Lamellar thickening in nascent poly(acrylonitrile) upon annealing

No systematic study has been reported on the lamellar thickening in atactic poly(acrylonitrile) (PAN) upon annealing because PAN, in the form of solution‐cast films or their drawn products, generally shows no small‐angle X‐ray scattering (SAXS) maximum corresponding to the lamellar thickness. In this work, PAN crystals were precipitated during the thermal polymerization of acrylonitrile in solution. The nascent PAN film, obtained by the filtration of the crystal suspension, exhibited a clear SAXS maximum revealing the lamellar structure. The lamellar thickening upon annealing of the nascent PAN films was studied in the temperature range 100–180 °C, where the degradation was minimal, as confirmed by the absence of an IR absorption band at 1605 cm⁻¹ ascribed to the cyclized nitrile groups. Above 190 °C, the degradation of the samples was significant, and the SAXS became too broad to determine the scattering maximum. The long period was significantly affected by the annealing time (t_a) and the temperature (T_a). Depending on t_a, three stages were observed for the lamellar thickening behavior. The lamellar thickness stayed constant in stage I (t_a = 0.5–3 min, depending on T_a), rapidly increased in stage II (t_a = 0.5–8 min), and stayed at a constant value characteristic for each T_a at yet longer t_a's in stage III. The lamellar thickness characteristic for T_a increased rapidly with increasing T_a at 165 °C (or higher), which was 152 °C lower than the estimated melting temperature of PAN (T_m = 317 °C). A possible mechanism for such lamellar thickening in PAN far below the T_m is discussed on the basis of the enhanced chain mobility in the crystalline phase above the crystal/crystal reversible transition at 165–170 °C detected by differential scanning calorimetry and wide‐angle X‐ray diffraction. The structural changes associated with annealing are also discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2571–2579, 2000     

Miscibility in crystalline/amorphous blends of poly(3-hydroxybutyrate)/DGEBA

A differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS) study of miscibility in blends of the semicrystalline polyester poly(3-hydroxybutyrate) (PHB) and amorphous monomer epoxy DGEBA (diglycidyl ether of bisphenol A) was performed. Evidence of the miscibility of PHB/DGEBA in the molten state was found from a DSC study of the dependence of glass transition temperature (T_g) as a function of the blend composition and isothermal crystallization, analyzing the melting point (T_m) as a function of blend composition. A negative value of Flory–Huggins interaction parameter χ_PD was obtained. Furthermore, the lamellar crystallinity in the blend was studied by SAXS as a function of the PHB content. Evidence of the segregation of the amorphous material out of the lamellar structure was obtained. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Lamellar‐level morphology induced by combined crystallization and liquid–liquid demixing in a poly(ethylene terephthalate)/poly(ethylene‐2,6‐naphthalate) blend

The lamellar‐level morphology of an extruded poly(ethylene terephthalate) (PET)/poly(ethylene‐2,6‐naphthalate) (PEN) blend was investigated with small‐angle X‐ray scattering (SAXS). Measurements were made as a function of the annealing time in the melt and the crystallization temperature. The characteristic morphological parameters at the lamellar level were determined by correlation function analysis of the SAXS data. At a low crystallization temperature of 120 °C, the increased amorphous layer thickness was identified in the blend, indicating that some PEN was incorporated into the interlamellar regions of PET during crystallization. The blend also showed a larger lamellar thickness than pure PET. A reason for the increase in the lamellar thickness might be that the formation of thinner lamellar stacks by secondary crystallization was significantly restricted because of the increased glass‐transition temperature. At high crystallization temperatures above 200 °C, the diffusion rates of noncrystallizable components were faster than the growth rates of crystals, with most of the noncrystallizable components escaping from the lamellar stacks. As a result, the blend showed an interfibrillar or interspherulitic morphology. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 317–324, 2002     

Crystalline structure of polyamide 12 as revealed by solid‐state 13C NMR and synchrotron WAXS and SAXS

