Monitoring of phenylurea and propanil herbicides in river water by solid-phase-extraction high performance liquid chromatography with photoinduced-fluorimetric detection

The separation and determination of five herbicides, including propanil and the phenylureas diuron, isoproturon, linuron and neburon, has been performed by an HPLC method, using photochemically-induced fluorescence detection. The non-fluorescent herbicides were transformed into fluorescent compounds by post-column photochemical reaction. A 60:40 (v/v) acetonitrile-buffer solution of potassium phosphate dibasic (pH 7, 0.01 M) was used for the chromatographic elution to separate propanil, linuron and neburon. The overlapping of isoproturon and diuron peaks, in the selected conditions, was resolved by changing the initial movil phase composition to 50:50 (v/v) methanol-buffer solution of potassium phosphate dibasic (pH 7, 0.01 M). The procedure was applied with satisfactory results to the analysis of these herbicides in Guadiana river water samples (Badajoz, Spain), allowing the detection of herbicide residues in the order of mug l(-1), by using a solid-phase extraction (SPE) pre-concentration step.     

Rapid and sensitive determination of phenylurea herbicides in water in the presence of their anilines by extraction with a Carbopack cartridge followed by liquid chromatography

A rapid and sensitive method for determining phenylurea herbicides in environmental aqueous samples in the presence of their anilines is described. The water sample is preconcentrated by passage at a flow-rate of ca. 150 ml/min through a 250-mg graphitized carbon black (Carbopack B) cartridge. After washing with 0.6 ml of methanol, the Carbopack B trap is connected with a cartridge containing a strong cation exchanger. Organics trapped by the Carbopack cartridge are eluted by passage of 6 ml of methylene chloride-methanol (95:5, v/v). Anilines and other basic compounds are quantitatively subtracted from the solvent system while flowing through the cation-exchange cartridge. After evaporation and redissolution, the sample is subjected to reversed-phase gradient elution high-performance liquid chromatography with UV detection at 250 nm. Recoveries of phenylureas added to water at levels between 30 and 3000 ng/l were higher than 92%. The limit of detection was about 1 ng/l, for a 2-1 sample. With respect to an octadecyl (C18)-bonded silica cartridge, the Carbopack B cartridge had a far better extraction efficiency for polar phenylureas.     

Ultra-pressure liquid chromatography-electrospray tandem mass spectrometry for multiresidue determination of pesticides in water

A multiresidue analysis method has been developed for the determination of pesticides in water by ultra-performance liquid chromatography (UPLC) combined with tandem mass spectrometry (MS/MS). The selected pesticides represent a broad range of polarity and volatility [benzoylcyclohexanedione (mesotrione and sulcotrione); chloroacetamide (acetochlor, alachlor, dimethenamide, and metolachlor); phenoxyacetic acid (2,4-D and MCPA); phenoxypropionic (dichloprop and mecoprop); phenylurea (chlortoluron, diuron, isoproturon, linuron, and metoxuron); sulfonylurea (foramsulfuron, iodosulfuron, and nicolsulfuron); triazine (atrazine, cyanazine, desethylatrazine (DEA), desisopropylatrazine (DIA), simazine, and terbutylazine)]. The analytes were extracted using solid-phase extraction (SPE). The separation was carried out on an acquity UPLC BEH C18 column (1.7 microm, 50 mm x 1 mm ID) using a gradient elution profile and mobile phase consisting of 0.1% formic acid in water and acetonitrile. The pesticides were detected with a tandem mass spectrometer after being ionised positively or negatively (depending on the molecule) using an electrospray ionisation (ESI) source. To achieve the suitable extraction conditions for sample preparation, several parameters affecting the efficiency of SPE such as the nature of the sorbent and the eluent, extractant volume and pH were studied. The best recovery was obtained by the extraction with an Oasis HLB cartridge and 3 mL of a solution of acetonitrile/dichloromethane (1:1, v/v) at pH 2. The average recoveries of the pesticides in different samples ranged from 82 to 109%. The weight least squares (WLS) linear regression was used to calculate the limits of detection and quantification (LOD and LOQ) because the dispersion was heteroskedastic. All the pesticides could be correctly quantified at a concentration level of 50 ng L(-1) and most of them could be detected at a concentration inferior or equal to 8 ng L(-1). Efficiency and robustness of this method were evaluated by the analysis of several samples of real natural water.     

