Y沸石和多级孔Y沸石封装CuPhen配合物催化性能的比较

选用常规Y沸石和经后处理法制备的多级孔Y沸石为主体,采用自由配体法将铜菲咯啉(CuPhen)配合物封装在不同Y沸石中,制备了CuPhen/Y复合催化材料。采用X射线衍射、TEM、紫外-可见光谱、N_2吸附-脱附、ICP和TG等手段对所制备复合催化材料的物化性质进行了较为详细的表征,并对封装在不同Y沸石主体中的铜配合物在不同尺寸大小反应底物中的催化氧化性能进行了比较研究。结果表明,在以双氧水为氧化剂的反应体系中,封装于多级孔Y沸石中的铜配合物在不同环烷烃氧化反应中的催化活性均高于封装在常规Y沸石中的催化活性,体现出多级孔Y沸石更为优越的主体性能。此外,同封装于常规Y沸石中的铜配合物一样,封装在多级孔Y沸石主体中的金属配合物催化剂也具有良好的稳定性。     

Y沸石和多级孔Y沸石封装CuPhen配合物催化性能的比较

选用常规Y沸石和经后处理法制备的多级孔Y沸石为主体,采用自由配体法将铜菲咯啉（CuPhen）配合物封装在不同Y沸石中,制备了CuPhen/Y复合催化材料。采用X射线衍射、TEM、紫外-可见光谱、N₂吸附-脱附、ICP和TG等手段对所制备复合催化材料的物化性质进行了较为详细的表征,并对封装在不同Y沸石主体中的铜配合物在不同尺寸大小反应底物中的催化氧化性能进行了比较研究。结果表明,在以双氧水为氧化剂的反应体系中,封装于多级孔Y沸石中的铜配合物在不同环烷烃氧化反应中的催化活性均高于封装在常规Y沸石中的催化活性,体现出多级孔Y沸石更为优越的主体性能。此外,同封装于常规Y沸石中的铜配合物一样,封装在多级孔Y沸石主体中的金属配合物催化剂也具有良好的稳定性。     

不同反荷离子的Keggin结构钼磷酸盐的热稳定性及其对异丁醛催化氧化活性的影响

用共沉淀法制备了以Keggin结构为骨架的不同反荷离子钼磷酸盐,利用FTIR、XRD等手段进行了表征。结果表明,Li、Na、K、Cs分别作为反荷离子时的杂多酸盐的热稳定性依次增强,并考察了催化剂对异丁醛一步氧化制甲基丙烯酸的催化活性,其中Cs盐的催化活性最优。     

香豆素/Betti碱主体合成及其对铷、钡离子的选择性响应(英文)

合成了一个新型香豆素/Betti碱主体化合物1,并对其进行了结构表征。在乙腈/水溶液中进行主体1和碱金属、碱土金属相关离子(Li+,Na+,K+,Rb+,Cs+,Be2+,Mg2+,Ca2+,Sr2+,Ba2+)的相互作用研究时,发现仅Rb+,Ba2+离子对主体1有敏感的紫外光谱及荧光光谱响应,而其它的碱金属、碱土金属离子无敏感性光响应。紫外光谱显示,Rb+,Ba2+离子使主体1产生明显的红移(ε=4.66×102L·(mol·cm)-1,Δ=91nm),肉眼可观察到明显的由浅黄向橙红色的颜色变化,并使主体1的荧光光谱发生一定程度的猝灭。     

