Headspace solid-phase microextraction with novel sol–gel permethylated-β-cyclodextrin/hydroxyl-termination silicone oil fiber for determination of polybrominated diphenyl ethers by gas chromatography–mass spectrometry in soil

A simple, sensitive, and accurate method for determination of polybrominated diphenyl ethers (PBDEs) in soil has been developed based on headspace solid-phase microextraction (HS-SPME) followed by gas chromatography–mass spectrometry (GC–MS). Permethylated-β-cyclodextrin/hydroxyl-termination silicone oil (PM-β-CD/OH-TSO) fiber was first prepared by sol–gel technology and employed in SPME procedure. By exploiting the superiorities of sol–gel coating technique and the advantages of the high hydrophobic doughnut-shaped cavity of PM-β-CD, the novel fiber showed desirable operational stability and extraction ability. After optimization on extraction conditions like water addition, extraction temperature, extraction time, salts effect, and solvents addition, the method was validated in soil samples, achieving good linearity (r > 0.999), precision (R.S.D. < 10%), accuracy (recovery > 78%), and detection limits (S/N = 3) raging from 13.0 to 78.3 pg/g.     

Sequential injection analysis (SIA)-chemiluminescence determination of indomethacin using tris[(2,2'-bipyridyl)]ruthenium(III) as reagent and its application to semisolid pharmaceutical dosage forms

Automated sequential injection (SIA) method for chemiluminescence (CL) determination of nonsteroidal anti-inflammatory drug indomethacin (I) was devised. The CL radiation was emitted in the reaction of I (dissolved in aqueous 50% v/v ethanol) with intermediate reagent tris(2,2′-bipyridyl)ruthenium(III) (Ru(bipy)₃³⁺) in the presence of acetate. The Ru(bipy)₃³⁺ was generated on-line in the SIA system by the oxidation of 0.5 mM tris(2,2′-bipyridyl)ruthenium(II) (Ru(bipy)₃²⁺) with Ce(IV) ammonium sulphate in diluted sulphuric acid. The optimum sequence, concentrations, and aspirated volumes of reactant zones were: 15 mM Ce(IV) in 50 mM sulphuric acid 41 μL, 0.5 mM Ru(bipy)₃²⁺ 30 μL, 0.4 M Na acetate 16 μL and I sample 15 μL; the flow rates were 60 μL s⁻¹ for the aspiration into the holding coil and 100 μL s⁻¹ for detection. Calibration curve relating the intensity of CL (peak height of the transient CL signal) to concentration of I was curvilinear (second order polynomial) for 0.1–50 μM I (r = 0.9997; n = 9) with rectilinear section in the range 0.1–10 μM I (r = 0.9995; n = 5). The limit of detection (3σ) was 0.05 μM I. Repeatability of peak heights (R.S.D., n = 10) ranged between 2.4% (0.5 μM I) and 2.0% (7 μM I). Sample throughput was 180 h⁻¹. The method was applied to determination of 1 to 5% of I in semisolid dosage forms (gels and ointments). The results compared well with those of UV spectrophotometric method.     

Monoclonal antibody-based ELISA for the quantification of nitrofuran metabolite 3-amino-2-oxazolidinone in tissues using a simplified sample preparation

A sensitive and specific monoclonal ELISA for the determination of tissue bound furazolidone metabolite 3-amino-2-oxazolidinone (AOZ) is described. The procedure enables the detection of AOZ in matrix supernatant after homogenisation, protease treatment, acid hydrolysis and derivatisation of AOZ released from the tissue by o-nitrobenzaldehyde. The formed p-nitrophenyl 3-amino-2-oxazolidinone (NPAOZ) is determined by ELISA calibrated with matrix-matched standards in the concentration range of 0.05–5.0 μg I⁻¹. The assay was validated according to criteria set down by Commission Decision 2002/657/EC for the performance and validation of analytical methods for chemical residues. Detection capability, set on the basis of acceptance of no false negative results, was 0.4 μg kg⁻¹ for shrimp, poultry, beef and pork muscle. This sensitivity approaches the established confirmatory LC–MS/MS able to quantify tissue-bound AOZ at levels as low as 0.3 μg kg⁻¹. An excellent correlation of results obtained by ELISA and LC/MS–MS within the concentration range 0–32.1 μg kg⁻¹ was found in the naturally contaminated shrimp samples (r = 0.999, n = 8). A similar correlation was found for the incurred poultry samples within the concentration range of 0–10.5 μg kg⁻¹ (r = 0.99, n = 8).     