The crystalline structure of polyamide‐12 (PA12) was studied by solid‐state ¹³C nuclear magnetic resonance (NMR) as well as by synchrotron wide‐ and small‐angle X‐ray scattering (WAXS and SAXS). Isotropic and oriented PA12 showed different NMR spectra ascribed to γ‐ and γ′‐crystalline modifications, respectively. On the basis of the position of the first diffraction peak, the isotropic γ‐form and the oriented γ′‐form were shown to be with hexagonal crystalline lattice at room temperature. When heated, the two PA12 polymorphs demonstrated different behaviors. Above 140 °C, the isotropic γ‐PA12 partially transformed into α‐modification. No such transition was observed with the oriented γ′‐PA12 phase even after annealing at temperatures close to melting. A γ′–γ transition was observed here only after isotropization by melting point. Various structural parameters were extracted from the WAXS and SAXS patterns and analyzed as a function of temperature and orientation: the degree of crystallinity, the d‐spacings, the Bragg's long spacings, the average thicknesses of the crystalline (l_c) and amorphous (l_a) phases, and the linear crystallinity x_cl within the lamellar stacks. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3720–3733, 2005     

A synchrotron SAXS study of miscible blends of semicrystalline poly(vinylidenefluoride) and semicrystalline poly(1,4‐butylene adipate). II. Crystallization,morphology, and PBA inclusion in PVF2 spherulites

The incorporation of poly(1,4‐butylene adipate) (PBA) and its crystallization behavior within poly(vinylidenefluoride) (PVF₂) spherulites in miscible PVF₂/PBA blends have been further studied with small‐angle X‐ray synchrotron scattering (SAXS). The incorporation of PBA into the PVF₂ interlamellar region was found to be dependent on the PVF₂ crystallization conditions. In our previous work, where the blends were crystallized by a one‐step quenching process directly from 190 (a single‐phase region) to 20 °C (a three‐phase region), the transition from PBA inclusion in the PVF₂ interlamellar region to interlamellar exclusion occurred at a PBA weight fraction of ∼ 0.5. In this case, where the blends were first quenched from 190 (a single‐phase region) to 130 °C (a two‐phase region) and then further quenched to 20 °C (a three‐phase region), the transition occurred at a PBA weight fraction of less than 0.3. That is, when a blend is crystallized under different conditions, different amounts of the PBA component are incorporated into the PVF₂ interlamellar phase. The thickness of the PVF₂ interlamellar phase, in turn, may affect the PBA crystalline structure in the interlamellar region. Time‐resolved SAXS was used to probe the crystallization dynamics of both PVF₂ and PBA components in a blend containing 60 wt % PBA. The blend was quenched from the single‐phase region at 190 to 130 °C to crystallize the PVF₂ component and was then further quenched to 20 °C to crystallize the PBA component. This study, together with our earlier results, shows that the time dependence of the PVF₂ crystallization rate and crystalline lamellar thickness is a function of the PBA content in the blend. The glass‐transition temperature of the blend and the PBA diffusion process are the two dominant factors that control the PVF₂ crystallization dynamics. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2296–2308, 2000     

Probing the early stages of thermal fractionation by successive self‐nucleation and annealing performed with fast scanning chip‐calorimetry

The thermal fractionation kinetics of a linear low‐density polyethylene (LLDPE) during Successive Self‐Nucleation and Annealing (SSA) is investigated by fast scanning chip‐calorimetry (FSC), by systematically varying the holding times (t_s) at each fractionation temperature (T_s). The range of explored fractionation times spans four orders of magnitude, from 0.001 to 10 s. Discernible thermal fractions are already detected in the very early stages of the process, at t_s shorter than one second. As t_s increases, the melting endotherm after SSA indicates a progressive lamellar thickening and narrowing of the thicknesses distribution of the various crystalline fractions. The largest variations are observed for the families of crystals containing the longest crystallizable sequences, which also undergo a change of their relative content as a consequence of self‐nucleated crystallization at T_s. The quality of the thermal fractionation obtained in 10 seconds with FSC is equivalent to that of conventional differential scanning calorimetry SSA (t_s = 300 s). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2200–2209     