金属离子对Ru-Pt/γ-Al2O3催化剂上对氯硝基苯选择加氢反应的影响

 采用混合醇还原法制备了聚乙烯吡咯烷酮(PVP)稳定的Ru-Pt/γ-Al2O3双金属催化剂,考察了其催化对氯硝基苯(p-CNB)选择加氢反应的性能,探讨了反应温度、压力、第三金属离子的种类、添加量及添加方式对反应的影响. 结果表明,以Ru-Pt/γ-Al2O3为催化剂,在1.0 MPa和50 ℃的条件下反应1 h,p-CNB的转化率可达48.2%,生成对氯苯胺(p-CAN)的选择性为87.3%. 在反应体系中添加适量的Fe3+或Sn4+离子时,在相同的反应条件下,p-CNB的转化率和p-CAN的选择性分别提高到100%和99.0%. Fe3+或Sn4+的添加量及添加方式对p-CNB的转化率有较大的影响,加入Fe2+,Co2+和Ni2+离子也有利于提高催化剂的活性和选择性. Ru-Pt/γ-Al2O3催化剂体系对其它氯硝基苯的加氢反应也有明显的催化作用.     

新催化动力学光度法(木音)花青-H2O2体系测定痕量铬(Ⅵ)

在六次甲基四铵-盐酸介质中, 痕量铬(Ⅵ)显著催化 H2O2 氧化花青褪色的指示反应, 催化反应的表观活化能为 6.84 kJ·mol-1, 建立了测定痕量铬(Ⅵ)的动力学分析法, 线性测定范围为 0～150 μg·L-1,检出限为 0.8 μg·L-1.常见离子中,除 Al3+,Cu2+,Fe3+,Fe2+ 外,其余离子不影响测定.其中 Al3+ 的干扰可用 F- 掩蔽消除, Cu2+,Fe3+,Fe2+ 的干扰可用 EDTA 掩蔽消除.本法已用于测定湖水,矿井水和电镀废水中的铬(Ⅵ).     

新催化动力学光度法Bei花青—H2O2体系测定痕量铬（Ⅵ）

在六次甲基四铵-盐酸介质中, 痕量铬(Ⅵ)显著催化 H2O2 氧化花青褪色的指示反应, 催化反应的表观活化能为 6.84 kJ·mol-1, 建立了测定痕量铬(Ⅵ)的动力学分析法, 线性测定范围为 0～150 μg·L-1,检出限为 0.8 μg·L-1.常见离子中,除 Al3+,Cu2+,Fe3+,Fe2+ 外,其余离子不影响测定.其中 Al3+ 的干扰可用 F- 掩蔽消除, Cu2+,Fe3+,Fe2+ 的干扰可用 EDTA 掩蔽消除.本法已用于测定湖水,矿井水和电镀废水中的铬(Ⅵ).     

