基于飞秒光频梳的压电陶瓷闭环位移控制系统

利用飞秒光频梳、外腔可调谐半导体激光器和法布里-珀罗干涉仪建立了一套压电陶瓷亚纳米级闭环位移控制系统. 将可调谐半导体激光器锁定至光频梳, 通过精确调谐光频梳的重复频率, 实现了半导体激光器在其工作频率范围内的精密调谐. 利用Pound-Drever-Hall锁定技术将带有压电陶瓷的法布里-珀罗腔锁定至半导体激光器, 进而通过频率发生系统控制压电陶瓷产生亚纳米级分辨率的位移. 实验研究发现锁定至光频梳后可调谐半导体激光器1 s的Allan标准偏差为1.68×10^-12, 将其在30.9496 GHz范围内进行连续闭环调谐, 可获得压电陶瓷的位移行程约为4.8 μm; 以3.75 Hz的步长扫描光频梳的重复频率, 实现了压电陶瓷的450 pm闭环位移分辨率并测定了压电陶瓷的磁滞特性曲线. 该系统不存在非线性测量误差, 且激光频率及压电陶瓷位移均溯源至铷钟频率源. 关键词： 光频梳 压电陶瓷 法布里-珀罗腔 可调谐半导体激光器     

A self-consistent model for a SOA-based fiber ring laser including the mode-locked pulse properties

In this paper, we present a self-consistent model of an optically mode-locked semiconductor fiber ring laser. The fiber laser uses a semiconductor optical amplifier (SOA) as the gain medium, while mode-locking is achieved by its gain modulation, via an external optical pulsed signal. We solved the model analytically developing a novel technique, where we have assumed double saturation of the SOA by both the mode-locked and the externally introduced pulsed signal. The study revealed the locus of the laser parameters to achieve mode-locking. In particular, it was found that SOA gain and energy of the externally introduced signal are two critical parameters that must simultaneously set properly for exact mode-locking. Another outcome of our analysis is that the study of the chirp parameter should be carried out keeping the nonlinear terms of the SOA gain. We have also investigated a slightly detuning regime of operation that revealed a fast change of the mode-locking process.     

北京自由电子激光器外注入实验系统设计研究

北京自由电子激光器(BFEL)是一台工作于中红外区Compton型FEL振荡器。本文结合BFEL装置,设计了一套完整的激光外注入光路,利用声光调QCO_2激光器产生的10.6μm激光做激励源注入到BFEL光腔中,以缩短振荡建立时间,提高BFEL输出能量,改善输出激光的相干性。模拟计算结果是:当BFEL光腔中的外注入光强为自发辐射强度的10~5倍时,可使饱和振荡建立时间缩短35％,输出能量提高2倍。     

Experimental and theoretical studies of a high repetition rate fiber laser, mode-locked by external optical modulation

An experimental and theoretical study of a high repetition rate laser source operating on a novel mode-locking technique is presented. This technique relies on the fast saturation and recovery of a semiconductor optical amplifier induced by an external optical pulse and has been used to obtain 4.3 ps pulses at 20 GHz. A complete mathematical model of the fiber ring laser is presented describing the mode-locking process in the laser oscillator and providing solutions for the steady-state mode-locked pulse profile. The critical parameters of the system are defined and analyzed and their impact on the formation of the mode-locked pulses is examined. The comparison between the theoretical results and the experimental data reveals very good agreement and has allowed the optimization of the performance of the system in terms of its critical parameters.     

Cavity waveguide-output laser

We propose for the first time a laser configuration which couples the cavity standing wave field directly with an optical fibre or optical fibre taper using its polished face as an output coupling mirror. A method for direct, active and paraxial launching of laser emission into an optical fibre, adaptable for various laser active media, has been achieved on this basis. Some of the important parameters of this laser are expressed in analytical form. Experimental verification of the proposed idea has been conducted on the basis of a dye laser. Excellent intensity distribution has been obtained beyond the optical fibre output. Launching efficiency exceeding 80% has been predicted and measured experimentally.     

Multi-state optical flip-flop memory based on ring lasers coupled through the same gain medium

We investigate a system consisting of multiple ring lasers coupled by a single gain medium. All the ring lasers share a common feedback arm. The output power of an individual laser shows periodic oscillations as a function of time. The periodicity of the oscillation is determined by the ratio of the roundtrip times of the feedback arm and the ring cavity. In the case that two of such ring lasers are coupled, either their oscillation periodicities are synchronized, or the system is bi-stable. In the latter operation regime, the system can act as an optical flip-flop memory whose state be switched by injection of external light. The concept can be extended to multi-state operations; an eight-state optical flip-flop memory is experimentally demonstrated.     

