Enhancement of thermal,mechanical and barrier properties of EVA solar cell encapsulating films by reinforcing with esterified cellulose nanofibres

Solar cell encapsulating film based on ethylene vinyl acetate copolymer (EVA) was modified by using bacterial cellulose (BC) nanofibres. Bacterial cellulose was chemically modified with propionic anhydride prior to compounding with EVA in a twin screw extruder. The effects of fibre content on the mechanical, thermal, optical and barrier properties of the EVA composite films were investigated. Better mechanical and barrier properties of the EVA films were obtained when the modified BC nanofibres were used. The results were ascribed to the different chemical functional groups on the fibre surface, as verified by FTIR spectra. Deacetylation of the EVA was delayed and visible light transparency of the EVA films above 75% was retained. Overall, our study showed that it was possible to improve the barrier properties of EVA film without sacrificing much transparency by using a suitable type and content of cellulose nanofibres.     

Roles of xyloglucan and pectin on the mechanical properties of bacterial cellulose composite films

Xyloglucan and pectin are major non-cellulosic components of most primary plant cell walls. It is believed that xyloglucan and perhaps pectin are functioning as tethers between cellulose microfibrils in the cell walls. In order to understand the role of xyloglucan and pectin in cell wall mechanical properties, model cell wall composites created using Gluconacetobacter xylinus cellulose or cellulose nanowhiskers (CNWs) derived there from with different amounts of xyloglucan and/or pectin have been prepared and measured under extension conditions. Compared with pure CNW films, CNW composites with lower amounts of xyloglucan or pectin did not show significant differences in mechanical behavior. Only when the additives were as high as 60 %, the films exhibited a slightly lower Young’s modulus. However, when cultured with xyloglucan or pectin, the bacterial cellulose (BC) composites produced by G. xylinus showed much lower modulus compared with that of the pure BC films. Xyloglucan was able to further reduce the modulus and extensibility of the film compared to that of pectin. It is proposed that surface coating or tethering of xyloglucan or pectin of cellulose microfibrils does not alone affect the mechanical properties of cell wall materials. The implication from this work is that xyloglucan or pectin alters the mechanical properties of cellulose networks during rather than after the cellulose biosynthesis process, which impacts the nature of the connection between these compounds.     

Development and thermal behaviour of ternary PLA matrix composites

Biodegradable PLA composites were prepared using microcrystalline cellulose (MCC) and silver (Ag) nanoparticles. The main objective of the present study is to develop new biopolymer composites with good mechanical properties, thermal stability, maintaining the optical transparency and also providing antimicrobial properties through silver nanoparticle introduction. Composites were prepared with 1%wt of Ag nanoparticles and 5%wt of MCC using a twin-screw microextruder; film parameters were optimized in order to obtain a thickness range between 20 and 60 μm.PLA composites maintained optical transparency properties of the matrix, while MCC was able to reduce polymer permeability. Thermal analysis revealed that MCC increased PLA crystallinity and the mechanical properties of the composites demonstrated that tensile modulus was improved by microcrystalline cellulose.     

Tensile,thermal, and antibacterial characterization of composites of cellulose/modified Pennisetum purpureum natural fibers with in situ generated copper nanoparticles

Eco-friendly all cellulose composites were developed using cellulose as matrix and nanocomposite (in situ generated copper nanoparticles modified Napier Grass Fibers (NGFs)) as fillers for the antibacterial applications. The content of the nanocomposite filler was increased from 1?wt.% to 5?wt.% in the cellulose matrix. All these composites were characterized by Scanning Electron Microscopy (SEM), Tensile, Thermo Gravimetric Analysis (TGA), and antibacterial tests. SEM-EDX analysis revealed the in situ generation of copper nanoparticles on the surface of the films. Further, all cellulose composites showed good thermal stability. A minimum of 30% increase in char residue was observed in all cellulose nanocomposites compared to matrix. Antibacterial analysis indicated an excellent clear zone formation against both Gram Negative (Escherichia coli) and Gram Positive (Staphylococcus) bacteria. Hence, all these cellulose nanocomposite films can be considered as antibacterial packaging and dressing materials in medical field.     