聚合物微球固载的催化剂TEMPO在分子氧氧化环己醇过程中的催化特性（英文）

醇氧化为羰基化合物是有机合成工业中最重要的化学转变之一,在实验室研究和精细化工生产中都占有非常重要的地位.使用传统的化学计量强氧化剂(如Cr O3,KMnO4,MnO2等),不但成本高及反应条件苛刻,还会产生大量污染环境的废弃物.因此,需要大力发展高效、绿色化的醇转变为羰基化合物的氧化途径.以2,2,6,6-四甲基哌啶氮氧自由基(TEMPO)为催化剂,分子氧为氧化剂,可在温和条件下绿色化地实现醇的氧化转变.该催化氧化作用的实质是TEMPO经过单电子氧化过程转化为相应的氮羰基阳离子,该阳离子是一个具有强氧化性的氧化剂,可将伯醇和仲醇分别快速地、高转化率、高选择性地氧化为对应的醛或酮.然而,目前使用的TEMPO大多为均相催化剂,虽然表现出良好的催化活性和选择性,但反应后难以分离回收,不能再循环使用,严重制约着这一催化体系的发展.本文将TEMPO化学键合在聚合物载体上,在非均相催化剂的作用下,以期实现环已醇的分子氧氧化,将其转变为环已酮.首先采用悬浮聚合法,制备了交联聚甲基丙烯酸缩水甘油酯(CPGMA)微球,该聚合物微球表面含有大量环氧基团,为实现TEMPO的固载化提供了条件.以4-羟基-2,2,6,6-四甲基哌啶氮氧自由基(4-OH-TEMPO)为试剂,使CPGMA微球表面的环氧基团发生开环反应,从而将TEMPO键合于微球表面,制得了固载有TEMPO的聚合物微球TEMPO/CPGMA.将此非均相催化剂与Fe(NO3)3组成共催化体系,应用于分子氧氧化环己醇的催化氧化过程,深入考察了该共催化体系的催化性能,并探索研究了催化氧化机理,考察了主要条件对催化氧化反应的影响.结果表明,共催化体系TEMPO/CPGMA+Fe(NO3)3可以有效地催化分子氧氧化环己醇的氧化过程,将环己醇转化为唯一的产物环己酮,显示出良好的催化选择性.助催化剂Fe(NO3)3化学结构中的Fe3+离子和NO3–离子两种物种均参与催化过程,共同发挥助催化剂的作用,伴随着两种价态铁物种Fe(Ⅱ)与Fe(Ⅲ)的转变以及NO3–与NO2–之间的转变,固载化的氮氧自由基TEMPO不断地转变为氮羰基阳离子,该氧化剂物种使环己醇的氧化反应不断地循环进行.对于共催化体系TEMPO/CPGMA+Fe(NO3)3的使用,适宜的反应条件为TEMPO与Fe(NO3)3的摩尔比为1:1,55°C,通入常压O2.反应35 h,环己酮的转化率可达到44.1%.因此,在温和条件下,使用固载化的TEMPO,有效地实现了环己醇向环己酮的转化.此外,固载化催化剂TEMPO/CPGMA在循环使用过程中表现出良好的重复使用性能.     

Y型分子筛固载Co(Salprn)配合物的制备及催化烯烃环氧化性能

采用自由配体法将双水杨醛缩丙二胺席夫碱钴配合物Co(Salprn)封装于Y型分子筛超笼中,并通过X射线衍射、漫反射UV-Vis光谱、FT-IR光谱和差热分析技术对所制备的催化剂进行了表征。该催化剂样品( [Co(Salprn)]-Y)在苯乙烯环氧化反应中较纯配合物Co(Salprn)表现出很高的催化活性。反应条件（包括溶剂、催化剂用量、异丁醛浓度和反应时间）对催化性能有较大影响。研究结果还表明,[Co(Salprn)]-Y对其他烯烃的环氧化也具有较高催化活性。其活性顺序为苯乙烯﹥环己烯﹥环辛烯﹥正辛烯。     

碱性沸石催化对二甲苯-甲醇侧链烷基化反应的特性

用离子静电势、弱酸中毒法及红外光谱法表征了交换型和浸渍型碱金属离子沸石的酸碱性,并将其与对二甲苯-甲醇的侧链烷基化反应的活性和选择性相关联。结果表明,反应活性和选择性与催化剂酸碱性之间有较好的关系。Rb~+,Cs~+浸渍的LiX,NaX,KX沸石,通过Rb~+,Cs~+离子与体系的相互作用,被“诱发”成为有明显碱性功能的沸石催化剂。从红外光谱观察到碱金属离子沸石有一定强度的碱中心吸收带。还观察到LiX,NaX沸石上的呲啶吸附中心。     

Construction and control of plasmid DNA network

The influences of different cations on plasmid DNA network structures on a mica substrate were investigated by atomic force microscopy (AFM). Interactions between the DNA strands and mica substrate, and between the DNA strands themselves were more strongly influenced by the complex cations (Fe(phen)3(2+), Ni(phen)3(2+), and Co(phen)3(3+)) than by the simple cations (Mg2+, Mn2+, Ni2+, Ca2+, Co3+). The mesh height of the plasmid DNA network was higher when the complex cations were added to DNA samples. The mesh size decreased with increasing DNA concentration and increased with decreasing DNA concentration in the same cation solution sample. Hence, plasmid DNA network height can be controlled by selecting different cations, and the mesh size can be controlled by adjusting plasmid DNA concentration.     

