On-line coupling of subcritical water extraction with high-performance liquid chromatography via solid-phase trapping

Although ambient water is very polar and cannot dissolve many organic species, water at elevated temperatures behaves like a polar organic solvent. Thus, subcritical water has been proven to be an effective extraction fluid for several classes of organic compounds. While solvent trapping was used to collect the extracted analytes in most of previous subcritical water extractions, sorbent trapping has also been developed for subcritical water extraction. In this study, an on-line system for subcritical water extraction and high-performance liquid chromatography (HPLC) was built and tested. A sorbent trap was used as the interface between subcritical water extraction and HPLC. Several shut-off valves have been utilized to switch the system from one mode to another (e.g., from the extraction mode to HPLC mode). The coupling technique of subcritical water extraction and HPLC eliminates the liquid-liquid extraction used in solvent trapping subcritical water extraction and provides higher sensitivity. Compared to the off-line system reported in an earlier work, the operation of this on-line system is even easier. Some peak broadening occurred after the coupling the water extraction with HPLC for the analytes studied. The performance of this on-line system was evaluated by the extraction and determination of caffeine, nitrotoluenes, polychlorinated biphenyls, chlorophenols and anilines.     

Temperature effect on peak width and column efficiency in subcritical water chromatography

Subcritical water has been recently employed as the mobile phase to eliminate the use of organic solvents in reversed-phase liquid chromatography. Although the influence of temperature on retention in subcritical water chromatography has been reported, the temperature effect on peak width and column efficiency has not yet been quantitatively studied. In this work, several polar and chlorinated compounds are separated using pure subcritical water on Zorbax RX-C8, PRP-1 (polystyrene-divinylbenzene), Hypersil ODS, and ZirChrom-polybutadiene columns. Isothermal separations are performed at temperatures ranging from 60 degrees C to 160 degrees C. The retention time and peak width of analytes are reduced with increasing temperature. However, the column efficiency is either improved or almost unchanged with the increasing temperature in the low-temperature range (lower than the 100 degrees C to 120 degrees C range), but it is decreased when temperature is further raised in the high-temperature range (higher than the 100 degrees C to 120 degrees C range). Therefore, a maximum in column efficiency is obtained at temperatures within the 100 degrees C to 120 degrees C range in most cases.     

Subcritical water: Use in chemical analysis

The review shows prospects of the use of subcritical water instead of organic solvents and aqueous–organic mixtures at different stages of analysis. Subcritical water was applied to the extraction of target compounds from natural samples, such as soils, sand, and plant raw materials. The use of subcritical water expands possibilities of HPLC. The use of subcritical water as an eluent in HPLC is complicated by the possible destruction of the adsorbent and the decomposition of substances to be determined at elevated temperatures. Adsorbents based on zirconium and titanium oxides, some polymeric adsorbents, and porous graphitized carbon are stable in the medium of subcritical water. Subcritical water can be used at several stages of analysis, for example, for the extraction and subsequent chromatographic separation of analytes.     

Modeling of retention of adrenoreceptor agonists and antagonists on polar stationary phases in hydrophilic interaction chromatography: a review

Retention prediction models for reversed-phase liquid chromatography (RPLC) have been extensively studied owing to the fact that RPLC remains the most widely used chromatographic technique especially in the field of pharmaceutical and biomedical analyses. However, RPLC is not always the method of choice for the analysis of some compounds that have high polarity. Hydrophilic interaction chromatography (HILIC) has been gaining interest in the last few years as an alternative option to RPLC for the analysis of polar and hydrophilic analytes. HILIC is a variant of normal-phase liquid chromatography, but utilizes water in a water-miscible organic solvent as the eluent in conjunction with a hydrophilic stationary phase. The present review aims to summarize recent contributions on the development of retention prediction models for a group of basic analytes, namely, the adrenoreceptor agonists and antagonists, on different polar stationary phases. The use of multiple linear regression and artificial neural networks in model building is highlighted.     

