Kinetics of the polycondensation and copolycondensation of bis(3‐hydroxypropyl) terephthalate and bis(4‐hydroxybutyl) terephthalate

The kinetics of the polycondensation and copolycondensation reactions of bis(3‐hydroxypropyl) terephthalate (BHPT) and bis(4‐hydroxybutyl) terephthalate (BHBT) as monomers were investigated at 270 °C in the presence of titanium tetrabutoxide as a catalyst. BHPT was prepared by the ester interchange reaction of dimethyl terephthalate and 1,3‐propanediol (1,3‐PD). Through the same method adopted for BHPT synthesis, BHBT was prepared with 1,4‐butanediol instead of 1,3‐PD. With second‐order kinetics applied for polycondensation, the rate constants of the polycondensation of BHPT and BHBT, k₁₁ and k₂₂, were calculated to be 4.08 and 4.18 min^?1, respectively. The rate constants of the cross reactions in the copolycondensation of BHPT and BHBT, k₁₂ and k₂₁, were calculated with results obtained from proton nuclear magnetic resonance spectroscopy analysis. The rate constants during the copolycondensation of BHPT and BHBT at 270 °C decreased in the order k₁₂ > k₂₂ > k₁₁ > k₂₁, indicating that the reactivity of BHBT was larger than that of BHPT at 270 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2435–2441, 2002     

Organocatalyzed ring‐opening polymerization of cyclic butylene terephthalate oligomers

In this study, various organic compounds, with different activation modes, have been tested as catalysts for the ring‐opening polymerization (ROP) of cyclic butylene terephthalate oligomers (CBT) in bulk at 210 °C, using tert‐butylbenzyl alcohol (tBnOH) as initiator. Among them, 1,3,5‐triazabicyclo[4.4.0]dec‐5‐ene (TBD) appeared to be the most efficient, achieving high monomer conversions in short reaction times (within minutes). Analysis by size‐exclusion chromatography (SEC) of the poly(butylene terephthalate) (PBT) synthesized using this catalyst also showed that the polymerization follows the expected theoretical M _n trend for molecular weights up to 50 kg·mol^?1. Chain‐end fidelity relatively to the alcohol initiator has been confirmed by MALDI‐TOF mass spectroscopy, which showed that all polymer chains possess the tert‐butylbenzyl moiety as chain‐end. Finally, to demonstrate the potential of this system for the synthesis of PBT‐based block copolymers, a monomethyl ether poly(ethylene glycol) (PEG) of 5000 g·mol^?1 has been employed as initiator for the ROP of CBT. A PEO‐b‐PBT block copolymer of 15,000 g·mol^?1 could thus been obtained, as confirmed by the shift of the SEC traces towards higher molecular weights and the same diffusion coefficient determined for ¹H NMR signals of the PEO block and the PBT block. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1611–1619     

Dodecatungstocobaltate heteropolyanion encapsulation into MIL‐101(Cr) metal–organic framework scaffold provides a highly efficient heterogeneous catalyst for methanolysis of epoxides

A heterogeneous catalyst was synthesized by encapsulation of a Keggin‐type heteropolytungstate, potassium dodecatungstocobaltate trihydrate, K₅[CoW₁₂O₄₀]·(Co‐POM), into chromium(III) terephthalate (MIL‐101). Encapsulation was achieved via a ‘build bottle around ship’ strategy in aqueous media, following a hydrothermal method. The structure of the resulting crystalline solid was characterized using X‐ray diffraction, correlated with Fourier transform infrared and UV–visible spectroscopy. The metal content was analysed using optical emission spectroscopy. Transmission electron microscopy was used to measure particle size and N₂ adsorption in a Brunauer–Emmett–Teller instrument to characterize the specific surface area. The catalytic activity was investigated using methanolysis of epoxides under mild conditions as a test reaction. The turnover frequency of the heterogeneous Co‐POM@MIL‐101 catalyst was more than 20 times higher than that of the homogeneous Co‐POM catalyst. The Co‐POM@MIL‐101 catalyst was reused several times with negligible leaching of Co‐POM and with no considerable loss of its initial efficiency. The simplicity of preparation, extraordinary stability and high reactivity make Co‐POM@MIL‐101 an exceptional catalytic matrix that is easily separable from reaction media.     

