An improved bonded-polydimethylsiloxane solid-phase microextraction fiber obtained by a sol-gel/silica particle blend

A novel procedure for solid-phase microextraction fiber preparation is presented, which combines the use of a rigid titanium alloy wire as a substrate with a blend of PDMS sol–gel mixture/silica particles, as a way of increasing both the mechanical robustness and the extracting capability of the sol–gel fibers. The 30 μm average thick fibers displayed an improvement in the extraction capacity as compared to the previous sol–gel PDMS fibers, due to a greater load of stable covalently bonded sol–gel PDMS. The observed extraction capacity was comparable to that of 100 μm non-bonded PDMS fiber, having in this case the advantages of the superior robustness and stability conferred, respectively, by the unbreakable substrate and the sol–gel intrinsic characteristics. Repeatability (n = 3) ranged 1–8% while fiber production reproducibility (n = 3) ranged 15–25%. The presence of the silica particles was found to have no direct influence on the kinetics and mechanism of the extraction process, thus being possible to consider the new procedure as a refinement of the previous ones. The applicability potential of the devised fiber was illustrated with the analysis of gasoline under the context of arson samples.     

The effect of lanthanide on the degradation of RB in nanocrystalline Ln/TiO2 aqueous solution

A series of Nd³⁺, Pr³⁺, Er³⁺, and Dy³⁺ (0.25–5 at.%) homogeneously doped nanocrystalline titanium dioxides (Ln/TiO₂) were prepared by an easy sol–gel technique, and the roles of lanthanide doping on the photocatalytic activity in the degradation of rhodamine B (RB) in aqueous solution were studied. Both the concentration of the lanthanide dopant and calcination temperature showed significant effect to the photodegradation of RB. The photocatalytic activity of pure titania was drastically decreased when calcination temperature was at 700 °C, while the high photocatalytic activity was still maintained for lanthanide-doped samples. HPLC-MS method was used to study the degradation process, and it is demonstrated that the degradation of RB catalyzed by Ln/TiO₂ was principally go through with a stepwise de-ethylation photochemical process.     

Electrochemical behavior of methyl viologen at graphite electrodes modified with Nafion sol–gel composite

Electrodes were prepared by spin-coating spectroscopic graphite rods with a Nafion doped sol. Coating solutions consisting of Nafion:TEOS (tetraethoxysilane) ratios of 3:1 and 4:1 gave smooth films on the electrode surface. These modified electrodes were evaluated and compared with Nafion modified and bare spectroscopic graphite electrodes using methyl viologen (MV²⁺) as a representative cationic electroactive probe. Substantial partitioning of MV²⁺ into the Nafion:sol–gel matrix to the electrode surface was observed by cyclic voltammetry and square wave voltammetry. Cyclic voltammograms of MV²⁺ in 0.1 M NaCl at Nafion:sol–gel 4:1 modified electrodes showed a reversible reduction to MV⁺ with E^0′=−0.695 V vs. Ag/AgCl. Results of scan rate variation showed the wave to be characterized by semi-infinite diffusion for scan rates in the range 50–500 mV/s. Slowing the scan rate below 50 mV/s resulted in a transition to thin-layer behavior. MV²⁺ partitioned much more quickly into the sol–gel-Nafion modified electrodes compared to pure Nafion modified electrodes. Reversibility of the MV²⁺-loaded modified Nafion-doped sol–gel coatings on electrodes was obtained by soaking in 1 M NaCl solution. Concentration calibration plots for MV²⁺ at the sol–gel-Nafion modified electrodes were nonlinear. Substantial enhancement of current signal at low concentrations was observed by square wave voltammetry.     

Amperometric detection of cytochrome c by capillary electrophoresis at a sol–gel carbon composite electrode

Capillary electrophoresis (CE) was employed for the determination of cytochrome c using a wall-jet amperometric detector consisting a copper(I) oxide-modified sol–gel carbon composite electrode (CCE), which exhibits a sensitive electrocatalytic response for the oxidation of cytochrome c. The optimum conditions of separation and detection are 0.08 M NaOH for the separation solution, 12 kV for separation voltage and +0.60 V versus saturated calomel electrode (SCE) for the detection potential. Calibration was linear over the concentration range 1–600 μM with the limit of detection of 3.4 μM, based on a signal-to-noise ratio (S/N) of 3.     