Comparison of extraction procedures for the determination of arsenic and other elements in lobster tissue by inductively coupled plasma mass spectrometry

A variety of extraction procedures were evaluated for the extraction of arsenic and other analytes from lobster tissue samples using inductively coupled plasma mass spectrometry (ICP-MS) detection. Soxhlet, room temperature mixing, sonication, microwave assisted, supercritical carbon dioxide and subcritical water extractions were evaluated for a variety of solvent systems and optimum conditions determined using a partially defatted Lobster Hepatopancreas marine certified reference material, TORT-2 (National Research Council of Canada). The solubility trends and solvents into which the analytes extracted gave an indication as to the polar/non-polar nature of the compounds present. Analytes that prefer water are probably more polar or inorganic, while those preferring methanol solutions are less polar or organic in nature. Arsenic, cadmium, cobalt, molybdenum and selenium were probably all present in TORT-2 in both polar inorganic and non-polar organic forms. While TORT-2 may have contained similar amounts of selenium in both forms, the results suggested that more of the arsenic was present as less polar or more organic compounds, and cobalt existed mainly as more polar or inorganic species. Most of the extraction techniques suggested that, although there may be some less polar organic forms present, more of the cadmium was probably present as polar inorganic compounds. Additionally, most techniques indicated that molybdenum was possibly all less polar or more organic in nature. In general, microwave assisted extraction (MAE) yielded comparable or improved recoveries for all of the analytes monitored and usually required less solvent. Additionally, MAE proved to be the mildest, fastest, least complicated and most reproducible extraction technique evaluated. MAE at 75 degrees C for 2 min exposure time yielded quantitative recovery of arsenic from TORT-2. These conditions were evaluated for lobster tissue samples purchased from a local restaurant. Separate evaluation of the lobster meat and organs resulted in quantitative recoveries of arsenic from both tissue samples. The results indicated that the extraction efficiencies might have some dependence upon the extraction technique, extraction conditions, analyte, solvent, and sample matrix.     

Applications of ethylammonium and propylammonium nitrate solvents in liquid-liquid extraction and chromatography

Ethyl- and propylammonium nitrate are novel ionic solvents, liquid at room temperature, suitable for use as selective solvents for the isolation of analytes containing proton donor functional groups (alcohols, amines, phenols, carboxylic acids, etc.) by liquid-liquid distribution. These solvents form immiscible solvent pairs with non-polar aliphatic and aromatic hydrocarbons, ethers and alkyl halide solvents (e.g., methylene chloride, chloroform). Analytes can be recovered from the ionic solvents by back-extraction into ah organic solvent after dilution with water or pH buffer or, preferably, by extractive derivatization when gas chromatography is used for the analyses, avoiding the accumulation of salt on the column that results in poor baseline stability. Alkylation, acylation and particularly silylation are suitable methods for extractive derivatization using standard reaction conditions. Applications are presented for the isolation of polar analytes from an urban dust, shale oil and urine samples and for the determination of low-molecular-weight alcohols in gasahol and glycerol in soap. Liquid-liquid chromatographic systems with the liquid organic salt as stationary phase can be used to predict distribution constants for a particular separation and for the separation of polar solutes, particularly isomeric compounds possessing a proton donor functional group.     

Water-immiscible solvents as diluents in reversed-phase liquid chromatography

It has recently been shown that the use of strong organic solvents as diluent is possible in RPLC, provided that the solvent used as diluent is retained more strongly by the column than the analytes in the sample. In this study, the phenomenon was further studied experimentally using several water-immiscible solvents (ethyl acetate, isopropyl acetate, and methyl isobutyl ketone) and several model analyte compounds. In all cases, analyte peak distortion was minimal provided the analyte eluted earlier than the diluting solvent, in contrast to substantial broadening and distortion when the analyte eluted after the diluting solvent. The potential analytical utility of this approach is discussed, and an example of a practical application is also presented.     

Packed column supercritical fluid chromatography with light-scattering detection. II. Retention behaviour of squalane and glucose with mixed mobile phases

Summary Evaporative light scattering detectors can be used to detect organic substances without chromophoric groups in packed column supercritical fluid chromatography (SFC). A detector of this type has been used to detect squalane and glucose after SFC with various packed columns and binary mobile phases. In this study, the amount of organic modifier in carbon dioxide/modifier mixtures was varied. The results give further insight into the mechanisms that influence retention behaviour in packed column separations with super- and subcritical mobile phases. Squalane is an ideal non-polar test solute which shows long retention times on non-polar columns while its elution can be accelerated by non-polar modifiers in carbon dioxide. Glucose is an extremely polar solute containing hydroxyl groups. Elution of this sugar can be improved with polar modifiers. Column packings with polar end groups lead to high capacity ratios and long retention times for glucose. Most columns used in this study contained silica-based packing materials. For purposes of comparison, a polymeric packing (HEMA RP-18) was also employed.     