Glycolysis of poly(ethylene terephthalate) (PET) using basic ionic liquids as catalysts

The glycolysis of poly(ethylene terephthalate) (PET) was studied using several ionic liquids and basic ionic liquids as catalysts. The basic ionic liquid, 1-butyl-3-methylimidazolium hydroxyl ([Bmim]OH), exhibits higher catalytic activity for the glycolysis of PET, compared with 1-butyl-3-methylimidazolium bicarbonate ([Bmim]HCO₃), 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) and 1-butyl-3-methylimidazolium bromide ([Bmim]Br). FT-IR, ¹H NMR and DSC were used to confirm the main product of glycolysis was bis(2-hydroxyethyl) terephthalate (BHET) monomer. The influences of experimental parameters, such as the amount of catalyst, glycolysis time, reaction temperature, and dosages of ethylene glycol on the conversion of PET, yield of BHET were investigated. The results showed a strong influence of the mixture evolution of temperature and reaction time on depolymerization of PET. Under the optimum conditions of m(PET):m(EG): 1:10, dosage of [Bmim]OH at 0.1 g (5 wt%), reaction temperature 190 °C and time 2 h, the conversion of PET and the yield of BHET were 100% and 71.2% respectively. Balance between the polymerization of BHET and depolymerization of PET could be changed when the reaction time was more than 2 h and contents of catalyst and EG were changed.     

Preparation and catalysis of chloromethylated polystyrene‐supported macrocyclic Schiff base metal complexes for the oxidation of cumene

Chloromethylated polystyrene‐supported macrocyclic Schiff base metal complexes (PS‐L‐M, M = Cu²⁺, Co²⁺, Ni²⁺, and Mn²⁺) were synthesized and characterized by the methods of IR, ICP, and small area X‐ray photoelectron spectroscopy (XPS). The oxidation of cumene by molecular oxygen in the absence of solvent with the synthesized complexes employed as catalyst was carried out. In comparison with their catalytic activities, PS‐L‐Cu is a more effective catalyst for the oxidation of cumene. The main products are 2‐phenyl‐2‐propanol (PP) and cumene hydroperoxide, which were measured by GC/MS. The influences of reaction temperature, the amount of catalyst, as well as the reaction time on the oxidation of cumene were investigated. Copyright © 2008 John Wiley & Sons, Ltd.     

Cobalt Phthalocyanine Immobilized on Graphene Oxide: An Efficient Visible‐Active Catalyst for the Photoreduction of Carbon Dioxide

New graphene oxide (GO)‐tethered–Co^II phthalocyanine complex [CoPc–GO] was synthesized by a stepwise procedure and demonstrated to be an efficient, cost‐effective and recyclable photocatalyst for the reduction of carbon dioxide to produce methanol as the main product. The developed GO‐immobilized CoPc was characterized by X‐ray diffraction (XRD), FTIR, XPS, Raman, diffusion reflection UV/Vis spectroscopy, inductively coupled plasma atomic emission spectroscopy (ICP‐AES), thermogravimetric analysis (TGA), Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). FTIR, XPS, Raman, UV/Vis and ICP‐AES along with elemental analysis data showed that Co^II–Pc complex was successfully grafted on GO. The prepared catalyst was used for the photocatalytic reduction of carbon dioxide by using water as a solvent and triethylamine as the sacrificial donor. Methanol was obtained as the major reaction product along with the formation of minor amount of CO (0.82 %). It was found that GO‐grafted CoPc exhibited higher photocatalytic activity than homogeneous CoPc, as well as GO, and showed good recoverability without significant leaching during the reaction. Quantitative determination of methanol was done by GC flame‐ionization detector (FID), and verification of product was done by NMR spectroscopy. The yield of methanol after 48 h of reaction by using GO–CoPc catalyst in the presence of sacrificial donor triethylamine was found to be 3781.8881 μmol g^?1 cat., and the conversion rate was found to be 78.7893 μmol g^?1cat. h^?1. After the photoreduction experiment, the catalyst was easily recovered by filtration and reused for the subsequent recycling experiment without significant change in the catalytic efficiency.     

Poly(ethylene terephthalate) copolymers containing 5‐nitroisophthalic units. III. Methanolytic degradation