A novel sol-gel-based amino-functionalized fiber for headspace solid-phase microextraction of phenol and chlorophenols from environmental samples

A novel amino-functionalized polymer was synthesized using 3-(trimethoxysilyl) propyl amine (TMSPA) as precursor and hydroxy-terminated polydimethylsiloxane (OH-PDMS) by sol–gel technology and coated on fused-silica fiber. The synthesis was designed in a way to impart polar moiety into the coating network. The scanning electron microscopy (SEM) images of this new coating showed the homogeneity and the porous surface structure of the film. The efficiency of new coating was investigated for headspace solid-phase microextraction (SPME) of some environmentally important chlorophenols from aqueous samples followed by gas chromatography–mass spectrometry (GC–MS) analysis. Effect of different parameters influencing the extraction efficiency such as extraction temperature, extraction time, ionic strength and pH was investigated and optimized. In order to improve the separation efficiency of phenolic compounds on chromatography column all the analytes were derivatized prior to extraction using acetic anhydride at alkaline condition. The detection limits of the method under optimized conditions were in the range of 0.02–0.05 ng mL⁻¹. The relative standard deviations (R.S.D.) (n = 6) at a concentration level of 0.5 ng mL⁻¹ were obtained between 6.8 and 10%. The calibration curves of chlorophenols showed linearity in the range of 0.5–200 ng mL⁻¹. The proposed method was successfully applied to the extraction from spiked tap water samples and relative recoveries were higher than 90% for all the analytes.     

Separation and determination of amitriptyline and nortriptyline by dispersive liquid-liquid microextraction combined with gas chromatography flame ionization detection

Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–flame ionization detection (GC–FID) was applied for the determination of two tricyclic antidepressant drugs (TCAs), amitriptyline and nortriptyline, from water samples. This method is a very simple and rapid method for the extraction and preconcentration of these drugs from environmental sample solutions. In this method, the appropriate mixture of extraction solvent (18 μL Carbon tetrachloride) and disperser solvent (1 mL methanol) are injected rapidly into the aqueous sample (5.0 mL) by syringe. Therefore, cloudy solution is formed. In fact, it is consisted of fine particles of extraction solvent which is dispersed entirely into aqueous phase. The mixture was centrifuged and the extraction solvent is sedimented on the bottom of the conical test tube. 2.0 μL of the sedimented phase is injected into the GC for separation and determination of TCAs. Some important parameters, such as kind of extraction and disperser solvent and volume of them, extraction time, pH and ionic strength of the aqueous feed solution were optimized. Under the optimal conditions, the enrichment factors and extraction recoveries were between 740.04–1000.25 and 54.76–74.02%, respectively. The linear range was (0.005–16 μg mL⁻¹) and limits of detection were between 0.005 and 0.01 μg mL⁻¹ for each of the analytes. The relative standard deviations (R.S.D.) for 4 μg mL⁻¹ of TCAs in water were in the range of 5.6–6.4 (n = 6). The performance of the proposed technique was evaluated for determination of TCAs in blood plasma.     