Solvent Extraction of Alkali Metal Picrates by Lipophilic Cyclodextrin Derivatives

Lipophilic cyclodextrin (CD) derivatives were prepared to extract alkali metal cations from a water phase into an organic phase. The extraction equilibrium constant, K ex, was determined by the solvent extraction method using UV absorption spectroscopy. Hydroxyl groups at the carbons in the 2,6-positions of CD molecules were dipropylated to add the hydrophobicity for dissolving into organic solvents, and furthermore hydroxyl groups at the carbons in the 3-position of these derivatives were acylated as complexing sites with the alkali metal cations. These CD derivatives formed a 1 : 1 complex with alkali metal cations, except for the case of Li+, and transported the alkali metal cations from a water phase into a benzene phase. The initial concentrations of alkali metal cation and picrate anion in the water phase and that of the CD derivatives in the organic phase strongly influenced the extraction equilibrium. Extraction of the alkali metal cation by the derivative without acyl groups was not detected. K ex values of these CD derivatives are of the same order of magnitude as or larger than those of crown ethers. The order of the K ex values in all cases is Li+ < Na+ < K+ Rb+ Cs+, although these CD derivatives have no special selectivity for the alkali metal cations. The cation extraction mechanism was interpreted by an induced-fit mechanism.     

新型氮杂大环化合物的研究Ⅲ.取代不对称多齿氮杂大环化合物的合成、表征与配位性能

合成了四种以Nsp2 和Nsp3为配位原子的取代不对称多齿氮杂大环化合物 ,制备了它们与不同金属离子的配合物 ,通过元素分析和光谱表征 ,研究了配体的结构与其配位性能的关系 .以吡啶环为侧链功能基的配体L1和L2可根据其环大小选择性地识别Na+或K+离子 ,与过渡金属离子形成 1∶1型配合物 ,而与Hg2 +,Cd2 +等离子则形成1∶2型配合物 .大环配体L3与Co2 +和Na+离子形成的双核配合物中两个冠醚环和一个Na+离子形成夹心配位结构 .L5环中有两个配位中心 ,因而可同时与两个Ru2 +离子配位 .L1和L2 均表现出对不同金属离子良好的液膜传输性能和传输选择性     

新型氮杂大环化合物的研究3: 取代不对称多齿氮 杂大环化合物的合成、表征 与配位性能

合成了四种以Nsp^2和Nsp^3为配位原子的取代不对称多齿氮杂大环化合物,制备了它们与不同金属离子的配合物,通过元素分析和光谱表征,研究了配体的结构与其配位性能的关系。以吡啶环为侧链功能基的配体L^1和L^2可根据其环大小选择性地识别Na^+或K^+离子,与过渡金属离子形成1:1型配合物,而与Hg^2^+,Cd^2^+等离子则形成1:2型配合物。大环配体L^3与Co^2^+和Na^+离子形成的双核配合物中两个冠醚环和一个Na^+离子形成夹心配位结构。L^5环中有两个配位中心,因而可同时与两个Ru^2^+离子配位。L^1和L^2均表现出对不同金属离子良好的液膜传输性能和传输选择性。     

Fluorometric sensing of alkali metal and alkaline earth metal cations by novel photosensitive monoazacryptand derivatives in aqueous micellar solutions

Novel monoazacryptand-type fluorescent chemosensors, (derived from an 18-crown-6) and (derived from a 15-crown-5) both with a pyrene ring as their photoresponsive moiety, were synthesized. Their fluorescence properties for alkali metal and alkaline earth metal cations in water were then examined. The detection of metal cations was accomplished by a change in the fluorescence intensity of the host compounds, based on a photoinduced electron transfer (PET) mechanism. In aqueous solution, showed little fluorescence upon the addition of Ba2+ because of the very weak complexation with Ba2+, but the presence of micelles of polyoxyethylene(10) isooctylphenyl ether (Triton X-100) enabled to show highly sensitive and selective Ba2+ detection among alkali metal and alkaline earth metal cations. With respect to the selective fluorescent detection of important metal cations (Na+, K+, Mg2+, Ca2+) relevant to living organisms, was found to detect K+ with high selectivity in aqueous micellar solutions of polyoxyethylene(20) sorbitan monostearate (Tween-60). The selectivity for metal cations was mainly dependent on the goodness of fit of the host cavity and the metal cation size. In the presence of anionic surfactants, detected alkaline earth metal cations more effectively than alkali metal cations.     