The methanolysis of poly(ethylene terephthalate) (PET) copolymers containing 5‐nitroisophthalic units was investigated. Random copolyesters containing 10 and 30 mol % of such units were prepared via a two‐step melt copolycondensation of bis(2‐hydroxyethyl) terephthalate (BHET) and bis(2‐hydroxyethyl) 5‐nitroisophthalate (BHENI) in the presence of tetrabutyl titanate as a catalyst. First, the susceptibility of these two comonomers toward methanolysis was evaluated, and their reaction rates were estimated with high‐performance liquid chromatography. BHENI appeared to be much more reactive than both BHET and bis(2‐hydroxyethyl) isophthalate. The methanolysis of PET and the copolyesters was carried out at 100 °C, and the degradation process was followed by changes in the weight and viscosity, gel permeation chromatography, differential scanning calorimetry, and ¹H and ¹³C NMR spectroscopy. The copolyesters degraded faster than PET, and the rate of degradation increased with the content of nitrated units. The products resulting from methanolysis were concluded to be dimethyl terephthalate, dimethyl 5‐nitroisophthalate, ethylene glycol, and small, soluble oligomers. For both PET and the copolyesters, an increase in crystallinity was observed during the degradation process, indicating that methanolysis preferentially occurred in the amorphous phase. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 76–87, 2002     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Characterization of Poly(ethyleneoxyethylene terephthalate‐co‐adipate) using NMR Spectroscopy

Comonomer sequence distribution and ¹H‐NMR chemical shifts were determined for poly(ethyleneoxyethylene terephthalate‐co‐adipate) (PEOETA) copolyester. The sequence distribution of terephthalate (T) and adipate (A) residues was found to be random, which is typical for copolyesters synthesized via bulk polycondensation. The inner methylene protons of EOE residues appeared as a pair of doublets due to chemical shift differences among the EOE‐centered dyad sequences TT, TA, AT, and AA. The four equivalent phenylene protons of T residues appeared as a triplet due to chemical shift differences among the T‐centered triad sequences TTT, TTA (?ATA), and ATA. Higher‐order tetrad and pentad sensitivity were also observed for the inner methylene and phenylene protons, respectively, especially for TT‐ and TTT‐centered sequences. The sequence sensitivity of the phenylene protons was attributed to unique spatial interactions between themselves and protons within adjacent adipate and EOE units. These spatial interactions were confirmed using Nuclear Overhauser Enhancement Spectroscopy (NOESY).     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Copper(I) complex of 1,3‐DimethylBarbituric acid modified SBA‐15 and its catalytic role for the synthesis of 2,3‐Dihydroquinazolin‐4(1H)‐ones and Imidazoles

An efficient one‐pot method for synthesis of 2,3‐dihydroquinazolin‐4(1H)‐ones and tri/tetra substituted‐1H‐imidazoles has been accomplished in the presence of catalytic amounts of Cu(I)‐1,3‐dimethylbarbituric acid modified SBA‐15 as heterogeneous catalyst with good to excellent yields. The catalyst is reusable and can be applied several times without any decrease in product yield. The synthesized catalyst was characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD), energy dispersive X‐ray spectroscopy (EDS), thermal gravimetric analysis (TGA), N₂ adsorption/desorption isotherms (BET), Fourier transform infrared spectroscopy (FT‐IR) and atomic absorption spectroscopy (AAS).     

Poly(ethylene terephthalate) copolymers containing 5‐nitroisophthalic units. I. Synthesis and characterization

Poly(ethylene terephthalate‐co‐5‐nitroisophthalate) copolymers, abbreviated as PETNI, were synthesized via a two‐step melt copolycondensation of bis(2‐hydroxyethyl) terephthalate and bis(2‐hydroxyethyl) 5‐nitroisophthalate mixtures with molar ratios of these two comonomers varying from 95/5 to 50/50. Polymerization reactions were carried out at temperatures between 200 and 270 °C in the presence of tetrabutyl titanate as a catalyst. The copolyesters were characterized by solution viscosity, GPC, FTIR, and NMR spectroscopy. They were found to be random copolymers and to have a comonomer composition in accordance with that used in the corresponding feed. The copolyesters became less crystalline and showed a steady decay in the melting temperature as the content in 5‐nitroisophthalic units increased. They all showed glass‐transition temperatures superior to that of PET with the maximum value at 85 °C being observed for the 50/50 composition. PETNI copolyesters appeared stable up to 300 °C and thermal degradation was found to occur in two well‐differentiated steps. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1934–1942, 2000     

Axial base‐controlled catalytic activity,oxidative stability and product selectivity of water‐insoluble manganese and iron porphyrins for oxidation of styrenes in water under green conditions

