Role of thiol‐disulfide exchange in episulfide polymerization

Episulfide polymerization offers a number of features that are uncommon in other ring‐opening anionic mechanisms. Besides the negligible sensitivity to water, the most distinctive and novel one is likely to be the role of disulfides, which may act both at the levels of chain transfer and end‐capping, producing polymers that feature both terminal and internal disulfides. In this article, we have qualitatively studied the kinetics of chain transfer and measured the thiolate–disulfide exchange equilibrium constants. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2233–2249, 2008     

The effect of feed conditions in the emulsion catalytic chain transfer polymerization of alkyl methacrylates

([bis[μ-[(2,3-butanedione dioximato)(2-)-O:O′]] tetrafluorodiborato(2-)-N,N′,N″,N‴] cobalt), CoBF, has been used for the effective catalytic chain transfer of alkyl methacrylate homo- and copolymers under emulsion polymerization conditions. The catalytic chain transfer process reduces the rate of polymerization such that when the monomer is fed over 60 min the instantaneous conversion is low enough for the particle to be swollen with monomer, allowing diffusion of the catalysts between the aqueous and monomer phases. When the amount of the catalyst is reduced, the rate is increased, eventually leading to viscous, glassy particles that prevent catalyst mobility, which is observed as a breakdown in the polymerization mechanism. This can be circumvented by the addition of a 20% shot of monomer at the start of the reaction. The effective chain transfer coefficient decreases on increasing the length of the ester group of the methacrylate. The analysis of the polymers made by the technique described shows that the T_g of the polymers observe a broad transition due to the effect of chain length being pronounced at low molecular mass. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3549–3557, 1999     

Synthesis of well‐defined polymeric activated esters

Monomers bearing an activated ester group can be polymerized under various controlled polymerization techniques, such as ATRP, NMP, RAFT polymerization, or ROMP. Combining the functionalization of polymers via polymeric activated esters with these controlled polymerization techniques generate possibilities to realize highly functionalized polymer architectures. Within this highlight two different research areas of activated esters in polymer science will be discussed: (i) the preparation of defined reactive polymer architectures by controlled polymerization techniques and (ii) the preparation of defined reactive thin films. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6677–6687, 2008     

A new photoiniferter/RAFT agent for ambient temperature rapid and well‐controlled radical polymerization

Phenacyl morpholine‐4‐dithiocarbamate is synthesized and characterized. Its capability to act as both a photoiniferter and reversible addition fragmentation chain transfer agent for the polymerization of styrene is examined. Polymerization carried out in bulk under ultra violet irradiation at above 300 nm at room temperature shows controlled free radical polymerization characteristics up to 50% conversions and produces well‐defined polymers with molecular weights close to those predicted from theory and relatively narrow poyldispersities (M_w/M_n ～ 1.30). End group determination and block copolymerization with methyl acrylate suggest that morpholino dithiocarbamate groups were attained at the end of the polymer. Photolysis and polymerization studies revealed that polymerization proceeds via both reversible termination and RAFT mechanisms. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3387–3395, 2008     

Synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers by combining ATRP and RAFT polymerizations

The synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers using a combination of two living radical polymerization techniques, atom transfer radical polymerization (ATRP) and reversible addition‐fragmentation chain transfer (RAFT) polymerization, is reported. The use of two methods is due to the disparity in reactivity of the two monomers, viz. vinyl acetate is difficult to polymerize via ATRP, and a suitable RAFT agent that can control the polymerization of vinyl acetate is typically unable to control the polymerization of tert‐butyl acrylate. Thus, ATRP was performed to make poly(tert‐butyl acrylate) containing a bromine end group. This end group was subsequently substituted with a xanthate moiety. Various spectroscopic methods were used to confirm the substitution. The poly(tert‐butyl acrylate) macro‐RAFT agent was then used to produce (tert‐butyl acrylate‐block‐vinyl acetate). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7200–7206, 2008     

One‐pot synthesis of linear‐hyperbranched diblock copolymers via self‐condensing vinyl polymerization and ring opening polymerization

The linear poly(ε–caprolacton)‐b‐hyperbrached poly(2‐((α‐bromobutyryl)oxy)ethyl acrylate) (LPCL‐b‐HPBBEA) has been successfully synthesized by simultaneous ring‐opening polymerization (ROP) of CL and self‐condensing vinyl polymerization (SCVP) of BBEA in one‐pot. The HPBBEA homopolymers were found to be formed in the polymerization because of the competitive reactions induced by initiation with bifunctional initiator, 2‐hydroxylethyl‐2′‐bromoisobutyrate (HEBiB), and inimer BBEA. The separation of LPCL‐b‐HPBBEA from the polymerization products was achieved by precipitation in methanol. With feed ratio increase of CL and BBEA to HEBiB, the molecular weights of PCL and HPBBEA blocks in the block copolymer enhanced; and the polymerization rate of CL started to decrease gradually after 12 h of polymerization, but the polymerization rate of BBEA was maintained until 24 h of polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7628–7636, 2008     

