Changes During Storage of Electrically Conductive Blends Polyaniline–Poly(Ethylene‐co‐vinyl Acetate)

Abstract

The electrical conductivity behavior of polyaniline–poly(ethylene‐co‐vinyl acetate) (PANI–EVA) blends was variable and dynamic during their storage. It was shown that the apparent concentration of the intrinsically conductive polymer at which a conductivity jump of the blends occurs (Φ _c ) is not a constant value over time. The electrical conductivity of the films of low PANI content (below 2.5 wt.%) increased by several (ca. 5) orders of magnitude. It was found that the PANI phase undergoes a flocculation process subsequently resulting in the formation of conductive pathways and a continuous network. Besides, the shape of percolation curves was found to change during storage of the films. Decreased conductivity deviations were registered for blends of low PANI content (<2.5 wt.%), indicating that an improvement (or decreasing number of defects) of the conductive pathways took place within the bulk of the insulating EVA matrix. These results and observed phenomena are discussed by means of the interfacial model for electrically conductive polymer blends. They supported the dispersion/flocculation phase transition within similar composite materials. The phase separation and conductivity jump are attributed to the interfacial interactions between the polymeric constituents. It was shown that the microstructure of the blends consists of highly ordered PANI paths embedded in the insulating EVA matrix. Long fibrils of PANI and interconnected fractal‐like networks were observed. It was found that the sizes of the PANI domains also varied during storage of the films. Due to the spontaneous flocculation of the primary PANI particles, conductive pathways are formed at extremely low percolation threshold (Φ _c , loading level ca. 5 × 10^?3 wt. fraction). Thus, an important property of the conductive constituent, namely its solid‐state rearrangement, was proved. This PANI self‐organization is also interpreted according to the interfacial model of polymer composites. On the other hand, the competition between self‐organization of the complex of PANI with dodecylbenzenesulfonic acid and crystallization of EVA matrix has resulted in structural changes and formation of continuous conductive networks within the blends, responsible for their significantly increased conductivity.     

ELECTROACTIVE AND NANOSTRUCTURED POLYMERS AS SCAFFOLD MATERIALS FOR NEURONAL AND CARDIAC TISSUE ENGINEERING

Conducting polymer, polyaniline （PANI）, has been studied as a novel electroactive and electrically conductive material for tissue engineering applications. The biocompatibility of the conductive polymer can be improved by （i） covalently grafting various adhesive peptides onto the surface of prefabricated conducting polymer films or into the polymer structures during the synthesis, （ii） co-electrospinning or blending with natural proteins to form conducting nanofibers or films, and （iii） preparing conducting polymers using biopolymers, such as collagen, as templates. In this paper, we mainly describe and review the approaches of covalently attaching oligopeptides to PANI and electrospinning PANI-gelatin blend nanofibers. The employment of such modified conducting polymers as substrates for enhanced cell attachment, proliferation and differentiation has been investigated with neuronal PC-12 cells and H9c2 cardiac myoblasts. For the electrospun PANI- gelatin fibers, depending on the concentrations of PANI, H9c2 cells initially displayed different morphologies on the fibrous substrates, but after one week all cultures reached confluence of similar densities and morphologies. Furthermore, we observed, that conductive PANI, when maintained in an aqueous physiologic environment, retained a significant level of electrical conductivity for at least 100 h, even though this conductivity was decreasing over time. Preliminary data show that the application of micro-current stimulates the differentiation of PC-12 cells. All the results demonstrate the potential for using PANI as an electroactive polymer in the culture of excitable cells and open the possibility of using this material as an electroactive scaffold for cardiac and/or neuronal tissue engineering applications that require biocompatibility of conductive polymers.     