Morphology development during isothermal crystallization. II. Isotactic and syndiotactic polypropylene blends

Morphology development during isothermal crystallization in equal molecular weight isotactic polypropylene (iPP), syndiotactic polypropylene (sPP), and iPP/sPP blends was studied with time‐resolved simultaneous small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) with synchrotron radiation. The sPP melting point is 15–20 °C below that of the iPP component, and sPP multiple melting is not affected by blending for 50–100 wt % sPP compositions. SAXS and WAXD (at 115 and 137.5 °C) show that sPP crystallizes more slowly than iPP. The sPP long spacing is larger than that of iPP at both crystallization temperatures, exhibits a broader distribution, and changes to a greater extent during crystallization. Differential scanning calorimetry (DSC) cooling and SAXS/WAXD measurements show iPP crystallizing first and nearly to completion before sPP in a 50:50 iPP/sPP blend. At 115 °C, iPP crystals nucleate sPP in a 50:50 blend and modify the sPP lamellar spacing. The nucleation does not overcome the large difference in the iPP and sPP rates at 137.5 °C. Before sPP crystallization in a 50:50 blend (115 °C), the iPP long spacing is not affected by molten sPP. The iPP long spacing is slightly expanded by molten sPP, and the WAXD induction time is delayed at 137.5 °C. The observed iPP long spacing in the presence of molten sPP is consistent with previously reported results for iPP/atactic polypropylene (aPP) blends of similar molecular weight. Quantitative differences between the two types of blends are consistent with previously reported thermodynamic rankings. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1876–1888, 2001     

On the origin of the multiple melting behavior in poly(ethylene naphthalene‐2,6‐dicarboxylate): Microstructural study as revealed by differential scanning calorimetry and X‐ray scattering

In this article a study on the melting behavior and microstructure of semicrystalline poly(ethylene naphthalene‐2,6‐dicarboxylate) (PEN) prepared by crystallization from the glass under different annealing conditions is presented. The influence of the annealing temperature (T_a), annealing time (t_a), and the heating rate (R_h) at which T_a is reached on the endothermic behavior of the samples was investigated by means of differential scanning calorimetry (DSC). A dual melting behavior appeared for low R_h values (2 deg · min⁻¹) within the range of 145 °C < T_a < 250 °C and 1 min ≤ t_a. ≤ 16 h. Samples subjected to fast heating rates (R_h = 200 deg · min⁻¹) to reach a T_a ≥ 230 °C showed DSC traces in which a transition is observed from three peaks to a single melting peak when t_a increases in the 30–240 min range. On the basis of the DSC results, PEN samples were prepared displaying single or dual endothermic behavior. The microstructure of these samples was studied by wide (WAXS) and small‐angle X‐Ray scattering (SAXS) techniques. The SAXS data were analyzed using the correlation function and interface distribution function formalisms, respectively. In samples with a single melting behavior, microstructural parameters such as the long spacing, the amorphous and the crystalline phase thicknesses are consistent with a lamellar stacking model in which the thickness distributions of both phases are almost the same. For samples exhibiting two melting endotherms, a dual lamellar model, which is in agreement with the experimental results is proposed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1167–1182, 2000     

Morphology development during isothermal crystallization. I. Isotactic and atactic polypropylene blends

