The electrochemical stripping determination of tin in aqueous and nonaqueous media after its extraction

The anodic stripping voltammetric and chronopotentiometric determination of tin(IV) in aqueous and nonaqueous medium after its extraction using the rotating disc electrode made of glassy carbon with the mercury film was studied. The optimum composition of nonaqueous medium for the determination of tin is 0.2 M NaBr+5×10^?5M Hg²⁺ in 20 ml of the extract +30 ml of methanol. Tin(IV) was determined by anodic stripping voltammetry or chronopotentiometry down to the concentration 10^?7M. The selective determination of tin was studied. 10^?6M of tin(IV) was determined with an error ±4–5% even in the presence of metals: Co²⁺, Ni²⁺, Cd²⁺, Zn²⁺ (5×10^?3M), Ag⁺ and Pb²⁺ (5×10^?4M), Cu²⁺ (1.5×10^?4M), Sb³⁺ and Bi³⁺ (5×10^?5M).     

Catalytic Adsorptive Stripping Voltammetry of Germanium(IV) in the Presence of Gallic Acid and Vanadium(IV)‐EDTA

A highly sensitive and selective catalytic adsorptive cathodic striping procedure for the determination of trace germanium is presented. The method is based on adsorptive accumulation of the Ge(IV)‐gallic acid (GA) complex onto a hanging mercury drop electrode, followed by reduction of the adsorbed species. The reduction current is enhanced catalytically by addition of vanadium(IV)‐EDTA. The optimal experimental conditions include the use of 0.03 mol/L HClO₄ (pH1.6), 6.0×10^?3 mol/L GA, 3.0×10^?3 mol/L V(IV), 4.0×10^?3 mol/L EDTA, an accumulation potential of ?0.10 V(vs. Ag/AgCl), an accumulation time of 120 s and a differential pulse potential scan mode. The peak current is proportional to the concentration of Ge(IV) over the range of 3.0×10^?11 to 1.0×10^?8 mol/L and the detection limit is 2×10^?11 mol/L for a 120 s adsorption time. The relative standard deviation at 5.0×10^?10 mol/L level is 3.1%. No serious interferences were found. The method was applied to the determination of germanium in ore, mineral water and vegetable samples with satisfactory results.     

Polarographic determination of glycine with a dropping copper amalgam electrode

The anodic oxidation of a dropping copper amalgam electrode in presence of dilute solutions of glycine in 0.50 M NaClO₄ has been studied. An anodic wave at ?0.28V (SCE) is observed, yielded by diffusion of glycinate anion in the solution towards the electrode surface. The wave-heights increase with the glycinate concentration (function of glycine concentration and pH value) until the anodic oxidation is controlled by the metal diffusion into mercury. The effect of pH is interpreted by attributing it to the depolarizer effects at glycinate anion even though the zwitterion is present in much larger concentrations. The applicability of anodic oxidation of a dropping copper amalgam electrode in the determination of glycine in the range of concentrations 10^?4–10^?2M with a rigorous control of pH (8.0<pH<10.5) is shown. The standard deviation of the proposed method is 4.1% and the minimum concentration determinable is in the 1×10^?4M range.     

Consecutive determination of rutin and quercetin by spectrophotometric measurements

The consecutive determination of rutin and quercetin without any pretreatment for separation was examined in methanol solutions by a conventional and a two-wavelength spectrophotometry. Based the tendency of quercetin to form more stable metal complexes compared to rutin, quercetin can be determined through the tin(II) complex formation without interference from rutin. The method was applied to the determination of quercetin in the concentration range of 3.0 × 10^?6 to 2.0 × 10^?5M.Quercetin is apt to be oxidized by oxygen rather than rutin, especially in the presence of copper(II), whereas rutin is not decomposed under such a condition. After removal of quercetin through copper(II)-catalyzed oxidation, rutin ranging in concentration from 2.0 × 10^?6 to 2.0 × 10^?M was determined by the absorbance measurement of rutin-copper(II) complex in slightly alkaline methanol media.Both rutin and quercetin were determined directly by two-wavelength spectrophotometry, without adding any complex forming metals; the lower limit of detection was about 1.0 × 10^?5M. The method was extended to the determination of a smaller amounts of rutin and quercetin using the absorption peaks of their zirconium(IV) complexes, and the determination of both components in the range of 5.0 × 10^?6 to 3.0 × 10^?5M was made with a relative error of within ±4%.     