Density fractionated hollow silica microspheres with high-yield by non-polymeric sol–gel/emulsion route

Hollow silica microspheres were synthesized by non-polymeric sol–gel/emulsion technique using tetra ethyl orthosilicate (TEOS) as a source of silica. A sol mixture of TEOS, water, ethanol and acid was emulsified in a solution of light paraffin oil and surfactant (Span-80). Calcined spheres were density fractionated between density ranges: <1.0, 1.0–1.594, 1.594–1.74 and >1.74 g cm⁻³. The samples were characterized by optical and scanning electron microscopy with energy dispersive X-ray analysis, Fourier transform infrared spectroscopy and laser diffraction size analyzer. Spheres of densities lower than 1.74 g cm⁻³ were found to be hollow as observed from scanning electron microscopy (SEM) images and their yield was maximized to 100% by using a specific TEOS volume ratio with respect to volumes of surfactant and oil. Decreasing the calcination temperature from 700 to 500 °C enhances the yield of hollow spheres emphasizing importance of slower diffusion kinetics at lower calcination temperature. Outer diameters of spheres were between 5 and 60 μm with mean diameter expectedly increasing with increase in TEOS sol volume and with decrease in sphere density. It is proposed that silica shells form via hydrolysis and polycondensation at oil–water/ethanol interface in the water-in-oil emulsion, which subsequently form hollow spheres on removal of water–ethanol during calcination.     

Application of amperometric sol-gel biosensor to flow injection determination of glucose

A glucose biosensor with enzyme immobilised by sol–gel technology was constructed and evaluated. The glucose biosensor reported is based on encapsulated GOX within a sol–gel glass, prepared with 3-aminopropyltriethoxy silane, 2-(3,4-epoxycyclohexyl)-ethyltrimetoxy silane and HCl. A flow system incorporating the amperometric biosensor constructed was developed for the determination of glucose in the 1×10⁻⁴–5×10⁻³ mol l⁻¹ range with a precision of 1.5%. The results obtained for the analysis of electrolytic solution for iv administration and human serum samples showed good agreement between the proposed method and the reference procedure, with relative error <5%.     

Synthesis and characterization of new azobenzenesulfonic acids doped conducting polyaniline

New azobenzene sulfonic acid dopants were synthesized by diazotized coupling reaction of sulphanilic acid diazonium salt with commercially available raw materials such as phenol, m-cresol and 4-phenylphenol. The structures of the dopants are confirmed by NMR and FT-IR. Polyaniline emeraldine base was doped by these new azobenzenesulfonic acid dopants in two different solvent medium such as methanol and N-methylpyrrolidinone to produce green emeraldine salt. The doping process was confirmed by FT-IR and UV-vis spectroscopy. The effect of composition of dopant on the conductivity of the polyaniline was investigated and the results suggest that the conductivity increases with the increase in the dopant concentration and attained maxima for more than 38% in the feed. The conductivity measurements reveal that all the dopants equally effective in producing in high conductivity in the range of 0.02 S/cm and the conductivity of the doped samples are insignificant to the structural difference in the dopant. WXRD and SEM analysis indicate that the doped samples are highly amorphous and porous in nature. The thermal analysis by TGA indicate that all the doped materials were highly stable up to 300 °C for high temperature applications.     

Effects of sol-gel processing parameters on the phases and microstructures of HA films

Bioactive hydroxyapatite (HA) films were fabricated by a sol–gel method and triethylphosphate and calcium nitrate were used as the phosphorus and calcium precursors, respectively. The effects of the heat treatment temperature, pH level and substrate materials on the phases and microstructures of HA films were studied by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and electronic probe microanalysis (EPMA) and so on. The results show that all the sol–gel films are composed of the phases of HA, CaO, TiO₂ and CaTiO₃. With increasing the calcining temperature, the crystallinity of the films increases, the structure becomes more compact and changes from granular and lamellar to cellular structure, and the Ca/P ratio increases slightly because of the loss of P in the films. The addition of ammonia (adjusting the pH level to be about 7.5) can increase the HA content in the films, and the difference of substrate materials only has a little influence on the microstructure of the sol–gel films.     