A series of water‐insoluble iron(III) and manganese(III) porphyrins, FeT(2‐CH₃)PPCl, FeT(4‐OCH₃)PPCl, FeT(2‐Cl)PPCl, FeTPPCl, MnT(2‐CH₃)PPOAc, MnT(4‐OCH₃)PPOAc, MnT(2‐Cl)PPOAc and MnTPPOAc, in the presence of imidazole (ImH), F^?, Cl^?, Br^? and acetate were used as catalysts for the aqueous‐phase heterogeneous oxidation of styrenes to the corresponding epoxides and aldehydes with sodium periodate. Also, the effect of various reaction parameters such as reaction time, molar ratio of catalyst to axial base, type of axial base, molar ratio of olefin to oxidant and nature of metal centre on the activity and oxidative stability of the catalysts and the product selectivity was investigated. Higher catalytic activities were found for the iron complexes. Interestingly, the selectivity towards the formation of epoxide and aldehyde (or acetophenone) was significantly influenced by the type of axial base. Furthermore, Br^? and ImH were found to be the most efficient co‐catalysts for the oxidation of olefins performed in the presence of the manganese and iron porphyrins, respectively. The optimized molar ratio of catalyst to axial base was different for various axial bases. Also, the order of co‐catalyst activity of the axial bases obtained in aqueous medium was different from that reported for organic solvents. The use of a convenient axial base under optimum reaction catalyst to co‐catalyst molar ratio in the presence of the manganese porphyrin gave the oxidative products with a conversion of ca 100% in a reaction time of less than 3 h. However, the catalytic activity of the iron porphyrins could not be effectively improved by increasing the catalyst to co‐catalyst molar ratio.     

Transesterification of Ethylene Carbonate with Dimethyl Terephthalate over Various Metal Acetate Catalysts

IntroductionDimethyl carbonate(DMC) is known to be a novelbuilding block in organic synthesis. As an environmen-tally benign compound and a unique intermediate,DMC has attracted much attention[1,2]. Among the va-rious methods for synthesizing DMC, the tra…     

Synthesis and Characterization of Poly（butylene adipate-co-terephthalate） Catalyzed by Rare Earth Stearates

Rare earth （Nd, Y, La, Dy） stearates have been synthesized and used as single component catalysts for the polycondensation of dimethyl terephthalate, adipic acid and 1,4-butanediol for the first time preparing biodegradable poly（butylene adipate-co-terephthalate） （PBAT） with high molecular weight, The microstructures of PBAT were characterized by ^1H NMR spectra. The PBAT exhibits good mechanical properties such as high tensile strength （ca. 20 MPa） and long break elongation （〉700%）.     

Bifunctional Heterogeneous Catalysis of Silica–Alumina‐Supported Tertiary Amines with Controlled Acid–Base Interactions for Efficient 1,4‐Addition Reactions

We report the first tunable bifunctional surface of silica–alumina‐supported tertiary amines (SA–NEt₂) active for catalytic 1,4‐addition reactions of nitroalkanes and thiols to electron‐deficient alkenes. The 1,4‐addition reaction of nitroalkanes to electron‐deficient alkenes is one of the most useful carbon–carbon bond‐forming reactions and applicable toward a wide range of organic syntheses. The reaction between nitroethane and methyl vinyl ketone scarcely proceeded with either SA or homogeneous amines, and a mixture of SA and amines showed very low catalytic activity. In addition, undesirable side reactions occurred in the case of a strong base like sodium ethoxide employed as a catalytic reagent. Only the present SA‐supported amine (SA–NEt₂) catalyst enabled selective formation of a double‐alkylated product without promotions of side reactions such as an intramolecular cyclization reaction. The heterogeneous SA–NEt₂ catalyst was easily recovered from the reaction mixture by simple filtration and reusable with retention of its catalytic activity and selectivity. Furthermore, the SA–NEt₂ catalyst system was applicable to the addition reaction of other nitroalkanes and thiols to various electron‐deficient alkenes. The solid‐state magic‐angle spinning (MAS) NMR spectroscopic analyses, including variable‐contact‐time ¹³C cross‐polarization (CP)/MAS NMR spectroscopy, revealed that acid–base interactions between surface acid sites and immobilized amines can be controlled by pretreatment of SA at different temperatures. The catalytic activities for these addition reactions were strongly affected by the surface acid–base interactions.     

Synthesis and characterization of polyvinylpyrrolidone immobilized on magnetic nanoparticles modified by ionic liquid as a novel and recyclable catalyst for the three‐component synthesis of amidoalkyl naphthols

In this study, an efficient and green procedure is explained for the preparation of 1‐amidoalkyl‐2‐naphthols applying one‐pot condensation reaction of 2‐naphthol, amide and aromatic nanoparticles (Fe₃O₄@SiO₂@IL‐PVP) as a novel solid acid catalyst under solvent‐free conditions. The remarkable features of this method are short reaction time, high conversions, and high yield of product, easy workup procedures and solvent‐free conditions. The Fe₃O₄@SiO₂@IL‐PVP catalyst was characterized via Fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction patterns (XRD), scanning electron microscopy (SEM), Transmission electron microscopy (TEM), thermal gravimetric analysis (TGA), vibrating sample magnetometer (VSM), and energy‐dispersive X‐ray spectroscopy (EDS). Also, nanocatalysts could be easily recovered by a simple magnet and reused for the next reactions without significant loss of its catalytic activity.     

