Doped colloidal photonic crystal structure with refractive index chirping to the [111] crystallographic axis

A three-dimensionally ordered array of close-packed colloidal spheres, a photonic crystal structure in which the refractive index of the medium interstitial lattice in a colloidal crystal spatially changes in the [111] crystallographic axis, is demonstrated. The colloidal photonic crystal structure with refractive index chirping was produced by infiltration of a monomer and organic dopants with a high refractive index into a silica opal, followed by interfacial gel polymerization. The resulting photonic crystal structure has a gradually varying stop band at each different (111) plane in the face-centered cubic (fcc) crystal structure at a normal incidence. This novel structure exhibited optical characteristics that have band-gap broadening by the superposition of stop bands at each plane of the crystal with different dielectric functions. Moreover, the refractive index perturbation in the [111] fcc opal also showed a defect state within a pseudo-photonic band gap. This new type of photonic crystal structure should be useful for the band-gap engineering of photonic-band-gap materials.     

Direct-write fabrication of colloidal photonic crystal microarrays by ink-jet printing

An array of the colloidal photonic crystals was directly fabricated using an ink-jet printing. The colloidal ink droplets containing the monodispersed polystyrene latex particles were selectively deposited on a hydrophobic surface. Solvent evaporation from each ink droplet leads to a formation of microdome-shaped colloidal assembles of close-packed structures. Microspectroscopic analysis has confirmed that the individual assembly serves as a photonic crystal and its optical properties can be correlated with the microstructural features. Unlike other techniques of patterned growth of colloidal photonic crystal, the substrate does not need to be patterned first and no template is needed in the direct writing by the ink-jet printing. Using our strategy, we have rapidly produced the colloidal photonic crystal microarrays composed of different-sized spheres addressably patterned on the same substrate.     

High-speed fabrication of patterned colloidal photonic structures in centrifugal microfluidic chips

In this paper, we report a rapid and facile method for fabricating colloidal photonic crystals inside microchannels of radially symmetric microfluidic chips which were made using soft-lithography. As the suspension of monodisperse silica or polystyrene latex spheres was driven to flow through the channels under the action of centrifugal force, the colloidal spheres were quickly assembled into face centered cubic arrangement which had a few photonic stop bands. The soft-microfluidic channels and cells confined the colloidal crystals into designed patterns. The optical reflectance was modulated by the refractive-index mismatch between the colloidal particles and the solvent in the interstices between the particles. Therefore, the present microfluidic chips with built-in colloidal photonic crystals can be used as in-situ optofluidic microsensors for high throughput screening or light filters in integrated adaptive optical devices.     

Nonspherical colloidal crystals fabricated by the thermal pressing of colloidal crystal chips

Nonspherical colloids and their ordered arrays may be more attractive in applications such as photonic crystals than their spherical counterparts because of their lower symmetries, although such structures are difficult to achieve. In this letter, we describe the fabrication and characterization of colloidal crystals constructed from nonspherical polyhedrons. We fabricated such nonspherical colloidal crystals by pressing spherical polymer colloidal crystal chips at a temperature slightly lower than the glass-transition temperature (T(g)) of these polymer colloids. During this process, the polymer microspheres were distinctively transformed into polyhedrons according to their crystal structures, whereas the long-range order of the 3D lattice was essentially preserved. Because a working temperature lower than T(g) effectively prevented the colloidal crystals from fusing into films, the spherical colloidal crystals were transformed greatly under pressure, which lead to obvious change in the optical properties of colloidal crystals. Besides their special symmetry and optical properties, these nonspherical colloidal crystals can be used as templates for 2D or 3D structures of special symmetry, such as 2D nano-networks. We anticipate that this fabrication technique for nonspherical colloidal crystals can also be extended to nonspherical porous materials.     

