁷ achieved in a single pass through only 56 mm of gain material at a 10 Hz repetition rate. The amplified spectral bandwidth of 10.8 nm affords recompression to a 230 fs pulse duration following amplification. As an alternative to the regenerative amplifier (RA) this system is one of the more promising candidates for realizing compact, high intensity, direct diode-pumped, high repetition rate femtosecond Yb:YAG chirped-pulse amplification (CPA) in laser systems.     

基于光束偏转的扫描式宽带光参量啁啾脉冲放大

光参量啁啾脉冲放大(OPCPA)是超短激光脉冲领域的重要技术之一,增大增益带宽对提高OPCPA的转换效率、实现宽带光参量放大具有重要的意义.本文将光束偏转和非共线OPCPA有机结合,提出了基于光束偏转的扫描式宽带OPCPA模型.分析了通过光束偏转来时刻改变非共线角,以保证各频率成分的相位匹配,从而增大增益带宽的基本原理.采用提出的扫描式宽带OPCPA,针对800 nm中心波长、带宽约为100 nm信号光的光参量放大进行了数值计算.结果表明:经过扫描式OPCPA后,信号光的带宽与放大之前几乎相同,光谱没有窄化;扫描式OPCPA比固定非共线角方式的放大极大地增加了增益带宽和转换效率,实现了宽带的光参量放大;要满足信号光各频率成分的相位匹配,达到最大的增益带宽和转换效率,需要尽量减小加载到钽铌酸钾(KTa_(1-x) Nb_xO_3, KTN)电光晶体上的电压抖动和电压延时.     

Generation of high-contrast and high-intensity laser pulses using an OPCPA preamplifier in a double CPA, Ti:sapphire laser system

We demonstrate a high-contrast, high-intensity double chirped-pulse amplification (CPA) Ti:sapphire laser system using an optical parametric chirped-pulse (OPCPA) pre- amplifier. By injecting cleaned microjoule seed pulses into the OPCPA, a temporal contrast greater than 10¹⁰ within picosecond times before the main femtosecond pulse is demonstrated with an output pulse energy of 1.7 J and a pulse duration of 30 fs, corresponding to a peak power of 60 TW at a 10 Hz repetition rate. This system uses a cryogenically-cooled Ti:sapphire final amplifier and generates focused peak intensities in excess of 10²⁰ W/cm².     

Improvement of contrast ratio in saturated OPCPA system by using pump pulse shaping and time delay control

We theoretically investigated the temporal profile of a background pedestal in a single-stage optical parametric chirped pulse amplification (OPCPA) system, and showed that the amplified spontaneous emission (ASE) prepulse in the saturation regime degrades the contrast ratio. To improve the contrast ratio in a saturated OPCPA system, a method using pump pulse shaping and the time delay control between pump and seed pulses was utilized. Through numerical simulations, the effect of the rising time and the time delay of a pump pulse on the background pedestal was subsequently investigated in terms of the contrast ratio. From the simulation results, it was determined that an optimal rising time and the time delay of the pump pulse are critical for obtaining a high-contrast broadband laser pulse from a saturated OPCPA system.     

Trends in ultrashort and ultrahigh power laser pulses based on optical parametric chirped pulse amplification

Since the proof-of-principle demonstration of optical parametric amplification to efficiently amplify chirped laser pulses in 1992,optical parametric chirped pulse amplification(OPCPA)became the most promising method for the amplification of broadband optical pulses.In the meantime,we are witnessing an exciting progress in the development of powerful and ultrashort pulse laser systems that employ chirped pulse parametric amplifiers.The output power and pulse duration of these systems have ranged from a few gigawatts to hundreds of terawatts with a potential of tens of petawatts power level.Meanwhile,the output pulse duration based on optical parametric amplification has entered the range of fewoptical-cycle field.In this paper,we overview the basic principles,trends in development,and current state of the ultrashort and laser systems based on OPCPA,respectively.     