Influence of graphene reinforcement in conductive polymer: Synthesis and characterization

Lightweight conductive polymers are considered for lightning strike mitigation in composites by synthesizing intrinsically conductive polymers (ICPs) and by the inclusion of conductive fillers in insulating matrices. Conductive films based on polyaniline (PANI) and graphene have been developed to improve through‐thickness conductivity of polymer composites. The result shows that the conductivity of PANI enhanced by blending polyvinylpyrrolidone (PVP) and PANI in 3:1 ratio. Conductive composite thin films are prepared by dispersing graphene in PANI. The conductivity of composite films was found to increase by 40× at 20 wt% of graphene inclusion compared with PVP and PANI blend. Fourier‐transform‐infrared (FTIR) spectra confirmed in situ polymerization of the polymer blend. The inclusion of graphene also exhibits an increase in Tg by 21°C. Graphene additions also showed an increase in thermal stability by approximately 148°C in the composite films. The mechanical result obtained from DMA shows that inclusion of graphene increases the tensile strength by 48% at 20 wt% of graphene reinforcement. A thin, highly conductive surface that is compatible with a composite resin system can enhance the surface conductivity of composites, improving its lightning strike mitigation capabilities.     

Preparation of polyaniline grafted multiwalled carbon nanotubes and conductive application in polyetherimide

A methodology for improving antistatic property of polyetherimide (PEI) composite using polyaniline (PANI) grafted multi‐walled carbon nanotubes (MWNTs) as conductive medium was proposed. First, the MWNTs grafted with PANI (PANI‐g‐MWNTs) were prepared by in‐situ polymerization in an emulsion system. Subsequently, PANI‐g‐MWNTs were blended with PEI using N‐methyl‐2‐pyrrolidone as solvent. After removing the solvent, the PEI/PANI‐g‐MWNT composite was prepared. As assisted conductive medium, the grafted PANI molecular chains on MWNT surface were dispersed in the PEI matrix to decrease the percolation value of the antistatic composites. The structure and morphology of PANI‐g‐MWNTs were characterized by Fourier transform infrared spectroscopy, transmission electron microscope, thermogravimetric analysis, and X‐ray powder diffraction, respectively. The dispersion of PANI‐g‐MWNTs in PEI matrix was studied by scanning electron microscope. The electrical performance was characterized by highly resistant meter. The volume resistivity of the conductivity percolation threshold was 1.781 × 10^?8 S/cm when the loading of PANI‐g‐MWNTs was 1.0 wt%. The conductivity of PANI‐g‐MWNTs/PEI composites was found to be higher than that of pristine MWNTs/PEI composite. Copyright © 2012 John Wiley & Sons, Ltd.     

FERROFLUID CONTAINING SOLUBLE CONDUCTIVE POLYANILINE AND ITS FREESTANDING FILMS

Ferrofluid containing highly conductive polyaniline (PANI) was prepared, in which soluble PANI solutions dopedwith 10-camphorsulfonic acid (CSA) and dodecyl benzenesulfonic acid (DBSA) were used as the basic solution and Fe_3O_4nanoparticles (d = 10 nm) as the magnetic material. Moreover, the freestanding films of the resulting ferrofluid can beobtained by an evaporation method. The electrical and magnetic properties of the ferrofluid or its films can be adjustedthrough changing the content of PANI and Fe_3O_4. High saturated magnetization (≈ 30 emu/g) and high conductivity(≈ 250 S/cm) of the composite films can be achieved when the composite film contains 26.6 wt% of Fe_3O_4. In particular, itwas found that the composite films exhibit a super-paramagnetic behavior (Hc = 0) attributed to the size of Fe_3O_4 particles on the nanometer scale.     

Conductivity and structure of melt‐processed polyaniline binary and ternary blends

In the present study, conductive binary and ternary blends containing polyaniline (PANI) were developed through melt blending. The binary blends' investigation focused on the morphology, in light of the components' interaction, and the resulting electrical conductivity. Similar solubility parameters of a given doped PANI and a matrix polymer lead to dispersion of fine PANI particles within the matrix, and to formation of conducting paths at low PANI contents. A plasticizer acting also as a compatibilizer improves the matrix polymer/PANI interactions. In ternary blends consisting of PANI and two immiscible polymers, the PANI preferrentially locates in one of the components, affecting the blend's morphology. This “concentrating” effect leads to relatively high electrical conductivity at a low PANI content. The electrical conductivity of the studied ternary blends is almost independent of the components' sequence of addition into the hot melt mixing device, exhibiting the selectivity of PANI towards one of the components. Copyright © 2000 John Wiley & Sons, Ltd.     

