MHD squeezed flow of water functionalized metallic nanoparticles over a sensor surface

Present study is devoted to analyze the magnetohydrodynamics (MHD) squeezed flow of nanofluid over a sensor surface. Modeling of the problem is based on the geometry and the interaction of three different kinds of metallic nanoparticles namely: copper (Cu), alumina (Al₂O₃) and titanium dioxide (TiO₂) with the homogeneous mixture of base fluid (water). The self-similar numerical solutions are presented for the reduced form of the system of coupled ordinary differential equations. The effects of nanoparticles volume friction, permeable velocity and squeezing parameter for the flow and heat transfer within the boundary layer are presented through graphs. Comparison among the solvent are constructed for both skin friction and Nusselt number. Flow behavior of the working nanofluid according to the present geometry has analyzed through Stream lines. Conclusion is drawn on the basis of entire investigation and it is found that in squeezing flow phenomena Cu–water gives the better heat transfer performance as compare with the rest of mixtures.     

The effects of different nano particles of Al2O3 and Ag on the MHD nano fluid flow and heat transfer in a microchannel including slip velocity and temperature jump

The forced convection of nanofluid flow in a long microchannel is studied numerically according to the finite volume approach and by using a developed computer code. Microchannel domain is under the influence of a magnetic field with uniform strength. The hot inlet nanofluid is cooled by the heat exchange with the cold microchannel walls. Different types of nanoparticles such as Al₂O₃ and Ag are examined while the base fluid is considered as water. Reynolds number are chosen as Re=10 and Re=100. Slip velocity and temperature jump boundary conditions are simulated along the microchannel walls at different values of slip coefficient for different amounts of Hartmann number. The investigation of magnetic field effect on slip velocity and temperature jump of nanofluid is presented for the first time. The results are shown as streamlines and isotherms; moreover the profiles of slip velocity and temperature jump are drawn. It is observed that more slip coefficient corresponds to less Nusselt number and more slip velocity especially at larger Hartmann number. It is recommended to use Al₂O₃-water nanofluid instead of Ag-water to increase the heat transfer rate from the microchannel walls at low values of Re. However at larger amounts of Re, the nanofluid composed of nanoparticles with higher thermal conductivity works better.     

Rapid communication: Transverse spin with coupled plasmons

The steady two-dimensional flow and heat transfer of a non-Newtonian power-law nanofluid over a stretching surface under convective boundary conditions and temperature-dependent fluid viscosity has been numerically investigated. The power-law rheology is adopted to describe non-Newtonian characteristics of the flow. Four different types of nanoparticles, namely copper (Cu), silver (Ag), alumina (Al ₂ O ₃) and titanium oxide (TiO ₂) are considered by using sodium alginate (SA) as the base non-Newtonian fluid. Lie symmetry group transformations are used to convert the boundary layer equations into non-linear ordinary differential equations. The transformed equations are solved numerically by using a shooting method with fourth-order Runge–Kutta integration scheme. The results show that the effect of viscosity on the heat transfer rate is remarkable only for relatively strong convective heating. Moreover, the skin friction coefficient and the rate of heat transfer increase with an increase in Biot number.     

Flow and heat transfer over a rotating porous disk in a nanofluid

The steady flow of an incompressible viscous fluid due to a rotating disk in a nanofluid is studied. The transformed boundary layer equations are solved numerically by a finite difference scheme, namely the Keller-box method. Numerical results for the flow and heat transfer characteristics are obtained for various values of the nanoparticle volume fraction parameter φ and suction/injection parameter h₀. Two models for the effective thermal conductivity of the nanofluid, namely the Maxwell-Garnett model and the Patel model, are considered. It is found that for the Patel model, the heat transfer rate at the surface increases for both suction and injection, whereas different behaviors are observed for the Maxwell-Garnett model, i.e. increasing the values of φ leads to a decrease in the heat transfer rate at the surface for suction, but increases for injection. The results of this study can be used in the design of an effective cooling system for electronic components to help ensure effective and safe operational conditions.     