The role of organic colloids in herbicide transfer to rivers: a quantitative study of triazine and phenylurea interactions with colloids

For moderately hydrophobic compounds such as most pesticides adsorption on colloids (<0.2 microm) may play a key role in pesticide mobility as well as in their degradation by chemical and microbiological processes. However, until now, pesticide-organic colloid interactions are poorly understood. Quantitative data for sorption equilibria on colloids of two series of herbicides including triazines (atrazine, simazine, terbutylazine, prometryne, desethylatrazine, and desisopropylatrazine) and phenylureas (isoproturon, linuron, neburon, and diuron) sampled in the Seine river (urban zone) and the Marne river (agricultural zone) are presented. Partition coefficient of herbicides on colloids (K(com)), were evaluated by solid-phase extraction coupled with high-performance liquid chromatography-UV diode-array detection (SPE-HPLC-UV/DAD). In the case of triazines a satisfactory log-log correlation was found between K(com) and octanol-water coefficient (K(ow)) values. Phenylureas did not obey this correlation, with K(com) values being about two times higher than those of triazines. The existence of two distinct types of adsorption behaviour on colloids partly explains the different occurrence of triazines and phenylureas in surface waters.     

Part-per-trillion level determination of antifouling pesticides and their byproducts in seawater samples by off-line solid-phase extraction followed by high-performance liquid chromatography-atmospheric pressure chemical ionization mass spectrometry

A new method for the simultaneous determination of antifouling pesticides and some of their byproducts such as dichlofluanid, diuron and its byproducts [demethyldiuron and 1-(3,4-dichlorophenyl)urea], (2-thiocyanomethylthio)ben: zothiazole, chlorothalonil, Sea-nine 211, Irgarol 1051 and one of its byproducts (2-methylthio-4-tert.-butylamino-s-triazine) in seawater was developed. The extraction of these compounds from the filtered seawater samples was performed off-line with different solid-phase extraction sorbents using (I) a 500 mg graphitized carbon black cartridge (ENVI-Carb) and (II) 200 mg polymeric cartridges (LiChrolut EN and Isolute ENV+) and passing 500 ml of the sample through these cartridges. The detection was carried out by reversed-phase high-performance liquid chromatography coupled with atmospheric pressure chemical ionization mass spectrometry both in the negative and positive ion modes. The recovery ranged from 76 to 96% for the whole antifouling group with the ENVI-Carb cartridges and the detection limit was at the part-per-trillion level except for TCMTB. The method utilizing the polymeric cartridge proved to be very useful, time saving and with good recoveries when only Irgarol and its byproduct, Sea-nine 211 and diuron and its byproducts, have to be analyzed. The different cartridges were applied to the analysis of these pesticides in different marinas of the Catalan coast; diuron, dichlofluanid, Sea-nine 211, Irgarol as well as demethyldiuron and the Irgarol byproduct being the must ubiquitous pollutants. Maximum concentration levels were 2-3.5 microg/l of diuron and Sea-nine 211, respectively.     

Analysis of trace levels of pesticides in rainwater by SPME and GC-tandem mass spectrometry after derivatisation with PFFBr

Solid-phase microextraction (SPME) was used for the analysis of some pesticides (bromoxynil, chlorotoluron, diuron, isoproturon, 2,4-MCPA, MCPP and 2,4-D) in rainwater after derivatisation with PFBBr and gas chromatography-ion trap mass spectrometry. The derivatisation procedure was optimized by testing different methods: direct derivatisation in the aqueous phase followed by SPME extraction, on-fibre derivatisation and derivatisation in the injector. The best result was obtained by headspace coating the PDMS/DVB fibre with PFBBr for 10 min followed by direct SPME extraction for 60 min at 68 °C (pH 2 and 75% NaCl). Good detection limits were obtained for all the compounds: these ranged between 10 and 1,000 ng L⁻¹ with a relatively high uncertainty due to the combination of derivatisation and SPME extraction steps. The optimized procedure was applied to the analysis of pesticides in rainwater and results obtained shows that this method is a fast and simple technique to assess the spatial and temporal variations of concentrations of pesticides in rainwater.     