碱金属阳离子对铁卟啉电催化CO2还原的影响

电催化CO2还原反应(CO2RR)可以有效地将温室气体转化为燃料或高附加值的化学品,从而缓解目前人类所面临的环境问题和能源危机,其中开发高效的电催化剂是至关重要的环节.近年来,研究者设计了多种高效的过渡金属配合物(包括Mn,Fe,Co,Ni和Cu)用作CO2RR分子电催化剂,并研究了其中的构效关系,例如,在分子内修饰质子给体取代基或电荷取代基可以显著提高CO2RR的催化效率.而电催化CO2RR的实际应用要在含有碱金属阳离子(例如,Na+和K+)的电解质水溶液中进行,但在已有报道中,很少有关于碱金属阳离子对CO2RR的影响.在众多的分子催化剂中,铁卟啉可以以较高的催化活性和选择性实现CO2到CO的转化.重要的是,卟啉环的刚性结构、稳定的配位环境及其骨架上官能团的易于修饰性成为研究CO2RR的构效关系的理想分子模型.基于以上考虑,本文以铁卟啉配合物为分子模型,研究了碱金属阳离子Na+和K+对电催化CO2RR的影响.首先,本文合成了简单的A4型铁卟啉化合物四-(3,4,5-三甲氧基苯基)-铁卟啉(FeP).并采用核磁共振、质谱分析、单晶衍射等表征手段对化合物进行了表征,在含有电解质的DMF溶液中测试其电催化CO2还原性能.实验结果表明,FeP可以实现高效的电催化CO2还原,催化电流随FeP的浓度呈线性增加,说明催化反应速率与催化剂浓度呈一级反应速率关系.较长时间的恒电压电解实验以及电解前后化合物的紫外-可见光谱证实了FeP的稳定性.通过气相色谱对产物进行分析,CO为主要产物,法拉第效率为95％.以上结果均表明,FeP是一个优良的分子催化剂.在此基础上,本文还发现加入Na+和K+均可以显著提升催化活性,而K+的加入使催化电流的提升更加显著,这可能是由于K+在溶液中的迁移速度比Na+更快.基于此实验现象,本文通过在FeP的第二配位层修饰1-氨-18-冠-6-醚官能团(N18C6),合成了N18C6-FeP化合物.结果表明,由于N18C6与Na+/K+之间的配位作用,使得N18C6-FeP比FeP具有更好的电催化CO2RR活性.研究表明,催化活性的提升归因于碱金属阳离子能够通过静电相互作用稳定Fe-CO2中间体.1H NMR谱证实了N18C6基团的确能够螯合碱金属阳离子.本文研究证明了碱金属阳离子对改善电催化CO2RR的积极作用,对于进一步深入了解CO2RR催化反应机理和未来合理的设计高效催化剂也都具有重要意义.     

