Crystallization and equilibrium melting behavior of PBT/PETG blends

The results of studies of equilibrium melting point and crystallization behavior of PBT/PETG blends are reported for the first time. A single composition‐dependent glass‐transition temperature is observed in the DSC studies. The isothermal crystallization studies of the blends indicate retardation in crystallization rate as evidenced by the increase in crystallization half time. The retardation in crystallization rate has been attributed to the miscibility in the molten state and the hindrance to the diffusion of crystallizable units. This assumption is further supported by the composition dependence of the crystallization half time. A composition‐dependent melting point depression has been observed which has been attributed to the possible thermodynamic and morphological effects. The interaction parameter calculated by analyzing equilibrium melting point depression shows composition‐dependent negative values confirming the miscibility of the systems. These results are in good agreement with our earlier results on mechanical and dynamic mechanical properties of PBT/PETG blends. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2439–2444, 1999     

Phase behavior and properties of polyvinyl alcohol/gelatin blends with novel pH‐dependence

A novel change of phase behavior and properties of polyvinyl alcohol (PVA)/gelatin blends as a function of pH was reported. The PVA/gelatin blends were found to be completely miscible in acidic condition (pH < 4), partially miscible in basic condition (pH > 8), and immiscible in neutral condition (pH was ca. 6). As a result, the membranes cast from acidic condition showed the highest tensile strength and the lowest alcohol vapor permeation (AVP) rate; those obtained from neutral condition showed the lowest tensile strength and highest AVP rate; the properties of membranes cast from basic condition lay in between. The interaction between PVA and gelatin was investigated via Fourier transform infrared spectrum (FTIR), differential scanning calorimetry (DSC), and Zetasizer measurement. The novel pH‐dependence of the blends was ascribed to the protonation of amino groups of gelatin in acidic condition, which resulted in a strong electrostatic attraction between ? NH of gelatin and ? OH of PVA. The partial miscibility in basic condition was due to the ionization of carboxyl groups of gelatin, which caused a stretching of gelatin via electrostatic repulsive force and a breakage of the H‐bonding among the molecular chains, leading to a limited interaction between PVA and gelatin and forming a partially miscible blend. In neutral conditions, there were almost no charges (very limited protonation and ionization) at the weak polyampholyte gelatin, and the strong H‐bonding among gelatin molecules themselves or PVA molecules themselves caused the phase separation between gelatin and PVA. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 239–247, 2009     

Barrier property enhancement of polyamide 6 by blending with a polyhydroxyamino‐ether resin

In this work, the transport properties of the system formed by polyamide 6 (PA6) and polyhydroxyamino‐ether resin (PHAE) have been studied after characterizing the miscibility behavior. A single glass transition has been observed using differential scanning calorimetry that usually means total miscibility, but measurements by solid‐state cross‐polarization magic angle spinning NMR have shown that this system is only partially miscible, in good agreement with phase behavior reported before. Both carbon dioxide and water vapor transport properties of PA6/PHAE blends have been measured. For both penetrants, permeability coefficient shows an interesting negative deviation from the additive value, even the barrier character to carbon dioxide of pure PHAE is maintained up to 60 % in PA6 composition. Besides, PHAE reduces the plasticization effect of water in PA6. These improvements are very interesting for the PA 6 due to its wide use in packaging applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1625–1634, 2009     

Reactive compatibilization of polyamide‐6 (PA 6)/polybutylene terephthalate (PBT) blends by a multifunctional epoxy resin