Constructions of a set of novel hydrogen-bonded supramolecules from reactions of cobalt(II) salt with bis(3,5-dimethylpyrazolyl)methane and different carboxylic acids

Reactions of CoX₂·6H₂O (X = Cl⁻, ClO₄⁻) with bis(3,5-dimethylpyrazolyl)methane (dmpzm) and formic acid, acetic acid, benzoic acid, salicylic acid, maleic acid, or fumaric acid under the presence of KOH solution produced a new family of Co(II)/dmpzm complexes, [Co(dmpzm)₂L]X·nH₂O (1: L = O₂CH, X = Cl, n = 2; 2: L = OAc, X = Cl, n = 3; 3: L = benzoate, X = ClO₄, n = 1/3; 4: L = salicylate, X = ClO₄, n = 1/3) and [Co₂(dmpzm)₄L](ClO₄)₂·nSolv (5: L = maleate, n = 3, Solv = H₂O; 6: L = fumarate, n = 2, Solv = MeOH). These compounds were structurally characterized by elemental analysis, IR spectroscopy, and single-crystal X-ray diffraction. Compounds 1–4 are mononuclear while 5–6 are binuclear. Each cobalt atom of 1–6 is hexacoordinate, with a distorted octahedral CoN₄O₂ coordination geometry incorporating two N,N′-bidentate dmpzm ligands and one O,O′-bidentate carboxylate ligand. There are rich intra- and intermolecular hydrogen bonds in the crystals of 1–6, thereby forming either 2D hydrogen-bonded networks (1 and 2) or 3D hydrogen-bonded networks (3–6). In addition, the thermal behaviors of 1–6 were also investigated.     

On-line pretreatment and determination of parabens in cosmetic products by combination of flow injection analysis, solid-phase extraction and micellar electrokinetic chromatography

A convenient and automated method for on-line pretreatment and determination of three parabens (i.e. methyl, ethyl and propyl p-hydroxybenzoate) in cosmetic products is proposed by using flow injection analysis (FIA), solid-phase extraction (SPE) and micellar electrokinetic chromatography (MEKC). An improved split–flow interface is used to couple SPE on C₈-bonded silica with MEKC separation, which can avoid running buffer contamination and reduce buffer consumption, especially, containing expensive reagents. The analytes are loaded onto a C₈ column at 0.6 mL/min for 60 s and eluted with a mixed eluent of 40% (v/v) 10 mmol/L sodium tetraborate buffer (pH 9.3) and 60% (v/v) ethanol at 0.75 mL/min. The MEKC separation is accomplished with a running buffer of 20 mmol/L sodium tetraborate (pH 9.3) containing 100 mmol/L sodium dodecyl sulfate (SDS) at 15 kV. For butyl p-hydroxybenzoate did not be detected in the cosmetic products, it was used as an internal standard (IS) added into the real samples. This FIA–SPE–MEKC method using IS allows the sample separation within 12 min and the sample throughput of five samples per hour with the relative standard deviation (R.S.D.) less than 2.3% (n = 5). The limits of detection (LOD) are in the range from 0.07 to 0.1 μg/mL (S/N = 3 and n = 11). The proposed method has been used to determine three parabens in real cosmetic products satisfactorily.     

Evaluation of solid-phase micro-extraction coupled to gas chromatography-mass spectrometry for the headspace analysis of volatile compounds in cocoa products

The aroma profile of cocoa products was investigated by headspace solid-phase micro-extraction (HS-SPME) combined with gas chromatography–mass spectrometry (GC–MS). SPME fibers coated with 100 μm polydimethylsiloxane coating (PDMS), 65 μm polydimethylsiloxane/divinylbenzene coating (PDMS-DVB), 75 μm carboxen/polydimethylsiloxane coating (CAR-PDMS) and 50/30 μm divinylbenzene/carboxen on polydimethylsiloxane on a StableFlex fiber (DVB/CAR-PDMS) were evaluated. Several extraction times and temperature conditions were also tested to achieve optimum recovery. Suspensions of the samples in distilled water or in brine (25% NaCl in distilled water) were investigated to examine their effect on the composition of the headspace. The SPME fiber coated with 50/30 μm DVB/CAR-PDMS afforded the highest extraction efficiency, particularly when the samples were extracted at 60 °C for 15 min under dry conditions with toluene as an internal standard. Forty-five compounds were extracted and tentatively identified, most of which have previously been reported as odor-active compounds. The method developed allows sensitive and representative analysis of cocoa products with high reproducibility. Further research is ongoing to study chocolate making processes using this method for the quantitative analysis of volatile compounds contributing to the flavor/odor profile.     