Multi-layer nanopaper based composites

Native cellulose nanofibrils (CNF) were prepared from bleached birch pulp without any chemical or enzymatic pretreatment. These CNF were modified by adsorption of a small amount of water-soluble polysaccharides and used to prepare nanopapers, which were processed into composites by lamination with an epoxy resin and subsequently cured. The results were compared to the properties of composites prepared using bacterial cellulose nanopapers, since bacterial cellulose constitutes highly pure and crystalline cellulose. It was found that both types of nanopapers significantly improved both the thermal stability and mechanical properties of the epoxy resin. As anticipated, addition of only 2 wt% of water-soluble polysaccharides efficiently hindered crack-propagation within the nanopaper and significantly improved the tensile strength and work of fracture compared to composites containing a conventional nanopaper reinforcement. The mechanical properties of the composites thus reflected the improvement of the nanopaper properties by the polysaccharides. Moreover, it was possible to predict the properties of the final composite from the mechanical performance of the nanopapers.     

Alteration of bacterial nanocellulose structure by in situ modification using polyethylene glycol and carbohydrate additives

Bacterial nanocellulose (BC) is characterized by an exciting interconnection of the important and well-known cellulose properties with the outstanding features of nano-scale materials. As a remarkable benefit of BC the property-controlling fiber network and pore system formed by self-assembly of the cellulose molecules can be modified in situ using additives during biosynthesis. The addition of polyethylene glycol (PEG) 4000 causes a pore size decrease. In presence of β-cyclodextrin or PEG 400 remarkably increased pores can be achieved. Surprisingly, these co-substrates act as removable auxiliaries not incorporated in the BC samples. In contrast, carboxymethyl cellulose and methyl cellulose as additives lead to structural modified composite materials. Using cationic starch (2-hydroxy-3-trimethylammoniumpropyl starch chloride, TMAP starch) double-network BC composites by incorporation of the starch derivative in the BC prepolymer were obtained.     

嵌入式超薄微晶纤维素/碳糊电极的构建及其应用研究

本文以镍铬合金为基体构建了嵌入式超薄微晶纤维素/碳糊电极,该电极是在镍铬合金表面通过直接嵌入微晶纤维素修饰的碳糊膜而制成的。以抗坏血酸为目标物考察其在该电极上的电化学行为,结果表明合金表面嵌入的超薄微晶纤维素/碳糊膜改变了基体电极的电化学性质,扫描电镜表征电极表面形貌,电化学方法考察了该电极对AA的响应。该电极对AA的电氧化显示了良好的增敏作用,可用于实际样品中AA的测定。     

Nanocomposite films based on TEMPO-mediated oxidized bacterial cellulose and chitosan

Nanobacterial cellulose (BC) and chitosan (CH) have similar molecular structures. In the present work, nanocomposite films based on BC and CH were prepared by stepwise modification instead of by conventional physical blending. First, surface C6-carboxylated BC was prepared in a bromide-free system using 2,2,6,6-tetramethylpyperidine-1-oxyl (TEMPO) as a catalyst. The carboxylate groups of oxidised BC could couple to the amine groups of CH. The composite films were characterised by attenuated total reflectance Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and Carbon-13 solid nuclear magnetic resonance ¹³C NMR. The results showed that a cross-linking reaction occurred between TEMPO-mediated oxidised BC and CH. Even in the absence of cross-linkers, these two biopolymers could interact with each other because of their structural similarity. SEM images and tensile tests showed that the TEMPO-oxidized BC and CH composite film prepared at a 0.5:1 ratio was an exception. The mechanical properties of the composite films decreased with increasing CH content, passed through a minimum, and then increased. To explain this phenomenon, we propose that the hydrogen bonding in the original BC microstructure plays a decisive role in the modified nanocomposites. However, BC/CH composites with excellent properties could be synthesised at appropriate reactant ratios.     

Biocomposites of plasticized starch reinforced with cellulose crystallites from cottonseed linter

Environmentally friendly starch biocomposites were successfully developed using a colloidal suspension of cottonseed linter cellulose crystallite as a filler to reinforce glycerol plasticized starch (PS). The cellulose crystallites, having lengths of 350 +/- 70 nm and diameters of 40 +/- 8 nm on average, were prepared from cottonseed linters by acid hydrolysis. The dependence of morphology and properties of the PS-based biocomposites on cellulose crystallites content in the range from 0 to 30 wt.-% was investigated by scanning electron microscopy, differential scanning thermal analysis, dynamic mechanical thermal analysis, and measurements of mechanical properties and water absorption. The results indicate that the strong interactions between fillers and between the filler and PS matrix play a key role in reinforcing the resulting composites. The PS/cellulose crystallite composites, conditioned at 50% relative humidity, undergo an increase in both tensile strength and Young's modulus from 2.5 MPa for PS film to 7.8 MPa and from 36 MPa for PS film to 301 MPa. Further, incorporating cottonseed linter cellulose crystallites into PS matrix leads to an improvement in water resistance for the resulting biocomposites. The mechanical behaviors of the starch-based biocomposites as a function of cellulose crystallites content.     