Morphology development during isothermal crystallization in equal molecular weight isotactic polypropylene (iPP) and atactic polypropylene (aPP) blends was studied with time‐resolved simultaneous small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray scattering methods with synchrotron radiation. The final long period obtained after crystallization at 115 °C was nearly independent of blend composition up to 50 wt % aPP but showed an increase in the 80 wt % aPP blend. At a high crystallization temperature (137.5 °C), the increase in the final long period with aPP content was significant, and the evolution of iPP crystallinity was also affected. However, at low crystallization temperatures, the additive decrease of the crystallinity and the constant melting point with increasing aPP content suggest that the crystallizability and crystal morphology of iPP is not a strong function of aPP. The iPP/aPP blends showed a strong low‐angle SAXS upturn as a function of composition, which suggests the segregation of aPP on size scales larger than the lamellar spacing. A detailed analysis of the SAXS patterns indicates that aPP disrupts the ordering within the lamellar stacking. The results are generally consistent with predominantly interfibrillar incorporation of the aPP diluent within the microstructure, with only modest interlamellar incorporation dependent on the crystallization temperature. The findings can be attributed to the partial miscibility/mixing of the aPP and iPP components in the blend before crystallization, depending on the crystallization undercooling. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2580–2590, 2000     

Differential scanning calorimetry,small‐angle X‐ray scattering,and wide‐angle X‐ray scattering on homogeneous and heterogeneous ethylene‐α‐copolymers

The objective of this work was to use both X‐ray and differential scanning calorimetry techniques in a comparative study of the lamellar and crystalline structures of heterogeneous and homogeneous ethylene‐α‐copolymers. The samples differed in the comonomer type (1‐butene, 1‐hexene, 1‐octene, and hexadecene), comonomer content, and catalyst used in the polymerizations. Step crystallizations were performed with differential scanning calorimetry, and the crystallinity and lamellar thicknesses of the different crystal populations were determined. Wide‐angle X‐ray scattering was used to determine crystallinities, average sizes of the crystallites, and dimensions of the orthorhombic unit cell. The average thickness, separation of the lamellae, and volume fractions of the crystalline phase were determined by small‐angle X‐ray scattering (SAXS). The results revealed that at densities below 900 kg/m³, polymers were organized as poorly organized crystal bundles. The lamellar distances were smaller and the lamellar thickness distributions were narrower for the homogeneous ethylene copolymers than for the heterogeneous ones. Step‐crystallization experiments by SAXS demonstrated that the long period increased after annealing. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1860–1875, 2001     

Structure and morphology development in syndiotactic polypropylene during isothermal crystallization and subsequent melting

Structure and morphology development during the isothermal crystallization and subsequent melting of syndiotactic polypropylene (sPP) was studied with differential scanning calorimetry (DSC), time‐resolved simultaneous small‐angle X‐ray scattering (SAXS), and wide‐angle X‐ray diffraction (WAXD) methods with synchrotron radiation. The morphology of sPP isothermally crystallized at 100 °C for 3 h was also characterized with transmission electron microscopy (TEM). Time‐ and temperature‐dependent parameters such as the long period (L), crystal lamellar thickness (l_c), amorphous layer thickness (l_a), scattering invariant (Q), crystallinity (X_c), lateral crystal sizes (L₂₀₀ and L₀₁₀), and unit cell dimensions (a and b) were extracted from the SAXS and WAXD data. Results indicate that the decreases in L and l_c with time are probably due to the formation of thinner crystal lamellae, and the decreases in a and b are due to crystal perfection. The changes in the morphological parameters (Q, X_c, L, and l_c) during subsequent melting exhibited a two‐stage process that was consistent with the multiple melting peaks observed in DSC. The two high‐temperature peaks can be attributed to the melting of primary lamellae (at lower temperatures) and recrystallized lamellae (at higher temperatures). An additional minor peak, located at the lowest temperature, was also visible and was related to the melting of thin and defective secondary lamellae. TEM results are consistent with the SAXS data, which supports the assignment of the larger value (l₁) from the correlation function analysis as l_c. WAXD showed that the thermal expansion was greater along the b axis than the a axis during melting. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2982–2995, 2001     

