苯并噻唑和铁氧化物纳米粒子修饰的磁性棒碳糊电极上肼的电催化氧化反应:同时检测肼和苯酚（英文）

开发了一种磁性Fe_3O_4纳米粒子和2-(3,4-二羟苯基)苯并噻唑(DPB)修饰的磁性棒碳糊电极(MBCPE)用于电化学检测肼.首先将DPB自组装在Fe_3O_4纳米粒子上,然后将此复合物吸附于设计的MBCPE上.MBCPE电极将磁性纳米粒子吸引到电极表面.所得新型电极具有高的导电性和大的有效比表面积,因而对肼的电催化氧化反应有非常大的电流响应.采用伏安法、扫描电镜、电化学阻抗谱、红外光谱和紫外-可见光谱对修饰电极进行了表征.采用伏安法研究了在磷酸盐缓冲溶液(pH=7.0)中MBCPE/Fe_3O_4NPs/DPB电极上肼的电化学行为.作为电化学传感器,MBCPE/Fe_3O_4NPs/DPB电极对肼氧化反应表现出极高的电催化活性.在DPB存在下,肼的氧化电势下降,但其催化电流增加.电催化电流与肼浓度在0.1–0.4和0.7–12.0μmol/L二个区间内表现出线性关系,检测限为18.0 nmol/L.另外,研究了MBCPE/Fe_3O_4NPs/DPB电极同时检测肼和苯酚的性能.伏安实验结果显示,苯酚的线性区域为100–470μmol/L,检测限为24.3μmol/L.采用此电极检测了水样品中的肼和苯酚.     

磁性石墨烯纳米粒子修饰电极的制备及其对肼的测定

以氧化石墨烯和Fe~(3+)为原料,采用溶剂热法合成了磁性石墨烯(Fe_3O_4@rGO)纳米复合材料,并以扫描电镜和X-射线衍射谱对复合材料的形貌和结构进行了表征。将Fe_3O_4@rGO组装到磁性玻碳电极(mGCE)表面,得到了Fe_3O_4@rGO/mGCE。研究了该修饰电极的电化学性能,并利用循环伏安法和计时电流法研究了此修饰电极对肼的电催化氧化性能。Fe_3O_4@rGO纳米粒子具有较高的导电效率,可加快电极表面电荷传递速度,同时该纳米粒子对肼的电催化氧化作用显著的促进作用。     

基于Fe3O4@Ag壳核结构磁性纳米复合物的对杀螟硫磷的电化学传感

制备一种壳核结构的Fe3O4@Ag磁性纳米粒子,将该纳米粒子通过壳聚糖（CS）修饰在玻碳电极（GCE）表面,制备了对杀螟硫磷有灵敏电化学传感的Fe3O4@Ag/CS/GCE。应用透射电镜（TEM）和紫外可见光谱（UV-VIS）,对Fe3O4@Ag纳米粒子进行表征。运用电化学交流阻抗（EIS）、循环伏安法（CV）和时间电流法（I-T）来研究杀螟硫磷电化学特性。研究发现,在1.74×10-7～3.27×10–4 mol/L浓度范围内,该传感器可以实现对杀螟硫磷的快速检测,检测限为5.7×10-8 mol/L（S/N=3）     

纳米金与磁性纳米复合物构建电流型免疫传感器的研究

制备了易于磁性分离、硫堇(Thi)包覆的四氧化三铁(Fe3O4)纳米复合物。通过静电吸附作用,将萘酚(Nafion)、Thi包覆的Fe3O4复合纳米粒子层层修饰到玻碳电极表面,再利用Thi分子中的氨基吸附纳米金,最后固载甲胎蛋白抗体,从而制得灵敏度高、稳定性好的无试剂电流型甲胎蛋白免疫传感器。实验通过透射电子显微镜(TEM)对该复合纳米粒子进行表征,并用循环伏安法考察了电极的电化学特性。结果表明,Fe3O4/Thi复合纳米粒子修饰的电极在实验过程中呈现出良好的氧化还原活性,其检测范围为0.05～20μg/L,检出限为0.03μg/L。     