Heat and mass transfer of MHD convective boundary layer flow past a stretching porous wall embedded in a porous medium

The hydromagnetic convective boundary layer flow past a stretching porous wall embedded in a porous medium with heat and mass transfer in the presence of a heat source and under the influence of a uniform magnetic field is studied. Exact solutions of the basic equations of motion, heat and mass transfer are obtained after reducing them to nonlinear ordinary differential equations. The reduced equations of heat and mass transfer are solved using a confluent hypergeometric function. The effects of the flow parameters such as a suction parameter (N), magnetic parameter (M), permeability parameter (K _p ), wall temperature parameter (r), wall concentration parameter (n), and heat source/sink parameter (Q) on the dynamics are discussed. It is observed that the suction parameter appears in the boundary condition ensuring the variable suction at the surface. Transverse component of the velocity increases only when magnetic field strength exceeds certain value, but the thermal boundary layer thickness and concentration distribution increase for all values. Results presented in this paper are in good agreement with the work of the previous author and also in conformity with the established theory.     

Heat transfer enhancement by application of nano-powder

In this investigation, laminar flow heat transfer enhancement in circular tube utilizing different nanofluids including Al₂O₃ (20 nm), CuO (50 nm), and Cu (25 nm) nanoparticles in water was studied. Constant wall temperature was used as thermal boundary condition. The results indicate enhancement of heat transfer with increasing nanoparticle concentrations, but an optimum concentration for each nanofluid suspension can be found. Based on the experimental results, metallic nanoparticles show better enhancement of heat transfer coefficient in comparison with oxide particles. The promotions of heat transfer due to utilizing nanoparticles are higher than the theoretical correlation prediction.     

Non-Darcy free convection of Fe3O4-water nanoliquid in a complex shaped enclosure under impact of uniform Lorentz force

Effect of Lorentz forces on natural convection in a complex shaped cavity filled with nanoliquid immersed in porous medium is investigated by means of Control volume based finite element method (CVFEM). Non Darcy model is taken into account for porous media. The working fluid is Fe₃O₄ –water and its viscosity considered as function of magnetic field. Figures are illustrated for different values of Darcy number (Da), Fe₃O₄ -water volume fraction (?), Rayleigh (Ra) and Hartmann (Ha) numbers. Results depict that enhancing in Lorentz forces results in reduce in nanofluid motion and increase the thickness of thermal boundary. Convective heat transfer enhances with rise of Darcy number.     

方腔内Cu/Al2O3水混合纳米流体自然对流的格子Boltzmann模拟

纳米流体作为一种较高的导热介质, 广泛应用于各个传热领域. 鉴于纳米颗粒导热系数和成本之间的矛盾, 本文提出了一种混合纳米流体. 为了研究混合纳米流体颗粒间相互作用机理和自然对流换热特性, 在考虑颗粒间相互作用力的基础上, 利用多尺度技术推导了纳米流体流场和温度场的格子Boltzmann方程, 通过耦合流动和温度场的演化方程, 建立了Cu/Al₂O₃水混合纳米流体的格子Boltzmann模型, 研究了混合纳米流体颗粒间的相互作用机理和纳米颗粒在腔体内的分布. 发现在颗粒间相互作用力中, 布朗力远远大于其他作用力, 温差驱动力和布朗力对纳米颗粒的分布影响最大. 分析了纳米颗粒组分、瑞利数对自然对流换热的影响, 对比了混合纳米流体(Cu/Al₂O₃-水)与单一金属颗粒纳米流体(Al₂O₃-水)的自然对流换热特性, 发现混合纳米流体具有更强的换热特性.     

