Determination of copper at ng levels by in-line preconcentration and flow-injection analysis coupled with flame atomic-absorption spectrometry

Oxine/formaldehyde/resorcinol and oxine/formaldehyde/hydroquinone resins have been synthesized and their physicochemical properties studied. Conditions were optimized for the preconcentration of copper by batch extraction and column chromatography with the resins. A flow-injection analysis (FIA) manifold was constructed for the determination of copper at ng levels by preconcentration on microcolumns containing the resins, stripping, and atomic-absorption spectrometry. For batch preconcentration a pH of about 2.5-3 was optimal whereas in the FIA system a broader pH range (approximately 2-3.5) could be used. Separations of binary mixtures of Cu(II) with Ni(II) or PB(II) at microg/ml level did not show any cross-contamination. In the FIA, a 2 cm long column and 2 ml/min flow-rate were adequate for quantitative uptake of copper; 50 micro1 of 0.1M hydrochloric acid quantitatively eluted the copper.     

Azocalix[4]pyrrole Amberlite XAD-2: New polymeric chelating resins for the extraction, preconcentration and sequential separation of Cu(II), Zn(II) and Cd(II) in natural water samples

Two novel azocalix[4]pyrrole Amberlite XAD-2 polymeric chelating resins were synthesized by covalently linking diazotized Amberlite XAD-2 with calix[4]pyrrole macrocycles. The chelating resins were used for extraction, preconcentration and sequential separation of metal ions such as Cu(II), Zn(II) and Cd(II) by column chromatography prior to their determination by UV/vis spectrophotometry or flame atomic absorption spectrophotometry (FAAS) or inductively coupled plasma atomic emission spectroscopy (ICP-AES). Various parameters such as effect of pH on absorption, concentration of eluting agents, flow rate, total sorption capacity, exchange kinetics, preconcentration factor, distribution coefficient, breakthrough capacity and resin stability, were optimized for effective separation and preconcentration. The resin showed good ability for the separation of metal ions from binary and ternary mixture on the basis of pH of absorption and concentration of eluting agents. The newly synthesized resins showed good potential for trace enrichment of Cu(II), Zn(II) and Cd(II) metal ions, especially for Cu(II), as compared to the earlier reported resins. The synthesized resins were recycled at least 8-10 times without much affecting column sorption capacity. The presented method was successfully applied for determination of Cu(II), Zn(II) and Cd(II) in natural and ground water samples.     

Amberlite XAD-2 functionalized with o-aminophenol: synthesis and applications as extractant for copper(II), cobalt(II), cadmium(II), nickel(II), zinc(II) and lead(II)

A stable chelating resin matrix was synthesized by covalently linking o-aminophenol (o-AP) with the benzene ring of the polystyrene–divinylbenzene resin, Amberlite XAD-2, through a –N=N– group. Elemental analyses, thermogravimetric analysis (TGA) and infrared spectra have characterized the resulting chelating resin. It has been used to preconcentrate Cu²⁺, Cd²⁺, Co²⁺, Ni²⁺, Zn²⁺ and Pb²⁺, prior to their determination by flame atomic absorption spectrometry. The optimum pH values for quantitative sorption of Cu, Cd, Co, Ni, Zn and Pb are 6.2–7.4, 5.6–7.2, 5.6–9.0, 6.0–9.0, 5.7–7.0 and 5.0–6.0, respectively. These metals are desorbed (recovery 91–98%) with 4 mol dm⁻³ HNO₃. The sorption capacity of the resin is 3.37, 3.42, 3.29, 3.24, 2.94 and 3.32 mg of metal g⁻¹ of resin, respectively, for Cu, Cd, Co, Ni, Zn and Pb. The effect of NaF, NaCl, NaNO₃, Na₂SO₄, and Na₃PO₄ on the sorption of these metal ions has been investigated. These electrolytes are tolerable up to 0.01 mol dm⁻³ in case of all the metal ions, except Cl⁻ which is tolerable even up to 0.1 mol dm⁻³ for Zn and 1.0 mol dm⁻³ for Pb. The preconcentration factor for Cu, Cd, Co, Ni, Zn and Pb are 50, 50, 100, 65, 40 and 40 (concentration level 10–25 μg dm⁻³) respectively. Simultaneous enrichment of the six metals is possible. The method has been applied to determine Cu, Cd, Co, Ni, Zn and Pb content in well water samples (RSD≤8%).     