Thermosensitive gradient copolymers by living cationic polymerization: Semibatch precision synthesis and stepwise dehydration‐induced micellization and physical gelation

Thermosensitive forced gradient copolymers with various sequence distributions were synthesized by living cationic polymerization in the presence of an added base. The synthesis was conducted using a semibatch reaction method, which is unfavorable for ionic polymerization, especially when a simple apparatus is employed. Polymerization of 2‐ethoxyethyl vinyl ether (EOVE) was initiated using a conventional syringe technique. Immediately after initiation, 2‐methoxyethyl vinyl ether (MOVE) was continuously added using a syringe pump at regulated feed rates, which allowed control of the sequence distribution. The resulting gradient copolymers of EOVE and MOVE underwent thermally induced association in water, forming micelles with a hydrophobic core derived from EOVE‐rich segments. Interestingly, the size of the micelles obtained from gradient copolymers decreased monotonously with increasing solution temperature, while the micelles of the corresponding block copolymers were unchanged in size. This self‐association behavior can be controlled by designing the gradient pattern of the instantaneous composition. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6151–6164, 2008     

End group transformations of RAFT‐generated polymers with bismaleimides: Functional telechelics and modular block copolymers

End group activation of polymers prepared by reversible addition‐fragmentation chain transfer (RAFT) polymerization was accomplished by conversion of thiocarbonylthio end groups to thiols and subsequent reaction with excess of a bismaleimide. Poly(N‐isopropylacrylamide) (PNIPAM) was prepared by RAFT, and subsequent aminolysis led to sulfhydryl‐terminated polymers that reacted with an excess of 1,8‐bismaleimidodiethyleneglycol to yield maleimido‐terminated macromolecules. The maleimido end groups allowed near‐quantitative coupling with model low molecular weight thiols or dienes by Michael addition or Diels‐Alder reactions, respectively. Reaction of maleimide‐activated PNIPAM with another thiol‐terminated polymer proved an efficient means of preparing block copolymers by a modular coupling approach. Successful end group functionalization of the well‐defined polymers was confirmed by combination of UV–vis, FTIR, and NMR spectroscopy and gel permeation chromatography. The general strategy proved to be versatile for the preparation of functional telechelics and modular block copolymers from RAFT‐generated (co)polymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5093–5100, 2008     

The effect of a trithiol and inorganic fillers on the photo‐induced thermal frontal polymerization of a triacrylate

Thermal frontal polymerization is a process in which a localized reaction propagates through an unstirred system by the coupling of the thermal diffusion and the Arrhenius kinetics of an exothermic polymerization. A trithiol was found to affect the front velocity and the time for inducing a front upon exposure to UV light for trimethylolpropane triacrylate polymerization fronts with either kaolin or calcium carbonate filler present. The addition of trithiol and filler both decreased the front velocity. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8091–8096, 2008     

Preparation of a xanthate‐terminated dextran by click chemistry: Application to the synthesis of polysaccharide‐coated nanoparticles via surfactant‐free ab initio emulsion polymerization of vinyl acetate

Stable monodisperse poly(vinyl acetate) (PVAc) submicronic latex particles were synthesized by ab initio batch emulsion polymerization using a dextran derivative from renewable resource as an efficient steric stabilizer. The dextranend‐functionalized by a xanthate moiety was synthesized by Huisgen's 1,3‐dipolar cycloaddition (click chemistry). It was applied as a macromolecular RAFT (reversible addition fragmentation chain transfer) agent in surfactant‐free emulsion polymerization of vinyl acetate to form in situ an amphiphilic block copolymer able to efficiently stabilize the latex particles. The method afforded the preparation of high solids content (27%) latices coated by dextran. Both the kinetic study and the molar mass analyses confirmed the involvement of the dithiocarbonate group in the emulsion polymerization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2845–2857, 2008     

Atom transfer radical polymerization of methyl methacrylate catalyzed by ion exchange resin immobilized Co(II) hybrid catalyst