Magnetized nanofluid flow of ferromagnetic nanoparticles from parallel stretchable rotating disk with variable viscosity and thermal conductivity

The current work aims at studying a constructed mathematical model with an examination of heat transfer in water-based nanofluids containing ferromagnetic nanoparticles flowing between parallel stretchable spinning discs with variable viscosity influence and variable conductivity. The nonlinear coupling of the ordinary differential equations of the momentum and energy equation with the partial differential equations based on the Navier-Stokes equation employing some influential similarity transformations. The transformed system of ordinary differential equations has been solved through the Chebyshev spectral collocation procedure (CSCP). The numerical results for the velocity and temperature distributions are shown in terms of graphical presentations. The existing available literature was utilized to test for validation of the numerical findings. The outcomes demonstrate that the stretching of the lower and upper disks and spinning parameters strengthens the impetus boundary layer and diminished the temperature boundary layer, whilst the variable thermal conductivity improved the convective and conductive strength of the ferromagnetic nanoparticles considered, and the Fe₃O₄ nanofluid displays a higher thermal conductivity strength than the Mn-ZnFe₂O₄ nanofluid.     

Effect of Brownian motion on flow and heat transfer of nanofluids over a backward-facing step with and without adiabatic square cylinder

A mathematical model to predict large enhancement of thermal conductivity of nanofluids by considering the Brownian motion is proposed. The effect of the Brownian motion on the flow and heat transfer characteristics is examined. The computations were done for various types of nanoparticles such as CuO, Al₂O₃, and ZnO dispersed in a base fluid (water), volume fraction of nanoparticles ? in the range of 1 % to 6 % at a fixed Reynolds number Re = 450 and nanoparticle diameter d_np = 30 nm. Our results demonstrate that Brownian motion could be an important factor that enhances the thermal conductivity of nanofluids. Nanofluid of Al₂O₃ is observed to have the highest Nusselt number Nu among other nanofluids types, while nanofluid of ZnO nanoparticles has the lowest Nu. Effects of the square cylinder on heat transfer characteristics are significant with considering Brownian motion. Enhancement in the maximum value of Nu of 29 % and 26 % are obtained at the lower and the upper walls of the channel, respectively, by considering the Brownian effects, with square cylinder, compared with that in the case without considering the Brownian motion. On the other hand, results show a marked improvement in heat transfer compared to the base fluid, this improvement is more pronounced on the upper wall for higher ?.     

Intriguingly high convective heat transfer enhancement of nanofluid coolants in laminar flows

We reported on investigation of the convective heat transfer enhancement of nanofluids as coolants in laminar flows inside a circular copper tube with constant wall temperature. Nanofluids containing Al₂O₃, ZnO, TiO₂, and MgO nanoparticles were prepared with a mixture of 55 vol.% distilled water and 45 vol.% ethylene glycol as base fluid. It was found that the heat transfer behaviors of the nanofluids were highly depended on the volume fraction, average size, species of the suspended nanoparticles and the flow conditions. MgO, Al₂O₃, and ZnO nanofluids exhibited superior enhancements of heat transfer coefficient, with the highest enhancement up to 252% at a Reynolds number of 1000 for MgO nanofluid. Our results demonstrated that these oxide nanofluids might be promising alternatives for conventional coolants.     

Investigation of Laminar Convective Heat Transfer of a Novel Tio2–Carbon Nanotube Hybrid Water-Based Nanofluid

The current study was conducted to investigate the convective heat transfer coefficient of a novel TiO₂–CNT hybrid nanofluid through the shell-and-tube heat exchanger under a laminar flow and the effects of temperature and mass fraction on it. TiO₂–CNT hybrid nanofluids were prepared using a new and modified hydrolysis technique. The thermal conductivity of the TiO₂–CNT hybrid nanofluid and other thermo-physical properties were assessed. Results indicate that the effective thermal conductivity and heat transfer coefficient of the base fluid was influenced significantly and increased by the 0.2 wt% of this novel hybrid nanofluid in distilled water.     