胶体晶体研究进展

重点阐述了有关胶体晶体的制备方法、以胶体晶体为模板制备的大孔材料，以及利用胶体晶体的三维有序结构、结构颜色等特性制备光子晶体、传感器等研究的进展。     

3-D ordered macroporous cuprous oxide: Fabrication, optical, and photoelectrochemical properties

Cuprous oxide 3-D ordered macroporous material was constructed by electrochemical deposition using a polystyrene colloidal crystal as template. The highly ordered macroporous structure with a hexagonal array can be extended over hundreds of square micrometers. The photonic stop bands of both the PS colloidal crystal and Cu2O 3DOM were found. Due to the highly ordered porous structure, the optical absorption and the charge carrier transportation are better in Cu2O 3DOM than in bulk Cu2O, which makes the reduction of oxygen faster on Cu2O 3DOM than on bulk Cu2O under visible light illumination. The higher photocurrent efficiency under visible light illumination makes the 3DOM Cu2O more suitable for solar applications.     

微凝胶胶体晶体研究进展

Poly(N-isopropylacrylamide)(PNIPAM)微凝胶粒子是一种软的胶体粒子.和单分散的SiO_2、PS、PMMA等硬的胶体粒子一样,单分散的PNIPAM微凝胶粒子也可以自组装成为高度有序的胶体晶体.微凝胶粒子软物质的特性及其对外部刺激的响应性赋予其不同于硬球的组装行为.微凝胶胶体晶体的高度有序结构及其刺激响应性使其在诸多领域有重要用途.本文分别介绍了三维及二维微凝胶胶体晶体组装的研究进展,并对已开发的基于微凝胶胶体晶体的应用进行了总结.     

Opal and inverse opal photonic crystals: Fabrication and characterization

Three-dimensional photonic crystals made of close-packed polymethylmethacrylate (PMMA) spheres or air spheres in silica, titania and ceria matrices have been fabricated and characterized using SEM, XRD, Raman spectroscopy and UV–Vis transmittance measurements. The PMMA colloidal crystals (opals) were grown by self-assembly from aqueous suspensions of monodisperse PMMA spheres with diameters between 280 and 415 nm. SEM confirmed the PMMA spheres crystallized uniformly in a face-centred cubic (fcc) array, and UV–Vis measurements show that the colloidal crystals possess pseudo photonic band gaps in the visible and near-IR regions. Inverse opals were prepared by depositing silica (SiO₂), titania (TiO₂) or ceria (CeO₂) in the voids of the PMMA colloidal crystals using sol-gel procedures, then calcining the resulting structure at 550 °C to remove the polymer template. The resulting macroporous materials showed fcc ordering of air spheres separated by thin frameworks of amorphous silica, nanocrystalline titania or nanocrystalline ceria particles, respectively. Optical measurements confirmed the photonic nature of the inverse opal arrays. UV–Vis data collected for the opals and inverse opals obeyed a modified Bragg’s law expression that considers both diffraction and refraction of light by the photonic crystal architectures. The versatility of the colloidal crystal template approach for the fabrication of macroporous oxide structures is demonstrated.     

Templating hydrogels

Templating processes for creating polymerized hydrogels are reviewed. The use of contact photonic crystals and of non-contact colloidal crystalline arrays as templates are described and applications to chemical sensing and device fabrication are illustrated. Emulsion templating is illustrated in the formation of microporous membranes, and templating on reverse emulsions and double emulsions is described. Templating in solutions of macromolecules and micelles is discussed and then various applications of hydrogel templating on surfactant liquid crystalline mesophases are illustrated, including a nanoscale analogue of colloidal crystalline array templating, except that the bead array in this case is a cubic array of nonionic micelles. The use of particles as templates in making core-shell and hollow microgel beads is described, as is the use of membrane pores as another illustration of confinement templating.     