Immunoaffinity-based extraction of phenylurea herbicides using mixed antibodies against isoproturon and chlortoluron

Summary The analysis of several phenylurea herbicides in different waters is described using an immunoaffinity column clean-up and determination by high performance liquid chromatography. The pesticides were selectively retained on a solid phase extraction column containing antibodies to chlortoluron and to isoproturon immobilised onto silica. Selected phenylureas were eluted using a simple phosphate buffered saline/ethanol mixture at low pH. The immunoaffinity approach gave extracts free of interfering substances and allowed detection limits comparable to those required for pesticides in water in the European Community. The proposed method was successfully applied to the determination of chlortoluron, isoproturon, linuron and chlorbromuron in tap and river water. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

High-performance liquid chromatography column switching applied to the trace determination of herbicides in environmental and drinking water samples

A selective and sensitive coupled-column high-performance liquid chromatographic method is developed for the simultaneous determination of 5 phenylurea herbicides (monuron, linuron, isoproturon, monolinuron, and diuron) in environmental and drinking water samples. Sample clean-up is performed automatically by means of a column switching technique. Using 2 octadecyl silica columns connected via two programmable 6-port valves and ultraviolet detection at 244 nm, the aforementioned compounds can be determined at the low concentration levels required for pesticide residue analysis in water samples. A mobile phase consisting of a mixture of methanol-water (55:45, v/v) is pumped at 1 mL/min. For the 5 phenylureas, high recoveries ranging from 94.9 to 101.6%, good reproducibility with relative standard deviations lower than 5%, and wide linear ranges up to 20 micrograms/L are observed with determination limits of 0.05 microgram/L. The method is successfully applied to the screening of different environmental water samples such as surface, ground, rain, and drinking water.     

Multi-Residue Analysis of Some Polar Pesticides in Water Samples with SPE and LC–MS–MS

In the present study a multi-residue analytical method was developed for monitoring some polar pesticides such as acephate, methamidophos, carbofuran, isoproturon, dimethoate in water with SPE (solid-phase extraction) and LC–MS–MS. Acetochlor was taken as surrogate, and alachlor as internal standard. SPE with different types of columns was compared with LLE (liquid-liquid extraction). Further, the breakthrough volume for different pesticides was determined. The results showed that the selected pesticides can be determined very sensitively with LC–MS–MS. The minimum detectable quantity (MDQ) for each pesticide was about 1.0 ng. To date, SPE cartridge studies showed that the Oasis HLB cartridges were suitable for further studies. However, for Oasis HLB cartridge, different pesticide showed different breakthrough volume. The results showed that for acephate and methamidophos, the breakthrough volume was about 30 mL of water sample, much less than the breakthrough volume of other pesticides studied. Because of the higher vapor pressure and higher Henry's constant of methamidophos, dimethoate and carbofuran, much attention should be paid on their losses in the evaporation step of the experiment. This analytical method can be applied to determine pesticide contamination in environmental water samples. Revised: 12 September 2005 and 21 October 2005     

Trace analysis of herbicides in wastewaters by a dispersive liquid–liquid microextraction approach and liquid chromatography with quadrupole linear ion trap mass spectrometry: Evaluation of green parameters

An analytical method for determining phenylureas (monuron, isoproturon, diuron, linuron and neburon) and propanil herbicides in wastewater has been developed and validated, and the most significant parameters were compared with the corresponding ones found in the literature, thus showing the method performance. The method involves pre‐concentration by a simple, rapid, sensitive and low environmental toxicity temperature‐controlled ionic liquid dispersive liquid–liquid microextraction procedure. The herbicides were identified and determined by liquid chromatography with a hybrid triple quadrupole linear ion trap mass spectrometer. Data acquisition in selected‐reaction monitoring mode allowed the simultaneous identification and quantification of the analytes using two transitions. The information dependent acquisition scan was performed to carry out the identification of those analytes whose second transition was present at low intensity, also providing extra confirmation for the other analytes. Limits of quantification were in the range 1.0–5.0 ng/L. Good recoveries (95–103%) were obtained for the extraction of the target analytes in wastewater samples. The methodology developed was applied to analyze effluent wastewater samples from a wastewater treatment plant located in an agricultural zone of Almería (Spain) and the results indicated the presence of diuron at mean concentration levels of 73.5 ng/L.     

