Transport properties of composite membranes containing silicon dioxide and Nafion

Silicon dioxide (SiO₂) nanoparticles were incorporated into Nafion 115 membranes using the sol–gel method in order to investigate their effect on water retention/transport, proton concentration, effective proton mobility, and proton conductivity. By adjusting the sol–gel reaction time, Nafion/SiO₂ membranes were fabricated with SiO₂ content ranging from 5.9 to 33.3 wt%. Because the density of the membranes decreased with increasing SiO₂ content and because dimensional changes with swelling in water of the composite membranes were less than that of unmodified Nafion 115 despite having increased water content, the theory that rigid scaffolding is formed inside the membrane is supported. Water content increases with increasing SiO₂ content due to void space formed inside the membrane. This increase in water content dilutes the protons in the membrane leading to lower proton concentration and therefore lower proton conductivity. A decreasing effective proton mobility with increasing SiO₂ content, likely due to an increase in the tortuosity of the proton-conducting pathway, also contributes to the decreasing conductivity. However, as evidenced by the similar water vapour permeance values, the SiO₂ nanoparticles do not increase the effective tortuosity of the water vapour transmission pathways.     

Fabrication and characterization of SiO2/PVDF composite nanofiber‐coated PP nonwoven separators for lithium‐ion batteries

SiO₂/polyvinylidene fluoride (PVDF) composite nanofiber‐coated polypropylene (PP) nonwoven membranes were prepared by electrospinning of SiO₂/PVDF dispersions onto both sides of PP nonwovens. The goal of this study was to combine the good mechanical strength of PP nonwoven with the excellent electrochemical properties of SiO₂/PVDF composite nanofibers to obtain a new high‐performance separator. It was found that the addition of SiO₂ nanoparticles played an important role in improving the overall performance of these nanofiber‐coated nonwoven membranes. Among the membranes with various SiO₂ contents, 15% SiO₂/PVDF composite nanofiber‐coated PP nonwoven membranes provided the highest ionic conductivity of 2.6 × 10^?3 S cm^?1 after being immersed in a liquid electrolyte, 1 mol L^?1 lithium hexafluorophosphate in ethylene carbonate, dimethyl carbonate and diethyl carbonate. Compared with pure PVDF nanofiber‐coated PP nonwoven membranes, SiO₂/PVDF composite fiber‐coated PP nonwoven membranes had greater liquid electrolyte uptake, higher electrochemical oxidation limit, and lower interfacial resistance with lithium. SiO₂/PVDF composite fiber‐coated PP nonwoven membrane separators were assembled into lithium/lithium iron phosphate cells and demonstrated high cell capacities and good cycling performance at room temperature. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1719–1726     

Nano oxides incorporated sulfonated poly(ether ether ketone) membranes with improved selectivity and stability for vanadium redox flow battery

Three kinds of sulfonated poly(ether ether ketone) (SPEEK)/nano oxide (Al₂O₃, SiO₂, and TiO₂) composite membranes are fabricated for vanadium redox flow battery (VRFB) application. The composite membranes with 5 wt% of Al₂O₃, SiO₂, and TiO₂ (S/A-5 %, S/S-5 %, and S/T-5 %) exhibit excellent cell performance in VRFB. Incorporation of nano oxides (Al₂O₃, SiO₂, and TiO₂) in SPEEK membrane improves in aspect of thermal, mechanical, and chemical stabilities due to the hydrogen bonds’ interaction between SPEEK matrix and nano oxides. The energy efficiencies (EEs) of composite membranes are higher than that of Nafion 117 membrane, owing to the good balance between proton conductivity and vanadium ion permeability. The discharge–capacity retentions of composite membranes also overwhelm that of Nafion 117 membrane after 200 cycles, indicating their good stability in VRFB system. These low-cost SPEEK/nano oxide composite membranes exhibit great potential for the application in VRFB.     