Effect of polyaniline (PANI) on Poly(vinylidene fluoride-co-hexaflouro propylene) (PVDF-co-HFP) polymer electrolyte membrane prepared by breath figure method

Poly(vinylidene fluoride-co-hexaflouro propylene) is a well-known material for polymer electrolyte membranes (PEMs) due to its low cost, high mechanical integrity and excellent chemical resistance; however, its pure form has limited characteristics that require further modification to achieve optimum results. Therefore, the different dosages of polyaniline (PANI) (10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt%) were incorporated into PVDF-HFP blend to fabricate PVDF-HFP/PANI polymer electrolyte membrane by using breath-figure method. The FTIR peaks of PVDF-HFP and PVDF-HFP/PANI membrane confirms the successful incorporation of PANI into PVDF-HFP blend, while TGA, DSC and XRD analysis shows the PANI effect on stability and ionic conductivity of PVDF-HFP membrane. The PVDF-HFP/PANI membrane with 30 wt% PANI found superior with the highest porosity of 83%, electrolyte uptake of 270% and ionic conductivity of 1.96 mS cm⁻¹; however, the other concentrations of PANI were also effective and enhanced the performance of PVDF-HFP membrane. This shows the improved performances of PVDF-HFP membrane were attributed to successful incorporation of PANI and the proposed membrane can be a suitable alternative PEM or a separator for energy devices.     

A new route to obtain PVDF/PANI conducting blends

Electrically conductive poly(vinylidene fluoride)(PVDF) - polyaniline blends of different composition were synthesized by chemical polymerization of aniline in a mixture of PVDF and dimethylformamide (DMF) and studied by electrical conductivity measurement, UV-Vis-NIR and FTIR spectroscopy. The samples were obtained as flexible films by pressing the powder at 180 °C for 5 min. The electrical conductivity showed a great dependence on the syntheses parameters. The higher value of the electrical conductivity was obtained for the oxidant/aniline molar ratio equal to 1 and p-toluenesulfonic acid-TSA/aniline ratio between 3 and 6. UV-Vis-NIR and FTIR spectra of the blend are similar to the doped PANI, indicating that the PANI is responsible for the high electrical conductivity of the blend. The electrical conductivity of blend proved to be stable as a function of temperature decreasing about one order at temperature of 100 °C. The route used to obtain the polymer blend showed to be a suitable alternative in order to obtain PVDF/PANI-TSA blends with high electrical conductivity.     

Ag+掺杂聚苯胺的制备及其电容特性研究

以苯胺为单体,采用界面聚合法合成了不同浓度的Ag⁺掺杂的聚苯胺(PANI/Ag⁺),使用傅里叶变换红外光谱（FT-IR）、X射线衍射（XRD）和场发射扫描电镜（SEM）等手段对其结构和形貌进行了分析和表征. 在0.5 mol•L^-1 Na₂SO₄电解液中,通过循环伏安（CV）、恒流充放电（CP）以及电化学阻抗（EIS）等技术研究了其电化学性能. 结果表明,当电流密度为5 mA•cm^-2时,PANI/0.12mol•L^-1 Ag⁺的比电容达529 F•g^-1,循环1000次后比电容保持51%,相对于无Ag⁺掺杂的PANI,表现出更优良的电化学电容特性.     