One step carbon nanotubes-based solid-phase extraction for the gas chromatographic–mass spectrometric multiclass pesticide control in virgin olive oils

This article presents a novel application of carbon nanotubes for the determination of pesticides (chlortoluron, diuron, atrazine, simazine, terbuthylazin-desethyl, dimetoathe, malathion and parathion) in virgin olive oil samples. For this purpose, two carbon nanotubes, multi-walled and carboxylated single-walled, were evaluated, the later being the most appropriate for the aim of the work. The sorbent (30 mg) was packed in 3-mL commercial cartridge and the virgin olive oil samples diluted (20%, v/v) in hexane were passed through it. After a washing step with 3 mL of hexane to remove the sample matrix, the pesticides were eluted with 500 μL of ethyl acetate. In order to achieve lower detection limits, the eluent was evaporated under a nitrogen stream and the residue reconstituted in 50 μL of the same solvent. Aliquots of 2 μL of the extract were directly injected into the GC–MS system for analysis. The low limits of detection achieved, between 1.5 and 3.0 μg L⁻¹, permit the application of the method to control the presence of these pollutants in very restrictive samples such as the ecological virgin olive oil. In addition to the sensitivity enhancement, the solid-phase extraction procedure is rather simple as it involves a single preconcentration–elution step, which allows sample processing in less than 8 min. Moreover, the cartridge can be reused at least 100 times without losing performance. The method was applied to the determination of the pesticides in two monovarietal and one ecologic commercial extra virgin olive oil samples. Two pesticides were detected in each of the monovarietal virgin olive oils while the ecological sample resulted to be a pesticide-free one.     

Determination of some pesticides and intermediates by ion chromatography

The present paper deals with a method of solid-phase extraction of tocopherol acetate (TA, 49.6 microg/g) from emulsified nutritional supplements, which contains 50 kinds of compounds, followed by high-performance liquid chromatography (HPLC) with fluorescence detection The TA concentration is 5 to approximately 100,000 times lower than that of other compounds in the samples. Measuring the loading capacity of the larger amounts of vegetable oil onto the Bond Elut C18 cartridge was examined for the complete retention of smaller level of TA. A sample solution was applied to a solid-phase extraction cartridge and then TA was eluted by acetonitrile followed by HPLC. This method was suitable for the determination of TA in emulsified nutritional supplements. The proposed method was simple, rapid (analysis time: ca. 15 min), sensitive [detection limit: ca. 0.1 ng per injection (100 microl) at a signal-to-noise ratio of 3:1], and reproducible (relative standard deviation: ca. 2.5% (n=5)). The calibration graph of TA was linear in the range of 0.1 to 100 ng per injection (100 microl). Recovery of TA was over 90% by the standard addition method.     

An interlaboratory study to evaluate potential matrix reference materials for herbicides in water

Matrix reference materials (MRM) are essential tools for the validation of analytical protocols. Nowadays, there are no such materials for the determination of herbicides in water. Pesticides stored in acetonitrile and stored on solid phase extraction (SPE) cartridges previously percolated with a water sample spiked with triazines and phenylureas have proven to be good candidates for reference materials because of their satisfactory stability under appropriate temperature conditions. To evaluate the behaviors of these materials containing pesticides and to be analyzed by liquid chromatography, a collaborative study including 15 laboratories has been organized. Observed reproducibility on candidate materials after the removal of extreme results was 16.1% for the vials with pesticides in acetonitrile (at around 0.125 mg/L) directly analyzed, 29.2% for a water sample spiked with the pesticides (at around 0.5 microg/L) analyzed after preconcentration on a cartridge and 26.7% for the cartridges previously percolated with a water containing the pesticides (250 mL at around 0.5 microg/L for each pesticide) analyzed after elution. Such dispersion values are quite compatible with the requirement of a further certification for such materials.     