Study on interaction between drug and membrane by using liposome coated zirconia-magnesia chromatography

The interactions between drug molecules and membrane were studied using the new chromatography stationary phase of liposome coated zirconia–magnesia. log K_s(ZrO₂–MgO) on this new chromatography for some drugs, compared with that on liposome coated silica chromatography and other reported data, fair correlations were observed between them when excluding effect of special adsorption. log K_s(ZrO₂–MgO) values for barbitalum, diazepam, benzene, benzocaine and toluene correlated well with corresponding values on liposome coated silica chromatography (R = 0.99778, P < 0.001; R = 0.98229, P < 0.003; R = 0.9985, P < 0.0001; R = 0.99925, P < 0.0001, pH value of mobile phase at pH 7.4, 7.0, 6.4 and 5.4, respectively). They also correlated well with the literature data on immobilized artificial membrane chromatography (R = 0.99999, P < 0.004 at pH 7.4) and liposome chromatography (R = 0.99994, P < 0.008) for procaine, lidocaine and bupivacaine. Liposome coated zirconia–magnesia chromatography can thus be used for studying drug–membrane interaction and prediction of drug absorption as another liposome chromatography method.     

Determination of diethylhexyl phtalate in water by solid phase microextraction coupled to high performance liquid chromatography

Difficulties detected in the determination of the diethylhexylphthalate (DEHP) at trace levels by gas chromatography–mass spectrometry (GC–MS) using SPME, due to its ubiquitous distribution in the environment has been overcome and a new method for the determination of DEHP in drinking water has been proposed. The method is based on solid phase microextraction (SPME) coupled to high-performance liquid chromatography (HPLC). Detection was carried out spectrophotometrically. Calibration graph was linear in the range 10–110 μg/L with a regression coefficient of r² = 0.998 and a detection limit of 0.6 μg/L. The relative standard deviation was 5 and 2% (n = 4) for chromatographic areas and retention times, respectively. The usefulness of the SPME–HPLC technique was confirmed.     

Comparative characteristics of texture and properties of hybrid organic–inorganic adsorbents functionalized by amine and thiol groups

The structure and texture characteristics of the hybrid organic–inorganic adsorbents, which were obtained by using of two-component systems of “structure-forming agent/trifunctional silane”, are compared as follows: the first component is Si(OC₂H₅)₄ or (C₂H₅O)₃Si–A–Si(OC₂H₅)₃, where A = –(CH₂)₂– or –C₆H₄–; the second one is alkoxysilane with amine (–NH₂, NH, –NH(CH₂)₂NH₂) and thiol (–SH) groups. The adsorbents, derived from TEOS, have more accessible functional groups (2.6–4.2 mmol/g) than xerogels, which are based on bis(triethoxysilanes) (1.0–2.6 mmol/g). On another hand xerogels derived from bis(triethoxysilanes) have a more extended porous structure (S_sp =516–968 m²/g, V_s = 0.418–1.490 cm³/g, d = 2.5–15.0 nm) than those that are based on TEOS (S_sp = 4–631 m²/g, V_s = 0.005–1.382 cm³/g, d = 2.3–17.7 nm). The geometric dimensions of functional groups have a more essential effect on the parameters of porous structure in the case of TEOS-derived xerogels. Using solid-state NMR spectroscopy, it has been shown that in synthesis of xerogels with the use of TEOS, the molecular frame of globules is formed by structural units Qⁿ (n = 2,3,4), and the functional groups exist as structural units of Tⁿ (n = 2,3). The xerogels obtained with using bis(triethoxysilanes) consist only of structural units of Tⁿ-type (n = 1,2,3).     