Macromorphology of polypropylene homopolymer tacticity mixtures

The macromorphology of isotactic/atactic (iPP/aPP) and isotactic/syndiotactic (iPP/sPP) polypropylene mixtures is examined by optical microscopy. The spherulitic macrostructure of equimolecular weight [weight‐average molecular weight (M_w) = 200k] iPP/aPP blends is volume‐filling to very high aPP concentrations when the crystallization temperature is 130 °C. Similar spherulitic macrostructures (spherulite size and volume‐filling nature) are observed for iPP homopolymer and a 50/50 iPP/aPP blend at low crystallization temperatures (115–135 °C). At higher crystallization temperatures (140–145 °C), a equimolecular weight (M_w = 200k) 50/50 iPP/aPP blend exhibits nodular texture that blurs the spherulitic boundaries. Double temperature jump experiments show that the nodular texture is due to melt phase separation that develops prior to crystallization. The upper critical solution temperature (UCST) of a 50/50 iPP/aPP blend (M_w = 200k) lies below 155 °C, and the blend is miscible at conventional melt processing temperatures. The UCST behavior is controlled by the blend molecular weight and aPP microstructure. aPP microstructures containing increased isospecific sequencing (although still noncrystalline) exhibit a reduced tendency for phase separation in 50/50 mixtures (M_w = 200k) and the absence of nodular texture at low undercoolings (140–145 °C). Equimolecular weight (M_w = 200k) 50/50 iPP/sPP mixtures exhibit phase‐separated texture at all crystallization temperatures. The size scale of the phase‐separated texture decreases with decreasing crystallization temperature because of a competition between crystallization and phase separation from a melt initially well mixed from the initial solution blending process. Extended melt annealing experiments show that the 50/50 iPP/sPP mixture (M_w = 200k) is immiscible in the melt at conventional melt processing temperatures. The iPP/sPP pair shows a much stronger tendency for phase separation than the iPP/aPP polymer pair. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1947–1964, 2000     

Effect of the liquid–liquid phase separation on the crystallization behavior of a poly(ethylene‐ran‐vinyl acetate) and paraffin wax blend

The effect of liquid–liquid phase separation (LLPS) on the crystallization behavior of poly(ethylene‐ran‐vinyl acetate) with a vinyl acetate content of 9.5 wt % (EVA‐H) in the critical composition of a 35/65 (wt/wt) EVA‐H/paraffin wax blend was investigated by small‐angle light and X‐ray scattering methods and rheometry. This blend exhibited an upper critical solution temperature (UCST) of 98°C, and an LLPS was observed between the UCST and the melting point of 88°C for the EVA‐H in the blend. As the duration time in the LLPS region increased before crystallization at 65°C, both the spherulite size and the crystallization rate of the EVA‐H increased, but the degree of the lamellar ordering in the spherulite and the degree of crystallinity of the EVA‐H in the blend decreased. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 707–715, 2000     

Influence of polymer backbone branching on liquid crystal mesomorphous in nonequimolar complexes of poly(ethyleneimine) and dendritic amphiphiles

Two kinds of ionic self‐assembled complexes of linear or branched poly(ethyleneimine) (lPEI or bPEI) with Percec‐type dendrons [(3,4,5)16G1‐COOH] were prepared as lPEI‐(3,4,5)16G1‐x and bPEI‐(3,4,5)16G1‐x , where x is the mole ratio of the carboxyl groups of the dendritic amphiphile to the amino groups at the PEI chain. The crystal and mesomorphous structures and thermal properties of these complexes were investigated with X‐ray diffraction (XRD), Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), and polarized optical microscope (POM). Both the lPEI and bPEI complexes exhibited the same α_H crystal phase and similar lamellar mesomorphous phase, irrespective of the branching of the polymer backbone and the binding degree. The lPEI series complexes lPEI‐(3,4,5)16G1‐x , however, had more ordered lamellar stacking than that of the bPEI‐(3,4,5)16G1‐x complexes, so the thermotropic liquid crystal phase SmA was formed only in the lPEI‐(3,4,5)16G1‐x complexes beyond the melting point of the tail crystal of the dendritic amphiphile. No liquid crystalline phase was found from the bPEI‐(3,4,5)16G1‐x complexes. The results suggest that the branching of polymer backbone plays a key role to the formation of thermotropic liquid crystal in the polymer–dendritic amphiphile complex. The present finding is significant for the design of functional nanostructures based on the ionic complexation of polymers and amphiphiles. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Interfacial adhesion mechanisms in incompatible semicrystalline polymer systems