Renewable resources as reinforcement of polymeric matrices: composites based on phenolic thermosets and chemically modified sisal fibers

Lignocellulosic materials can significantly contribute to the development of composites, since it is possible to chemically and/or physically modify their main components, cellulose, hemicelluloses and lignin. This may result in materials more stable and with more uniform properties. It has previously been shown that chemically modified sisal fibers by ClO(2) oxidation and reaction with FA and PFA presented a thin coating layer of PFA on their surface. FA and PFA were chosen as reagents because these alcohols can be obtained from renewable sources. In the present work, the effects of the polymeric coating layer as coupling agent in phenolic/sisal fibers composites were studied. For a more detailed characterization of the fibers, IGC was used to evaluate the changes that occurred at the sisal fibers surface after the chemical modifications. The dispersive and acid-base properties of untreated and treated sisal fibers surfaces were determined. Biodegradation experiments were also carried out. In a complementary study, another PFA modification was made on sisal fibers, using K2Cr2O(7) as oxidizing agent. In this case the oxidation effects involve mainly the cellulose polymer instead of lignin, as observed when the oxidation was carried out with ClO(2). The SEM images showed that the oxidation of sisal fibers followed by reaction with FA or PFA favored the fiber/phenolic matrix interaction at the interface. However, because the fibers were partially degraded by the chemical treatment, the impact strength of the sisal-reinforced composites decreased. By contrast, the chemical modification of fibers led to an increase of the water diffusion coefficient and to a decrease of the water absorption of the composites reinforced with modified fibers. The latter property is very important for certain applications, such as in the automotive industry.     

High strength modified nanofibrillated cellulose-polyvinyl alcohol films

In this study surface-modified nanofibrillated cellulose (NFC) was used at low levels (0.5 to1.5 wt%) as a reinforcement in a polyvinyl alcohol (PVA) matrix. The modified-NFC–PVA composite films prepared using the solution casting technique showed improved mechanical performance. Birch pulp cellulose was initially modified by allylation using a solvent-free, dry modification method followed by subsequent epoxidation of the allyl groups and finally grinding the pulp to yield epoxy-NFC. In order to obtain optimal mechanical performance, epoxy-NFC with different degrees of substitution was evaluated in the reinforcement of PVA. The addition of 1 wt% epoxy-NFC (degree of substitution, DS 0.07) enhanced the modulus, strength, and strain of pure PVA film by 307, 139 and 23 %, respectively, thus producing the best performing film. The results demonstrate the favourable effect of chemically functionalized NFC on the mechanical properties of polyvinyl alcohol compared to unmodified NFC as reinforcement. In order to improve industrial and economic feasibility, the manufacture of the composite was also done in situ by grinding cellulose directly in PVA to produce the new biocomposite in a one-step process.     

Dispersion evaluation of microcrystalline cellulose/cellulose nanofibril-filled polypropylene composites using thermogravimetric analysis

Microcrystalline cellulose-filled polypropylene (PP) composites and cellulose nanofiber-filled composites were prepared by melt blending. The compounded material was used to evaluate dispersion of cellulose fillers in the polypropylene matrix. Thermogravimetric analysis (TG) and mechanical testing were conducted on composites blended multiple times and the results were compared with single batch melt blended composites. The residual mass, tensile strength, and coefficient of variance values were used to evaluate dispersion of the microcrystalline cellulose fillers in the PP matrix. The potential of using TG to evaluate cellulose nanofiber-filled thermoplastic polymers was also investigated and it was found that the value and variability of residual mass after TG measurements can be a criterion for describing filler dispersion. A probabilistic approach is presented to evaluate the residual mass and tensile strength distribution, and the correlation between those two properties. Both the multiple melt blending and single batch composites manufactured with increased blending times showed improved filler dispersion in terms of variation and reliability of mechanical properties. The relationship between cellulose nanofiber loading and residual mass was in good agreement with the rule of mixtures. In this article, the authors propose to use a novel method for dispersion evaluation of natural fillers in a polymer matrix using TG residual mass analysis. This method can be used along with other techniques such as scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray diffraction (XRD) for filler dispersion evaluation in thermoplastic composites.     