Dynamic control of the operation regimes of a mode-locked fiber laser based on intracavity polarizing fibers: experimental and theoretical validation

An intracavity polarizing fiber is proposed to control the emission regime of a passively mode-locked fiber laser. Stable operation in self-starting high and low dispersion soliton mode-locking and 100 GHz multiwavelength regimes is demonstrated through numerical simulations and experimental validation. Mode-locking stability is ensured by a saturable absorber in the ring cavity. The effective selection of operation regime is dynamically carried out by controlling the intracavity polarization state.     

Periodic locking of chaos in semiconductor lasers with optical feedback

We show how a chaotic system can be locked to emit a periodic waveform belonging to its chaotic attractor. We numerically demonstrate our idea in a system composed of a semiconductor laser driven to chaos by optical feedback from an external cavity. The clue is the injection of an appropriate periodic signal that modulates the phase and amplitude of the intra-cavity radiation, a chaotic analogy of conventional mode-locking. The result is a time process that manifests a chaotic signature embedded in a long-scale periodic train.     

Different operation states of soliton pulses in an erbium-doped fibre ring laser

We report on the experimental observation of soliton pulses in an erbium doped fibre ring laser. The passive mode-locking is achieved using the nonlinear polarization rotation technique. By adjusting the pump power and the intracavity polarization controllers, a normal soliton, a stable 8th harmonic mode-locked pulse and a noise-like pulse have been observed in our laser. The experimental results revealed that the noise-like pulse is not suitable for the optical telecommunication, and in order to obtain the stable harmonic mode-locked soliton, a strong unstable CW laser field is necessary to mediate global soliton interaction. The formation mechanism of the harmonic mode-locked pulse has also been analysed.     

基于非线性偏振旋转锁模的高功率光子晶体光纤飞秒激光振荡器

为了探索大模场面积光子晶体光纤锁模激光器在全正色散锁模域内的耗散孤子锁模机理, 以获得更大的单脉冲能量和更高的峰值功率, 本文搭建了以掺镱大模场面积光子晶体光纤作为增益介质的耗散孤子锁模激光器. 激光器使用环形腔结构, 利用非线性偏振旋转以及滤光片提供的耗散作用实现了稳定的锁模运转. 实验中, 从激光器振荡级直接获得了平均功率10 W, 重复频率49.09 MHz(对应202 nJ的单脉冲能量), 脉冲宽度为1.03 ps的稳定锁模脉冲输出, 经过腔外色散补偿得到的脉冲宽度为95.5 fs.     

Quasi-monolithic ring resonator for efficient frequency doubling of an external cavity diode laser

A quasi-monolithic second-harmonic-generation ring resonator assembled with miniaturized components is presented. The ring contains a 10-mm-long bulk periodically poled lithium niobate crystal for second-harmonic generation, four plane mirrors and two gradient-index lenses. All parts are mounted on a glass substrate with an overall size of 19.5 mm×8.5 mm×4 mm. As pump source a broad-area laser diode operated in an external resonator with Littrow arrangement is utilized. This external cavity diode laser provides near diffraction limited, narrow-bandwidth emission with an optical output power of 450 mW at a wavelength of 976 nm. Locking of the diode laser emission to the resonance frequency of the ring cavity was achieved by an optical self-injection locking technique. With this setup more than 126 mW of diffraction-limited blue light at 488 nm could be generated. The opto–optical conversion efficiency was 28% and a wall plug efficiency better than 5.5% could be achieved.     

Characterization of the train-average time-frequency parameters inherent in the low-power picosecond optical pulses generated by the actively mode-locked semiconductor laser with an external single-mode fiber cavity

The specific approach to characterizing the train-average parameters of low-power picosecond optical pulses with the frequency chirp, arranged in high-repetition-frequency trains, in both time and frequency domains is elaborated for the important case when the semiconductor laser is matched by an external single-mode fiber cavity and operates in the active mode-locking regime. This approach involves the joint Wigner time-frequency distributions, which can be created for those pulses due to exploitation of a novel interferometric technique. Practically, the InGaAsP/InP-heterolaser generating at the wavelength 1320 nm was used during the experiments carried out and an opportunity of reconstructing the corresponding joint Wigner time-frequency distributions was successfully demonstrated.     

Polarization switching in a quasi-isotropic microchip Nd:YAG laser induced by optical feedback

This paper demonstrates the influence of external optical feedback on the polarization state of longitudinal modes in quasi-isotropic microchip Nd:YAG lasers. Under optical feedback, the polarization state of longitudinal modes in quasi-isotropic lasers relies strongly on the intracavity anisotropy loss and mode competition. When the intracavity anisotropy loss is small, external optical feedback can cause polarization switching and strong mode competition between two orthogonal linearly polarized eigenstates of one laser longitudinal mode, which leads to the distortion of laser intensity modulation waveform. The polarization switching is independent of the initial external cavity length. By increasing the intracavity anisotropy loss, one polarization eigenstate can be suppressed and the laser works in single-polarization state. A theoretical analysis based on the compound cavity model is presented, which is in good agreement with the experimental results. The results offer guidance to the development of laser feedback interferometers.     