NO2-在CTMAB-氧化钕纳米修饰电极上的电化学行为及其测定

制备了十六烷基三甲基溴化铵-氧化钕纳米修饰电极。用循环伏安法和示差脉冲伏安法研究了NO2-在该修饰电极上的电化学行为,结果表明,该修饰电极对NO2-的氧化具有良好的电催化能力,NO2-的氧化峰电流与其浓度在3.33×10-8～1.04×10-6mol/L范围内呈现良好的线性关系,检测限为9.86×10-9mol/L(S/N=3)。此外,该修饰电极具有良好的重现性和稳定性。本方法可用于NO2-实际样品的测定。     

氧化钕-单壁碳纳米管修饰玻碳电极对鸟嘌呤和腺嘌呤的电催化氧化

制备了氧化钕-单壁碳纳米管修饰玻碳电极(Nd2O3-SWNTs/GCE)。采用循环伏安法(CV)探究了鸟嘌呤(G)和腺嘌呤(A)在该修饰电极上的电化学行为。结果表明:该修饰电极对G和A的氧化具有良好的电催化能力。在最佳条件下,用示差脉冲伏安法(DPV)对G和A进行检测,其氧化峰电流与浓度分别在10~50μmol/L范围内呈现良好的线性关系,检出限(S/N=3)均为5.0×10-8 mol/L。该修饰电极可以用来同时测定DNA中的G和A。     

新型Fe3O4纳米颗粒修饰玻碳电极对头孢噻肟钠的电催化还原及其测定

采用滴涂法将Fe3O4磁性纳米颗粒修饰在玻碳电极上,制得新型纳米Fe3O4修饰电极(Fe3O4-np/GC 电极).X射线衍射光谱表明,纳米Fe3O4为面心立方尖晶石结构,透射电子显微镜表明,纳米Fe3O4粒径15～20 nm的微球结构.采用扫描电子显微镜和交流阻抗法(EIS)对修饰电极表面进行了表征,发现纳米Fe3O4在电极表面形成了均匀的修饰膜.采用循环伏安法(CV)、微分脉冲伏安法(DPV)研究了头孢噻肟钠(CS)在修饰电极上的电化学行为及动力学性质,结果表明,CS在Fe3O4-np/GC电极上有敏锐的催化还原峰,且CS的还原峰电流与其浓度在7.0×10-8～1 ×10-6和1 ×10-6～4.5×10-5 mol/L范围内呈线性关系;检出限达到5.0×10-8 mol/L.该方法可用于市售头孢噻肟钠针剂中CS含量的测定,加标回收率达到96.6％～102.7％.     

基于Fe_3O_4-Au磁性纳米粒子及碳纳米管修饰电极的对氧磷生物传感器研究

采用化学共沉淀技术制备磁性Fe3O4-Au纳米粒子复合物(Fe3O4-AuNPs),并以此磁性纳米复合物和碳纳米管(CNTs)构建用于快速检测对氧磷的乙酰胆碱酯酶(AChE)生物传感器。通过磁力作用将Fe3O4-AuNPs纳米粒子固定在自制的磁铁/玻碳电极(MGCE)上,并以此作为AChE的载体。分别通过X射线衍射、振动样品磁强和透射电镜表征了磁性纳米粒子复合物Fe3O4-AuNPs的成分、磁性及其形貌特征。利用电化学交流阻抗(EIS)、循环伏安法和微分脉冲伏安法(DPV)表征了自制的MGCE修饰电极以及生物传感器(AChE/Fe3O4-AuNPs/CNTs/MGCE)的电化学特征,建立了用该生物传感器微分脉冲伏安法检测对氧磷的方法。在最佳实验条件下,酶抑制率与对氧磷浓度的对数在3.6×10-6~2.9×10-2mol/L范围内呈线性关系,检出限为1.6×10-7mol/L。用提出的方法对实际水样中的对氧磷进行加标回收实验,回收率为98.0%~107%。     

NO2-在CTMAB-碳纳米管修饰电极上的电化学行为及测定

制备了十六烷基三甲基溴化铵-多壁碳纳米管修饰电极.用循环伏安法和示差脉冲伏安法研究了NO2 -在该修饰上的电化学行为,该修饰电极对NO2 -的氧化具有良好的电催化能力,NO2 -的氧化峰电流与其浓度在1.67×10-7 ～2.2×10 -5mol/L范围内呈现良好的线性关系,检测限为5.6×10-8mol/L(S/N=...     