Layer-by-layer self-assembly polytungstogermanate multilayer films and their photocatalytic properties under sunlight irradiation

Seven different types of thio- and/or amine-modified cellulose resin materials were synthesized and their mercury (II) ion adsorption properties determined. All seven resins showed good mercury (II) adsorption capability in the more neutral pH regions. However, the o-benzenedithiol- and o-aminothiophenol-modified cellulosic resins were found to be very effective in removing mercury (II) ions from strongly acidic media. For example, 93.5-100% mercury (II) ion recoveries from very acid aqueous solutions (nitric acid concentration ranged from 0.1 to 2.0 mol/L) were obtained using the o-benzenedithiol-modified resin while recoveries ranged from ca. 50% to 60% for the o-aminothiophenol-modified resin. An adsorption capacity of 23 mg (as Hg atoms) per gram of resin was observed for the o-benzenedithiol-modified cellulose in the presence of 1.0 mol/L nitric acid. This same resin shows very good selectivity for mercury (II) as only ruthenium (II) also somewhat adsorbed onto it out of 14 other metal ions studied (Ag(+), Al(3+), As(3+), Co(2+), Cd(2+), Cr(3+), Cu(2+), Fe(3+), Mn(2+), Ni(2+), Pt(2+), Pb(2+), Ru(2+), and Zn(2+)).     

Synthesis, physical studies and uptake behavior of: copper(II) and lead(II) by Schiff base chelating resins

Two new chelating resins possessing multiple functional groups capable of coordinating with several metal ions are reported. The resins were synthesized by condensing Schiff bases derived from 2-aminophenol, 2-hydroxy-5-chloroaniline and terephthaldehyde with formaldehyde in an alkaline medium. The effects of pH and contact time of the Cu(2+) and Pb(2+) in aqueous solutions on the uptake behavior of the resins were studied. The metal ion uptake behavior of the resins was investigated by the batch method. Both the uptake and the selectivity of the resins towards the investigated metal ions were related to the structure of the resins, type of the metal ion and the uptake conditions. The resins showed maximum uptake capacity for Cu(2+) and Pb(2+) at pH 10. Cu(2+) was seen to undergo preferential adsorption in separate and mixture solutions of Cu(2+) and Pb(2+). Kinetic studies for the resins using Langmiur equation were also performed. The Schiff base monomers and their formaldehyde resins were characterized by elemental analyses, FTIR and (1)H NMR spectroscopy. The thermal stability of the resins was studied using TGA/DTG analysis.     

EFFECT OF THE DEGREE OF DVB CROSSLINKING ON THE METAL ION SPECIFICITY OF POLYACRYLAMIDE-SUPPORTED GLYCINES

Metal ion specificity studies of divinylbenzene (DVB)-crosslinked polyacrylamide-supported glycines in different structural environments were investigated. The effect of the degree of crosslinking on the specific rebinding of the desorbed metal ion was investigated towards Co(II), Ni(II), Cu(II), and Zn(II) ions. The metal ion-desorbed resins showed specificity for the desorbed metal ion and the specificity characteristics increases with an increasing degree of the crosslinking agent. The polymeric ligands and metal complexes were characterized by IR, UV-visible and EPR spectra, and by SEM analysis. The swelling and solvation characteristics of the crosslinked polymers, polymeric ligands and metal complexes, the effect of the pH dependence on metal ion binding and rebinding and the kinetics of metal ion binding and rebinding were also followed. The complexation resulted in the downfield shift of the carboxylate peak in the IR spectra. The EPR parameters are in agreement with a distorted tetragonal geometry. The Cu(II) ion-desorbed resins selectively rebinds Cu(II) ions from a mixture of Cu(II) and Co(II) and Cu(II) and Ni(II) ions. The resin could be regenerated several times without loss of capacity and effective for the specific and selective rebinding of Cu(II) ions.     

Preconcentration of metal ions on porphyrin-modified sorbents as pretreatment step in AAS determination

The preconcentration of some divalent metal ions by complexation with carboxyphenylporphyrin (TCPP) and retention on conventional anion-exchange resins and a non-ionic sorbent was examined. Two different procedures--ligand in solution or immobilised on the solid sorbents--were evaluated as a function of pH. The selectivity order for metal ions on the TCPP-loaded resin Amberlite IRA-904 was established as: Pb(II)>Ni(II)>Cu(II)>Cd(II)>Mg(II).     