Headspace solid-phase microextraction with novel sol–gel permethylated-β-cyclodextrin/hydroxyl-termination silicone oil fiber for determination of polybrominated diphenyl ethers by gas chromatography–mass spectrometry in soil

A simple, sensitive, and accurate method for determination of polybrominated diphenyl ethers (PBDEs) in soil has been developed based on headspace solid-phase microextraction (HS-SPME) followed by gas chromatography–mass spectrometry (GC–MS). Permethylated-β-cyclodextrin/hydroxyl-termination silicone oil (PM-β-CD/OH-TSO) fiber was first prepared by sol–gel technology and employed in SPME procedure. By exploiting the superiorities of sol–gel coating technique and the advantages of the high hydrophobic doughnut-shaped cavity of PM-β-CD, the novel fiber showed desirable operational stability and extraction ability. After optimization on extraction conditions like water addition, extraction temperature, extraction time, salts effect, and solvents addition, the method was validated in soil samples, achieving good linearity (r > 0.999), precision (R.S.D. < 10%), accuracy (recovery > 78%), and detection limits (S/N = 3) raging from 13.0 to 78.3 pg/g.     

Atomic size effects on recombination processes during thermoluminescence in doped crystals

Atomic size effects on recombination processes during thermoluminescence (TL) in KCl: Harshaw (nominally pure samples), KCl: Ag (14 ppm), KCl: Na(>250 ppm) and KCl: Li (1 ppm) following room temperature (RT) γ-irradiation (20Mrad) has been examined. Results show that the stability of defects increases with decreasing dopant atomic size. (Peak temperatures are 210°C, 255°C and 277, 5°C in Ag-doped Na-doped and Li-doped samples respectively.) The trap-depth also increases as atomic size of dopants decreases. Emission spectrum indicates that only a perturbation of the well known band peak at 440 nm is caused by impurities. Additional band peaks occur in Ag-doped samples.     

Thermoluminescence study of Cu,Ag and Mn doped lithium tetraborate single crystals and glasses

Spectrally resolved thermoluminescence (TL) of non-doped and Ag, Cu^? and Mn-doped lithium-tetraborate (LTB) single crystals revealed that TL emission bands for differently doped samples proved to be at different wavelengths: 272, 370 and 608 nm, respectively. These bands perfectly agree with the photoluminescence (PL) emission bands of Ag⁺, Cu⁺ and Mn²⁺ ions. It strongly points that these dopants are directly involved as recombination centers in the TL process.TL characteristics of non-doped and doped LTB single crystals and the corresponding glassy samples showed that their TL intensities and the structures of the glow curves were apparently different.     

8-Hydroxyquinoline anchored to silica gel via new moderate size linker: synthesis and applications as a metal ion collector for their flame atomic absorption spectrometric determination

The silica gel modified with (3-aminopropyl-triethoxysilane) was reacted with 5-formyl-8-hydroxyquinoline (FHOQ_x) to anchor 8-quinolinol ligand on the silica gel. It was characterised with cross polarisation magic angle spinning (CPMAS) NMR and diffuse reflectance infrared Fourier transformation (DRIFT) spectroscopy and used for the preconcentration of Cu(II), Pb(II), Ni(II), Fe(III), Cd(II), Zn(II) and Co(II) prior to their determination by flame atomic absorption spectrometry. The surface area of the modified silica gel has been found to be 227 m² g⁻¹ and the two pKa values as 3.8 and 8.0. The optimum pH ranges for quantitative sorption are 4.0–7.0, 4.5–7.0, 3.0–6.0, 5.0–8.0, 5.0–8.0, 5.0–8.0 and 4.0–7.0 for Cu, Pb, Fe, Zn, Co, Ni and Cd, respectively. All the metals can be desorbed with 2.5 mol l⁻¹ HCl or HNO₃. The sorption capacity for these metal ions is in range of 92–448.0 μmol g⁻¹ and follows the order Cd3, NaCl, NaBr, Na₂SO₄ and Na₃PO₄, glycine, sodium citrate, EDTA, humic acid and cations Ca(II), Mg(II), Mn(II) and Cr(III) in the sorption of all the seven metal ions are reported. The preconcentration factors are 150, 250, 200, 300, 250, 300 and 200 for Cd, Co, Zn, Cu, Pb, Fe and Ni, respectively and t_1/2 values <1 min except for Ni. The 95% extraction by batch method takes ≤25 min. The simultaneous enrichment and determination of all the metals are possible if the total load of the metal ions is less than sorption capacity. In river water samples all these metal ions were enriched with the present ligand anchored silica gel and determined with flame atomic absorption spectrometer (R.S.D.≤6.4%). Cobalt contents of pharmaceutical samples (vitamin tablet) were preconcentrated with the present chelating silica gel and estimated by flame AAS, with R.S.D.1.4%. The results are in the good agreement with the certified value, 1.99 μg g⁻¹ of the tablets. Iron and copper in certified reference materials (synthetic) SLRS-4 and SLEW-3 have been enriched with the modified silica gel and estimated with R.S.D.<5%.     