Novel proton-conductive nanochannel membranes with modified SiO2 nanospheres for direct methanol fuel cells

A novel approach is proposed to prepare a proton-conductive nanochannel membrane based on polyvinylidene difluoride (PVDF) porous membrane with modified SiO₂ nanospheres. The hydrophilic PVDF porous membrane with a 450-nm inner pore size was chosen as the supporting structure. Pristine SiO₂ with a uniform particle size of 95–110 nm was synthesized and functionalized with –NH₂ and –COOH, respectively. Through-plane channels of porous membrane and arranged functional nanoparticles in pores could contribute to constituting efficient proton transfer channels. The characteristics such as morphology, thermal stability, water uptake, dimensional swelling, proton conductivity and methanol permeability as proton exchange membranes, of the SiO₂ nanospheres, and the composite membrane were investigated. The formation of ionic channels in membrane enhanced the water uptakes and proton conduction abilities of the composite membranes. PVDF/Nafion/SiO₂–NH₂ exhibited superior proton conductivities (0.21 S cm^?1) over other samples due to several proton sites and the acid–base pairs formed between –NH₂ and –SO₃H. Furthermore, all the composite membranes exhibited improved methanol resistance compared with Nafion. Therefore, such a design based on porous membrane provided feasibility for high-performance proton exchange membrane in fuel cell applications.     

Factors influencing reverse osmosis rejection of inorganic solutes from aqueous solution

Reverse osmosis (RO) rejection is strongly influenced by the distribution of solute between the membrane and solvent phases. For this reason, we examined the partition coefficients of inorganic compounds between water and cellulose acetate (CA) membranes. Cation and anion partition coefficients were determined by independent analyses. Effects of fixed (negative) membrane charges on CA are clearly apparent at low solute concentrations. The mean cation/anion partition coefficients decrease with the product of the cation and anion valence, and increase with increasing ionic size. Un-ionized inorganic compounds, HgC1₂ and HAuC1₄, are strongly sorbed by CA membranes. All of these observations are consistent with electrostatic theory.Experimental membrane/water partition coefficients are influenced by temperature, pH, and ion-pairing. CA membranes exhibit swelling and shrinkage when exposed to certain aqueous solutions. Swelling and shrinkage influence solute partition and diffusion coefficients, the water content of the membranes, and their RO rejection.The present results provide a comprehensive experimental basis for understanding the mechanism of RO rejection by CA membranes. Moreover, these results can be used to predict RO behavior under a wide variety of experimental conditions. The potential use of reverse osmosis in a variety of wastewater applications is considered in some detail.     

Pt/SiO2 as addition to multilayer SPSU/PTFE composite membrane for fuel cells

A multilayer composite membrane was prepared by reinforcing sulfonated polysulfone (SPSU) with porous polytetrafluoroethylene (PTFE), and adding Pt/SiO₂–Nafion® membranes on both sides of the SPSU/PTFE membrane to self‐humidify and protect the inside membrane. The ex situ Fenton test and open circuit voltage (OCV) accelerated test show that the composite membrane has better stability than the initial membrane because of the protection of the outside Pt/SiO₂–Nafion layers. The composite membrane has similar performance to that of NRE‐212 under the fully humidified condition and better performance than NRE‐212 without humidifying. The self‐humidifying membrane shows great potential for use in low humidifying conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

Cellulose acetate nanocomposite ultrafiltration membranes tailored with hydrous manganese dioxide nanoparticles for water treatment applications

Hydrous manganese dioxide (HMO) nanoparticles incorporated cellulose acetate (CA) composite ultrafiltration (UF) membranes are prepared with the aim of improving the water permeation and BSA contaminant removal. The HMO nanoparticles are synthesized from manganese ion and characterized by FT‐IR, XRD, and FESEM. The effect of variation of HMO on CA membranes is probed using FT‐IR, EDAX, contact angle, SEM, and AFM analysis to demonstrate their chemical functionality, hydrophilicity, and morphology. CA/HMO membranes are showing the enhancement in pure water flux (PWF), water uptake, porosity, hydrophilicity, fouling resistance, BSA rejection, and flux recovery ratio (FRR). CA‐1 membrane displayed higher PWF (143.6 Lm²h^?1), BSA rejection (95.9%), irreversible fouling (93.3%), and FRR (93.3%). Overall results confirmed that the CA/HMO nanocomposite UF membranes overcome the bottlenecks and shows potential for water treatment applications.     