A new chelating sorbent for metal ion extraction under high saline conditions

A new chelating polymeric sorbent was developed by functionalizing Amberlite XAD-16 with 1,3-dimethyl-3-aminopropan-1-ol via a simple condensation mechanism. The newly developed chelating matrix offered a high resin capacity and faster sorption kinetics for the metal ions such as Mn(II), Pb(II), Ni(II), Co(II), Cu(II), Cd(II) and Zn(II). Various physio-chemical parameters like pH-effect, kinetics, eluant volume and flow rate, sample breakthrough volume, matrix interference effect on the metal ion sorption have been studied. The optimum pH range for the sorption of the above mentioned metal ions were 6.0–7.5, 6.0–7.0, 8.0–8.5, 7.0–7.5, 6.5–7.5, 7.5–8.5 and 6.5–7.0, respectively. The resin capacities for Mn(II), Pb(II), Ni(II), Co(II), Cu(II), Cd(II) and Zn(II) were found to be 0.62, 0.23, 0.55, 0.27, 0.46, 0.21 and 0.25 mmol g⁻¹ of the resin, respectively. The lower limit of detection was 10 ng ml⁻¹ for Cd(II), 40 ng ml⁻¹ for Mn(II) and Zn(II), 32 ng ml⁻¹ for Ni(II), 25 ng ml⁻¹ for Cu(II) and Co(II) and 20 ng ml⁻¹ for Pb(II). A high preconcentration value of 300 in the case of Mn(II), Co(II), Ni(II), Cu(II),Cd(II) and a value of 500 and 250 for Pb(II) and Zn(II), respectively, were achieved. A recovery of >98% was obtained for all the metal ions with 4 M HCl as eluting agent except in the case of Cu(II) where in 6 M HCl was necessary. The chelating polymer showed low sorption behavior to alkali and alkaline earth metals and also to various inorganic anionic species present in saline matrix. The method was applied for metal ion determination from water samples like seawater, well water and tap water and also from green leafy vegetable, from certified multivitamin tablets and steel samples.     

Solid phase extractive preconcentration of trace metals using p-tert-butylcalix[4]arene-1,2-crown-4-anchored chloromethylated polymeric resin beads

5,11,17,23-Tetrakis(1,1-dimethylethyl)-25,26-dihydroxy-27,28-crown-4-calix[4]arene in the cone conformation was synthesized. This p-tert-butylcalix[4]arene-1,2-crown-4 compound was then anchored with Merrifield chloromethylated resin beads. The modified polymeric resin was characterized by ¹H NMR, FT-IR and elemental analysis and used successfully for the separation and preconcentration of Cu(II), Cd(II), Co(II), Ni(II) and Zn(II) prior to their determination by FAAS. Effective extraction conditions were optimized in both batch and column methods. The resin exhibits good separating ability with maximum between pH 6.0-7.0 for Cu(II), pH 6.0 for Cd(II), pH 5.0 for Co(II), pH 4.0-4.5 for Ni(II), and pH 4.5 for Zn(II). The elution studies were carried out with 0.5 mol L⁻¹ HCl for Cu(II), Co(II) and Co(II), 1.0 mol L⁻¹ HCl for Cd(II) and Zn(II). The sorption capacity, preconcentration factor and distribution coefficient of each metal ion were determined. The detection limits were 1.10, 1.25, 1.83, 1.68 and 2.01 μg L⁻¹ for Cu(II), Cd(II), Co(II), Ni(II) and Zn(II). The influence of several ions on the resin performance was also investigated. The validity of the proposed method was checked for these metal ions in NIST standard reference material 2709 (San Joaquin Soil) and 2711 (Montana Soil).     

Preparation and metal-adsorption properties of polystyrene resins functionalized with multidentate ligands having nitrogen and sulfur donor sets

N-Mercaptoethylated derivatives of macroporous polystyrene resins functionalized with diethylenetriamine or pyridylamines have been synthesized. The resin with higher sulfur content reveals better selectivity toward ‘soft’ metal ions. Concentration of Ag(I) and Hg(II) has been examined by the column containing the present chelating resins.     