Capillary liquid chromatography using a hydrophilic/cation-exchange monolithic column with a dynamically modified cationic surfactant

A novel form of reversed-phase liquid chromatography (RPLC) by the dynamically modified hydrophilic interaction monolithic column has been described in this paper. A porous poly(SPMA-co-PETA) monolith with strong cation-exchange (SCX) was prepared and the resulting monolith showed a typical hydrophilic interaction chromatography (HILIC) mechanism at higher organic solvent content (ACN% > 50%). The good selectivity for neutral, basic and acidic polar analytes was observed in the HILIC mode. In order to increase the hydrophobic interaction, the monolith with SCX was dynamically modified with a long-chain quaternary ammonium salt, cetyltrimethylammonium bromide (CTAB), which was added to the mobile phase. CTAB ions were adsorbed onto the surface of the SCX monolithic material, and the resulting hydrophobic layer was used as the stationary phase. Using the dynamically modified SCX monolithic column, neutral, basic and acidic hydrophobic analytes were well separated with the RPLC mode.     

Multidimensional liquid chromatography system with an innovative solvent evaporation interface

An orthogonal two-dimensional liquid chromatographic (2D-LC) system was developed by using a vacuum-evaporation loop-type valve interface. Normal-phase liquid chromatography (NPLC) with a bonded CN phase column was used as the first dimension, and reversed-phase liquid chromatography (RPLC) with a C(18) column was used as the second dimension. All the solvents in the loop of the interface were evaporated at 90 degrees C under vacuum conditions, leaving the analytes on the inner wall of the loop. The mobile phase of the second dimension dissolved the analytes in the loop and injected them onto the secondary column, allowing an on-line solvent exchange of a selected fraction from the first dimension to the second dimension. The chromatographic resolution of analytes on the two dimensions was maintained at their optimal condition. Sample loss due to evaporation in the interface was observed that depended on the boiling point of the compound. Separation of sixteen polycyclic aromatic hydrocarbon mixtures and a traditional Chinese medicine Angelica dahurica was demonstrated.     

A trapping column for the coupling of reversed-phase liquid chromatography and capillary gas chromatography

A new technique for coupling reversed-phase liquid chromatography (RPLC) with gas chromatography is described. A fraction eluting from an RPLC column is trapped on a short column packed with polymeric adsorbent. After the mobile phase has been displaced with water, the analytes are desorbed with ethyl acetate. Following a delay time to enable the water to be flushed to waste, the ethyl acetate containing the analytes is introduced into the gas chromatograph under conditions suitable for partially concurrent solvent evaporation, i.e. below the solvent boiling point and at a rate just exceeding the evaporation rate. Post-column addition of water to the RPLC eluent helps to prevent breakthrough of compounds which are only modestly retained on the trapping column. The relationship between the capacity factors of the analytes on the trapping column and the required dilution factor is discussed. Polycyclic aromatic hydrocarbons are used as test compounds to study the system.     

Impact of column temperature and mobile phase components on selectivity of hydrophilic interaction chromatography (HILIC)

The retention mechanism and chromatographic behavior for different polar analytes under hydrophilic interaction chromatography (HILIC) conditions have been studied by application of different mobile phases and stationary phases to various analytes at different temperatures. In addition to the commonly accepted mechanism of analyte liquid-liquid partitioning between mobile phase and water-enriched solvent layer which is partially immobilized onto the surface of the stationary phase, hydrogen-bonding, hydrophobic interaction, and ion-exchange interactions may also be involved. The predominant retention mechanism in HILIC separation is not always easily predictable. It can depend not only on the characteristics of the analytes but also on the selection of mobile and stationary phase compositions. The objective of this review is to evaluate the potential application of column temperature and mobile phase composition toward improving HILIC selectivity. The functional groups from analyte structures, stationary phase materials and organic mobile phase solvents will be highlighted.     

Temperature as a variable in liquid chromatography: development and application of a model for the separation of model drugs using water as the eluent

The use of high temperatures in liquid chromatography allows for the use of a purely aqueous mobile phase. At elevated temperatures water possesses many of the characteristics of organic solvents in terms of eluotropic strength, as well as having a lower viscosity. A model is developed, based on data obtained using a range of model drugs, which demonstrates the relationship between temperature, flow and pressure. Experimental data from different column types, at temperatures from 40 degrees C to 180 degrees C, is presented which matches well with the predicted data from the model.     