Kinetic studies of a catalyzed metalloporphyrin formation

Kinetics of the incorporation of mercury(II) ion in tetra (p-trimethylammoniumphenyl)porphine have been investigated in aqueous solution at 30.0°C and 0.2 M (NaNO₃) ionic strength. The reaction was found to be first order each in mercury(II) and the porphyrin. The forward (formation) and the reverse (dissociation) rate constants were found to be 1.9 ± 0.2 × 10³ M^?1 s^?1 and 7 ± 2 × 10⁶ M^?1 s^?1, respectively. Kinetics of zinc(II) incorporation in tetra(p-trimethylammoniumphenyl)porphine catalyzed by mercury(II) were also investigated. This catalysis is explained in terms of steady-state formation of mono mercury(II) porphyrin followed by zinc(II) displacement of mercury(II) ion from the porphyrin. Such a mechanism also illustrates the importance of porphyrin core deformation to metal incorporation.     

Mercury ion selective poly(aniline) solid contact electrode based on 2-mercaptobenzimidazol ionophore

A mercury(II) ion selective poly(aniline) solid contact electrode based on 2-mercaptobenzimidazol (2MBI) ionophore as a sulfur containing sensing material was successfully developed. The electrode exhibits a good linear response of 29.1 mV/decade (at 20 ± 0.2°C, r ² = 0.997) within the concentration range of 1 × 10^?2?1 × 10^?7 M Hg(II). The composition of this electrode was: ionophore 0.100, polyvinylchloride (PVC) 0.330, dibutylphthalate (DBP) 0.470, potassiumtetrakis(4-chlorophenyl)borate (KTpCIPB) 0.090, and oleic acid (OA) 0.010. A poly(aniline) solid contact electrode based on 2MBI with DBP and OA plasticizers exhibited the best response characteristics of the results obtained for similarly coated wire type electrodes and solid contact electrodes based on only one DBP plasticizer. The electrode shows good selectivity for mercury(II) ions in comparison with alkali, alkaline earth, transition and heavy metal ions. This electrode is suitable for use with aqueous solutions of pH 3.3?C8.0 and the standard deviation in the measured EMF difference was ±0.5 mV in a mercury nitrate sample solution of 1.0 × 10^?2 M and ±1.1 mV in a mercury nitrate sample solution of 1.0 × 10^?3 M. The stabilization time was less than 15 min and the response time was less than 33 s. The electrode was applied as a sensor for the determination of Hg(II) content in a sea water sample and some amalgam alloys. The results show good correlation with data obtained by atomic absorption spectrometry.     

A novel catalytic adsorptive stripping voltammetric method for the determination of germanium ultratraces in the presence of chloranilic acid and the V(IV)·HEDTA complex

A novel, sensitive catalytic adsorptive stripping voltammetric procedure which can be used to determine trace amounts of germanium is described. The method is based on the interfacial accumulation of the complex formed by Ge(IV) and the product of the reduction of chloranilic acid on the hanging mercury drop electrode or the renewable silver amalgam film electrode, and its subsequent reduction from the adsorbed state followed by the catalytic action of the V(IV)·HEDTA complex. The presence of V(IV)·HEDTA greatly enhances the adsorptive stripping response of Ge. The reduction of the Ge(IV) in the presence of chloranilic acid and V(IV)·HEDTA was investigated in detail and the effects of pH, electrolyte composition, and instrumental parameters were studied. Under optimal conditions, the catalytic peak current of germanium exhibited good linearity for Ge(IV) concentrations in the range of 0.75–60 nM (for 60 s of accumulation at −0.1 V, r² = 0.995) and a low limit of detection (LOD = 0.085 nM). The procedure was successfully applied to determine Ge in water samples.

     

Kinetic fluorometric methods for the determination of phosphates at the nanogram level using a lead(II)-catalyzed pyridoxal 2-pyridylhydrazone-hydrogen peroxide reaction

Fluorometric methods for the determination of phosphate (1.5 × 10^?6–3.1 × 10^?6M), diphosphate (7.0 × 10^?7–2.0 × 10^?6M), and triphosphate (2.0 × 10^?7–2.7 × 10^?6M) are described. The analytical procedure is based on the inhibition of polyphosphate ions on the oxidation of pyridoxal 2-pyridylhydrazone (PPH) by hydrogen peroxide, catalyzed by low concentrations of lead(II) ions. The reactions are followed by means of the rate of appearance of the fluorescence (λ_ex = 355 nm, λ_em = 425 nm). The effect of the variables is studied. The kinetic parameters of the reactions are reported and rate equations are suggested. The results are interpreted according to the discernment of the chemistry of complex formations.     