Thermo-physical characteristics during the flow and heat transfer analysis of GO-nanoparticles adjacent to a continuously moving thin needle

Nanofluids have shown significant promise in thermal enhancement of many industrial systems and they have been used extensively in energy applications during recent years. Keeping such applications in mind, the present work exhibits a two-dimensional numerical simulation for the boundary layer flow of Graphene oxide (GO)-nanofluids adjacent to a thin needle along with heat transfer. Influence of heat generation/absorption and viscous dissipation have been included to explore the heat transport analysis. The nanofluid flow is generated due to a continuously moving horizontal thin needle. The non-linear expressions governing the flow and heat transfer analysis are changed into dimensionless form by introducing new dimensionless variables. The novelty of current study is to predict the multiple numerical solutions for dimensionless velocity and temperature fields. Numerical computations and graphical delineations were done with the assistance of MATLAB software. This study explores the impacts of several dimensionless key parameters, like, magnetic parameter, Prandtl number, nanoparticles volume fraction and ratio of needle's velocities on the flow and thermal distributions. The computational results have proved that the fluid temperature enhances for higher values of nanoparticles volume fraction while an opposite is true for velocity distributions. In addition, the computed outcomes revealed that for the case of upper branch solution, significant reduction in skin-friction coefficient is seen for higher magnetic parameter.     

Hall effect on MHD flow and heat transfer of nanofluids over a stretching wedge in the presence of velocity slip and Joule heating

This paper deals with the boundary layer flow and heat transfer of nanofluids over a stretching wedge with velocity-slip boundary conditions. In this analysis, Hall effect and Joule heating are taken into consideration. Four different types of water-base nanofluids containing copper (Cu), silver (Ag), alumina (Al₂O₃), and titania (TiO₂) nanoparticles are analyzed. The partial differential equations governing the flow and temperature fields are converted into a system of nonlinear ordinary differential equations using a similarity transformation. The resulting similarity equations are then solved by using the shooting technique along with the fourth order Runge-Kutta method. The effects of types of nanoparticles, the volume fraction of nanoparticles, the magnetic parameter, the Hall parameter, the wedge angle parameter, and the velocityslip parameter on the velocity and temperature fields are discussed and presented graphically, respectively.     

Lattice Boltzmann method for nanofluid flow in a porous cavity with heat sources and magnetic field

In this article, Lattice Boltzmann method (LBM) has been applied to investigate the influences of magnetic field and heat sources on water based nanofluid natural convection inside a porous cavity with three square heat sources. Koo–Kleinstreuer–Li (KKL) model is applied to study Brownian motion impact on nanofluid flow. Effects of Rayleigh number (Ra), Darcy number (Da), nanofluid volume fraction (ϕ), and Hartmann number (Ha) on heat transfer characteristics are analyzed. From the obtained results we observe a decrease in the temperature gradient with increasing Ha; while quite the opposite effect is true with increasing Da and Ra. In the absence of magnetic field, for higher values of Darcy and Rayleigh numbers, thermal plumes are generated and the temperature gradient is enhanced. Moreover, small eddies are generated near the vertical centerline. However, in the presence of magnetic field, the number of thermal plumes decreases.     

Magnetohydrodynamics (MHD) axisymmetric flow and heat transfer of a hybrid nanofluid past a radially permeable stretching/shrinking sheet with Joule heating

The main interest of the present work is to fundamentally investigate the flow characteristics and heat transfer of a hybrid Cu-Al₂O₃/water nanofluid due to a radially stretching/shrinking surface with the mutual effects of MHD, suction and Joule heating. The surface is permeable to physically allow the wall mass fluid suction. Tiwari and Das model of nanofluid is used with the new thermophysical properties of hybrid nanofluid to represent the problem. A similarity transformation is adopted to convert the governing model (PDEs) into a nonlinear set of ordinary differential equations (ODEs). A bvp4c solver in MATLAB software is employed to numerically compute the transformed system. The numerical results are discussed and graphically manifested in velocity and temperature profiles, as well as the skin friction coefficient and heat transfer rate with the pertinent values of the dimensionless parameters namely magnetic, Cu volume fraction, suction and Eckert number. The Eckert number has no impact on the boundary layer separation while the higher value of the suction parameter may affect the heat transfer performance. The presence of dual solutions (first and second) is seen on all the profiles within a limited range of the physical parameters. The stability analysis is executed, and it is validated that the first solution is the real solution.     

