Investigation on Heat Transfer and Pressure Drop of Copper–Water Nanofluid Flow in Plain and Perforated Channels

This article reports an experimental study on copper–water nanofluid flow inside plain and perforated channels. The effects of flow rate and nanoparticle concentration on the heat transfer and pressure drop are studied. It is found that the perforated channel has a remarkable heat transfer enhancement of 24.6%. Furthermore, by using the copper–water nanofluid instead of the base fluid, the heat transfer coefficient as well as pressure drop are increased for both plain and perforated channels. A noticeable thermal performance factor of 1.34 is obtained for the simultaneous utilization of both the heat transfer enhancement techniques considered in this article.     

Intriguingly high convective heat transfer enhancement of nanofluid coolants in laminar flows

We reported on investigation of the convective heat transfer enhancement of nanofluids as coolants in laminar flows inside a circular copper tube with constant wall temperature. Nanofluids containing Al₂O₃, ZnO, TiO₂, and MgO nanoparticles were prepared with a mixture of 55 vol.% distilled water and 45 vol.% ethylene glycol as base fluid. It was found that the heat transfer behaviors of the nanofluids were highly depended on the volume fraction, average size, species of the suspended nanoparticles and the flow conditions. MgO, Al₂O₃, and ZnO nanofluids exhibited superior enhancements of heat transfer coefficient, with the highest enhancement up to 252% at a Reynolds number of 1000 for MgO nanofluid. Our results demonstrated that these oxide nanofluids might be promising alternatives for conventional coolants.     

Numerical investigation of laminar flow and heat transfer in a radial flow cooling system with the use of nanofluids

Nanofluids, because of their enhanced heat transfer capability as compared to normal water/glycol/oil based fluids, offer the engineer opportunities for development in areas where high heat transfer, low temperature tolerance and small component size are required. In this present paper, the hydrodynamic and thermal fields of a water–γAl₂O₃ nanofluid in a radial laminar flow cooling system are considered. Results indicate that considerable heat transfer enhancement is possible, even achieving a twofold increase in the case of a 10% nanoparticle volume fraction nanofluid. On the other hand, an increase in wall shear stress is also noticed with an increase in particle volume concentration.     

Numerical and Experimental Comparative Study on Nanofluids Flow and Heat Transfer in a Ribbed Triangular Duct

Numerical and experimental investigation is carried out to study the effect of combined vortex generator and nanofluids on turbulent heat transfer and fluid flow characteristics in an equilateral triangular duct. A triangular duct provides a lower heat transfer rate and lower pressure drop compared to other duct configurations. The improvement of heat transfer of these ducts increases their importance for providing higher heat transfer and lower pressure drop. Two different types of nanoparticles, namely Al₂O₃ and SiO₂, suspended in distilled water with two particle concentrations are successfully prepared and experimentally tested. The numerical and experimental results show dramatic heat transfer enhancement by using a vortex generator and nanofluids, simultaneously accomplished with a moderate increase in the friction factor. A low deviation has been seen between the present numerical and experimental results.     

Heat transfer enhancement by application of nano-powder

In this investigation, laminar flow heat transfer enhancement in circular tube utilizing different nanofluids including Al₂O₃ (20 nm), CuO (50 nm), and Cu (25 nm) nanoparticles in water was studied. Constant wall temperature was used as thermal boundary condition. The results indicate enhancement of heat transfer with increasing nanoparticle concentrations, but an optimum concentration for each nanofluid suspension can be found. Based on the experimental results, metallic nanoparticles show better enhancement of heat transfer coefficient in comparison with oxide particles. The promotions of heat transfer due to utilizing nanoparticles are higher than the theoretical correlation prediction.     

Experimental investigation of heat transfer and friction coefficient of the water/graphene oxide nanofluid in a pipe containing twisted tape inserts under air cross-flow

The water/graphene oxide nanofluid effect in a pipe equipped by twisted tape inserts under air cross-flow is investigated and the optimal tape geometry is determined. The range of internal and external Reynolds numbers are: 3800<Re_o<21500 and 550<Re_i<2000. Heat transfer and pressure drop increase by increasing Re and inserts width and heat transfer performance coefficient increased up to 1.4, indicating enhanced heat transfer compared to undesirable pressure drop. On the other hand, the heat transfer coefficient is 26% higher when compared with water in a plain tube. According to the results, this method is a good alternative in heat exchangers.     

Natural convective heat transfer of Ag-water nanofluid flow inside enclosure with center heater and bottom heat source

A numerical study on natural convective heat transfer inside an enclosure with center heater using nanofluid has been carried out. The effect of different length of center heater on the flow and temperature fields is analysed for different Rayleigh numbers. Results are displayed in terms of streamlines, isotherms, mid height velocity profile and average Nusselt number. The numerical results reveal heat transfer increases with increasing heater length at both vertical and horizontal positions for increasing values of Rayleigh numbers. In particular, a higher increase in heat transfer is obtained with heater situated with vertical position of maximum length. Also it is obtained that enhancement of heat transfer is high for Ag - water nanofluid than CuO -water and Al₂O₃ -water nanofluids.     