Reactivity of selected volatile organic compounds (VOCs) toward the sulfate radical (SO4−)

Rate constants for a series of alcohols, ethers, and esters toward the sulfate radical (SO₄^?) have been directly determined using a laser photolysis set‐up in which the radical was produced by the photodissociation of peroxodisulfate anions. The sulfate radical concentration was monitored by following its optical absorption by means of time resolved spectroscopy techniques. At room temperature the following rate constants were derived: methanol ((1.6 ± 0.2) × 10⁷ M^?1 s^?1); ethanol ((7.8 ± 1.2) × 10⁷ M^?1 s^?1); tert‐butanol ((8.9 ± 0.3) × 10⁵ M^?1 s^?1); diethyl ether ((1.8 ± 0.1) × 10⁸ M^?1 s^?1); MTBE ((3.13 ± 0.02) × 10⁷ M^?1 s^?1); tetrahydrofuran (THF) ((2.3 ± 0.2) × 10⁸ M^?1 s^?1); hydrated formaldehyde ((1.4 ± 0.2) × 10⁷ M^?1 s^?1); hydrated glyoxal ((2.4 ± 0.2) × 10⁷ M^?1 s^?1); dimethyl malonate (CH₃OC(O)CH₂C(O)OCH₃) ((1.28 ± 0.02) × 10⁶ M^?1 s^?1); and dimethyl succinate (CH₃OC(O)CH₂CH₂C(O)OCH₃) ((1.37 ± 0.08) × 10⁶ M^?1 s^?1) where the errors represent 2σ. For the two latter species, we also measured the temperature dependence of the corresponding rate constants. A correlation of these kinetics with the bond dissociation energy is also presented and discussed. © 2001 John Wiley & Sons, Inc. Int J Chem Kinet 33: 539–547, 2001     

A kinetic determination of ultramicroquantities of some biologically active substances

A new kinetic method for the determination of ultramicroquantities of adrenaline, noradrenaline, thyroxine, and 5-hydroxytryptophan is presented. The method is based on the effect of these organic substances on the oxidation of pyrocatechol violet with hydrogen peroxide, catalyzed by Cu(II) ions.In order to find out the experimental conditions under which this effect is optimum, the kinetics of the above-mentioned indicator reaction in the presence of the compounds to be determined was studied in detail.Adrenaline and noradrenaline were determined at concentrations ranging from 2.0 × 10^?6 to 8.0 × 10^?6M, thyroxine at concentrations varying from 1.0 × 10^?6 to 10.0 × 10^?6M, and 5-hydroxytryptophan over the concentration range 7.7 × 10^?7–32.0 × 10^?7M. In these determinations the standard deviation was lower than 10%.     

Anodic stripping voltammetry of germanium at the hanging mercury drop electrode

The Ge(IV)—Ge(0) system was investigated by cyclic and stripping voltammetry at HMDE in acidic pyrogallol medium and in phosphate, borate and carbonate buffers. It was found that germanium electrodeposited from dilute Ge(IV) solutions dissolved anodically forming two peaks corresponding to the oxidation of the unstable homogeneous and stable heterogeneous amalgams. Both peaks can be exploited analytically for the determination of traces of germanium but due to the complex nature of the germanium amalgam the sensitivity and reproducibility of the determinations are lower compared to the results obtained for metals well-soluble in mercury.     

Untersuchungen zur indirekten mechanisierten katalytisch-spektralphotometrischen bestimmung von α-aminopolycarbonsäuren und phosphaten

α-Aminopolycarbonic acids and condensed phosphates are inhibitors in the iron-catalysed oxidation of p-phenetidine with hydrogen peroxide. By means of a flow-through system the inhibiting properties of seven α-aminopolycarbonic acids and technically important phosphates were investigated and the results are explained in terms of complex formation by the inhibitors. An automated determination is possible for some α-aminopolycarbonic acids (tetra-, penta- and hexa-acids) in a concentration range from 2.5 × 10^?7 to 2.5 × 10^?6M with good reproducibility (relative standard deviation about ±2% in the middle concentration range).     