Effects of stretching on microstructures of polymer-immobilized non-close-packed colloidal crystalline array

Non-close-packed silica colloidal crystalline array was immobilized by polymer, and effects of stretching on the change of the optical properties and microstructure of the colloidal crystalline arrays have been demonstrated. The immobilization was a two-step polymerization process: the first step was with hydrophilic polyethylene glycol acrylate (PEGA) polymer gel, and the second step was with 2-hydroxyethyl acrylate polymer matrix. The structure of the three-dimensional array was maintained during the immobilizing process with lock in periodic order. The peak wavelength of Bragg diffraction of the polymer-immobilized colloidal crystalline array shifted to shorter wavelength with stretching. The peak shift was caused by the compression of the polymer proportional to the stretching ratio, and the compression was homogeneous throughout the polymer-immobilized colloidal crystalline arrays. These results show that by using polymer-immobilized non-close-packed colloidal crystalline array, mechanically tunable photonic crystals can be realized, and they open the possibility of tuning the microstructure of colloidal crystalline array for photonic crystal.     

Vapor detection enabled by self-assembled colloidal photonic crystals

Here we report the sensitive and reversible detection of vapors by using self-assembled colloidal photonic crystals. The condensation of various vapors in the interstitials of silica colloidal photonic crystals leads to red-shift and amplitude reduction of optical stop bands. A linear relationship between wavelength shift and vapor partial pressure has been observed for a variety of vapors including ethanol, water, and toluene. Importantly, the sensitivity of colloidal photonic crystal-based vapor detectors can be improved by nearly two orders of magnitude by using a new full-peak analysis technique that takes advantage of the manifest amplitude reduction of optical stop bands during vapor condensation. Optical simulation based on a scalar-wave approximation model shows that the predicted optical responses during vapor condensation in colloidal photonic crystals agree well with experimental results. The condensation of vapors between submicrometer-scale microspheres, a topic that has received little examination, has also been investigated by both experiments and theoretical calculations. Predictions based on a modified Kelvin equation match with the experiments for a wide range of vapor partial pressures.     

胶体晶体自组装排列进展

自组装排列胶体晶体是发展光子晶体等亚微米周期有序结构及新型光电子器件十分重要的环节.高电荷密度单分散胶体球在较弱的离子强度和稀浓度下会自发排列形成紧密堆积的周期性结构(ccp),常常是面心立方(fcc),科学家们以此为基础发展了多种结晶化胶体粒子的方法,包括重力场沉积、电泳沉积、胶体外延技术、垂直沉积、流通池、物理束缚排列及其他的许多方法.目前排列的胶体粒子基本为球形,材料也多为SiO2、PS、PMMA,此外一些复合粒子,主要为核壳粒子的排列这里也稍作介绍,这些方法及其变通的使用可以形成类蛋白石及反蛋白石结构,最终实现光子带隙及其它多种用途。     

Colloidal lithographic nanopatterning via reactive ion etching

We report here a novel colloidal lithographic approach to the fabrication of nonspherical colloidal particle arrays with a long-range order by selective reactive ion etching (RIE) of multilayered spherical colloidal particles. First, layered colloidal crystals with different crystal structures (or orientations) were self-organized onto substrates. Then, during the RIE, the upper layer in the colloidal multilayer acted as a mask for the lower layer and the resulting anisotropic etching created nonspherical particle arrays and new patterns. The new patterns have shapes that are different from the original as a result of the relative shadowing of the RIE process by the top layer and the lower layers. The shape and size of the particles and patterns were dependent on the crystal orientation relative to the etchant flow, the number of colloidal layers, and the RIE conditions. The various colloidal patterns can be used as masks for two-dimensional (2-D) nanopatterns. In addition, the resulting nonspherical particles can be used as novel building blocks for colloidal photonic crystals.     

敏感性有序大孔水凝胶的模板合成与表征

多孔材料由于孔道相互连通、比表面积大等特性而在吸附、离子交换,特别是在催化等领域中具有广泛应用价值．当孔道均匀且有序排列时,如果其间距与可见光波长相匹配时,则可对光产生调制作用,得到光子带隙材料,在未来的信息处理等方面将发挥重要作用．目前,人们以单分散的微粒有序排列的胶体晶为模板制备了各种有序大孔材料,     

梯度结构胶体光子晶体的制备及光子禁带调节

以改进的对流自组装方法制备层数可控的胶体光子晶体, 并通过各向同性氧等离子体(O₂ Plasma)刻蚀构造出梯度结构, 进一步通过金(Au)及无定形硅(Si)的可控沉积调节梯度结构胶体光子晶体的光子禁带, 并将该梯度结构用于罗丹明B的荧光发射增强.     