Solid-Phase Extraction and LC with Fluorescence Detection for Analysis of PAHs in Rainwater

The efficiency of extraction of polycyclic aromatic hydrocarbons (PAHs) from rainwater by solid-phase extraction (SPE) with three different types of cartridge, and analysis by high-performance liquid chromatography with fluorescence detection, are discussed in this paper. Three cartridges were investigated but only one was suitable. After equilibration in a desiccator for 65–80 h or in ambient air for 90–100 h the SPE cartridges were activated with 5 mL dichloromethane then 5 mL 2-propanol. The volume of sample passed through the cartridges was 50 mL; after loading of the sample the cartridges were dried under vacuum for approximately 20 min by application of a pressure of 15 mbar to the SPE manifold. The PAHs were eluted with 5 mL dichloromethane–hexane, 50:50 (v/v). The flow rate used for conditioning, sample loading, and elution was 2.5 mL min⁻¹, achieved by application of a pressure of 6 mbar. For analysis of PAHs in rainwater, recovery was between 67 and 99%, the relative standard deviation varied between 2 and 5%, and the detection limits of the method were less than 16.9 ng L⁻¹ for several PAHs. These optimum conditions were used for analysis of rainwater collected between June 2002 and May 2003 at two sites in Alsace (eastern France) and 17 PAHs were quantitatively determined. Concentrations varied between 1.6 and 968.1 ng L⁻¹.     

MWCNTs-solid phase extraction combined with ultra-high performance liquid chromatography-tandem mass spectrometry for the determination of eleven organophosphorus pesticides in river water

A method for simultaneous determination of 11 organophosphorus pesticides residues in river water by MWCNTs-solid phase extraction combined with ultra-high performance liquid chromatography/tandem mass spectrometry was developed. After centrifugation and filtration, the target pesticides were enriched with MWCNTs-SPE cartridge. Then the pesticides adsorbed on MWCNTs were eluted with ethyl acetate and dichloromethane, the eluent was dried-up under nitrogen flow and the residue was dissolved in methanol-water (1:1, v/v) as sample solution. The separation was accomplished on a C18 column with the mobile phase consisting of methanol and 0.1% formic acid at 0.20 mL/min in gradient elution. The pesticides were detected in multiple reaction monitoring mode by a triple quadruple mass spectrometer. Good linearities were obtained within 1–200 ng/L, with the correlation coefficients greater than 0.998. The detection and quantification limits were in the ranges of 0.02–1.00 ng/L and 0.07–3.33 ng/L, respectively. The recoveries and relative standard deviations were in the range of 88.3–124.9% and 0.12–20.5%, respectively. The method has been successfully applied to the detection of 34 urban river water samples from Chengdu, China and 7 organophosphorus pesticides were detected with the concentrations of 0.32–211 ng/L.     

Capillary liquid chromatography with off-line mid-IR and Raman micro-spectroscopic detection: analysis of chlorinated pesticides at ppb levels

A flow-through microdispenser was used as a solvent elimination interface, allowing vibrational spectroscopic detection in capillary liquid chromatography in addition to standard UV detection. Using a flow-through microdispenser, robust and stable deposition of picoliter-sized droplets on a CaF₂ plate window was achieved. The CaF₂ window was placed on a thermostated sample holder (80 °C) mounted on a computerized x, y stage for achieving fast solvent evaporation and enabling recording of the chromatogram as a trace of deposited material. The dried residues that were formed had diameters of a few tens of micrometers and were analysed by mid-IR and Raman micro-spectroscopy. Conditions were optimized for high sensitivity of measurement and maintaining chromatographic resolution during the deposition step. Due to the destruction-free character of Raman and FTIR spectroscopy, these techniques could be applied sequentially to interrogate the same deposits. To test the usefulness of the methodology for environmental analysis, the determination and unambiguous identification of chlorinated pesticides (chlortoluron, diuron, atrazine, and terbuthylazine) in river water was used as an example, obtaining limits of identification of 2 ng analyte on-column and precision of approximately 10% RSD. The application of the developed method to spiked real river samples demonstrated the identification power of the proposed method as, in addition to the four previously studied pesticides, two additional pesticides (simazine and isoproturon) could also be detected and identified.     