Control of the morphology of oxide nano-islands through the substrate miscut angle

An experimental method is presented that allows to control the morphology of sol–gel grown epitaxial thin films. Thin films of yttria stabilized zirconia (YSZ) have been grown on two c-cut sapphire substrates by sol–gel dip-coating and epitaxial nano-islands have been formed by high temperature thermal treatment. Atomic force microscopy observations and X-ray diffraction reciprocal space mapping were used to investigate the effects of a step-like structure of the wafer surface on the morphology and on the out-of-plane orientation of epitaxial nano-islands. In all cases investigated the (002) planes of YSZ remained parallel to the (0001) planes of sapphire, but tilted by an amount depending on both the out-of-plane lattice mismatch and miscut angle.     

Potentiometric detection of exogenic beta-adrenergic substances in liquid chromatography

Generation of a large number of theoretical plates was attempted by capillary HPLC. Monolithic silica columns having small skeletons (ca. 2 μm) and large through-pores (ca. 8 μm) were prepared by a sol–gel method in a fused-silica capillary (50 μm I.D.), and derivatized to C₁₈ phase by on-column reaction. High external porosity (>80%) and large through-pores resulted in high permeability (K=1.2×10⁻¹² m²). The monolithic silica column in the capillary produced a plate height of about 12 μm in 80% acetonitrile at a linear velocity of 1 mm/s. Separation impedance, E value, was found to be as low as 200, that was about an order of magnitude lower than reported values for conventional columns packed with 5 μm particles. Reproducibility of preparation within ±15% was obtained for column efficiency and for pressure drop. It was possible to generate 100,000 plates by using a 130-cm column at very low pressure (<7 kg/cm²). A considerable decrease in column efficiency was observed at high linear velocity, and for solutes with large retention factors due to the slow mobile-phase mass transfer in the large through-pores. The monolithic silica columns, however, showed performance beyond the limit of conventional particle-packed columns in HPLC under favorable conditions.     

金属氧化物掺杂改善LiFePO4电化学性能

采用氧化物前驱体对磷酸铁锂(LiFePO₄)进行少量金属离子掺杂，并用XRD，SEM和恒电流充放电对掺杂的LiFePO₄进行了研究。结果表明，少量的掺杂离子在很大程度上提高了LiFePO₄的电化学性能，特别是大电流放电性能。1.0 mol%的Nb⁵⁺掺杂LiFePO₄的0.1 C放电容量约150 mAh·g^-1；即使在3 C倍率下放电，也有117 mAh·g^-1的容量。掺杂的效果与掺杂离子的半径、价态密切相关，半径小、价态高的离子对提高LiFePO₄的电化学性能有利。在掺杂量较小时(<2.0 mol%)，掺杂效果与掺杂离子的浓度关系不大。     

Emission properties and applications of nanostructured luminescent oxide nanoparticles

Rare earth doped oxide materials are well known for their numerous applications in light emitting devices. An interesting issue is to study the emission properties of nanoparticles, with the aim to understand the influence of small size and surface effects on the emission processes. These particles could furthermore be used in new applications such as the elaboration of transparent emitting devices or new biological labels. The work presented here concerns highly luminescent rare earth doped yttrium vanadates (YVO₄:Eu) and lanthanum phosphate LaPO₄:Ce,Tb·xH₂O nanoparticles. Simple aqueous colloidal syntheses are used for the elaboration of concentrated colloids based on the progressive decomposition of polymeric precursors at moderate temperature (60–90 °C). Both types of particles exhibit strong emission (quantum yields of 25% and 45% for vanadates and phosphates, respectively), but significantly lower than that for the equivalent bulk materials. The alteration of the emission processes is discussed in terms of surface quenching effects. Improvements are obtained through the elaboration of core/shell nanostructures. Surface derivatization has been achieved through the controlled growth of an organically modified silica shell using a functionalized silane precursor. Two examples are given concerning the applications of those particles. The first one is the elaboration of transparent and highly luminescent thin films, obtained by the dispersion of the functionalized particles in a sol–gel silica matrix. The other one is the use of guanidine functionalized particles as biological labels for the single particle detection of sodium channels in cardiac cells.     