A multifunctional epoxy resin has been demonstrated to be an efficient reactive compatibilizer for the incompatible and immiscible blends of polyamide‐6 (PA 6) and polybutylene terephthalate (PBT). The torque measurements give indirect evidence that the reaction between PA and PBT with epoxy has an opportunity to produce an in situ formed copolymer, which can be as an effective compatibilizer to reduce and suppress the size of the disperse phase, and to greatly enhance mechanical properties of PA/PBT blends. The mechanical property improvement is more pronounced in the PA‐rich blends than that in the PBT‐rich blends. The fracture behavior of the blend with less than 0.3 phr compatibilizer is governed by a particle pullout mechanism, whereas shear yielding is dominant in the fracture behavior of the blend with more than 0.3 phr compatibilizer. As the melt and crystallization temperatures of the base polymers are so close, either PA or PBT can be regarded as a mutual nucleating agent to enhance the crystallization on the other component. The presence of compatibilizer and in situ formed copolymer in the compatibilized blends tends to interfere with the crystallization of the base polymers in various blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 23–33, 2000     

Miscibility and crystallization behavior of PBT/epoxy blends

The miscibility and the isothermal crystallization kinetics for PBT/Epoxy blends have been studied by using differential scanning calorimetry, and several kinetic analyses have been used to describe the crystallization process. The Avrami exponents n were obtained for PBT/Epoxy blends. An addition of small amount of epoxy resin (3%) leads to an increase in the number of effective nuclei, thus resulting in an increase in crystallization rate and a stronger trend of instantaneous three‐dimensional growth. For isothermal crystallization, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of PBT component in the PBT/Epoxy blends. The Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT/Epoxy 97/3 had lower nucleation constant K_g than 100/0, 93/7, and 90/10 PBT/Epoxy blends. Analysis of the crystallization data of PBT/Epoxy blends showed that crystallization occurs in regime II. The fold surface free energy, σ_e = 101.7–58.0 × 10^?3 J/m², and work of chain folding, q = 5.79–3.30 kcal/mol, were determined. The equilibrium melting point depressions of PBT/Epoxy blends were observed and the Flory–Huggins interaction parameters were obtained. It indicated that these blends were thermodynamically miscible in the melt. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1320–1330, 2006     

Thermal studies on polypropylene/polyamide‐6 blends modified by succinic anhydride and succinyl fluorescein grafted polypropylenes

This study investigates the role played by two different interface agents on the basis of atactic polypropylene in the continuous/disperse phase polypropylene/polyamide‐6 (PP/PA6) system. The two agents used were obtained at the authors' laboratories from an atactic polypropylene byproduct derived from industrial polymerization reactors and consist of two grafted polymers containing either succinic anhydride (a‐PP‐SA) or both succinyl‐fluorescein and succinic anhydride grafted groups (a‐PP‐SF/SA). The role of these grafted polymers as compatibilizers in PP/PA6 polymer blends has been confirmed in previous investigations on the basis of their macroscopic behavior. This work investigates the thermal study of these blends where polypropylene acts as the polymer matrix and polyamide as the dispersed phase. Under isothermal conditions, thermal analysis agrees with the changes in the overall system behavior caused by the presence of the interface agents. These aspects were confirmed by polarized light microscopy that showed the morphology of the blends before and after modification with a‐PP‐SA or a‐PP‐SF/SA. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1307–1315, 2002     

马来酸酐接枝热塑性弹性体在PP/PA6共混物中的作用

研究了马来酸酐接枝热塑性弹性体 (TPEg )作为增容剂对聚丙烯 (PP) 尼龙 6 (PA6 )共混体系的相容性、相态以及物理力学性能的影响 .研究结果表明TPEg的加入大大改善了PP PA6共混体系的相容性 ,且随TPEg含量的增大分散相粒径明显降低 ,共混物的韧性以及延展性大大提高 ,同时拉伸强度及模量仍保持较好的水平 .TPEg增容的PP PA6共混物的非等温结晶行为的研究表明 ,共混物中PP和PA6的结晶行为不同于各自纯的聚合物 ,PA6作为成核剂使PP的结晶温度提高 ;而PA6由于TPEg的加入 ,出现分级结晶现象 ,一级结晶温度略低于纯PA6的结晶温度 ,且随TPEg含量增大结晶受阻 ,二级结晶温度与PP的接近 .由于PP、PA 6以及TPEg之间存在较强的相互作用 ,三元共混物中PP及PA6的玻璃化转变温度分别较其纯聚合物升高 .基于上述结果 ,提出了本共混体系的结构模型     