Use of on-line liquid chromatography-nuclear magnetic resonance spectroscopy for the rapid investigation of flavonoids from Sorocea bomplandii

A HPLC method, using photochemically-induced fluorescence detection, is described for the separation and determination of four phenylurea herbicides including diuron, isoproturon, linuron and neburon. A post-column photoreactor, consisting of a reactor knitted around a 4 W xenon lamp, has been included between the column and the detector, in order to transform the non-fluorescent herbicides into fluorophors. The influence of mobile phase composition, flow-rate, pH, and buffer concentration has been studied. An acetonitrile–buffer solution of potassium phosphate dibasic of pH 7 and 0.01 M concentration (60:40, v/v), was selected as optimum. For the fluorimetric detection, optimal excitation/emission wavelengths 324/403, 301/433, 335/411 and 326/385 nm were selected for the determination of diuron, isoproturon, linuron and neburon, respectively. The detection limits ranged between 0.07 and 0.46 μg/ml, according to the compound.     

Gas chromatographic behaviour of urea herbicides

Summary Gas chromatographic conditions for determining eight phenylurea (chlortoluron, diuron, fluometuron, isoproturon, linuron, metabenzthiazuron, metobromuron and monuron) and one sulfonylurea (chlorsulfuron) herbicides were assessed. Degradation products of the herbicides formed in the injector were used for identification. Most phenylureas formed their respective carbamic acid methyl esters, metabenzthiazuron formed an aminobenzothiazol and chlorsulfuron formed an aminotriazine plus a phenylsulfonamide. On-column injection of standards using a BP10 capillary column was evaluated to identify the chromatographic behaviour. Detection limits ranged from 0.05 ng for chlorsulfuron to 3 ng for monuron with the NPD and, from 0.01 ng for chlorsulfuron to 5 ng for metabenzthiazuron with the ECD. The RSDs (n=4) were lower than 4% at the 12–25 ng level. The method was applied to the analysis of surface waters extracted with C18 Empore disks with recoveries higher than 85%. Each herbicide could be determined in water down to 0.1 μg·L⁻¹. Chlortoluron was found (11.4 μg·L⁻¹) in a water sample and its presence was confimed by gas chromatography-mass spectrometry.     

Determination of vitamin D2 in emulsified nutritional supplements by solid-phase extraction and column-switching high-performance liquid chromatography with UV detection

This paper deals with a method for solid-phase extraction of trace amounts of vitamin D2 (VD2, 19 ng/g) from emulsified nutritional supplements, which contain 50 kinds of compounds, followed by column-switching high-performance liquid chromatography (HPLC) with UV detection at 265 nm. VD2 is present at 1000-20,000,000 times lower concentration than other components. Bond Elut C18 cartridge was chosen as for the emulsified nutritional supplements after comparison with eight other types. A sample solution was applied to the solid-phase extraction cartridge and VD2 was eluted by methanol followed by HPLC. The effects of sample pH, eluent composition and eluate volume on the retention and elution of VD2 on Bond Elut C18 cartridge were examined. The resulting method was simple, rapid (analysis time: approximately 20 min), sensitive (detection limit: approximately 0.1 ng per injection (200 microl) at a signal-to-noise ratio 3:1), and reproducible (relative standard deviation: approximately 6.2%, n=5). The calibration graph for VD2 was linear in the range of 0.1-3 ng per injection (200 microl). Recovery of VD2 was approximately 80% by the standard addition method.     

多壁纳米碳管固相萃取测定水中的有机氯农药

对于水样中的有机氯农药的净化方法主要是采用传统的液液分配的方法,缺点是溶剂使用量和前处理复杂。近年来固相萃取及固相微萃取等技术被应用到水样中的有机污染物的测定。如利用键合在硅胶上的非极性(C18,LC18等)或极性物质(LC-CN,LC-NH2)对水中有机物进行富集,用GDX或XAD自填的固相柱的报道也很多。纳米技术和纳米材料的发展为开发固相萃取材料带来新契机。纳米材料是指尺寸大小在从1～100m之间物质。与普通的块体材料相比,纳米材料具有较大的比表面,因而有可能具有较大吸附容量。纳米材料在环境有机污染物分离富集方面的应用研究才刚刚开始。本文主要就纳米碳管对水样中的有机氯农药进行研究,优化固相萃取条件。