An improved procedure for flow-based turbidimetric sulphate determination based on a liquid core waveguide and pulsed flows

An improved flow-based procedure is proposed for turbidimetric sulphate determination in waters. The flow system was designed with solenoid micro-pumps in order to improve mixing conditions and minimize reagent consumption as well as waste generation. Stable baselines were observed in view of the pulsed flow characteristic of the systems designed with solenoid micro-pumps, thus making the use of washing solutions unnecessary. The nucleation process was improved by stopping the flow prior to the measurement, thus avoiding the need of sulphate addition. When a 1-cm optical path flow cell was employed, linear response was achieved within 20–200 mg L⁻¹, described by the equation S = −0.0767 + 0.00438C (mg L⁻¹), r = 0.999. The detection limit was estimated as 3 mg L⁻¹ at the 99.7% confidence level and the coefficient of variation was 2.4% (n = 20). The sampling rate was estimated as 33 determinations per hour. A long pathlength (100-cm) flow cell based on a liquid core waveguide was exploited to increase sensitivity in turbidimetry. Baseline drifts were avoided by a periodical washing step with EDTA in alkaline medium. Linear response was observed within 7–16 mg L⁻¹, described by the equation S = −0.865 + 0.132C (mg L⁻¹), r = 0.999. The detection limit was estimated as 150 μg L⁻¹ at the 99.7% confidence level and the coefficient of variation was 3.0% (n = 20). The sampling rate was estimated as 25 determinations per hour. The results obtained for freshwater and rain water samples were in agreement with those achieved by batch turbidimetry at the 95% confidence level.     

Crystalline polysilicate magadiite with intercalated n-alkylmonoamine and some correlations involving thermochemical data

Synthesized hydrated lamellar acidic crystalline magadiite (H₂Si₁₄O₂₉·2H₂O) nanocompound was used as host for intercalation of polar n-alkylmonoamine molecules of the general formula H₃C(CH₂)_nNH₂ (n = 1–6) in aqueous solution. The original interlayer distance (d) of 1500 pm, determined by X-ray powder diffraction patterns, increases after intercalation. The values correlated with the number of aliphatic amine carbon (n_c) atoms: d = [(1312 ± 11) + (21 ± 2)]n_c. The amount of intercalated amines (N_s), decreased as n_c increased: N_s = [(5.82 ± 0.04) − (0.45 ± 0.01)]n_c. The acidic layered nanocompound was calorimetrically titrated with the amines and the thermodynamic data gave exothermic values for all guest molecules, as shown by the correlation: Δ_intH = −[(24.45 ± 0.49) − (1.91 ± 0.10)]n_c and d = [(1576 ± 16) − (10.8 ± 1.0)]Δ_intH. The negative values of the Gibbs energies and the positive entropies also presented the correlations: Δ_intG = −[(22.8 ± 0.2) − (0.2 ± 0.1)]n_c and Δ_intS = [(6 ± 1) + (5 ± 1)]n_c, respectively.     

Flocculation-ultrasonic assisted extraction and solid phase clean-up for determination of polycyclic aromatic hydrocarbons in water rich in colloidal particulate with high performance liquid chromatography and ultraviolet-fluorescence detection

In the present work, a simple method of sample preparation for the determination of polycyclic aromatic hydrocarbons (PAHs) in water rich in colloidal particulate was developed. The technique was mainly based on the effect of the flocculation of aluminum sulfate and the adsorption of the flocculation aid florisil. The method contained three steps: flocculation, ultrasonic extraction, and solid-phase extraction cleanup. Major parameters of the procedure were optimized with high performance liquid chromatography (HPLC) separation and ultraviolet-fluorescence detection. When 250 mL model sample containing 16 EPA PAHs was processed, the developed method provided detection limits in the range of 0.02–5 ng/L. Both spiked and non-spiked polluted river water samples rich in suspended particles and organic matters were analyzed. Recoveries and relative standard deviations for the 16 PAHs were in ranges of 86–94% and 3–13% (n = 5), respectively.     