Effects of elevated temperature and mobile phase composition on a novel C18 silica column

A novel polydentate C18 silica column was evaluated at an elevated temperature under acidic, basic, and neutral mobile phase conditions using ACN and methanol as the mobile phase organic modifier. The temperature range was 40-200 degrees C. The mobile phase compositions were from 0 to 80% organic-aqueous v/v and the mobile phase pH levels were between 2 and 12. The maximum operating temperature of the column was affected by the amount and type of organic modifier used in the mobile phase. Under neutral conditions, the column showed good column thermal stability at temperatures ranging between 120 and 200 degrees C in methanol-water and ACN-water solvent systems. At pH 2 and 3, the column performed well up to about 160 degrees C at two fixed ACN-buffer compositions. Under basic conditions at elevated temperatures, the column material deteriorated more quickly, but still remained stable up to 100 degrees C at pH 9 and 60 degrees C at pH 10. The results of this study indicate that this novel C18 silica-based column represents a significant advancement in RPLC column technology with enhanced thermal and pH stability when compared to traditional bonded phase silica columns.     

Construction of a new interface for comprehensive supercritical fluid chromatography x reversed phase liquid chromatography (SFC x RPLC)

The design of a new interface to hyphen high efficiency supercritical fluid chromatography (SFC) and fast RPLC in a comprehensive configuration is described. SFC x RPLC is a viable alternative to normal phase (NP) LC x RPLC and is characterized by high orthogonality. Compared to NPLC x RPLC an additional advantage is the expansion of supercritical carbon dioxide (CO(2)) when exposed to atmospheric pressure leading to fractions consisting of solvents that are miscible with the second dimension RPLC mobile phase. The interface consists of a two-position/ten-port switching valve equipped with two packed octadecyl silica (C(18)) loops for effective trapping and focusing of the analytes after elution from the SFC dimension. The addition of a water make-up flow to the SFC effluent prior to entering the loops is of fundamental importance to efficiently focus the solutes on the C(18) material and to reduce interferences of expanded CO(2) gas on the second dimension separation. The features of the system are illustrated with the analysis of a lemon oil sample.     

Comparisons of soxhlet extraction, pressurized liquid extraction, supercritical fluid extraction and subcritical water extraction for environmental solids: recovery, selectivity and effects on sample matrix

Extractions of a polycyclic aromatic hydrocarbon (PAH)-contaminated soil from a former manufactured gas plant site were performed with a Soxhlet apparatus (18 h), by pressurized liquid extraction (PLE) (50 min at 100 degrees C), supercritical fluid extraction (SFE) (1 h at 150 degrees C with pure CO2), and subcritical water (1 h at 250 degrees C, or 30 min at 300 degrees C). Although minor differences in recoveries for some PAHs resulted from the different methods, quantitative agreement between all of the methods was generally good. However, the extract quality differed greatly. The organic solvent extracts (Soxhlet and PLE) were much darker, while the extracts from subcritical water (collected in toluene) were orange, and the extracts from SFE (collected in CH2Cl2) were light yellow. The organic solvent extracts also yielded more artifact peaks in the gas chromatography (GC)-mass spectrometry and GC-flame ionization detection chromatograms, especially compared to supercritical CO2. Based on elemental analysis (carbon and nitrogen) of the soil residues after each extraction, subcritical water, PLE, and Soxhlet extraction had poor selectivity for PAHs versus bulk soil organic matter (approximately 1/4 to 1/3 of the bulk soil organic matter was extracted along with the PAHs), while SFE with pure CO2 removed only 8% of the bulk organic matrix. Selectivities for different compound classes also vary with extraction method. Extraction of urban air particulate matter with organic solvents yields very high concentrations of n- and branched alkanes (approximately C18 to C30) from diesel exhaust as well as lower levels of PAHs, and no selectivity between the bulk alkanes and PAHs is obtained during organic solvent extraction. Some moderate selectivity with supercritical CO2 can be achieved by first extracting the bulk alkanes at mild conditions, followed by stronger conditions to extract the remaining PAHs, i.e., the least polar organics are the easiest organics to extract with pure CO2. In direct contrast, subcritical water prefers the more polar analytes, i.e., PAHs were efficiently extracted from urban air particulates at 250 degrees C, with little or no extraction of the alkanes. Finally, recent work has demonstrated that many pollutant molecules become "sequestered" as they age for decades in the environment (i.e., more tightly bound to soil particles and less available to organisms or transport). Therefore, it may be more important for an extraction method to only recover pollutant molecules that are environmentally-relevant, rather than the conventional attempts to extract all pollutant molecules regardless of how tightly bound they are to the soil or sediment matrix. Initial work comparing SFE extraction behavior using mild to strong conditions with bioremediation behavior of PAHs shows great promise to develop extraction methodology to measure environmentally-relevant concentrations of pollutants in addition to their total concentrations.     