Structure,morphology, and crystallization process of isotactic polypropylene/hydrogenated hydrocarbon resin blends

The structure, morphology, and isothermal and nonisothermal crystallization of isotactic polypropylene/low‐molecular‐mass hydrocarbon resin blends (iPP/HR) (up to 20% in weight of HR) have been studied, using optical and electron microscopy, wide‐ and small‐angle X‐ray and differential scanning calorimetry. New structures and morphologies can be activated, using appropriate preparation and crystallization conditions and blend composition. For every composition and crystallization condition, iPP crystallizes in α‐form, with a spherulitic morphology. The size of iPP spherulites increases with resin content, whereas the long period decreases. In the range of crystallization temperatures investigated, HR modifies the birefringence of iPP spherulites, favoring the formation of radial lamellae and changing the ratio between tangential and radial lamellae. Spherulitic radial growth rates, overall crystallization rates, and melting temperatures are strongly affected by resin, monotonically decreasing with resin content. This confirms miscibility in the melt between the two components of the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3368–3379, 2004     

Solid-state relaxations in linear low-density (1-octene comonomer), low-density,and high-density polyethylene blends

Extensive thermal and relaxational behavior in the blends of linear low-density polyethylene (LLDPE) (1-octene comonomer) with low-density polyethylene (LDPE) and high-density polyethylene (HDPE) have been investigated to elucidate miscibility and molecular relaxations in the crystalline and amorphous phases by using a differential scanning calorimeter (DSC) and a dynamic mechanical thermal analyzer (DMTA). In the LLDPE/LDPE blends, two distinct endotherms during melting and crystallization by DSC were observed supporting the belief that LLDPE and LDPE exclude one another during crystallization. However, the dynamic mechanical β and γ relaxations of the blends indicate that the two constituents are miscible in the amorphous phase, while LLDPE dominates α relaxation. In the LLDPE/HDPE system, there was a single composition-dependent peak during melting and crystallization, and the heat of fusion varied linearly with composition supporting the incorporation of HDPE into the LLDPE crystals. The dynamic mechanical α, β, and γ relaxations of the blends display an intermediate behavior that indicates miscibility in both the crystalline and amorphous phases. In the LDPE/HDPE blend, the melting or crystallization peaks of LDPE were strongly influenced by HDPE. The behavior of the α relaxation was dominated by HDPE, while those of β and γ relaxations were intermediate of the constituents, which were similar to those of the LLDPE/HDPE blends. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1633–1642, 1997     

Influence of hyperbranched against linear architecture on crystallization behavior of poly(ε‐caprolactone)s in binary blends with poly(vinyl chloride)

Nonisothermal and isothermal crystallization behaviors of the hyperbranched poly(ε‐caprolactone) (HPCL)/poly(vinyl chloride) (PVC) and linear poly(ε‐caprolactone) (LPCL)/(PVC) blends were characterized with various blend composition such as 100/0, 95/5, 90/10, and 80/20, respectively. HPCL was synthesized through polycondensation of AB₂ macromonomer while LPCL and PVC were commercially purchased. The architectural characterization performed on ¹H NMR spectra revealed that HPCL consisted of about 3 AB₂ units and the linear segments consisted of 25 ε‐CL units. Through the nonisothermal crystallization analyses by modified Avrami approach with DSC crystallization exotherms, it was found that the crystallization rate was retarded by the increase in the noncrystallizable component (PVC) in the blends. This is in good agreement with the results of the isothermal crystallization analyses where time resolved small angle light scattering (SALS) and polarized optical microscopy (POM) were used. The effect of molecular architectural difference between HPCL and LPCL on the crystallization of their binary blends with PVC was elucidated by comparing the crystallization kinetic parameters. Both the nonisothermal and isothermal crystallization analyses showed that the crystallization rates of HPCL/PVC blends was faster than LPCL/PVC blends at given blend compositions. The faster crystallization of the HPCL/PVC blends is ascribed to the two specific architectural characteristics of HPCL; the branched structure and the incorporated long linear segments. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 577–589, 2007     