Saturated flow boiling characteristics in single rectangular minichannels: effect of aspect ratio

In this study, saturated flow boiling characteristics of deionized water in single rectangular minichannels are investigated experimentally. A special attention is paid to the effect of aspect ratio (channel width to depth, W_ch/H_ch) on the heat transfer and total pressure drop. Experiments are conducted for various values of the mass flux and the wall heat flux. Flow visualization is used as a complementary technique for a deeper physical understanding of flow phenomena. The results show that the channel aspect ratio has a significant effect on both the local two-phase heat transfer coefficient and the total pressure drop. In general manner, the aspect ratio of 1 presents the highest heat transfer coefficients, while the aspect ratio of 0.25 demonstrates the lowest ones. On the other hand, the lowest values of the pressure drop are obtained at the extreme values of the aspect ratio (0.25 and 4).     

Heat transfer behaviour of nanofluids in a uniformly heated circular tube fitted with helical inserts in laminar flow

The CFD simulation of heat transfer characteristics of a nanofluid in a circular tube fitted with helical twist inserts under constant heat flux has been explained using Fluent version 6.3.26 in laminar flow. Al₂O₃ nanoparticles in water of 0.5%, 1.0% and 1.5% concentrations and helical twist inserts of twist ratios 2.93, 3.91 and 4.89 has been used for the simulation. All thermophysical properties of nanofluids are temperature dependent. The heat transfer enhancement increases with Reynolds number and decreases with twist ratio with maximum for the twist ratio 2.93. By comparing the heat transfer rates of water and nanofluids, the increase in Nusselt number is 5%–31% for different helical inserts and different volume concentrations. The maximum heat transfer enhancement is 31.29% for helical insert of twist ratio 2.93 and for the volume concentration of 1.5% corresponding to the Reynolds number of 2039. The data obtained by simulation match with the literature value of water with the discrepancy of less than ±10% for plain tube and tube fitted with helical tape inserts for Nusselt number.     

Experimental thermal performance study of natural graphite as sensible heat storage material using different heat transfer fluids

In this paper thermal performance of graphite-based sensible heat storage system with embedded helical coil in rectangular shell was studied. Plain water at four flow rates (0.25 LPM–1.0 LPM) and four inlet temperatures (60°C–90°C) was passed through the graphite bed and charging time was measured. Expanded graphite/water suspension and Al₂O₃/water nanofluid were also used to study charging behavior of graphite. Results showed that charging time of packed bed was reduced with increase in flow rate and inlet temperature of heat transfer fluid. Charging time using expanded graphite/water solution and nanofluid was 14.2% and 21.2% lesser than water.

Abbreviations: h_i: internal heat transfer coefficient (W m^?2 K^?1); HTF: Heat transfer fluid; h_o: External heat transfer coefficient (W m^?2 K^?1); LPM: liter per minute; k: thermal conductivity (W m^?1 K^?1); TSU: Thermal storage unit     

Investigation of Laminar Convective Heat Transfer of a Novel Tio2–Carbon Nanotube Hybrid Water-Based Nanofluid

The current study was conducted to investigate the convective heat transfer coefficient of a novel TiO₂–CNT hybrid nanofluid through the shell-and-tube heat exchanger under a laminar flow and the effects of temperature and mass fraction on it. TiO₂–CNT hybrid nanofluids were prepared using a new and modified hydrolysis technique. The thermal conductivity of the TiO₂–CNT hybrid nanofluid and other thermo-physical properties were assessed. Results indicate that the effective thermal conductivity and heat transfer coefficient of the base fluid was influenced significantly and increased by the 0.2 wt% of this novel hybrid nanofluid in distilled water.     

Experimental evaluation of friction factor and heat transfer enhancement of twisted tape inserts using TiO<Subscript>2</Subscript>–water nanofluids

This paper studies the experimental evaluation of TiO₂ nanofluids in enhancing the heat transfer rate and friction factor on a micro-finned tube fitted with twisted tape inserts. Results show that the enhancement in heat transfer and pumping power completely depends on the concentration ratio of nanoparticles, pitch ratio and the type of pitch. Comparisons were made with the previous study with different operating parameters such as twist ratio and twist type. Viscosity of nanofluid increases with an increase in the concentration, which leads to increased pressure drop and pumping power. For the Reynolds number (Re = 4000), the maximum performance ratio was found as 2.1, 2, for concentration of 0.1 and 0.05, respectively. The addition of microfin arrangement inside the circular tube enhanced the performance ratio with minimum concentration of TiO₂ nanofluid.     