A mussel‐inspired method to fabricate a novel reduced graphene oxide/Bi12O17Cl2 composites membrane for catalytic degradation and oil/water separation

In this study, a novel dopamine modified graphene‐based photocatalytic membrane with Bi₁₂O₁₇Cl₂ inserted was fabricated to modify the commercial cellulose acetate membrane via vacuum filtration method. Results showed the reduced graphene oxide (RGO)/poly(dopamine) (PDA)/Bi₁₂O₁₇Cl₂‐CA photocatalytic composite membrane exhibited 98% removal efficiency for methylene blue (MB) within 100 minutes and 96% removal efficiency for 4‐CP within 160 minutes. Importantly, the photocatalytic composite membrane can simultaneously achieve dye degradation and oil‐water separation in only one device within a short time. And the as‐prepared membrane displayed great antifouling performance and recyclability after 10 cycles. Meanwhile, the membrane showed excellent stability in the agitated water bath or different pH conditions. In summary, the photocatalytic membrane investigated in this study opens new avenue for treatment of wastewater.     

Novel sulfonated poly (ether ether ketone)/silica coated carbon nanotubes high‐performance composite membranes for direct methanol fuel cell

The major risk of using carbon nanotubes (CNTs) to modify proton exchange membranes (PEMs) in fuel cells is possible short‐circuiting due to the excellent electrical conductivity of CNTs. In this article, silica‐coated CNTs (SiO₂@CNTs) were successfully prepared by a simple sol–gel process and then used as a new additive in the preparation of sulfonated poly (ether ether ketone) (SPEEK)‐based composite membranes. The insulated and hydrophilic silica coated on the surface of CNTs not only eliminated the risk of short‐circuiting, but also enhanced the interfacial interaction between CNTs and SPEEK, and hence promoted the homogeneous dispersion of CNTs in the SPEEK matrix. Moreover, compared to the methanol permeability of the pure SPEEK membrane (3.42 × 10^?7 cm² s^?1), the SPEEK/SiO₂@CNT composite membrane with a SiO₂@CNT loading of 5 wt% exhibits almost one order of magnitude decrease of methanol crossover, while the proton conductivity still remained above 10^?2 S cm^?1 at room temperature. The obtained results expose the possibility of SPEEK/SiO₂@CNT membranes to be served as high‐performance PEMs in direct methanol fuel cells. Copyright © 2015 John Wiley & Sons, Ltd.     

Preparation and characterization of cellulose acetate‐coated compound fertilizer with controlled‐release and water‐retention

A novel cellulose acetate‐coated compound fertilizer with controlled‐release and water‐retention (CAFCW) was prepared, which possessed the three‐layer structure. Its core was water‐soluble compound fertilizer granular, the inner coating was cellulose acetate (CA), and the outer coating was poly(acrylic acid‐co‐acrylamide)/unexpanded vermiculite (P(AA‐co‐AM)/UVMT) superabsorbent composite. The effects of the amount of acrylamide, crosslinker, initiator, degree of neutralization of acrylic acid (AA), and unexpanded vermiculite concentration on water absorbency were investigated and optimized. The water absorbency of CAFCW was 72 times its own weight if it was allowed to swell in tap water at room temperature for 90 min. Element analysis and atomic absorption spectrophotometer results showed that the product contained 11% nitrogen, 6% phosphorus (shown by P₂O₅), 9% potassium (shown by K₂O), 1% calcium (shown by CaO), and 0.4% magnesium (shown by MgO). Swelling rate, slow‐release, and water‐retention properties of CAFCW were also investigated. This product with good controlled‐release and water‐retention capacity, being degradable in soil and environmentally friendly, could be especially useful in agricultural and horticultural applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and characterization of polyaniline/silicon dioxide composites and preparation of conductive films