Nano-iron oxide-encapsulated chitosan microspheres as novel adsorbent for removal of Ni (II) ions from aqueous solution

The present study investigates the utility of composite beads of nano-particles of iron oxide and chitosan for removing Ni (II) ions from aqueous solution by batch and column adsorption techniques. In the batch mode experiment, the influence of pH, concentration, adsorbent dose, temperature, column mode, bed height, flow rate and initial concentration were studied on the adsorption profiles of nickel ions. The maximum uptake of Ni (II) ions was obtained at pH 4.0 in 30 min at room temperature.     

Preconcentration of trace metals on Amberlite XAD-4 resin coated with dithiocarbamates and determination by inductively coupled plasma-atomic emission spectrometry in saline matrices

Preconcentration of Cd(II), Cu(II), Mn(II), Ni(II), Pb(II) and Zn(II) in saline matrices on Amberlite XAD-4 resins coated with ammonium pyrrolidine dithiocarbamate (APDC) and piperidine dithiocarbamate (pipDTC) and subsequent determination by inductively coupled plasma atomic emission spectrometry were studied. Parameters such as effect of pH, effect of HNO(3) concentration on elution of metals from resin were studied. The results show that Amberlite XAD-4 coated with APDC was more efficient in the recovery of metal ions compared with Amberlite XAD-4 coated with pipDTC, in the concentration range of 0.1-200 mug l(-1), for 1 g of Amberlite XAD-4 coated resin. The detection limits for Cd(II), Cu(II), Mn(II), Ni(II), Pb(II), Zn(II) are 0.1, 0.4, 0.3, 0.4, 0.6, 0.5 mug l(-1), respectively, for resin coated with APDC and 0.7, 1.0, 0.8, 0.9, 1.7 and 1.2 mug l(-1) for resin coated with pipDTC. The effect of diverse ions on the determination of aforesaid metals was studied. The method was applied for the determination of trace metal ions in artificial sea water and natural water samples. The results were compared with extraction AAS method.     

Preconcentration of trace metal ions by combined complexation-anion exchange : Part 2. Cobalt,zinc, cadmium and lead with 8-hydroxyquinoline-5-sulfonic acid [1]

The ligand, 8-hydroxyquinoline-5-sulfonic acid, forms anionic complexes with cobalt(II), zinc(II), cadmium(II), and lead(II), each resulting complex showing a high affinity for anion-exchange resins. The effect of pH, ligand/metal ratio, volume, and concentration on percent retention of the anionic complexes by an anion-exchange resin are reported. At optimum conditions, all four metals are quantitatively retained by the column. Zinc, cadmium and lead(II) ions are completely eluted with 11 ml or less of 2 M HN0₃; cobalt(II) is totally removed by 12 M HCl and 2 M HNO₃. Concentration enhancements of 100-fold are easily achieved. All four anionic complexes can be left on the column for 7 days and still be quantitatively (99%) recovered. A ligand-loaded resin column can also remove all four metals quantitatively. Distribution coefficients for the metal complexes and their ligand/metal ratios were determined by using batch methods that may also serve as the isolation procedure.     

Determination of Cu,Ni, and Zn in fuel ethanol by FAAS after enrichment in column packed with 2-aminothiazole-modified silica gel

This work describes the synthesis and characterization of 2-aminothiazole-modified silica gel (SiAT), as well as its application for preconcentration (in batch and column technique) of Cu(II), Ni(II) and Zn(II) in ethanol medium. The adsorption capacities of SiAT determined for each metal ion were (mmol g(-1)): Cu(II)=1.20, Ni(II)=1.10 and Zn(II)=0.90. In addition, results obtained in flow experiments, showed a recovery of ca. 100% of the metal ions adsorbed in a column packed with 500 mg of SiAT. The eluent was 2.0 mol L(-1) HCl. The sorption-desorption of the studied metal ions made possible the development of a preconcentration method for metal ions at trace level in fuel ethanol using flame AAS for their quantification.     