Heat Transfer and Hydrodynamic Performance Analysis of a Miniature Tangential Heat Sink Using Al2O3–H2O and TiO2–H2O Nanofluids

In this article, thermal and hydrodynamic performances of a miniature tangential heat sink are investigated experimentally by using Al₂O₃–H₂O and TiO₂–H₂O nanofluids. The effects of flow rate and volume concentration on the thermal performance have been investigated for the Reynolds number range of 210 to 1,100. Experimental results show that the average convective heat transfer coefficient increases 14 and 11% and the bottom temperature of the heat sink decreases 2.2°C and 1.6°C by using Al₂O₃–H₂O and TiO₂–H₂O nanofluid instead of pure distilled water, respectively.     

Numerical study of heat transfer enhancement of counter nanofluids flow in rectangular microchannel heat exchanger

This paper reports a numerical analysis of the performance of a counter-flow rectangular shaped microchannel heat exchanger (MCHE) using nanofluids as the working fluids. Finite volume method was used to solve the three-dimensional steady, laminar developing flow and conjugate heat transfer in aluminum MCHE. The nanofluids used were Ag, Al₂O₃, CuO, SiO₂, and TiO₂ and the performance was compared with water. The thermal, flow fields and performance of the MCHE were analyzed using different nanofluids, different Reynolds numbers and different nanoparticle concentrations. Temperature profile, heat transfer coefficient, pressure profile, and wall shear stress were obtained from the simulations and the performance was discussed in terms of heat transfer rate, pumping power, effectiveness, and performance index. Results indicated enhanced performance with the usage of nanofluids, and slight penalty in pressure drop. The increase in Reynolds number caused an increase in the heat transfer rate and a decrease in the overall bulk temperature of the cold fluid. The increase in nanoparticle concentration also yielded better performance at the expense of increased pressure drop.     

方腔内Cu/Al2O3水混合纳米流体自然对流的格子Boltzmann模拟

纳米流体作为一种较高的导热介质, 广泛应用于各个传热领域. 鉴于纳米颗粒导热系数和成本之间的矛盾, 本文提出了一种混合纳米流体. 为了研究混合纳米流体颗粒间相互作用机理和自然对流换热特性, 在考虑颗粒间相互作用力的基础上, 利用多尺度技术推导了纳米流体流场和温度场的格子Boltzmann方程, 通过耦合流动和温度场的演化方程, 建立了Cu/Al₂O₃水混合纳米流体的格子Boltzmann模型, 研究了混合纳米流体颗粒间的相互作用机理和纳米颗粒在腔体内的分布. 发现在颗粒间相互作用力中, 布朗力远远大于其他作用力, 温差驱动力和布朗力对纳米颗粒的分布影响最大. 分析了纳米颗粒组分、瑞利数对自然对流换热的影响, 对比了混合纳米流体(Cu/Al₂O₃-水)与单一金属颗粒纳米流体(Al₂O₃-水)的自然对流换热特性, 发现混合纳米流体具有更强的换热特性.     

Experimental Study of CuO/Water Nanofluid Turbulent Convective Heat Transfer in Square Cross-section Duct

Ducts with a square cross-section are widely used in many industrial applications because of their high compactness, easy forming, and low pressure drop. But the thermal performance of a duct will be reduced when the circular cross-sectional shape is not used. In this study, the convective heat transfer for a CuO/water nanofluid through a square cross-section duct in the turbulent flow regime has been investigated. The Nusselt number of nanofluids for different nanoparticle concentrations, as well as various Peclet numbers, was obtained. The results show considerable enhancement in the heat transfer coefficient and Nusselt number by increasing the nanoparticle concentrations as well as the Peclet number.     

Influence of metallic nanoparticles in water driven along a wavy circular cylinder

In the present study, simultaneous effects of metallic nanoparticles and magnetohydrodynamic due to stagnation point flow of nanofluid along a wave circular cylinder is presented. The effect of induced magnetic field is incorporated to deal the boundary and thermal boundary layer domain. Mathematical modelling for momentum and energy equation is constructed that is based upon three different kinds of nanoparticles namely: copper (Cu), Titanium di oxide (TiO₂), and alumina (Al₂O₃) within the working fluid water. Each mixture is analysed at the individual level and made comparison amongst all the mixture to examine the resistance and thermal conductivity of nanofluid within the boundary layer region. The solutions are exposed via boundary value problem using shooting method along with the Runge-Kutta-Fehlberg method. The characteristics of emerging parameters for the fluid flow and heat transfer are discussed through graphs and tables. The effects of ϕ (nanoparticle volume fraction) on heat transfer and shear stress at the wall are analysed in detail. It is finally concluded that by increasing the ratio of nanoparticles there is a significant increase in the temperature but slight decrease in the velocity profile.     