Simultaneous determination of total arsenic and total selenium in Chinese medicinal herbs by hydride generation atomic fluorescence spectrometry in tartaric acid medium

By HG-AFS, a new method was proposed for simultaneous determination of total arsenic and total selenium existed in the Chinese medicinal herbs in tartaric acid medium. The effects of analytical conditions and coexisting ions on the fluorescence signal intensity of analytes were investigated. The proposed method was provided with linear response ranges above 22 μg l⁻¹ for As and 44 μg l⁻¹ for Se, and the detection limits of 0.13 and 0.12 μg l⁻¹ were obtained for As and Se respectively. The recoveries of 93.8–96.1% for As and 95.3–99.1% for Se, and the precision of 1.2–3.8% and 2.4–5.3% (R.S.D., n = 8) respectively, were obtained via simultaneous determined four samples of Chinese medicinal herbs and three certified botanic reference materials successfully. The proposed method has the advantages of simple operation, high sensitivity and high efficiency.     

Time measurement-visual analysis of nickel(II) using autocatalytic reaction with sodium sulfite/hydrogen peroxide system and its application to the length detection-flow analysis

Trace amounts of nickel(II) can function as a trigger (=reaction initiator) in an autocatalytic reaction with the sodium sulfite/hydrogen peroxide system. Based on this finding, sub-μg L⁻¹ levels of nickel(II) were determined by a time measurement using the autocatalytic reaction. The detection range using the above method was 10⁻⁹–10⁻⁵ M, the detection limit (3σ) was 8.1 × 10⁻¹⁰ M (0.047 μg L⁻¹), and the relative standard deviation was 2.66% at nickel(II) concentration of 10⁻⁷ M (n = 7). This method was applied to length detection-flow injection analysis. The detection range for the flow injection analysis was 2 × 10⁻⁹–2 × 10⁻³ M. The detection limit (3σ) was 1.4 × 10⁻⁹ M (0.082 μg L⁻¹), and the relative standard deviation was 1.86 at initial nickel(II) concentration of 10⁻⁶ M (n = 7).     

Review of development of a silica-based thermoluminescence dosimeter

Development of a silica-based material suitable for thermoluminescence dosimetry (TLD) is described. Doped silica samples were prepared in-house using the sol–gel technique. Results from a micro-X-ray fluorescence (μ-XRF) study of Zn-doped silica have confirmed the capability of the sol–gel processing steps in producing homogeneously doped samples. The ability of sol–gel processing in producing doped samples with different dopant charge states has been illustrated in the case of copper (I)- and copper (II)-doped silica samples. The charge states of the dopants have been verified using the technique of X-ray absorption near-edge structure (XANES). X-ray diffraction (XRD) investigations have shown the structure of samples doped with erbium, copper (I) and copper (II) (listed in order of decreasing effect) to be altered by the dopants, albeit with the samples remaining in an amorphous state. Local structure studies, carried out using the method of extended X-ray absorption fine structure (EXAFS), reveal that in most cases the local environment of the dopant is similar to the respective native structure of the respective metal oxides. Conversely, in a number of cases, the dopant atoms occupy the silicon sites in the silica tetragonal geometry. Thermoluminescence (TL) studies were carried out on aluminium, copper (I), germanium, manganese, tin, and zinc-doped silica samples. Weight for weight, the most sensitive thermoluminescent material was found to be 4.0 mol% aluminium-doped silica, providing 3.5 times the TL yield of TLD100 and 5.4 times that of germanium-doped silica. The photon dose response of aluminium-doped silica was observed to be linear over the range of investigated dose, 0.5–10.0 Gy.     