Carbon nanotube-polyaniline hybrid materials

A hybrid material of carbon nanotubes (CNTs)-polyaniline (PANI) was prepared by in situ emulsion polymerization. The structural characterization showed that some CNTs were linked up by PANI chains, which appears to be like a network including PANI fiber and nanotubes. This network results in the hybrid material having highly conductivity with new conductive passageway. The conductivity and thermal properties of hybrid materials depend on the content of CNTs. The CNTs do not affect the structure of PANI chains.     

Polyaniline-coated coconut fibers: Structure,properties and their use as conductive additives in matrix of polyurethane derived from castor oil

Electrically conducting fibers based on coconut fibers (CF) and polyaniline (PANI) were prepared through in situ oxidative polymerization of aniline (ANI) in the presence of CF using iron (III) chloride hexahydrate (FeCl_3.6H₂O) or ammonium persulfate (APS) as an oxidant. The PANI-coated coconut fibers (CF-PANI) displayed various morphologies, electrical conductivities and percentages of PANI on the CF surface. For both systems, a PANI conductive layer was present on the CF surface, which was responsible for an electrical conductivity of around 1.5 × 10⁻¹ and 1.9 × 10⁻² S cm⁻¹ for composites prepared with FeCl₃.6H₂O and APS, respectively; values that are similar to that of pure PANI. In order to modify the structure and properties of polyurethane derived from castor oil (PU) both CF-PANI and pure PANI were used as conductive additives. The PU/CF-PANI composites exhibited higher electrical conductivity than pure PU and PU/PANI blends. Additionally, the PU/CF-PANI composites showed a variation in electrical resistivity according to the compressive stress applied, indicating that these materials could be applied for pressure-sensitive applications.     

Segregated network polymer/carbon nanotubes composites

In this work we present the preparation of conductive polyethylene/carbon nanotube composites based on the segregated network concept. Attention has been focused on the effect of decreasing the amount of filler necessary to achieve low resistivity. Using high- and low-grade single-walled carbon nanotube materials we obtained conductive composites with a low percolation threshold of 0.5 wt.% for high-grade nanotubes, about 1 wt% for commercial nanotubes and 1.5 wt% for low-grade material. The higher percolation threshold for low-grade material is related to low effectiveness of other carbon fractions in the network formation. The electrical conductivity was measured as a function of the single-walled carbon nanotubes content in the polymer matrix and as a function of temperature. It was also found that processing parameters significantly influenced the electrical conductivity of the composites. Raman spectroscopy was applied to study single wall nanotubes in the conductive composites.     

A novel approach for preparation of conductive hybrid elastomeric nano‐composites

Since the discovery of carbon nanotubes (CNTs) and intrinsically conductive polymers, such as polyaniline (PANI) some research has focused on the development of novel hybrid materials by combining CNT and PANI to achieve their complementary properties. Electrically conductive elastomer nano‐composites containing CNT and PANI are described in the present investigation. The synthesis procedure includes in‐situ inverse emulsion polymerization of aniline doped with dodecylbenzene sulfonic acid in the presence of CNT and dissolved styrene‐isoprene‐styrene (SIS) block copolymer, followed by a precipitation–filtration step. The synthesis step is carried out under ultrasonication. The resulting uniform SIS/CNT/PANI dispersions are stable for long time durations. The incorporation of CNT/PANI in the SIS elastomeric matrix improves thermal, mechanical and electrical properties of the nano‐composites. The formation of continuous three‐dimensional CNT/PANI network, assumed to be responsible for enhancement of the resulting nano‐composite properties, is observed by HRSEM. A relatively low percolation threshold of 0.4 wt.% CNT was determined. The Young's modulus of the SIS/CNT/PANI significantly increases in the presence of CNT. High electrical conductivity levels were obtained in the ternary component systems. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Polyaniline/Partially Phosphorylated Poly（vinyl alcohol） Nanoparticles