Miscibility and crystallization behavior in blends of poly(methyl methacrylate) and poly(vinylidene fluoride): Effect of star‐like topology of poly(methyl methacrylate) chain

A tetraarmed star‐shaped poly(methyl methacrylate) (s‐PMMA) was synthesized via atom transfer radical polymerization with 2‐bromoisobutyryl pentaerythritol as the initiator. For comparison, a linear PMMA with the identical molecular weight (l‐PMMA) was also prepared. The blends of the two PMMA samples with poly (vinylidene fluoride) (PVDF) were prepared to investigate the effect of macromolecular topological structure on miscibility and crystallization behavior of the binary blends. The behavior of single and composition‐dependent glass transition temperatures was found for the blends of s‐PMMA with PVDF, indicating that the s‐PMMA is miscible with PVDF in the amorphous state just like l‐PMMA. The miscibility was further evidenced by the depression of equilibrium melting points. It is found that the blends of s‐PMMA and PVDF displayed the larger k value of Gordon–Taylor equation than the blends of l‐PMMA and PVDF blends. According to the depression of equilibrium melting points, the intermolecular parameters for the two blends were estimated. It is noted that the s‐PMMA/PVDF blends displayed the lower interaction parameter than l‐PMMA/PVDF blends. The isothermal crystallization kinetics shows that the crystallization of PVDF in the blends containing s‐PMMA is faster than that in the blends containing the linear PMMA. The surface‐folding free energy of PVDF chains in the blends containing s‐PMMA is significantly lower than those in the blends containing l‐PMMA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2580–2593, 2007     

Preparation of fully cross‐linked CNBR/PP‐g‐GMA and CNBR/PP/PP‐g‐GMA thermoplastic elastomers and their morphology,structure and properties

Binary CNBR/PP‐g‐GMA and ternary CNBR/PP/PP‐g‐GMA thermoplastic elastomers were prepared by reactive blending carboxy nitrile rubber (CNBR) powder with nanometer dimension and polypropylene functionalized with glycidyl methacrylate (PP‐g‐GMA). Morphology observation by using an atomic force microscope (AFM) and TEM revealed that the size of CNBR dispersed phase in CNBR/PP‐g‐GMA binary blends was much smaller than that of the corresponding CNBR/PP binary blends. Thermal behavior of CNBR/PP‐g‐GMA and CNBR/PP blends was studied by DSC. Comparing with the plain PP‐g‐GMA, T_c of PP‐g‐GMA in CNBR/PP‐g‐GMA blends increased about 10 °C. Both thermodynamic and kinetic effects would influence the crystallization behavior of PP‐g‐GMA in CNBR/PP‐g‐GMA blends. At a fixed content of CNBR, the apparent viscosity of the blending system increased with increasing the content of PP‐g‐GMA. FTIR spectrum verified that the improvement of miscibility of CNBR and PP‐g‐GMA was originated from the reaction between carboxy end groups of CNBR and epoxy groups of GMA grafted onto PP molecular chains. Comparing with CNBR/PP blends, the tensile strength, stress at 100% strain, and elongation at break of CNBR/PP‐g‐GMA blends were greatly improved. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1042–1052, 2004     

聚酰胺6／聚醚砜共混体系的结晶与熔融行为

聚醚砜（ＰＥＳ）是一种非晶特种工程塑料，具有强度好，使用温度高等特点，但熔体粘度高，加工上有一定困难．聚酰胺６（ＰＡ６）是部分结晶的工程塑料，有很好的强度和耐磨性能．加入适量的ＰＡ６，可显著地降低ＰＥＳ的熔体粘度，且可基本保持ＰＥＳ的原有性能［１］．...     