Tuning the effective width of the optical stop band in colloidal photonic crystals

The optical stop band in colloidal crystals is characterized by the central frequency and bandwidth. Although the former is known to be highly tunable by changing the lattice constant, the latter is basically determined by the refractive index contrast between the particles and the background medium that is intrinsic to the materials. In this study, we show that the effective bandwidth in gelled colloidal crystals can also be tuned by controlling the fabrication conditions. Single-domain gelled colloidal crystals were prepared by photopolymerization under various photoirradiation conditions. It was observed that the width of the stop band in the transmission or reflectance spectrum could be expanded by simply adjusting the irradiation time.     

Tailoring photonic crystals with nanometer-scale precision using polyelectrolyte multilayers

In this paper, we describe a rapid, accurate, and convenient method for postsynthetically tuning the optical properties of colloidal photonic crystals. High quality photonic crystal films are first synthesized and then coated iteratively with layers of water-soluble polyelectrolytes. The coating process results in nanometer-scale shifts in the photonic stop band, a process which has been monitored by theoretical modeling. The results suggest a fundamentally different, reproducible layering mechanism inside the confined spaces of the colloidal crystal where polyelectrolyte multilayers are less densely packed.     

Inward-growing self-assembly of colloidal crystal films on horizontal substrates

Colloidal crystal films have been fabricated on solid substrates with a horizontal deposition method. Scanning electron microscope images showed that the colloidal crystal films exhibit ordered face-centered cubic structures in large domains. Optical measurements demonstrated the presence of photonic band gap along the crystallographic [111] direction. The fabrication method described in this paper allows one to rapidly fabricate colloidal crystal films of different thicknesses, which can be controlled by varying colloidal suspension concentration or volume. In addition, the method also works well for growing colloidal crystal films on a hydrophilic solid substrate with a rough surface. Furthermore, the fabrication of colloidal crystal heterostructures has been demonstrated. An inward-growing mechanism responsible for self-assembly of colloidal spheres on horizontal substrates has been proposed to interpret the observed experimental results.     

Formation of microstructured silicon surfaces by electrochemical etching using colloidal crystal as mask

Silicon disk arrays and silicon pillar arrays with a close-packed configuration having an ordered periodicity were fabricated by the electrochemical etching of a silicon substrate through colloidal crystals used as a mask. The colloidal crystals were directly prepared by the self-assembly of polystyrene particles on a silicon substrate. The transfer of a two-dimensional hexagonal array of colloidal crystals to the silicon substrate could be achieved by the selective electrochemical etching of the exposed silicon surfaces, which were located in interspaces among adjacent particles. The diameter of the tip of the silicon pillars could be controlled easily by changing the anodization conditions, such as current density and period of electrochemical etching.     

Three-dimensional structure and defects in colloidal photonic crystals revealed by tomographic scanning transmission X-ray microscopy

Self-assembled colloidal crystals have attracted major attention because of their potential as low-cost three-dimensional (3D) photonic crystals. Although a high degree of perfection is crucial for the properties of these materials, little is known about their exact structure and internal defects. In this study, we use tomographic scanning transmission X-ray microscopy (STXM) to access the internal structure of self-assembled colloidal photonic crystals with high spatial resolution in three dimensions for the first time. The positions of individual particles of 236 nm in diameter are identified in three dimensions, and the local crystal structure is revealed. Through image analysis, structural defects, such as vacancies and stacking faults, are identified. Tomographic STXM is shown to be an attractive and complementary imaging tool for photonic materials and other strongly absorbing or scattering materials that cannot be characterized by either transmission or scanning electron microscopy or optical nanoscopy.