The focus of this study was to synthesize the inherently conductive polymer polyaniline using an optimized process to prepare polyaniline/silicon dioxide (PANI/SiO₂) composites by in situ polymerization and ex situ solution mixing. PANI and PANI/SiO₂ composite films were prepared by drop‐by‐drop and spin coating methods. The electrical conductivities of HCl doped PANI film and PANI/SiO₂ composite films were measured according to the standard four‐point‐probe technique. The composite films exhibited an increase in electrical conductivity over neat PANI. PANI and PANI/SiO₂ composites were also investigated by spectroscopic methods including UV‐Vis, FT‐IR, and Photoluminescence. UV‐Vis and FT‐IR studies showed that SiO₂ particles affect the quinoid units along the polymer backbone and indicate strong interactions between the SiO₂ particles and the quinoidal sites of PANI (doping effect). The photoluminescence properties of PANI and PANI/SiO₂ composites were studied and the PANI/SiO₂ composites showed increased intensity as compared to neat PANI. The increase of conductivity of PANI/SiO₂ composite may be partially due to the doping or impurity effect of SiO₂ where the silicon dioxides compete with chloride ions. The morphology of particles and films were examined by a scanning electron microscope (SEM). SEM measurements indicated that the SiO₂ were well dispersed and isolated in composite films. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation and properties of Nafion/SiO2 composite membrane derived via in situ sol–gel reaction: size controlling and size effects of SiO2 nano‐particles

A novel technique in controlling the size of SiO₂ nano‐particles in the preparation of Nafion/SiO₂ composite membranes via in situ sol–gel method, as well as the effects of nano‐particle size on membrane properties and cell performance, is reported in this paper. Nafion/SiO₂ composite membranes containing SiO₂ nano‐particles with four different diameters (5 ± 0.5, 7 ± 0.5, 10 ± 1, and 15 ± 2 nm) are fabricated by altering the reactant concentrations during in situ sol–gel reaction. Sequentially, size effects of SiO₂ nano‐particles on membrane properties and cell performance are investigated by SEM/EDAX, TEM, TGA, mechanical tensile, and single cell tests, etc. The results suggest that 10 nm is a critical diameter for SiO₂ incorporated into Nafion matrix, exhibiting desirable physico‐chemical properties for operation at elevated temperature and low humidity. At 110°C and 59% RH, the output voltage of the cell equipped with Nafion/SiO₂ (10 nm) obtains an output voltage of 0.625 V at 600 mA/cm², which is 50 mV higher than that of unmodified Nafion. Copyright © 2010 John Wiley & Sons, Ltd.     

MOF Scaffold for a High‐Performance Mixed‐Matrix Membrane

A novel composite membrane consisting of an interconnected MOF scaffold coated with cross‐linked poly(ethylene glycol) (PEG) has been developed. As a result of its unique structure, the membrane shows an exceptional 18‐fold permeability enhancement as compared to pristine PEG membranes, without compromising the selectivity. This performance is unattainable with current mixed‐matrix membranes (MMMs). Our optimized membrane has a permeability of 2700 Barrer with a CO₂/N₂ selectivity of 35, which surpasses the latest Robeson upper bound.     