Development of column-pretreatment chelating resins for matrix elimination/multi-element determination by inductively coupled plasma-mass spectrometry

Chelating resins, two kinds of iminodiacetate derivatives (IDA) of cross-linked chitosan (CCS) were synthesized and investigated for adsorption capacity, matrix elimination and collection/concentration of analytes by a column pretreatment in a multi-element ICP-MS determination method. The adsorption behavior of 54 elements at the 10 ng ml(-1) level on chitosan derivatives in a packed mini-column was systematically examined. Almost 30 kinds of metal ions were recovered quantitatively at pH 5 with CCS-HP/IDA (cross-linked chitosan possessing N-2-hydroxypropyl iminodiacetic acid groups) column. Compared with available chitosan-iminodiacetate resin, CHITOPEARL CI-03, the recovery of the metal ions such as Cu, Pb and La is satisfactory with CCS-IDA (cross-linked chitosan possessing N,N-iminodiacetic acid groups) and CCS-HP/IDA using 2 M nitric acid as an eluent, which may be attributed to the difference of cross-linking and macroporous structure. Compared with Chelex-100, the adsorption efficiency is in the order: Chelex-100 > CCS-IDA > CCS-HP/IDA, especially in the chelating ability for alkaline earth metals. The resin with a longer spacer (CCS-HP/IDA) showed higher adsorption selectivity between heavy metal ions and alkaline earth metals at pH < 7. The separation efficiency of the major matrix cations in seawater (Na. K, Mg, Ca) has also been investigated, and matrix interference was negligible even in a seawater sample at pH 5 with CCS-HP/IDA. The recoveries of Mn at pH 5 with CCS-HP/IDA or Chelex-100 were almost 100%. However, those of Mg with each resin were 4 or 98%, respectively. The adsorption capacities of synthesized CCS-HP/IDA for Cu(II), Pb(II) and La(III) were 0.90, 0.65 and 0.34 mmol g(-1), respectively. Therefore, the chelating chitosan resins developed are applicable to the pretreatment of trace amounts of elements in various kinds of water samples.     

Synthesis and analytical properties of a chelating resin functionalised with bis-(N,N'-salicylidene)1,3-propanediamine ligands

A polystyrenedivinylbenzene-based macroreticular resin was functionalised with bis-(N,N'-salicylidene)1,3-propanediamine ligands and its analytical properties have been investigated. The pH dependence of metal resin chelation has been determined for Cu(II), Ni(II), Co(II), Zn(II), Fe(II), Mn(II), Pb(II), Cd(II) and Cr(III). Trace amounts of these metal ions were quantitatively retained on the resin at neutral pH and easily recovered by elution with 1 N hydrochloric acid. The resin exhibits good chemical stability and fast equilibration with the metal ion making it useful for rapid concentration of trace amounts of metal ions on the resin columns.     

The efficacy of nitrosonaphthol functionalized XAD-16 resin for the preconcentration/sorption of Ni(II) and Cu(II) ions

Amberlite XAD-16 resin has been functionalized using nitrosonaphthol as a ligand and characterized employing elemental, thermogravimetric analysis and FT-IR spectroscopy. The sorption of Ni(II) and Cu(II) ions onto this functionalized resin is investigated and optimized with respect to the sorptive medium (pH), shaking speed and equilibration time between liquid and solid phases. The monitoring of the influence of diverse ions on the sorption of metal ions has revealed that phosphate, bicarbonate and citrate reduce the sorption up to 10–14%. The sorption data followed Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherms. The Freundlich parameters computed are 1/n = 0.56 ± 0.03 and 0.49 ± 0.05, A = 9.54 ± 1.5 and 6.0 ± 0.5 mmol g⁻¹ for Ni(II) and Cu(II) ions, respectively. D–R isotherm yields the values of X_m = 0.87 ± 0.07 and 0.35 ± 0.05 mmol g⁻¹ and of E = 9.5 ± 0.23 and 12.3 ± 0.6 kJ mol⁻¹ for Ni(II) and Cu(II) ions, respectively. Langmuir characteristic constants estimated are Q = 0.082 ± 0.005 and 0.063 ± 0.003 mmol g⁻¹, b = (4.7 ± 0.2) × 10⁴ and (7.31 ± 0.11) × 10⁴ l mol⁻¹ for Ni(II) and Cu(II) ions, respectively. The variation of sorption with temperature gives thermodynamic quantities of ΔH = −58.9 ± 0.12 and −40.38 ± 0.11 kJ mol⁻¹, ΔS = −183 ± 10 and −130 ± 8 J mol⁻¹ K⁻¹ and ΔG = −4.4 ± 0.09 and −2.06 ± 0.08 kJ mol⁻¹ at 298 K for Ni(II) and Cu(II) ions, respectively. Using kinetic equations, values of intraparticle transport and of first order rate constant have been computed for both the metal ions. The sorption procedure is utilized to preconcentrate these ions prior to their determination in tea, vegetable oil, hydrogenated oil (ghee) and palm oil by atomic absorption spectrometry using direct and standard addition methods.     