铁氰化镍的磁性纳米粒子合成及化学修饰电极的制备

将镍粒子表面功能化,合成了磁性纳米铁氰化镍（NiHCF）粒子,制备了磁性NiHCF修饰磁控玻碳电极。 在pH=7.4的磷酸盐缓冲溶液中,磁性NiHCF纳米粒子修饰电极对水合肼氧化有显著的催化作用,NiHCF的氧化峰电流与水合肼浓度在0~1.29×10-4 mol/L范围内呈良好的线性关系（安培法）,检出限为2.1×10-8 mol/L。 研究了磁性NiHCF粒子修饰电极对水合肼的电化学响应以及电极的性能,并将其应用于水样中肼的测定。 该修饰电极具有灵敏度高、选择性好、电极易更新、稳定性好和制作简单等优点。     

方波伏安法测定新型修饰多壁碳纳米管糊电极对肼的电催化氧化(英文)

The application of p-aminophenol as a suitable mediator, as a sensitive and selective voltammetric sensor for the determination of hydrazine using square wave voltammetric method were described. The modified multiwall carbon nanotubes paste electrode exhibited a good electrocatalytic activity for the oxidation of hydrazine at pH = 7.0. The catalytic oxidation peak currents showed a linear dependence of the peaks current to the hydrazine concentrations in the range of 0.5–175 μmol/L with a correlation coefficient of 0.9975. The detection limit (S/N = 3) was estimated to be 0.3 μmol/L of hydrazine. The relative standard deviations for 0.7 and 5.0 μmol/L hydrazine were 1.7 and 1.1%, respectively. The modified electrode showed good sensitivity and selectivity. The diffusion coefficient (D = 9.5 × 10–4 cm2/s) and the kinetic parameters such as the electron transfer coefficient (α = 0.7) of hydrazine at the surface of the modified electrode were determined using electrochemical approaches. The electrode was successfully applied for the determination of hydrazine in real samples with satisfactory results.     

Application of a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole/carbon nanotube modified glassy carbon electrode for voltammetric determination of hydrazine in water samples

The electrochemical behaviour of hydrazine at a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole‐triazole/carbon nanotube modified glassy carbon electrode has been studied. The modified electrode shows an excellent electrocatalytic activity for the oxidation of hydrazine and accelerates electron transfer rate. The electrocatalytic current increases linearly with hydrazine concentration in the range 0.5–700.0 μm and the detection limit for hydrazine was 33.0 ± 2.0 nm . The diffusion coefficient (D = 2.5 ± 0.1 × 10^?5 cm² s^?1) and kinetic parameters such as the electron transfer coefficient, (α = 0.52) and the heterogeneous rate constant (k′ = 5.5 ± 0.1 × 10^?3 cm s^?1) for hydrazine were determined using electrochemical approaches. Finally, the method was employed for the determination of hydrazine in water samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Homogeneous and nanomolar detection of hydrazine by indigocarmine as a mediator at the surface of TiO2 nanoparticles modified carbon paste electrode

The homogeneous electrocatalytic oxidation of hydrazine（HZ） has been studied by indigocarmine（IND） as a mediator at the surface of TiO₂ nanoparticles modified carbon paste electrode（TNMCPE）.Cyclic voltammetry was used to study the electrochemical behavior of IND at different scan rates.The voltammetric response of the modified electrode was linear against the concentration of HZ in the ranges of 3.0×l0^-8-7.0×10⁶ mol/L with differential pulse voltammetry method.The detection limit（3σ） was determined as 27.3 nmol/L.To evaluate the applicability of the proposed method to real samples,the modified CPE was applied to the determination of HZ in water samples.     