Effect of preparation variables on morphology and pure water permeation flux through asymmetric cellulose acetate membranes

In this study, cellulose acetate (CA) ultrafiltration (UF) membranes were prepared using the phase inversion method. Effects of CA and polyethylene glycol (PEG) concentrations in the casting solution and coagulation bath temperature (CBT) on morphology of the synthesized membranes were investigated. Based on L₉ orthogonal array of Taguchi experimental design 18 membranes were synthesized (with two replications) and pure water permeation flux through them were measured. It was found out that increasing PEG concentration in the casting solution and CBT, accelerate diffusional exchange rate of solvent 1-methyl-2-pyrrolidone (NMP) and nonsolvent (water) and consequently facilitate formation of macrovoids in the membrane structure. Increasing CA concentration, however, slows down the demixing process. This prevents instantaneous growth of nucleuses in the membrane structure. Hence, a large number of small nucleuses are created and distributed throughout the polymer film and denser membranes are synthesized. Rate of water flux through the synthesized membranes is directly dependent on the size and number of macrovoids in the membrane structure. Thus, maximum value of flux is obtained at the highest levels of PEG concentration and CBT (10 wt.% and 23 °C, respectively) and the lowest level of CA concentration (13.5 wt.%). Analysis of variance (ANOVA) showed that all parameters have significant effects on the response. However, CBT is the less influential factor than CA and PEG concentrations on the response (flux).     

Improvement in gas separation properties of a polymeric membrane through the incorporation of inorganic nano‐particles

The present work tries to introduce a high‐performance nano‐composite membrane by using polydimethylsiloxane (PDMS) as its main polymer matrix to meet some specific requirements in industrial gas separations. Different nano‐composite membranes were synthesized by incorporating various amounts of nano‐sized silica particles into the PDMS matrix. A uniform dispersion of nano‐particles in the host membranes was obtained. The nano‐composite membranes were characterized morphologically by scanning electron microscopy and atomic force microscopy. Separation properties, permeability, and ideal selectivity of C₃H₈, CH₄, and H₂ through the synthesized nano‐composite membranes with different nano‐particle contents (0.5, 1, 1.5, 2, 2.5, and 3 wt%) were investigated at different pressures (2, 3, 4, 5, 6, and 7 atm) and constant temperature (35°C). It was found out that a 2 wt% loading of nano‐particles into the PDMS matrix is optimal to obtain the best separation performance. Afterwards, sorption experiments for the synthesized nano‐composite membranes were carried out, and diffusion coefficients of the gases were calculated based on solution‐diffusion mechanism. Gas permeation and sorption experiments showed an increase in sorption and a decrease in diffusion coefficients of the gases through the nano‐composite membranes by adding nano‐particles into the host polymer matrix. Copyright © 2011 John Wiley & Sons, Ltd.     

Studies on cellulose acetate-carboxylated polysulfone blend ultrafiltration membranes--Part I

Hydrophilic polysulfone ultrafiltration (UF) membranes were prepared from blends of cellulose acetate with carboxylated polysulfone of 0.14 degree of carboxylation. The effects of blend polymer composition on compaction, pure water flux, water content and membrane hydraulic resistance (R_m), have been investigated to evaluate the performance of the membranes. The performance of the blend membranes of various blend polymer compositions were compared with that of membranes prepared from pure cellulose acetate and blends of cellulose acetate and pure polysulfone. The hydrophilic cellulose acetate-carboxylated polysulfone blend UF membranes showed better performance compared to membranes prepared from pure cellulose acetate and blends of cellulose acetate and pure polysulfone.     

Surface redox polymerized SPEEK–MO2–PANI (M = Si, Zr and Ti) composite polyelectrolyte membranes impervious to methanol