Kinetic spectrophotometric method for rapid determination of trace formaldehyde in foods

A simple and sensitive kinetic-spectrophotometric method was developed for the determination of ultra trace amount of formaldehyde in food samples. The method was based on the oxidation of rhodamine B (RhB) by potassium bromate in sulfuric acid medium (formaldehyde as catalyst). The reaction was monitored by measuring the decrease in absorbance of the dye at 515 nm after 6 min. The developed method allowed the determination of formaldehyde in the range of 10–100 μg L⁻¹ with good precision, accuracy and the detection limit was down to 2.90 μg L⁻¹. The relative standard deviations for the determination of 10 and 60 μg L⁻¹ of formaldehyde were 3.0% and 1.9% (n = 10), respectively. The method was found to be sensitive, selective and was applied to the determination of formaldehyde in foods with satisfactory results.     

A multicommuted stop-flow system employing LEDs-based photometer for the sequential determination of anionic and cationic surfactants in water

It has been developed an automatic stop-flow procedure for sequential photometric determination of anionic and cationic surfactants in a same sample of water. The flow system was based on multicommutation process that was designed employing two solenoid micro-pumps and six solenoid pinch valves, which under microcomputer control carry out fluid propelling and reagent solutions handling. A homemade photometer using a photodiode as detector and two light emitting diodes (LEDs) with emission at 470 nm (blue) and 650 nm (red) as radiation sources, which was tailored to allow the determination of anionic and cationic surfactants in waters. The procedure for anionic surfactant determination was based on the substitution reaction of methyl orange (MO) by the anionic surfactant sodium dodecylbenzene sulfonate (DBS) to form an ion-pair with the cetyl pyridine chloride (CPC). Features such as a linear response ranging from 0.35 to 10.5 mg L⁻¹ DBS (R = 0.999), a detection limit of 0.06 mg L⁻¹ DBS and a relative standard deviation of 0.6% (n = 11) were achieved. For cationic surfactant determination, the procedure was based on the ternary complex formation between cationic surfactant, Fe(III) and chromazurol S (CAS) using CPC as reference standard solution. A linear response range between 0.34 and 10.2 mg L⁻¹ CPC (R = 0.999), a detection limit of 0.05 mg L⁻¹ CPC and a relative standard deviation of 0.5% (n = 11) were obtained. In both cases, the sampling throughput was 60 determinations per hour. Reagents consumption of 7.8 μg MO, 8.2 μg CPC, 37.2 μg CAS and 21.6 μg Fe(III) per determination were achieved. Analyzing river water samples and applying t-test between the results found and those obtained using reference procedures for both surfactant types provide no significant differences at 95% confidence level.     

Quantification of residual nitrite and nitrate in ham by reverse-phase high performance liquid chromatography/diode array detector

Nitrite and nitrate are used as additives in ham industry to provide colour, taste and protect against clostridia. The classical colorimetric methods widely used to determine nitrite and nitrate are laborious, suffer from matrix interferences and involve the use of toxic cadmium. The use of chromatography is potentially attractive since it is more rapid, sensitive, selective and provides reliable and accurate results. A rapid and cost-effective RP-HPLC method with diode array detector was optimized and validated for quantification of nitrites and nitrates in ham. The chromatographic separation was achieved using a HyPurity C18, 5 μm chromatographic column and gradient elution with 0.01 M n-octylamine and 5 mM tetrabutylammonium hydrogenosulphate to pH 6.5. The determinations were performed in the linear range of 0.0125–10.0 mg/L for nitrite and 0.0300–12.5 g/L for nitrate. The detection limits were 0.019 and 0.050 mg/kg, respectively. The reliability of the method in terms of precision and accuracy was evaluated. Coefficients of variation lower than 2.89% and 5.47% were obtained for nitrite and nitrate, respectively (n = 6). Recoveries of residual nitrite/nitrate ranged between 93.6% and 104.3%. Analysis of cooked and dried ham samples was performed, and the results obtained were in agreement with reference procedures.