The polyaniline/partially phosphorylated poly（vinyl alcohol）（PANI/P-PVA） nanoparticles were prepared by the chemical oxidative dispersion polymerization of aniline monomer in 0.5 mol/L HC1 aqueous media with the partially phosphorylated poly（vinyl alcohol） （P-PVA） as the stabilizer and co-dopant. The PANI/P-PVA nanoparticles were characterized by transmission electron microscopy （TEM）, Fourier transform infrared spectroscopy （FTIR）, thermal gravimetric analysis （TGA）, X-ray diffraction （XRD）, electrical conductivity measurements and re-dispersion stability testing. All the results were compared with the properties of the conventional polyaniline in the emeraldine salt form （PANI ES）. It was found that the feeding ratio of P-PVA obviously affected the morphology, re-dispersion stability and electrical conductivity of the PANI/P-PVA nanoparticles. When the feeding ratio of P-PVA ranged from 40 wt% to 50 wt%, the PANI/P-PVA nanoparticles showed spherical shape with good uniformity, significant re-dispersion stability in aqueous media and good electrical conductivity.     

Ageing of Conductive Polyaniline/Poly(Ethylene-co-Vinylacetate) Composites Studied by Thermal Methods

The long-term environmental ageing of conductive composite films containing ethylene-co-vinyl-acetate (EVA) copolymer and a complex of polyaniline (PANI) and dodecylbenzenesulfonic acid (DBSA) was studied by using differential scanning calorimetry (DSC). We assume that both phase separation and crosslinking of PANI main chains occur in the systems. On the other hand, the competition between PANI–DBSA complex self-organization and crystallization of EVA matrix result in structural changes and formation of continuous conductive network, responsible for significantly increased (ca five orders of magnitude) electrical conductivity of the aged films. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis and characterization of conductive polyaniline/TiO2 composite nanofibers

Fibrillar conductive polyaniline/TiO₂ (PANI/TiO₂) nanocomposites with different TiO₂ amount were synthesized with a template-free in situ polymerization method and characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and conductivity measurement. The morphology determination shows that the PANI/TiO₂ composite nanofibers are relatively uniform with the diameter and length in the range of 20–40 nm and 390–420 nm respectively. It also shows that the TiO₂ of the composite is rutile crystalline and PANI has some degree of crystallinity. The IR measurement indicates that there is a strong interaction between the PANI and TiO₂ nanoparticles, and it has a beneficial effect on the thermal stability of the composite nanofiber. The conductivity of PANI/TiO₂ composites changes with TiO₂ amount and reaches an optimum value of 2.86 S/cm at 11.1 wt% TiO₂. Translated from Journal of Northwest Normal University (Natural Science), 2006, 42(4): 67–70 (in Chinese)     

Postsynthetic-Modified PANI/MOF Composites with Tunable Thermoelectric and Photoelectric Properties

A 3D Co-based metal–organic framework ( Co-MOF ) with two kinds of large pores filled by free Co²⁺ ions and ligands was synthesized and characterized. To expand the MOF structure and conductivity, the free Co²⁺ ions and ligands were exchanged by conductive ionic liquid EtpyBr and photosensitive AgNO₃ through single crystal-to-single crystal transformation, which produced structure-changed 3D MOFs Co-MOF-Br and Co-Ag-MOF , which were characterized by single-crystal X-ray diffraction. Incorporating small quantities of doped polyaniline (PANI) with redox activity into the pores could further tune the stability and conductivity of the three MOFs. The PANI/MOFs all show outstanding electrical conductivity (≈10⁻² S cm⁻¹), and PANI/ Co-MOF-Br has the largest p-type Seebeck coefficient of 66.6 μV K⁻¹. PANI/ Co-MOF-Br and PANI/ Co-Ag-MOF have 4 and 15 times higher photocurrent density compared with PANI/ Co-MOF , respectively. This work sheds light on the design of advanced electrically conductive 3D MOFs.     