磁性普鲁士蓝纳米颗粒的合成及其化学修饰电极的制作

利用FeSO₄与FeCl₃合成了超细磁性Fe₃O₄纳米颗粒, 并进一步利用该纳米颗粒与铁氰酸钾在酸性溶液(pH～2)中的化学反应成功制备了一种新型的磁性普鲁士蓝纳米颗粒; 研究了该磁性颗粒的磁学性能, 通过磁力将其修饰于固体石蜡碳糊电极表面制成了化学修饰电极, 考察了该电极对过氧化氢的电催化还原及对水合肼的电催化氧化特性. 该化学修饰电极可对过氧化氢和水合肼进行测定, 线性范围分别为过氧化氢2×10^－6～5×10^－3 mol/L, 水合肼7.2×10^－7～3.6×10^－4 mol/L. 利用磁性普鲁士蓝纳米颗粒制得的修饰电极具有催化性能高、稳定性好、表面易更新等优点.     

Electrochemistry and electrocatalytic activity of catechin film on a glassy carbon electrode toward the oxidation of hydrazine

A very stable electroactive film of catechin was electrochemically deposited on the surface of activated glassy carbon electrode. The electrochemical behavior of catechin modified glassy carbon electrode (CMGCE) was extensively studied using cyclic voltammetry. The properties of the electrodeposited films, during preparation under different conditions, and the stability of the deposited film were examined. The charge transfer coefficient (α) and charge transfer rate constant (k _s) for catechin deposited film were calculated. It was found that the modified electrode exhibited excellent electrocatalytic activity toward hydrazine oxidation and it also showed a very large decrease in the overpotential for the oxidation of hydrazine. The CMGCE was employed to study electrocatalytic oxidation of hydrazine using cyclic voltammetry, rotating disk voltammetry, chronoamperometry, amperometry and square-wave voltammetry as diagnostic techniques. The catalytic rate constant of the modified electrode for the oxidation of hydrazine was determined by cyclic voltammetry, chronoamperometry and rotating disk voltammetry and was found to be around 10⁻³ cm s⁻¹ . In the used different voltammetric methods, the plot of the electrocatalytic current versus hydrazine concentration is constituted of two linear segments with different ranges of hydrazine concentration. Furthermore, amperometry in stirred solution exhibits a detection limit of 0.165 μM and the precision of 4.7% for replicate measurements of 40.0 μM solution of hydrazine.     

Preparation of nanostructured Co–Mo alloy electrodes and investigation of their electrocatalytic activity for hydrazine oxidation in alkaline medium

Cobalt and cobalt–molybdenum alloy electrodes are prepared by galvanic deposition on copper substrates. In this paper, we report a study on the influence of alloying cobalt with molybdenum for the oxidation of hydrazine in 1 M NaOH aqueous solutions. The electrocatalytic properties of the electrodes are studied by cyclic voltammetry (CV), chronoamperometry (CA), and electrochemical impedance spectroscopy (EIS). Scanning electron microscopy (SEM), X‐ray diffraction (XRD), energy‐dispersive X‐ray spectroscopy (EDS,) and inductively coupled plasma (ICP) analysis demonstrate that the structural features and compositions of the as‐prepared Co–Mo coatings vary with the deposition conditions. Electrochemical characterization indicates that the electrochemical properties and the electrocatalytic activity of the investigated alloys were strongly dependent on the microstructural features obtained under different deposition conditions. The overall experimental data indicate that alloying cobalt with molybdenum metal leads to an increase of the electrocatalytic activity in hydrazine electroxidation compared to when using the pure cobalt electrode. High catalytic efficiencies were achieved on Co/25 at.% Mo and Co/33 at.% Mo electrodes, the latter being the best electrocatalyst for hydrazine electroxidation.     