Unsteady boundary layer flow of a nanofluid over a stretching sheet with variable fluid properties in the presence of thermal radiation

In this paper, we investigated numerically an unsteady boundary layer flow of a nanofluid over a stretching sheet in the presence of thermal radiation with variable fluid properties. Using a set of suitable similarity transformations, the governing partial differential equations are reduced into a set of nonlinear ordinary differential equations. System of the nonlinear ordinary differential equations are then solved by the Keller-box method. The physical parameters taken into consideration for the present study are: Prandtl number Pr, Lewis number Le, Brownian motion parameter N _b, thermophoresis parameter N _t, radiation parameter N _r, unsteady parameter M. In addition to these parameters, two more new parameters namely variable thermophoretic diffusion coefficient parameter e and variable Brownian motion diffusion coefficient parameter β have been introduced in the present study. Effects of these parameters on temperature, volume fraction of the nanoparticles, surface heat and mass transfer rates are presented graphically and discussed briefly. To validate our method, we have compared the present results with some previously reported results in the literature. The results are found to be in a very good agreement.     

Axisymmetric Stagnation-Point Flow of Nanofluid over a Stretching Surface

This paper investigates the laminar boundary layer flow of nanofluid induced by a radially stretching sheet. Nanofluid model exhibiting Brownian motion and thermophoresis is used. Series solutions for a reduced system of nonlinear ordinary differential equations are obtained by homotopy analysis method (HAM). Comparative study between the HAM solutions and previously published numerical results shows an excellent agreement. Velocity, temperature and mass fraction are displayed for various values of parameters. The local skin friction coefficient, the local Nusselt number and the local Sherwood number are computed. It is observed that the presence of nanoparticles enhances the thermal conductivity of base fluid. It is found that the convective heat transfer coefficient (Nusselt number) is decreased with an increase in concentration of nanoparticles whereas Sherwood number increases when concentration of nanoparticles in the base fluid is increased.     

Unsteady radiative nanofluid flow near a vertical heated wavy surface with temperature-dependent viscosity

In the present contribution, a numerical treatment is provided to describe unsteady nanofluid flow near a vertical heated wavy surface. A memorable feature of the present work is the investigation of nanofluid flow associated with thermal radiation that acts as a catalyst for heat transfer rates. Likewise, the effectiveness of variable viscosity is examined as it controls fluid flow as well as heat transfer. It is necessary to study heat and mass transfer for complex geometries because predicting heat and mass transfer for irregular surfaces is a topic of fundamental importance, and irregular surfaces frequently appear in many applications, such as flat-plate solar collectors and flat-plate condensers in refrigerators. A simple coordinate transformation from the wavy surface into a flat one is employed. The non-dimensional boundary layer equations that governing both heat transfer and nanofluid flow phenomena along the wavy surface are solved via a powerful numerical approach called the implicit Chebyshev pseudospectral (ICPS) method with Mathematica code. A comparison graph of the current numerical computation and the published data shows a perfect match. Figures depict the effect of various physical parameters on nanofluid velocities, temperature, salt concentration, nanoparticle concentration, skin friction, Sherwood, nanoparticle Sherwood, and Nusselt numbers. According to the numerical results, increasing the variable viscosity parameter value causes a drop in the local skin friction coefficient value and an increase in the steady-state axial nanofluid velocity profile near the wavy surface. Furthermore, as heat radiation is increased, the local Nusselt number decreases but the nanoparticle Sherwood number increases.     

Convective Heat Transfer of a Cu/Water Nanofluid Flowing Through a Circular Tube

Abstract

Fluids in which nanometer-sized solid particles are suspended are called nanofluids. These fluids can be employed to increase the heat transfer rate in various applications. In this study, the convective heat transfer for Cu/water nanofluid through a circular tube was experimentally investigated. The flow was laminar, and constant wall temperature was used as thermal boundary condition. The Nusselt number of nanofluids for different nanoparticle concentrations, as well as various Peclet numbers, was obtained. Also, the rheological properties of the nanofluid for different volume fractions of nanoparticles were measured and compared with theoretical models. The results show that the heat transfer coefficient is enhanced by increasing the nanoparticle concentrations as well as the Peclet number.