A New Strong-Acid Free Route to Produce Xanthan Gum-PANI Composite Scaffold Supporting Bioelectricity

Conductive hybrid xanthan gum (XG)–polyaniline (PANI) biocomposites forming 3D structures able to mimic electrical biological functions are synthesized by a strong-acid free medium. In situ aniline oxidative chemical polymerizations are performed in XG water dispersions to produce stable XG–PANI pseudoplastic fluids. XG–PANI composites with 3D architectures are obtained by subsequent freeze-drying processes. The morphological investigation highlights the formation of porous structures; UV–vis and Raman spectroscopy characterizations assess the chemical structure of the produced composites. I–V measurements evidence electrical conductivity of the samples, while electrochemical analyses point out their capability to respond to electric stimuli with electron and ion exchanges in physiological-like environment. Trial tests on prostate cancer cells evaluate biocompatibility of the XG–PANI composite. Obtained results demonstrate that a strong acid-free route produces an electrically conductive and electrochemically active XG–PANI polymer composite. The investigation of charge transport and transfer, as well as of biocompatibility properties of composite materials produced in aqueous environments, brings new perspective for exploitation of such materials in biomedical applications. In particular, the developed strategy can be used to realize biomaterials working as scaffolds that require electrical stimulations for inducing cell growth and communication or for biosignals monitoring and analysis.     

Synthesis and characterization of polyaniline/silicon dioxide composites and preparation of conductive films

The focus of this study was to synthesize the inherently conductive polymer polyaniline using an optimized process to prepare polyaniline/silicon dioxide (PANI/SiO₂) composites by in situ polymerization and ex situ solution mixing. PANI and PANI/SiO₂ composite films were prepared by drop‐by‐drop and spin coating methods. The electrical conductivities of HCl doped PANI film and PANI/SiO₂ composite films were measured according to the standard four‐point‐probe technique. The composite films exhibited an increase in electrical conductivity over neat PANI. PANI and PANI/SiO₂ composites were also investigated by spectroscopic methods including UV‐Vis, FT‐IR, and Photoluminescence. UV‐Vis and FT‐IR studies showed that SiO₂ particles affect the quinoid units along the polymer backbone and indicate strong interactions between the SiO₂ particles and the quinoidal sites of PANI (doping effect). The photoluminescence properties of PANI and PANI/SiO₂ composites were studied and the PANI/SiO₂ composites showed increased intensity as compared to neat PANI. The increase of conductivity of PANI/SiO₂ composite may be partially due to the doping or impurity effect of SiO₂ where the silicon dioxides compete with chloride ions. The morphology of particles and films were examined by a scanning electron microscope (SEM). SEM measurements indicated that the SiO₂ were well dispersed and isolated in composite films. Copyright © 2009 John Wiley & Sons, Ltd.     

Chemical and electrochemical grafting of polyaniline onto poly(vinyl chloride): synthesis,characterization, and materials properties

We have designed and developed a new strategy for the chemical and electrochemical graft copolymerization of aniline onto poly(vinyl chloride). For this purpose, first phenylamine groups were incorporated into poly(vinyl chloride) via a nucleophilic substitution reaction in the presence of a solvent composed of 4‐aminophenol, potassium carbonate, and dry N,N‐dimethylformamide at room temperature, in order to avoid cross‐linking. The macromonomer obtained was used in chemical and electrochemical oxidation copolymerization with aniline monomer to yield a poly(vinyl chloride)‐g‐polyaniline (PVC‐g‐PANI) graft copolymer. The chemical structures of samples as representatives were characterized by means of Fourier transform infrared and ¹H nuclear magnetic resonance spectroscopies. The electroactivity behaviors of the synthesized samples were verified under cyclic voltammetric conditions. The electrical conductivity and electroactivity measurements showed that the PVC‐g‐PANI graft copolymer has lower electrical conductivity as well as electroactivity than those of the pure PANI. However, the lower electrical conductivity and electroactivity levels in this material can be improved at the price of solubility and processability. Moreover, the thermal behavior and chemical composition of the synthesized graft copolymer were investigated. Copyright © 2016 John Wiley & Sons, Ltd.