Modeling metal cation-phosphate interactions in nucleic acids in the gas phase via alkali metal cation-triethyl phosphate complexes

Threshold collision-induced dissociation techniques are employed to determine the bond dissociation energies (BDEs) of complexes of alkali metal cations, Na+, K+, Rb+, and Cs+, to triethyl phosphate (TEP). The primary and lowest energy dissociation pathway in all cases is the endothermic loss of the neutral TEP ligand. Theoretical electronic structure calculations at the B3LYP/6-311+G(2d,2p)//B3LYP/6-31G* level of theory are used to determine the structures, molecular parameters, and theoretical estimates for the BDEs of these complexes. For the complexes to Rb+ and Cs+, theoretical calculations were performed using hybrid basis sets in which the effective core potentials and valence basis sets of Hay and Wadt were used to describe the alkali metal cation, while the standard basis sets were used for all other atoms. The agreement between theory and experiment is excellent for the complexes to Na+ and K+ and is somewhat less satisfactory for the complexes to the heavier alkali metal cations, Rb+ and Cs+, where effective core potentials were used to describe the cation. The trends in the binding energies are examined. The binding of alkali metal cations to triethyl phosphate is compared with that to trimethylphosphate.     

Vibrational study of the salicylate interaction with metallic ions and surfaces

Infrared and Raman spectroscopy are used in this work to study the metallic complexes of salicylic acid with silver and copper, comparing the interaction between salicylate and the cations (Ag+ and Cu2+) in the metal complexes with the SERS spectra when adsorbed on colloidal metal surfaces of the same metals. The salicylate complexes with the above metals were compared to those of Na+, Fe3+ and Al3+ cations. A different interaction mechanism is deduced for salicylate in the metal complex and when adsorbed on the metal surface.     

Density functional calculation of the electronic circular dichroism spectra of the transition metal complexes [M(phen)3]2+ (M = Fe, Ru, Os)

The circular dichroism spectra of the tris-bidentate metal complexes Lambda-[M(phen)3]2+, with M = Fe, Ru, Os and phen = 1,10-tris-phenanthroline, are investigated computationally, employing time-dependent density functional theory. Good agreement with experimental spectra is obtained for Ru and Os. The Lambda-[Os(phen)3]2+ spectrum is analyzed in detail. It is shown how relativistic effects red shift CD bands where the Os 5d-orbital participates to a large extent in the excitations. Further, the participation of the metal in the ligand pi --> pi exciton CD is determined to be of the order of 10%. Though solvent effects can have a noticeable effect on individual transitions and rotatory strengths, they are demonstrated to have only a very small overall effect on the resulting simulated CD spectra. For Lambda-[Fe(phen)3]2+, the results are shown to be rather sensitive to the choice of the applied hybrid and nonhybrid density functionals, and the optimized geometries based thereupon. In particular, the sign pattern of the lower-energy part (up to 33 x 10(3) cm(-1)) of the Lambda-[Fe(phen)3]2+ CD spectrum is difficult to reproduce. Some combinations of functionals and geometries yield good agreement with experiment, but no "best" approach can be devised based on the available results. Possible sources of errors in the spectrum of Lambda-[Fe(phen)3]2+ due to deficiencies in the functionals and the exchange-correlation kernels are investigated.     

Synthesis and multitopic complex formation of a photochromic bis(crown ether) based on benzobis(thiazole)

2,7-Bis[2-(6,7,9,10,12,13,15,16-octahydro-5,8,11,14,17-pentaoxabenzocyclopentadecen-2-yl)vinyl]-benzo[1,2-d;3,4-d']bisthiazole, 2, with crown ether styryl moieties substituted on a heterocyclic core, was synthesized and its complex forming ability with several metal cations was evaluated in acetonitrile by absorption and fluorescence spectroscopy. The results are compared to those for the analogous ligand possessing a single crown ether styryl moiety. Selective binding of the metal cation at the heterocyclic core of both ligands was observed only for Hg2+. Alkali and alkaline earth cations bind selectively at the crown ether moieties. Stability constants and pure spectra of defined stoichiometry were determined with the use of HYPERQUAD, a least-squares fitting program, and the results were validated in one case by subjecting the titration spectral matrix to singular value decomposition with self-modeling (SVD-SM). The multitopic ligand 2 forms relatively strong 2:2 stoichiometric complexes with K+, among the alkali metal cations, and Ba2+, among the alkaline earth metal cations, and is a promising selective optical sensor for these ions.