Cu(II) immobilized on mesoporous organosilica as an efficient and reusable nanocatalyst for one‐pot Biginelli reaction under solvent‐free conditions

Cu(II) immobilized on mesoporous organosilica nanoparticles (Cu²⁺@MSNs‐(CO₂^?)₂) has been synthesized, as a inorganic–organic nanohybrid catalyst, through a post‐grafting approach. Its characterization is carried out by Fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Energy dispersive X‐ray (EDX), Thermogravimetric/differential thermal analyses (TGA‐DTA), and Nitrogen adsorption–desorption analysis. Cu²⁺@MSNs‐(CO₂^?)₂ exhibits high catalytic activity in the Biginelli reaction for the synthesis of a diverse range of 3, 4‐dihydropyrimidin‐2(1H)‐ones, under mild conditions. The anchored Cu(II) could not leach out from the surface of the mesoporous catalyst during the reaction and it has been reused several times without appreciable loss in its catalytic activity.     

Polysiloxane microspheres functionalized with imidazole groups as a palladium catalyst support

Polysiloxane microspheres containing a large number of silanol groups were obtained by an emulsion process of modified polyhydromethylsiloxane. N‐substituted imidazole groups were grafted on these microspheres by the silylation of their silanol groups with N‐[γ‐(dimethylchlorosilyl)propyl]imidazole hydrochloride. The progress of the reaction was monitored using ²⁹Si and ¹³C magic angle spinning (MAS) NMR and its impact on microsphere morphology was studied using scanning electron microscopy (SEM). The usefulness of the imidazole‐functionalized microspheres as a support for a metal catalyst was demonstrated by their reaction with PdCl₂(PhCN)₂. In this way a new heterogenized catalyst, Pd(II) complex with imidazole ligands supported on polysiloxane microspheres, was generated. This catalyst, MPd , was characterized using ¹³C and ²⁹Si MAS NMR, X‐ray photoelectron, Fourier transform infrared and far‐infrared spectroscopies, X‐ray diffraction, SEM–energy‐dispersive X‐ray spectroscopy and wide‐angle X‐ray scattering. The catalyst appears in two structures, as Pd(II) complex and Pd(0) nanoclusters. Its catalytic activity was tested using a model reaction, the hydrogenation of cinnamaldehyde, and compared with that of an analogous complex operating in a homogeneous system. MPd showed a high activity in the promotion of hydrogenation of cinnamaldehyde. The activity in the substrate conversion was stable at least in five cycles of this reaction. The main product was hydrocinnamaldehyde which could be obtained with a yield above 70%. A mechanism of the reaction is proposed. Copyright © 2016 John Wiley & Sons, Ltd.     

Poly(ethylene terephthalate) copolymers containing 5‐nitroisophthalic units. II. Crystallization studies

The microstructure and crystallization behavior of a set of poly(ethylene terephthalate‐co‐5‐nitroisophthalate) copolymers (PETNI) containing 5‐nitroisophthalic units in the 10–50 mol % range were examined and compared to those of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐isophthalate) (PETI) copolymers. A ¹³C NMR analysis of PETNI copolymers in a trifluoroacetic acid solution indicates that they are random copolymers with average sequence lengths in accordance with ideal polycondensation statistics. Differential scanning calorimetry (DSC) studies show that PETNI containing 5‐nitroisophthalic units up to 20 mol % are able to crystallize and that crystallization takes place in these copolymers at much slower rates than in PET. Wide‐angle X‐ray diffraction from powder and fibers reveals that crystallizable PETNI adopts the same triclinic crystal structure as PET, with the nitroisophthalate units being excluded from crystallites. Fourier transform infrared in combination with cross‐polarization/magic‐angle spinning ¹³C NMR spectroscopy demonstrates the occurrence of a gauche–trans conversion encompassing the crystallization process. A correlation between DSC and spectroscopic data leads us to conclude that the content of trans conformer in the noncrystallized phase of PETNI is higher than in both PET and PETI copolymers and suggests that secondary crystallization in the homopolymer must proceed by a mechanism different than that in copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1553–1564, 2001