Design and application of a flow cell for carbon-film based electrochemical enzyme biosensors

A flow cell has been designed for use with an electrochemical enzyme biosensor, based on low-cost carbon-film electrodes. Three types of mediators were used: cobalt and copper hexacyanoferrates and poly(neutral red) (PNR), covered with glucose oxidase (GOx) immobilised by cross-linking with glutaraldehyde in the presence of bovine serum albumin or inside a oxysilane sol–gel network. Mixtures of sol–gel precursors were made from 3-aminopropyl-triethoxysilane (APTOS) together with methyltrimethoxysilane (MTMOS), methyltriethoxysilane (MTEOS), tetraethyloxysilane (TEOS) or 3-glycidoxypropyl-trimethoxysilane (GOPMOS), and the best chosen for encapsulation. Optimisation in batch mode, using amperometric detection at fixed potential, showed the PNR-GOx modified carbon-film electrodes to be best for flow analysis for both glutaraldehyde and sol–gel enzyme immobilisation. Both types of enzyme electrode were tested under flow conditions and the reproducibility and stability of the biosensors were evaluated. The biosensors were used for fermentation monitoring of glucose in grape must and interference studies were also performed.     

Dopant effect and characterization of polypyrrole-cellulose composites prepared by in situ polymerization process

Polypyrrole (PPy)-cellulose composites were prepared by in situ polymerization of pyrrole in pulp suspension using ferric chloride as an oxidant. Some sulfonic compounds including p-toluenesulfonic acid and its sodium salt (PTSA and PTSA-Na), benzenesulfonic acid (BSA), dodecylbenzene sulfonic acid and its sodium salt (DBSA and DBSA-Na), 2-naphthalene sulfonic acid (NSA) and 9,10-anthraquinone-2-sulfonic acid sodium salt (AQSA-Na) were used as dopants, and their effect on the conductivity of PPy-cellulose composite was investigated. The results showed that the species and dose of dopants had significant effect on the surface resistivity and environmental stability of PPy-cellulose composite. As the dopant, PTSA and DBSA had a superior doping effect compared to their sodium salts. The doping result of BSA was close to that of PTSA. NSA bearing a naphthalene ring and AQSA-Na bearing an anthraquinone ring gave the best conductivity. Using NSA or AQSA-Na as a dopant, along with suitable polymerization conditions, the PPy-cellulose composite obtained showed a surface resistivity as low as 20 Ω cm⁻². For most dopants, the lowest surface resistivity could be obtained when the molar ratio of dopant to pyrrole was 1:1. Both ATR-FTIR (attenuated total reflection-Fourier transform infrared spectroscopy) and XPS (X-ray photoelectron spectroscopy) analysis confirmed that the PPy on pulp fibers doped with PTSA, PTSA-Na, NSA and AQSA-Na had different doping levels. The higher doping level of the PPy in the composites doped with NAS and AQSA-Na might be related to the stronger interaction of cellulose with PPy chains. Both SEM (scanning electron microscopy) and AFM (atomic force microscopy) observation revealed the fine grain microstructure of the PPy on the composites with average grain sizes in the range of 100–200 nm, and the PPy on the samples doped with NSA and AQSA-Na exhibited quite different morphology as compared to those doped with PTSA and its sodium salt.     

Fe3+/V5+/TiO2复合纳米微粒光催化性能的研究

采用溶胶凝胶法制备了Fe^3 /V^5 /TiO2复合纳米微粒作为光催化剂。光降解反应结果表明，其掺杂催化剂Fe^3 /V^5 /TiO2的光催化活性明显提高。光电化学研究显示，铁离子可以成为电荷陷阱，促进空穴的界面传递反应。适量钒离子掺杂使TiO2电极的光电流升高，导带中电子浓度的增大，加快了界面的电子传递反应。共掺杂催化剂中，Fe^3 、V^5 分别提供了空穴与电子的陷阱，同时加快了电子与空穴的界面传递反应，从 更有效地提高光催化活性。双组份共掺杂为提高TiO2光催化活性提供新的途径。     

Sol–gel synthesis and crystallisation of 3CaO·2SiO2 glassy powders

A gel of composition 3CaO·2SiO₂ was synthesised by means of sol–gel route involving hydrolysis of tetramethyl orthosilicate (TMOS) with calcium nitrate in alcoholic medium, and polycondensation reaction. The gel was submitted to DTA and TGA analysis and the resulted material was examined by FTIR spectroscopy and X-ray powder diffractometry. The thermal treatments required for the gel into glass conversion led to a partially devitrified product. The XRD analysis showed that the structure obtained is highly depolymerised.