The mechanism of adhesion at semicrystalline polymer interfaces between isotactic polypropylene (iPP) and linear low‐density polyethylene (PE) was studied with transmission electron microscopy (TEM) and an asymmetric‐double‐cantilever‐beam test. From the TEM images, both the interfacial width and the lamellar thickness of the polymers were extracted. During annealing, the interfacial width increased with the annealing temperature, and this indicated the accumulation of amorphous polymers at the interface. The interfacial strength, determined from the critical fracture energy (G_c), also increased with the annealing temperature and reached a maximum above the melting temperatures of iPP and PE, whereas the smallest G_c value was obtained below the melting temperatures of the two materials. A mechanism of interfacial strengthening was proposed accounting for the competition between the interdiffusion of PE and crystallization of iPP. As the annealing temperature increased, the rates of PE diffusion and iPP crystallization increased. Although the crystallization of iPP hindered the interdiffusion of PE, both the interfacial width and the fracture energy increased with the temperature, and this indicated that PE interdiffusion dominated iPP crystallization. Below the critical temperature, the fracture surfaces of both iPP and PE were smooth, and chain pullout dominated the fracture mechanism. Above the critical temperature, iPP crystallization still hindered the interdiffusion, and crazes could be seen on the iPP side. Above the melting temperatures of the two materials, ruptured surfaces could also be seen on the PE side, and crazing was the fracture mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2667–2679, 2004     

Plasticization and cocrystallization in LLDPE/wax blends

The structure and thermal properties of linear low‐density polyethylene (LLDPE)/medium soft paraffin wax blends, prepared by melt mixing, were investigated by differential scanning calorimetry (DSC) and small‐ and wide‐angle X‐ray scattering (SAXS and WAXS). The blends form a single phase in the melt as determined by SAXS. Upon cooling from the melt, two crystalline phases develop for blends with more than 10 wt % wax characterized by widely different melting points. The wax acts as an effective plasticizer for LLDPE, decreasing both its crystallization and melting temperature. The higher melting point crystalline phase is formed by less branched LLDPE fractions. On the other hand, the lower melting point crystalline phase is a wax‐rich phase constituted by cocrystals of extended chain wax and short linear sequences of highly branched LLDPE chains. The presence of cocrystals was evidenced by standard DSC results, successive self‐nucleation and annealing (SSA) thermal fractionation and by the detection of a new SAXS signal attributed to the lamellar long period of the cocrystals. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1469–1482     

Solvent‐induced crystallization in poly(ethylene terephthalate) during mass transport

Solvent transport in poly(ethylene terephthalate) (PET) and related phase transformation were investigated. The data of mass sorption were analyzed according to Harmon's model for Case I (Fickian), Case II (swelling), and anomalous transport. This transport process in PET is accompanied by the induced crystallization of the original amorphous state. The transformation was examined by wide‐angle X‐ray scattering, small‐angle X‐ray scattering, differential scanning calorimetry, and Fourier transform infrared spectroscopy. During this process, the matrix is under a strain state that causes different kinetic paths of crystallization as compared with that by thermal annealing. This state of strain assists the development of the solvent‐induced crystallization. The model regarding crystallization was proposed in terms of the study of long period L, the crystal thickness l_c, and the thickness of amorphous layer l_a obtained from the one‐dimensional correlation function and interface distribution function. Different kinetic paths were discovered for different crystallization processes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1444–1453, 2002     

Effect of chain architecture on the phase transition of star and cyclic poly(N‐isopropylacrylamide) in water