Hybrid nanofluid flow over two different geometries with Cattaneo–Christov heat flux model and heat generation: A model with correlation coefficient and probable error

The authors scrutinize the steady, MHD flow of SiO₂−MoS₂/water hybrid nanofluid towards two different geometries i.e. a wedge and a cone. The Tiwari and Das model is implemented with a generalized–Fourier's model, popularized as Cattaneo-Christov heat flux model. Analysis of heat transfer also incorporates the effects of suction, heat generation and thermal radiation. To showcase the relationship between engineering quantities and pertinent parameters involved in the study, the correlation coefficient for heat transfer coefficient and the skin friction coefficient is computed followed by the computation of probable error and statistical declaration. Similarity transformations are utilized to remodel the constitutive laws of flow in non-dimensional form. Numerical computation of non-linear, coupled O.D.E.’s is performed with the support of the Runge-Kutta-Fehlberg scheme and shooting method. Graphical and tabular illustrations of computed results are provided to report the variation in flow properties with the fluctuation in physical parameters. In both cases, i.e. flow close to a wedge and a cone, the temperature of hybrid nanofluid enhances on intensifying the thermal radiation and experiences a decrement with thermal relaxation parameter and magnetic field. Rising values of the suction parameter, thermal relaxation parameter, and thermal radiation cause increment in heat transfer coefficient. Interestingly, it was spotted that the heat generation parameter has contrary effects on temperature distribution over the two geometries.     

Heat Transfer and Pressure Drop Characteristics of Graphene Oxide/Water Nanofluid in a Circular Tube Fitted with Wire Coil Insert

In this work, heat transfer and pressure drop characteristics of graphene oxide/water nanofluid flow through a circular tube having a wire coil insert were studied. The required graphene oxide was synthesized via the Hummer method and characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (SRD), and scanning electron microscope (SEM) methods. Dispersing graphene oxide in the water, nanofluids with 0.02, 0.07, and 0.12% volume fraction were prepared. An experimental set-up was designed and made to investigate the heat transfer performance and pressure loss of nanofluids. All experiments were carried out in the constant heat flux at tube wall conditions. The volumetric flow rates of the nanofluid were adjusted at 6, 8, and 10 L/min. Thermal conductivity, specific heat, density, and viscosity as thermophysical properties of the nanofluid were calculated using graphene oxide and water properties at the average temperature via appropriate relations. These properties were applied to calculate the convective heat transfer coefficient, Nusselt number, and friction factors for each experiment. Finally, the constant and exponents of Duangthongsuk and Wongwises's correlations for Nusselt number and friction factor were corrected by experimental results. The achieved experimental data have shown good agreement with those predicted. The results have shown that 0.12 vol% of graphene oxide in the water can enhance convective heat transfer coefficient by about 77%. As a result, it can be concluded that the graphene oxide/water can be used in the heat transfer devices to achieve more efficiency.     

Prediction of thermal conductivity and viscosity of nanofluids by molecular dynamics simulation

Limitations of conventional heat transfer fluids in different industries because of their poor thermal conductivity made heat transfer improvement in working fluids was performing, as a new method of advanced heat transfer. Therefore, the dispersion solid particle idea in fluids, which has been started with mili- and micrometer particles, completed by using nanoparticles and today nanofluids have been found to provide a considerable heat transfer and viscosity enhancement in comparison to conventional fluids such as water, ethylene glycol, and engine oil. In this study, molecular dynamics simulation was used to predict thermal conductivity and viscosity of nanofluids. Water was used as a base fluid. The simple point charge-extended (SPC/E) model was used for simulation of water and Ewald sum method for electrostatic interactions. Lennard–Jones potential for Van der Waals interactions, KTS potential for water and SiO₂ and Spor and Heinzinger correlation for water and Pt were used. The results were compared with experimental data. For investigation of the effect of temperature, simulation was done for three temperatures of 20, 30, and 50?C. The results showed that the ratio of thermal conductivity of nanofluid to base fluid and viscosity will decrease as the temperature increases. The effect of the concentration of nanoparticle was studied for three different concentrations, namely, 0.45, 1.85, and 4%. The thermal conductivity of nanofluid increases with increasing the concentration. Moreover, the effect of two nanoparticle sizes (i.e., 5 and 7 nm) on the thermal conductivity of nanofluid was investigated. It was shown that an increase in the size causes a decrease in the thermal conductivity. Finally, by replacing the SiO₂nanoparticle with a Pt nanoparticle in the nanofluid, it was observed that the kind of nanoparticle had not a considerable effect on increasing the thermal conductivity of nanofluid.