Decomposition of meta- and para-phenylphenol during ozonation process

The decomposition of meta-phenylphenol (m-PP) and para-phenylphenol (p-PP) in a heterogeneous gas-liquid system using ozone was investigated. The influence of different reaction parameters such as ozone and PP isomers concentration as well as pH and temperature of the reaction mixture on the PP decay rate was determined. The second-order rate constants for the direct reaction of molecular ozone, determined in a homogeneous system, were (5.85 ± 0.35) × 10² M^?1 s^?1 and (8.90 ± 0.33) × 10² M^?1 s^?1 for m-PP and p-PP, respectively. The rate constants for the reaction of m-PP and p-PP with ozone increased with increasing pH. The reaction rate constants with ozone were found to be (1.75 ± 0.02) × 10⁹ M^?1 s^?1 and (1.86 ± 0.02) × 10⁹ M^?1 s^?1 for m-PP and p-PP anions, respectively.     

THE INTERACTION OF 2-AMINO-2-HYDROXYMETHYL-1,3-PROPANEDIOL WITH COBALT(II) AND MANGANESE(II) IONS

Abstract

The stepwise complex formation between 2-amino-2-hydroxymethyl-1,3-propanediol (TRIS) with Co(II) and Mn(II) was studied by potentiometry at constant ionic strength 2.0 M (NaClO₄) and T = (25.0 ± 0.1)°C, from pH measurements. Data of average ligand number (Bjerrum's function) were obtained from such measurements followed by integration to obtain Leden's function, F ₀(L). Graphical treatment and matrix solution of simultaneous equations have shown two overall stability constants of mononuclear stepwise complexes for the Mn(II)/TRIS system (β₁ = (5.04 ± 0.02) M^?1 and β₂ = (5.4 ± 0.5) M^?2) and three for the Co(II)/TRIS system (β₁ = (1.67 ± 0.02) × 10² M^?1, β₂ = (7.01 ± 0.05) × 10³ M^?2 and β₃ = (2.4 ± 0.4) × 10⁴ M^?3). Slow spontaneous oxidation of Co(II) solutions by dissolved oxygen, accelerated by S(IV), occurs in a buffer solution TRIS/HTRIS⁺ 0.010/0.030 M, with a synergistic effect of Mn(II).     

Cathodic stripping voltammetry: Part I. Determination of organic sulfur compounds,flavins and porphyrins at the sub-micromolar level

The experimental parameters of cathodic stripping voltammetry have been studied and optimised, and the use of a cell with a mercury pool electrode has been proposed. The technique is valuable for the determination of several classes of organic compounds, including thiols, disulfides, flavins, flavones, pterins and porphyrins at concentrations as low as 1×10^?8M. In most cases the measurement precision at the 2×10^?7M level is ±3–5%, which is similar to that of anodic stripping voltammetry. Detailed investigations were made of the electrode reaction mechanisms of cysteine, cystine, riboflavin and hemoglobin. All thiol compounds were found to adsorb strongly on mercury and chemically react with it to form a film of a mercury-thiol compound. Some closely-related thiols, e.g. 2- and 6-mercaptopurine, produced stripping peaks at well-separated potentials. Selectivity could be achieved with some thiol mixtures by adjustment of the deposition potential.     

Kinetic Study of the Bromine-Catalyzed Isomerization of Maleic Acid in Aqueous Ce(IV)-Br−-H2SO4 Medium

The presence of ceric and bromide ions catalyzes the isomerization of maleic acid (MA) to fumaric acid (FA) in aqueous sulfuric acid. A kinetic study of this bromine-catalyzed reaction was carried out. The reaction between ceric ion and maleic acid is first order with respect to Ce(IV). For [Ce(IV)]₀=5.0×10^?4 M, [H₂SO₄]₀=1.2 M, μ=2.0 M (adjusted by NaClO₄), and [MA]₀=(0.5–1.0)M, the observed pseudo-first-order rate constant (k₀₃) at 25° is k₀₃=7.622×10^?5 [MA]₀/(1+0.205[MA]₀). The reaction between ceric and bromide ions is first order with respect to Ce(IV). For [Ce(IV)]₀=5.0×10^?4 M, [H₂SO₄]₀=1.2 M, μ=2.0 M, and [Br^?]₀=(0.025–0.150)M, the pseudo-first-order rate constant (k₀₂) at 25° is k₀₂= (4.313±0.095)x10^?2[Br^?]²+(2.060±0.119)x10^?3[Br^?]. The reaction of Ce(IV) with maleic acid and bromide ion is also first order with respect to Ce(IV). For [Ce(IV)]₀=5.0×10^?4 M, [MA]₀=0.75 M, [H₂SO₄]₀=1.2 M, μ=2.0 M, and [Br^?]₀= (0.025–0.150)M, the pseudo-first-order rate constant (k₀₃) at 25° is k₀₃= (5.286±0.045)x10^?2[Br^?]²+(3.568±0.056)x10^?3[Br^?]. For [Ce(IV)]₀=5.0 × 10^?4 M, [Br^?]₀=0.050 M, [H₂SO₄]₀=1.2 M, μ=2.0 M, and [MA]₀=(0.15–1.0)M at 25°, k₀₃=(2.108×10^?4+2.127×10^?4[MA]₀)/(1+0.205[MA]₀). A mechanism is proposed to rationalize the results. The effect of temperature on the reaction rate was also studied. The energy barrier of Ce(IV)—Br^? reaction is much less than that of Ce(IV)—MA reaction. Maleic and fumaric acids have very different mass spectra. The mass spectrum of fumaric acid exhibits a strong metastable peak at m/e 66.5.     