The heat‐induced phase transition of aqueous solutions of Poly(N‐isopropylacrylamide) (PNIPAM) in water is examined for a four‐arm PNIPAM star (s‐PNIPAM), a cyclic PNIPAM (c‐PNIPAM), and their linear counterparts (l‐PNIPAM) in the case of polymers (1.0 g L^?1) of 12,700 g mol^?1 < M_n < 14,700 g mol^?1. Investigations by turbidity, high‐sensitivity differential scanning calorimetry (HS‐DSC), and light scattering (LS) indicate that the polymer architecture has a strong effect on the cloud point (T_c: decrease for s‐PNIPAM; increase for c‐PNIPAM), the phase transition enthalpy change (ΔH decrease for s‐PNIPAM and c‐PNIPAM), and the hydrodynamic radius of the aggregates formed above T_c (R_H: c‐PNIPAM < s‐PNIPAM < l‐PNIPAM). The properties of s‐PNIPAM are compared with those of previously reported PNIPAM star polymers (3 to 52 arms). The overall observations are described in terms of the arm molecular weight and the local chain density in the vicinity of the core of the star, by analogy with the model developed for PNIPAM brushes on nanoparticles or planar surfaces. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2059–2068.     

The study of electroactive block copolymer containing aniline pentamer isolated from different solvents

For the films and powder of polymers containing conductive oligomer are usually obtained from solution, the choice of better solvents for the regular arrangement of oligomers is very important for the higher conductivity. Because of the poor solubility of the oligomers, it is difficult to study the arrangement directly in most common solvents, so, we synthesized a triblock copolymer, mPEG2k‐aniline pentamer‐mPEG2k, as the model to investigate the arrangement–solvent relationship. For the poor solubility of the AP block in common solvents, the copolymer self‐assembled into spheric micelles in toluene and into lamellar crystals in water and THF. The crystallinity (X_c) and crystallization temperature (T_c) values of mPEG blocks in powders prepared from different solvents differed obviously, which may be the effect of different self‐assembled structures. From the two‐phase model of one‐dimensional electron density correlation function of SAXS, the long period of copolymer prepared from THF was presumably equal to the long period of pure mPEG plus the chain length of AP, which demonstrates that the AP blocks arrange regularly in the noncrystalline regions. In the selected solvents, the ones with higher polarity and better solubility induced more regular arrangement of AP blocks, which may be useful for choosing solvents for preparation of higher conductivity polymers' films containing aniline oligomers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1298–1307, 2009     

Hydrogen bonding interactions,crystallization, and surface hydrophobicity in nanostructured epoxy/block copolymer blends

Hydrogen bonding interactions, phase behavior, crystallization, and surface hydrophobicity in nanostructured blend of bisphenol A‐type epoxy resin (ER), for example, diglycidyl ether of bisphenol A (DGEBA) and poly(ε‐caprolactone)‐block‐poly(dimethyl siloxane)‐block‐poly(ε‐caprolactone) (PCL–PDMS–PCL) triblock copolymer were investigated by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, transmission electron microscopy, small‐angle X‐ray scattering, and contact angle measurements. The PCL–PDMS–PCL triblock copolymer consisted of two epoxy‐miscible PCL blocks and an epoxy‐immiscible PDMS block. The cured ER/PCL–PDMS–PCL blends showed composition‐dependent nanostructures from spherical and worm‐like microdomains to lamellar morphology. FTIR study revealed the existence of hydrogen bonding interactions between the PCL blocks and the cured epoxy, which was responsible for their miscibility. The overall crystallization rate of the PCL blocks in the blend decreased remarkably with increasing ER content, whereas the melting point was slightly depressed in the blends. The surface hydrophobicity of the cured ER increased upon addition of the block copolymer, whereas the surface free energy (γ_s) values decreased with increasing block copolymer concentration. The hydrophilicity of the epoxy could be reduced through blending with the PCL–PDMS–PCL block copolymer that contained a hydrophobic PDMS block. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 790–800, 2010