Generation of high order multi-bound solitons and propagation in optical fibers

We demonstrate experimental generation of multi-bound solitons of up to sextuple in an active FM mode-locked fiber ring laser operating under power saturation in the locking state. The ring laser consists of two booster optical amplifiers operating in saturation regime, an electro-optic phase modulator driven by a sinusoidal electrical wave and a length of dispersive fiber. The periodic phase modulation generates phase chirp of the generated lightwaves in the ring laser. The chirped phase state plays an important role in the phase matching condition for mode-locking as well as the stabilization and the determination of the bound states of multi-solitons. The formation of such high order multi-bound solitons is explained based on the chirping of the phase and the behavior of the optical pulse sequence in the near field region of the dispersive fiber. The propagation of these multi-bound solitons through single mode optical fibers is observed. Experimental and simulation results of bound solitons have been shown to follow similar trends.The propagation of these multi-bound solitons through single mode optical fibers is described. Their mutual interaction through such quadratic phase media shows the influence of the quadratic phase property on the differential phase of individual solitons of the bound group. Simulated results confirm the evolution of the bound solitons over dispersive single mode optical fibers.     

Controlling spontaneous emission and threshold-less laser oscillation with optical microcavities

We describe the alteration of spontaneous emission of materials in optical microcavities having dimensions on the order of the emitted wavelength. Particular attention is paid to one-dimensional optical confinement structures with pairs of planar reflectors (planar microcavities). The presence of the cavity causes great modifications in the emission spectrum and spatial emission intensity distribution accompanied by changes in the spontaneous emission lifetime. Experimental results are shown for planar microcavities containing GaAs quantum wells or organic dye-embedded Langmuir-Brodgett films as light emitting layers. Also discussed are the laser oscillation properties of microcavities. A remarkable increase in the spontaneous emission coupling into the laser oscillation mode is expected in microcavity lasers. A rate equation analysis shows that increasing the coupling of spontaneous emission into the cavity mode causes the disappearance of the lasing threshold in the input-output curve. Experimentally verification is presented using planar optical microcavities confining an organic dye solution. The coupling ratio of spontaneous emission into a laser mode increases to be as large as 0.2 for a cavity having a half wavelength distance between a pair of mirrors. At this point, the threshold becomes quite fuzzy. Differences between the spontaneous emission dominant regime and the stimulated emission dominant regime are examined with emission spectra and emission lifetime analyses.     

All-normal-dispersion Yb-doped mode-locked fibre laser and its stability analysis

We experimentally demonstrate an all-normal-dispersion Yb-doped mode-locked fibre laser with no intentional spectral filter inserted.Pulses with 1.1 nJ pulse energy at a repetition rate of 20.4 MHz are achieved.A theoretical model of the fibre laser is derived,whose coefficients are explicitly dependent on the orientations of the wave plates and the polarizer.Based on the model,stability diagrams of both the mode-locking and the continuous wave regimes of the laser are presented.The influence of group-velocity dispersion (GVD) and cavity length on the stability of mode-locking is also discussed.     

高能量掺Yb偏振型大模场面积光子晶体光纤孤子锁模飞秒激光器

实验研究了基于掺Yb偏振型大模场面积光子晶体光纤的孤子锁模激光器,获得了高脉冲能量的飞秒激光输出. 激光器基于线形腔结构,利用光栅对补偿腔内色散,并通过半导体可饱和吸收镜实现锁模的自启动. 实验中从振荡级直接获得了平均功率为700mW, 重复频率为47.3MHz(对应于14.8 nJ的单脉冲能量),脉冲宽度为518 fs的稳定锁模脉冲输出. 与普通孤子锁模飞秒光纤激光器相比,输出的单脉冲能量提高了两个数量级. 关键词： 光子晶体光纤 飞秒 光纤激光器 孤子锁模     

Multimode laser emission from dye-doped hollow polymer optical fibre

Well-resolved multimode laser emission was observed for the first time from a freestanding microring cavity based on Rhodamine B dye-doped hollow polymer optical fibre by transverse pumping. Fibres with different diameters such as 180, 460, 640 and 800 μm were fabricated from a dye-doped hollow polymer preform. A blueshift in the mode structure was observed with decrease in fibre diameter leading to wide range tunability of the laser emission.     

All optical clock division and multiplication by injection mode-locked laser based on SOA

Optical clock division and multiplication were realized with an injection mode-locked fiber ring laser based on semiconductor optical amplifier SOA owing to the relatively long recovery time of carriers in SOA and the rational harmonic mode-locking. Second frequency division and 1.5th frequency multiplication of 10 GHz, second and th frequency division of 20 GHz optical pulse trains were realized, respectively, in the experiment.     

二极管泵浦自启动附加脉冲锁模Nd:YLF激光器

实现了激光二极管泵浦Nd:YLF激光器的自启动附加脉冲锁模,工作波长1053um,得到2.8ps的超短脉冲,重复频率130MHz,有效输出功率70mW.