Determination of Hg(II) ions in water samples by a novel Hg(II) sensor,based on calix[4]arene derivative

A PVC membrane electrode for Hg(II) ions, based on a new cone shaped calix[4]arene (L) as a suitable ionophore was constructed. The sensor exhibits a linear dynamic in the range of 1.0 × 10^?6–1.0 × 10^?1 M, with a Nernstian slope of 29.4 ± 0.4 mV decade^?1, and a detection limit of 4.0 × 10^?7 M. The response time is quick (less than 10 s), it can be used in the pH range of 1.5–4, and the electrode response and selectivity remained almost unchanged for about 2 months. The sensor revealed comparatively good selectivity with respect to most alkali, alkaline earth, and some transition and heavy metal ions. It was successfully employed as an indicator electrode in the potentiometric titration of Hg²⁺ ions with potassium iodide, and the direct determination of mercury content of amalgam alloy and water samples.     

Anodic stripping voltammetry of hexavalent molybdate

The anodic stripping voltammetry of hexavalent molybdate was investigated with a hanging mercury drop electrode in phosphate-borate buffer solution of pH 5.8–6.7. It was found that the deposition reaction was limited by the diffusion of the protonated molybdate ion, and the anodic stripping reaction was kinetically controlled by the dissolution of the deposited molybdate. A calibration curve for the anodic peak current versus Mo(VI) concentration was linear when Mo(VI) was within the range of 7×10^?6M and 2×10^?4M at pH 5.80. Various effects for the calibration curve were studied, and its application for the determination of Mo(VI) was discussed.     

Determination of ruthenium as ruthenate by stripping voltammetry

Stripping voltammetric analysis of ruthenium with a platinum RDE was studied in the concentration range from 5×10^?7 to 1.2×10^?5M RuO₄^2?, where linear dependence of the anodic peak height on the ruthenate concentration was obtained. Special attention has been paid to a simple preparation of the sample for analysis. Ruthenate can be prepared directly in the electrolytic vessel from the ruthenium compounds by oxidation with potassium persulphate in alkaline medium. As a supporting electrolyte 10^?2 to 5×10^?2M K₂S₂O₈ with 10^?1 to 1 M KOH was used.     

Figure‐eight Octaphyrin Bis‐Ge(IV) Complexes: Synthesis,Structures, Aromaticity,and Chiroptical Properties

Highly twisted structures of expanded porphyrin provide a prominent basis to unravel the relationship between aromaticity and chirality. Here we report the synthesis of bis‐Ge(IV) complexes of [38]octaphyrin that display rigid figure‐eight structures. Two bis‐Ge(IV) [38]octaphyrin isomers with respect to the stereochemistry of the axial hydroxy groups on the germanium ions were obtained and found to be aromatic. Upon oxidation with MnO₂, these [38]octaphyrin complexes were converted to a single syn‐type isomer of [36]octaphyrin with retained figure‐eight conformation. The enantiomers have been successfully separated by HPLC equipped with a chiral stationary phase. While aromatic [38]octaphyrin Ge(IV) complexes showed quite large molar circular dichroism of up to Δ?=1500 M^?1cm^?1 with a dissymmetry factor g_abs of 0.035, weakly antiaromatic [36]octaphyrin Ge(IV) complexes underscored moderate values; Δ?=540 M^?1cm^?1 with g_abs of 0.023. Thus, the figure‐eight octaphyrin scaffold has been proved to be an attractive platform for novel chiroptical materials with tunable aromaticity.