Structure and characteristics of film composites based on methyl cellulose,poviargol, and montmorillonite

The structure of film composites based on methyl cellulose and fillers, such as montmorillonite and silver nanoparticles stabilized by poly(vinylpyrrolidone) (Poviargol), is studied by X-ray diffraction. In the composite, montmorillonite nanoparticles exist in the exfoliated state; when the content of the nanoparticles is below 7 wt %, the crystallinity of methyl cellulose increases. Owing to the presence of the filler and structural ordering of the matrix, elastic characteristics improve and the degradation temperature of the composites increases. The X-ray structural data show that the Ag particles in the methyl cellulose-Poviargol composite are 30 nm in size. The introduction of up to 20 wt % Poviargol assists the crystallization of methyl cellulose. The strength and strain characteristics of the film composites based on methyl cellulose and Poviargol make it possible to use these composites in medicine and agriculture.     

Fabrication of flexible AgNW/cellulose hybrid film with heat preservation and antibacterial properties for agriculture application

In the view of sustainable development and environmental protection, degradable agricultural films with on-demand thermal insulation properties have attracted growing research interest in the last few decades due to the deteriorating environment and extreme climate on the growth and existence of crops. Here, a general strategy has been developed to fabricate degradable silver nanowires modified cellulose (AgNW/cellulose) hybrid film with controllable thermal insulation and antibacterial properties by using plant cellulose and AgNWs as building blocks, PVA and PEG as film forming solvent, as well as their agriculture application. The results show that the AgNWs are evenly dispersed in the three-dimensional grid of cellulose, that they form a film that can withstand a certain tensile force and have good thermal stability. Due to the excellent electrical conductivity, the AgNW/cellulose hybrid films can provide excellent Joule heating, generating rapid thermal response and uniform electrical heating at a low supply voltage of 3 V. In the antibacterial tests against Escherichia coli and Staphylococcus aureus, the AgNW/cellulose hybrid films exhibited large diameters of inhibition zones, revealing the high antibacterial activity. Additionally, the AgNW/cellulose hybrid films showed highly stretchable behavior by delivering a breaking strain of 1.5% with a tensile stress of 0.45 MPa owing to the cross-linked structures of cellulose and AgNWs. Based on the above properties, this study not only provides a potential strategy for the fabrication of flexible and biodegradable agricultural films but also may provide new insights for agricultural thermal management.

     

Osteoconductive biocompatible 3D-printed composites of poly-d,l-lactide filled with nanocrystalline cellulose modified by poly(glutamic acid)

Three dimensional composite matrices based on poly-d,l-lactide filled with 5 or 10 wt% of nanocrystalline cellulose modified by poly(glutamic acid) were produced using pre- optimized 3D printing technique. The composites demonstrated good biocompatibility and significantly improved osteoconductive properties compared with the matrix without filler or the one filled with neat nanocrystalline cellulose.     

Cellulose as matrix component of conducting films

Conjugated polymers gain growing importance as conductive materials in industrial applications in various fields of electronic devices. Cellulose with its extraordinary supramolecular structure and material properties can help to awake the possibilities for conducting polymers in interplay of the two materials. The ability of additional derivatization, the stiff and oriented molecular structure and the inherent strength, stability and film-forming properties give cellulose a complementary role to the brittle conjugated polymers, cellulose imparting the features of a stable and robust carrier component. To go forward this way, making a composite out of cellulose and conducting polymers is a prerequisite. Different strategies to form composite materials of non-derivatized cellulose and conductive organic polymers were tested. Significant differences between various mixing strategies as well as between the conducting polymers polyaniline (PAni), polypyrrole (PPy), and polythiophen (PTh) were observed. In situ synthesis of the conducting polymers in cellulose solutions and microcellulose dispersions as well as blending of pre-synthesized conducting polymers in these cellulose systems were tested. Unexpectedly, not homogenous mixtures showed best results in respect to film formation and conductivity, but composites formed by heterogeneous mixtures of the conducting polymers within a cellulose gel. Best results were obtained with finely dispersed PAni. The results support development studies towards circuitry and photo-current systems based on cellulose carriers.     