Double-line terawatt OPCPA laser system for exciting beat wave oscillations

A double-line terawatt beat laser (BEAT) is developed for exciting beat wave oscillations. BEAT consists of two oscillators and an amplification system including optical parametric chirped-pulse amplification (OPCPA) in which two individual pulses with wavelength separations of 10–35 nm are amplified, recompressed, and focused as a single beam. The recompressed pulse trace shows that a 150-fs pulse duration full width at half maximum was modulated at a beating period of 72 fs. This beating period matches a resonant excitation of plasma wave with an electron density of 2.5 × 10¹⁸ cm^?3, resulting in excitation of a beat wave in hydrogen plasma with wave amplitude of 15 GV/m. The multiple beating oscillations can amplify the plasma wave and improve its structure. This scheme would be ideal for stabilizing the plasma wave strength in the plasma cavity and for realizing a practical laser plasma accelerator.     

Demonstration of highly efficient broadband amplification in a optical parametric chirped-pulse amplifier system

We have demonstrated highly efficient broadband amplification by an optical parametric chirped pulse amplifier (OPCPA) system that uses high energy seed pulses. The OPCPA consists of three type I B-barium borate (BBO) crystals pumped by a Q-switched Nd:YAG laser. We successfully amplified the microjoule level seed pulses to 78 mJ with a pump-to-signal optical conversion efficiency of 26% at a 10 Hz repetition rate. To our knowledge these results represent the most optically efficient OPCPA to date pumped by a typical Q-switched laser.     

基于预啁啾管理放大的掺镱锁模光纤激光器

报导了一种采用预啁啾管理放大技术实现的百飞秒级掺镱光纤激光器系统。该系统首先利用非线性偏振旋转技术搭建锁模种子激光,实现重复频率为82.3 MHz、压缩后脉宽接近180 fs的近线性啁啾稳定脉冲序列。种子脉冲通过预放大级和预啁啾管理放大级后获得了平均功率为12 W、压缩后脉宽低于100 fs的脉冲。经过预啁啾管理放大级的压缩后脉冲宽度明显优于种子激光的压缩后脉冲宽度。     

啁啾匹配OPCPA方案用于消除超短激光脉冲的预脉冲

采用了一种利用啁啾匹配光参量啁啾脉冲放大（OPCPA）技术来消除泵浦脉冲时间窗口内的预脉冲的方法,并对该方法展开了数值模拟研究。分析了泵浦光脉冲形状、预脉冲提前时间等因素对预脉冲消除效果以及信噪比提升情况的影响。通过与传统的非共线OPCPA方案对比,发现啁啾匹配OPCPA方案可以消除掉离主脉冲更近的预脉冲,且它对预脉冲的消除效果受泵浦光脉冲形状的影响较小。     

宽带光学参变啁啾脉冲放大系统的色散控制

在设计宽带光学参变啁啾脉冲放大系统时,对色散源进行了理论分析和讨论。对光学参变啁啾脉冲放大系统的色散量以及各个过程中的高阶色散对脉冲时域和频域特性的影响进行了计算。结果表明展宽器引入了非常大的色散,放大器中信号光相位变化产生的色散较大,参量晶体本身引入的色散相对较小可以忽略不计。输出脉冲宽度主要受二阶色散影响,而三阶和四阶色散主要影响脉冲的波形和信噪比,对频域影响很小。     

Broadband, high gain two-stage optical parametric chirped pulse amplifier using BBO crystals for a femtosecond high-power Ti:sapphire laser system

We design a two-stage non-collinear optical parametric chirped pulse amplifier using BBO crystals for a high-power Ti:sapphire laser system, and numerically analyze the output characteristics of the OPCPA system. We find optimal phase-matching conditions and calculate the parametric gains as a function of pump intensity and interaction length. By constructing a two-stage OPCPA system using two BBO crystals, we obtain 12 mJ output energy corresponding to a high gain of 10⁷, a pulse duration of 37 fs, and a contrast ratio of 5×10⁻⁸.