Synthesis and properties of a chelating resin containing triazolethiol groups

A macroreticular poly(acrylic acid)-based resin with triazolethiol as the functional group has been synthesized. The stability of the resin in acidic media and the behaviour in sorption and desorption of various metal ions have been investigated and compared with those of the acylthiosemicarbazide resin which is an intermediate in synthesis of the triazolethiol resin. Both resins show high affinity for copper(II) silver, cadmium and mercury(II), and high selectivity for silver and mercury(II) at low pH (1–2), and even at pH 7 if EDTA is present. The triazolethiol resin sorbs metal ions faster than the acylthiosemicarbazide resin does and sorbs mercury(II) from high concentrations of acids and neutral salt solutions. This resin has been applied to the concentration of silver and mercury(II) from sea-water samples by column operation.     

Synthesis and application of modified poly (styrene‐alt‐maleic anhydride) networks as a nano chelating resin for uptake of heavy metal ions

A chelating resin based on modified poly (styrene‐alt‐maleic anhydride) with 3‐aminobenzoic acid was synthesized. This modified resin was further reacted by 1,2‐diaminoethane or 1,3‐diaminopropane in the presence of ultrasonic irradiation to prepare tridimensional chelating resin for the removal of heavy metal ions from aqueous solutions. The adsorption behavior of Fe(II), Cu(II), Zn(II) and Pb(II) ions was investigated by synthesized chelating resins in various pH. Among the synthesized resins, CSMA‐AB1 and CSMA‐AB2 demonstrated a high affinity for the selected metal ions compared to SMA‐AB, and the order of removal percentage changes as follow: Fe(II) > Cu(II) > Zn(II) > Pb(II). The adsorption of all metal ions in acidic medium was moderate, and it was favored at the pH value of 6 and 7. Also, the prepared resins were examined for removal of metal ions from industrial wastewater and were shown to have a very efficient adsorption in the case of Cu(II), Fe(II) and Pb(II); however, the adsorption of Zn(II) was lower than others. The resin was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction analysis and thermogravimetric analysis/derivative thermogravimetry. Copyright © 2012 John Wiley & Sons, Ltd.     

A new chelating resin for preconcentration and determination of Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) by flame atomic absorption spectrometry

A new polychelatogen, AXAD-16-1,2-diphenylethanolamine, was developed by chemically modifying Amberlite XAD-16 with 1,2-diphenylethanolamine to produce an effective metal-chelating functionality for the preconcentration of Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) and their determination by flame atomic absorption spectrometry. Various physiochemical parameters that influence the quantitative preconcentration and recovery of metal were optimized by both static and dynamic techniques. The resin showed superior extraction efficiency with high-metal loading capacity values of 0.73, 0.80, 0.77, 0.87, 0.74, and 0.81 mmol/g for Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II), respectively. The system also showed rapid metal-ion extraction and stripping, with complete saturation in the sorbent phase within 15 min for all the metal ions. The optimum condition for effective metal-ion extraction was found to be a neutral pH, which is a great advantage in the preconcentration of trace metal ions from natural water samples without any chemical pretreatment of the sample. The resin also demonstrated exclusive ion selectivity toward targeted metal ions by showing greater resistivity to various complexing species and more common metal ions during analyte concentration, which ultimately led to high preconcentration factors of 700 for Cu(II); 600 for Mn(II), Ni(II), and Zn(II); and 500 for Cd(II) and Pb(II), arising from a larger sample breakthrough volume. The lower limits of metal-ion detection were 7 ng/mL for Mn(II) and Ni(II); 5 ng/mL for Cu(II), Zn(II), and Cd(II), and 10 ng/mL for Pb(II). The developed resin was successful in preconcentrating metal ions from synthetic and real water samples, multivitamin-multimineral tablets, and curry leaves (Murraya koenigii) with relative standard deviations of < or = 3.0% for all analytical measurements, which demonstrated its practical utility.