Crystallization,melting behavior,and morphology of PP/Novolac blends

The crystallization, melting behavior, and morphology of Polypropylene (PP) and PP/Novolac blends were studied by scanning electron microscopy, wide angle X‐ray diffraction, differential scanning calorimetry, and polarized optical microscope. The results showed that the crystallization of PP in PP/Novolac blends was strongly influenced by crystallization temperature, particles size of Novolac, crosslinking, and compatibilizer maleic anhydride‐grafted PP. The Novolac resin could not only affect the crystal structure, but also acted as effective nucleating agents, accelerating the crystallization of PP in the PP/Novolac blends. And the smaller the Novolac particles were, the more effective were the nucleating agent for PP crystallization. Avrami equation was used to analyze the isothermal crystallization kinetics of PP and PP/Novolac blends. The influences of curing and compatibilizer on the crystallization behavior of PP were rather complicated. The crystallization thermodynamics were estimated using the Hoffman theory. The incorporation of cured Novolac and compatibilizer evidently decreased the chain folding energy of PP. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3288–3303, 2006     

Crystalline Morphology and Crystallization Characteristics of In-situ Blends of Anionic Polyamide 6 with Noncrystallizable Semiaromatic Polyamide Copolymer

A noncrystallizable semiaromatic polyamide copolymer(NSAP) was dissolved in molten caprolactam, and PA6/NSAP blends were produced in-situ via the anionic ring-opening polymerization of caprolactam. The presence of a single loss tangent(tanδ) peak measured by means of dynamic mechanical analysis(DMA) proves the miscibility between PA6 and NSAP in the blends. It was found that there existed drastic changes in the crystallographic form and crystallization kinetics for the in-situ blends, e.g., when 20% NSAP was added, nearly all crystallites existed in the γ form and the crystallization could hardly occur upon cooling even at a rate of 2.5 ℃/min. Moreover, cold crystallization appears during the subsequent heating, and its melting point is 40 ℃ lower than that of the virgin system. On the other hand, the size of the spherulites only decreases modestly. It is suggested that the introduction of irregular stiff segments originated from NSAP into PA6 macromolecule chain, which resulted from transamidation during the polymerization play a dominant role in the drastic change of crystallization kinetics and the resultant morphology of the in-situ blends.     

Study of clay nanocomposites of the biodegradable polyhexamethylene succinate. Application of isoconversional analysis to nonisothermal crystallization

Nanocomposites of organomodified montmorillonites and the biodegradable polyester derived from hexanediol and succinic acid were prepared by the solution‐casting method using chloroform as solvent. Samples were studied by means of X‐ray diffraction and transmission electron microscopy. Intercalated structures differentiated by the stacking mode between silicate layers were observed. The highest variability in interlayer spacing was found when C30B organoclay was added. In this case, hydroxyl groups of the modifier could interact with polar carbonyl groups of the polyester. Thermal stability and crystallization behavior under both isothermal and nonisothermal conditions were evaluated. The overall crystallization rate of the intercalated nanocomposites was higher than that of the neat polyester due to a significant increase in their nucleation density, which compensated for their lower crystal growth rate. Isoconversional analysis was used to determine effective activation energies and to estimate nucleation and transport energy parameters from nonisothermal hot crystallization experiments. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2234–2248, 2008     

Miscibility,melting, and crystallization of poly(butylene‐2,6‐naphthalate)/poly(ether imide) blends