We reported sulfonated poly(ether ether ketone) (SPEEK, 61% degree of sulfonation)–metal oxides (MO₂:SiO₂, TiO₂ and ZrO₂)–polyaniline composite membranes. Metal oxides were incorporated into the swelled SPEEK membrane by sol–gel method and cured by thermal treatment. SPEEK–metal oxide membranes surfaces were modified with polyaniline (PANI) by a redox polymerization process. It was observed that water retention capacity of membrane was increased and methanol permeability was reduced due to synergetic effect of metal oxides and surface modification with polyaniline. These composite membranes showed extremely low methanol permeability (1.9–1.3 × 10⁻⁷ cm² s⁻¹), which was lower than till reported values either for SPEEK–metal oxide or SPEEK/PANI membranes. Relatively high selectivity parameter (SP) values at 343 K of these membranes, especially S–SiO₂–PANI and S–TiO₂–PANI, indicated their great advantages over Nafion117 (N117) membrane for targeting on moderate temperature applications due to the synergetic effect of MO₂ and PANI in SPEEK matrix. S–TiO₂–PANI and N117 showed comparable cell performance in direct methanol fuel cell (DMFC).     

A novel composite microsphere as a highly efficient absorbent for oils and organic solvents

A novel composite oil‐absorbent microsphere poly(stearyl methacrylate‐co‐butyl acrylate) (PSB)‐SiO₂ was prepared by introducing hydrophobic nano‐silica Aerosil R812 into the suspension polymerization system of stearyl methacrylate and butyl acrylate and was characterized by Fourier transform infrared and scanning electron microscopy energy‐dispersive spectrometer. PSB‐SiO₂ has a loose network structure and exhibits remarkably fast oil absorption speed in relatively high saturated oil absorbency. Besides, PSB‐SiO₂ has good oil retention and reusability. Moreover, the saturated oil absorbencies of PSB‐SiO₂ toward toluene, gasoline, and diesel over water are roughly equivalent to that in pure oil. Owing to its excellent oil absorption performances, PSB‐SiO₂ will find applications in removing oil spills and organic pollutants over water. Copyright © 2016 John Wiley & Sons, Ltd.     

Temperature‐Modulated Water Filtration Using Microgel‐Functionalized Hollow‐Fiber Membranes

In the present work, we investigate the potential of aqueous polymer microgels in membrane technology, especially for filtration applications. The poly(N‐vinylcaprolactam)‐based microgels exhibit thermoresponsive behavior and were employed to coat hollow‐fiber membranes used for micro‐ and ultrafiltration. We discuss the preparation of microgel‐modified membranes (by “inside‐out” as well as “outside‐in” filtration in dead‐end mode). The clean‐water permeability and stability of these membranes was studied not only as a function of time, but also of temperature. The microgel‐modified membranes exhibit a reversible thermoresponsive behavior whereby both the resistance and the retention increased with decreasing temperature.     

Preparation and characterization of novel PES‐(SiO2‐g‐PMAA) membranes with antifouling and hydrophilic properties for separation of oil‐in‐water emulsions

In the present study, modification of nanoparticles (NPs) was investigated to mitigate aggregation of SiO₂ nanoparticles and improve the polymeric membrane's performance. For this purpose, the surface of SiO₂ nanoparticles was activated with amine groups, and polymethacrylic acid (PMAA) was grafted on the surface of NPs by atom transfer radical polymerization. Modified NPs were characterized by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) tests. Polyethersulfone (PES) membranes were fabricated with both SiO₂ and SiO₂‐g‐PMAA NPs via nonsolvent‐induced phase separation method. The fabricated membranes were characterized regarding their permeability, hydrophilicity, and porosity properties, and their separation efficiency was tested using the synthetic oil‐in‐water emulsion. The surface and cross‐sectional morphologies of membranes were observed by field emission scanning electron microscopy (FESEM). The experimental trials showed that modified NPs dispersed more uniformly in the structure of membranes and hydroxyl groups on the surface of NPs acted more effectively. Modification of NPs enhance the membrane performance in terms of permeate flux, hydrophilicity, and porosity. NPs modification improved the permeate flux about 46%. Oil rejection for all tested membranes was more than 98%, and modification of NPs did not reduce the rejection of membranes. The optimum concentration was obtained as 1 wt.% and 1.5 wt.% for SiO₂ and SiO₂‐g‐PMAA, respectively. Aggregation effect dominated at concentrations beyond the optimum values that decreased the permeate flux, consequently.