纳米分子筛LTA包裹Ni-Salen配合物为修饰碳糊电极用于电催化氧化肼反应

采用柔性配体法将Ni-salen配合物包裹在纳米分子筛LTA的超笼中,用来修饰碳糊电极制得Ni(Ⅱ)-SalenA/CPE,并采用循环伏安法、计时电流法和计时库仑法考察了该电极电催化氧化0.1 mol/L NaOH溶液中肼反应性能.首先采用无有机模板剂法合成纳米分子筛LTA,并用各种技术进行了表征.XRD和粒径分析结果分别显示LTA晶体的平均粒径为56.1和72nm.在Ni(Ⅱ)-SalenA/CPE电极氧化还原位上水合肼催化氧化反应电子转移系数为0.64,速率常数为1.03×105cm3/(mol·s).电催化反应机理研究表明,水合肼氧化反应通过它与Ni3+(Salen)O(OH)反应或直接进行电氧化反应.阳极峰电流与扫描速率的平方根呈线性关系,表明反应受扩散控制,水合肼的扩散系数为1.18×10?7cm2/s.结果表明,Ni(Ⅱ)-SalenA/CPE对水合肼氧化反应表现出高的电催化活性,这是由于纳米分子筛LTA的多孔结构以及Ni(Ⅱ)-Salen的存在.最后研究了水合肼在碱性溶液中Ni(Ⅱ)-SalenA/CPE电极上的氧化反应机理,发现其为四电子过程,第一个电子转移反应为速率控制步骤,然后是一个三电子过程,产生环境友好的最终产物氮气和水.     

Poly(thiophene-3-acetic acid)-palladium nanoparticle composite modified electrodes for supersensitive determination of hydrazine

 A promising electrochemical sensor was fabricated by electrodeposition of Pd nanoparticles (PdNPs) on poly(thiophene-3-acetic acid) (PTAA)-modified glassy carbon electrode (GCE), forming a PdNPs/PTAA composites-modified GCE (PdNPs/PTAA/GCE). Scanning electron microscope (SEM) and electrochemical techniques were used for the characterization of these composites. It was found that the PdNPs/PTAA layer was very uniform. Electrochemical experiments showed that this proposed PdNPs/PTAA composites-modified electrode exhibited excellent electrocatalytic activity towards the oxidation of hydrazine. Under the optimum conditions, the proposed sensor can be applied to the quantification of hydrazine with a wide linear range from 8.0?10^-9 mol/L to 1.0?10^-5 mol/L with a low detection limit of 2.67?10^-9 mol/L. The experiment results also showed that the sensor exhibited good reproducibility and long-term stability, as well as high selectivity with no interference from other potential competing species.     

Simultaneous determination of uric acid, xanthine and hypoxanthine at poly(pyrocatechol violet)/functionalized multi-walled carbon nanotubes composite film modified electrode

A sensitive and selective electrochemical method was developed for simultaneous determination of uric acid (UA), xanthine (XA) and hypoxanthine (HX) based on a poly (pyrocatechol violet)/carboxyl functionalized multi-walled carbon nanotubes composite film modified electrode. The preparation and basic electrochemical performance of the novel composite film modified glassy carbon electrode were investigated in details. The electrochemical behaviors of UA, XA and HX at the modified electrode were studied by cyclic voltammetry. The results showed that this new electrochemical sensor exhibited excellent electrocatalytic activity towards the oxidation of the three analytes. The mechanism of catalysis was discussed. The anodic peaks of the three species were well defined with lowered oxidation potential and enhanced oxidation peak currents, so the modified electrode was used for simultaneous voltammetric measurement of UA, XA and HX by differential pulse voltammetry. Under the optimum conditions, the detection limits were 0.16 μmol L(-1) for UA, 0.05 μmol L(-1) for XA and 0.20 μmol L(-1) for HX, respectively (S/N of 3). The proposed method has been successfully applied to simultaneous determination of UA, XA and HX in human serum samples.