We prepared blends of poly(butylene‐2,6‐naphthalate) (PBN) and poly(ether imide) (PEI) by solution‐casting from dichloroacetic acid solutions. The miscibility, crystallization, and melting behavior of the blends were investigated with differential scanning calorimetry (DSC) and dynamic mechanical analysis. PBN was miscible with PEI over the entire range of compositions, as shown by the existence of single composition‐dependent glass‐transition temperatures. In addition, a negative polymer–polymer interaction parameter was calculated, with the Nishi–Wang equation, based on the melting depression of PBN. In nonisothermal crystallization investigations, the depression of the crystallization temperature of PBN depended on the composition of the blend and the cooling rate; the presence of PEI reduced the number of PBN segments migrating to the crystallite/melt interface. Melting, recrystallization, and remelting processes occurring during the DSC heating scan caused the occurrence of multiple melting endotherms for PBN. We explored the effects of various experimental conditions on the melting behavior of PBN/PEI blends. The extent of recrystallization of the PBN component during DSC heating scans decreased as the PEI content, the heating rate, the crystallization temperature, and the crystallization time increased. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1694–1704, 2004     

Polymorphism of nylon-6 in nylon-6/nanoclay/functionalized polyolefin blends

The crystallization behavior of Nylon-6 and the interaction in Nylon-6/nanoclay/functionalized polyolefin blends were investigated by X-ray diffraction and Fourier transform infrared spectroscopy. For samples without any thermal history, the interaction between Nylon-6 and nanoclay or the interaction between Nylon-6 and functionalized polyolefin favors the formation of γ form crystal. In contrast, the presence of both nanoclay and functionalized polyolefin together in Nylon-6 was found to have an antagonistic effect on each other's ability to promote the formation of γ form crystal. This was attributed to the complex interactions between the constituents. The crystallization behavior of Nylon-6 in Nylon-6/nanoclay/functionalized polyolefin blends is clearly affected by the cointeraction of these effects. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1494–1502, 2007     

聚苯硫醚/尼龙6共混物界面对结晶行为的影响

高分子作为材料时 ,其力学性能受其结晶形态的影响 ,而其结晶形态与其结晶行为有关 .结晶性聚合物共混物中结晶组分由于第二组分存在 ,改变了结晶组分在熔体时的化学与物理环境 .因此 ,其结晶组分的结晶行为不仅取决于两组分在熔体时的相容性 ,而且与第二组分是否起到异相晶核作用和 /或两组分间界面是否诱导成核作用有关 ,从而影响共混物中结晶组分的结晶行为 ,导致共混物力学性能的改变[1～ 4] .在ＰＰＳ/ＰＡ6共混物中 ,由于ＰＰＳ的熔点和熔体结晶温度都比ＰＡ6的高 ,共混物熔体降温结晶ＰＰＳ是在ＰＡ6熔体存在下发生结晶 ,而ＰＡ6是在…     

Relationships between the molecular architecture,crystallization capacity,and miscibility in poly(butylene terephthalate)/polycarbonate blends: A comparison with poly(ethylene terephthalate)/polycarbonate blends

Poly(butylene terephthalate) (PBT)/polycarbonate (PC) samples, prepared via reactive blending in the presence of Ti‐ and Sm‐based catalysts, resulted in block copolymers whose block length decreased as the mixing time increased. A single homogeneous amorphous phase occurred when the blocks had monomeric sequences shorter than 10 units. Otherwise, a crystalline phase of PBT developed. Also, in poly(ethylene terephthalate) (PET)/PC blends previously studied, the miscibility was strictly correlated with the crystallizability of the system. Therefore, the miscibility of the PBT/PC and PET/PC blends was compared with respect to the tendency of the PBT and PET blocks to crystallize under isothermal conditions. The crystallization rate of the PBT/PC copolymers was faster than that of the PET/PC copolymers with similar block lengths. Accordingly, the minimum crystallizable sequence length of the PBT blocks was shorter than that of the PET blocks (18 vs 31 monomeric unit sequences). This behavior was interpreted as an effect of the more flexible PBT units, which had a greater tendency to fold and crystallize than the PET units. Therefore, PBT, the blocks of which tended to crystallize even if they were very short and phase‐separated, was characterized by a poorer compatibility with PC than that of PET. As a result, the block size had a fundamental role in determining the crystallizability and, therefore, phase behavior of the semicrystalline block copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2821–2832, 2004