Preparation and characterization of cellulose acetate/polysiloxane composites

Composites of cellulose acetate and polysiloxane were prepared using 3-isocyanatepropyltriethoxysilane, as a coupling agent. The structure, the thermal and dynamic-mechanical behaviors, and the morphology of the obtained composites were investigated. The composites showed phase separation which was confirmed by the presence of siloxane micro- and nano-domains dispersed in the cellulose acetate matrix, with good interfacial adhesion between the phases. The results demonstrated that the incorporation of a polysiloxane phase on a cellulose acetate matrix caused a decrease in the glass transition temperature, storage modulus and hardness. The proposed methodology was seen to be convenient for the preparation of cellulose acetate/polysiloxane composites with useful properties.     

Crosslinked fibrous composites based on cellulose nanofibers and collagen with in situ pH induced fibrillation

Collagen and cellulose nanofiber based composites were prepared by solution casting followed by pH induced in situ partial fibrillation of collagen phase and crosslinking of collagen phase using gluteraldehyde. Microscopy studies on the materials confirmed the presence of fibrous collagen and cellulose nanofibers embedded in the collagen matrix. The cellulose nanofiber addition as well as collagen crosslinking showed significant positive impact on the nanocomposite’s mechanical behaviour. The synergistic performance of the nanocomposites indicated stabilization and reinforcement through strong physical entanglement between collagen and cellulose fibres as well as chemical interaction between collagen matrix and collagen fibrils. The mechanical performance and stability in moist conditions showed the potential of these materials as implantable scaffolds in biomedical applications. The collagen-cellulose ratio, crosslinking agent and crosslinking level of collagen may be further optimised to tailor the mechanical properties and cytocompatibility of these composites for specific applications such as artificial ligament or tendon.     

纳米纤维素/聚3,4-乙撑二氧噻吩复合薄膜的制备及电致变色性能

以棉浆粕为原料,采用硫酸溶胀结合超声波处理的方法制备了纳米纤维素(NC).在纳米纤维素的水分散液中加入3,4-乙撑二氧噻吩单体,以过硫酸铵为氧化剂,采用原位化学氧化法制得了纳米纤维素/聚3,4-乙撑二氧噻吩(NC/PEDOT)纳米复合物.对NC和NC/PEDOT复合物进行扫描电镜、透射电镜和红外光谱分析.将纳米复合物的水分散液滴涂在氧化铟锡(ITO)玻璃表面形成复合薄膜,考察不同纳米纤维素含量对NC/PEDOT复合薄膜电致变色性能的影响.结果表明,NC呈棒状,平均直径为20 nm,长度为100~300nm;NC/PEDOT复合物中PEDOT均匀包覆在NC表面形成核壳结构,平均直径为30 nm;复合薄膜中当NC含量为60%时,其电致变色性能最好,具有最高的对比度(24.4%),最短的响应时间(1 s),最高的着色效率(51.8 cm~2/C).     

Morphology control of poly(lactic) acid/polypropylene blend composite by using silanized cellulose fibers extracted from coir fibers

The objective of this work is the use of cellulose fibers extracted from coir fibers as Janus nanocylinders to suppress the phase retraction and coalescence in poly(lactic) acid/polypropylene bio-blend polymers via prompting the selective localization of cellulose fibers at the interface using chemical modification. The untreated and modified cellulose fibers extracted from coir fibers using a silane molecule (tetraethoxysilane) were used as reinforcement and as Janus nanocylinder at two weight contents (2.5 wt% and 5 wt%) to manipulate the morphology of the bio-blends. Their bio-composites with PLA-PP matrix were prepared via melt compounding (at PLA/PP: 50/50). The treatment effect on component interaction and the bio-composites properties have been studied via Scanning electron microscopy, infrared spectroscopy, and differential calorimetry analysis. The mechanical and rheological properties of nanocomposites were similarly assessed. Young's modulus and tensile strength of PLA-PP nanocomposites reinforced by silanized cellulose fibers show a great enhancement as compared to a neat matrix. In particular, there was a gain of 18.5% in Young's modulus and 11.21% in tensile strength for silanized cellulose fiber-based bio-blend composites at 5 wt%. From the rheological point of view, it was found that the silanized cellulose fibers in PLA-PP at both fibers loading enhances the adhesion between both polymers leading to tuning their morphology from sea-island to the continuous structures with the appearance of PLA microfibrillar inside of bio-composites. This change was reflected in the relaxation of the chain mobility of the bio-blend composites.