Subcritical water and dynamic sonication-assisted solvent extraction of fluorescent whitening agents and azo dyes in paper samples

Two low-volume solvent continuous extraction methods are applied to the extraction of paper matrices. In the methods reported here, a complex mixture of fluorescent whitening agents (FWAs) and azo dyes (AZOs) used in paper materials intended to come into contact with foodstuffs was extracted by using subcritical water extraction (SWE) and dynamic sonication-assisted solvent extraction (DSASE). Rationale for the work is based upon migration concerns of these groups of analytes from the packaging to the packaged items, thus compromising their subjective and/or objective quality. In SWE, sample was extracted in 21 min with 0.5 mL of water, whereas the DSASE method required 11 min and used 7 mL of water. DSASE was further developed by incorporating an organic modifier in order to change water polarity, thus improving extraction of moderately polar analytes. This way, modified-DSASE used a total organic volume of 0.9 mL which represents a reduction of 200 times in organic solvent consumption (200 mL versus approximately 1.0 mL) and 11 times in extraction time (2h versus 11 min) compared to the existing methods. SWE was able to extract only 9 out of 12 test analytes with average recoveries between 10 and 25% whereas modified-DSASE succeed in extracting all the target analytes with an average recovery of 89%. Complete discussion and explanation concerning these differences are provided in the text.     

Separation of nonpolar analytes using methanol-water mixtures at elevated temperatures

Pure subcritical water has been found to be an efficient mobile phase for reversed-phase separations of both polar and moderately polar compounds. However, subcritical water must be modified with organic solvent in order to elute nonpolar analytes in an efficient manner. In this study, the separation of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), and benzene, toluene, and p-xylene (BTX) was performed by using heated methanol-water mixtures as the mobile phase. Temperatures employed in this study ranged from 21 to 140 °C, while the percentage of methanol in the mobile phase ranged from 52 to 90%. The retention times of analytes were matched under different mobile phase conditions by increasing the temperature and decreasing the percentage of methanol in the mobile phase.     

硅胶色谱柱的亲水作用保留机理及其影响因素

亲水作用色谱（HILIC）是替代反相色谱（RPLC）分离强极性及亲水性化合物的另一色谱模式,其分离机理与RPLC有很大不同,具有和RPLC互补的选择性。在HILIC模式中,采用正相色谱（NPLC）中的极性固定相及含高浓度有机溶剂（通常为乙腈）的水溶液为流动相。硅胶是开发最早、研究最为深入及应用最为广泛的HILIC固定相,本文介绍了硅胶色谱柱的HILIC保留机理,详细概述了操作条件如硅胶柱类型、流动相组成及柱温对HILIC分离的影响,并对硅胶填料色谱柱的HILIC模式的发展方向与应用前景进行了展望。     

Carbon dioxide modified subcritical water chromatography

A novel method of increasing the elution strength in subcritical water chromatography (SWC) by adding CO2 to the water mobile phase is presented. Since the polarity of water reduces dramatically with increasing temperature, this property is used in SWC to create an isocratic mobile phase with tunable elutropic strength in reversed-phase separations. Unfortunately, thermal stability of the stationary phase dictates the upper temperature limit and therefore also the minimum available mobile phase polarity. As a result SWC is often not very effective at eluting non-polar analytes. However, when CO2 is blended into subcritical water, a considerable reduction in mobile phase polarity results and improves such separations. For example, in conventional SWC 1-octanol is not observed to elute from a PRP-1 column after several hours at the maximum column temperature of 200 degrees C. In contrast to this, when CO2 is present at 180atm (1atm=101325Pa) in the mobile phase, 1-octanol elutes with good peak shape in less than 4min at only 100 degrees C. The technique is applied to the separation of a variety of analytes which have previously been challenging or even not possible to analyze by conventional SWC. Further, the ability to use temperature and composition programming with the blended CO2/water mobile phase in SWC is also presented and discussed. Overall, the developed method considerably extends the range of non-polar analytes amenable to SWC analysis, while maintaining the beneficial conventional SWC features of flame ionization detection and environmental compatibility.