Ion exchange resin immobilized Co(II) catalyst with a small amount of soluble CuCl₂/Me₆TREN catalyst was successfully applied to atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in DMF. Using this catalyst, a high conversion of MMA (>90%) was achieved. And poly(methyl methacrylate) (PMMA) with predicted molecular weight and narrow molecular weight distribution (M_w/M_n = 1.09–1.42) was obtained. The immobilized catalyst can be easily separated from the polymerization system by simple centrifugation after polymerization, resulting in the concentration of transition metal residues in polymer product was as low as 10 ppm. Both main catalytic activity and good controllability over the polymerization were retained by the recycled catalyst without any regeneration process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1416–1426, 2008     

Living radical polymerization of diisopropyl fumarate to obtain block copolymers containing rigid poly(substituted methylene) and flexible polyacrylate segments

Living radical polymerizations of diisopropyl fumarate (DiPF) are carried out to synthesize poly(diisopropyl fumarate) (PDiPF) as a rigid poly(substituted methylene) and its block copolymers combined with a flexible polyacrylate segment. Reversible addition‐fragmentation chain transfer (RAFT) polymerization is suitable to obtain a high‐molecular‐weight PDiPF with well‐controlled molecular weight, molecular weight distribution, and chain‐end structures, while organotellurium‐mediated living radical polymerization (TERP) and reversible chain transfer catalyzed polymerization (RTCP) give PDiPF with controlled chain structures under limited polymerization conditions. In contrast, controlled polymerization for the production of high‐molecular‐weight and well‐defined PDiPF is not achieved by atom transfer radical polymerization (ATRP) and nitroxide‐mediated radical polymerization (NMP). The block copolymers consisting of rigid poly(substituted methylene) and flexible polyacrylate segments are synthesized by the RAFT polymerization. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2136–2147     

Immobilization of RAFT agents on silica nanoparticles utilizing an alternative functional group and subsequent surface‐initiated RAFT polymerization

Silica–polystyrene core‐shell particles were successfully prepared by surface‐mediated reversible addition fragmentation chain transfer (RAFT) polymerization of styrene monomer from the surfaces of the silica‐supported RAFT agents. Initially, macro‐RAFT agents were synthesized by RAFT polymerization of γ‐methacryloxypropyltrimethoxysilane (MPS) in the presence of chain transfer agents (CTAs). Immobilization of CTAs onto the silica surfaces was then performed by reacting silica with macro‐RAFT agents via a silane coupling. Grafting of polymer onto silica forms core‐shell nanostructures and shows a sharp contrast between silica core and polymer shell in the phase composition. The thickness of grafted‐polymer shell and the diameter of core‐shell particles increase with the increasing ratio of monomer to silica. A control experiment was carried out by conventional free radical emulsion copolymerization of MPS‐grafted silica and styrene under comparable conditions. The resulting data provide further insight into the chemical composition of grafted‐polymers that are grown from the silica surface through RAFT process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 467–484, 2009     

Synthesis and characterization of well‐defined block and statistical copolymers based on lauryl methacrylate and 2‐(acetoacetoxy)ethyl methacrylate using RAFT‐controlled radical polymerization

Four well‐defined diblock copolymers and one statistical copolymer based on lauryl methacrylate (LauMA) and 2‐(acetoacetoxy)ethyl methacrylate (AEMA) were prepared using reversible addition‐fragmentation chain transfer (RAFT) polymerization. The polymers were characterized in terms of molecular weights, polydispersity indices (ranging between 1.12 and 1.23) and compositions by size exclusion chromatography and ¹H NMR spectroscopy, respectively. The preparation of the block copolymers was accomplished following a two‐step methodology: First, well‐defined LauMA homopolymers were prepared by RAFT using cumyl dithiobenzoate as the chain transfer agent (CTA). Kinetic studies revealed that the polymerization of LauMA followed first‐order kinetics demonstrating the “livingness” of the RAFT process. The pLauMAs were subsequently used as macro‐CTA for the polymerization of AEMA. The glass transition (T_g) and decomposition temperatures (ranging between 200 and 300 °C) of the copolymers were determined using differential scanning calorimetry and thermal gravimetric analysis, respectively. The T_gs of the LauMA homopolymers were found to be around ?53 °C. Block copolymers exhibited two T_gs suggesting microphase separation in the bulk whereas the statistical copolymer presented a single T_g as expected. Furthermore, the micellization behavior of pLauMA‐b‐pAEMA block copolymers was investigated in n‐hexane, a selective solvent for the LauMA block, using dynamic light scattering. pLauMA‐b‐pAEMA block copolymers formed spherical micelles in dilute hexane solutions with hydrodynamic diameters ranging between 30 and 50 nm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5442–5451, 2008     

Synthesis of densely grafted comblike copolymers

Densely grafted copolymers were synthesized using the “grafting from” approach via the combination of reversible addition‐fragment chain transfer polymerization (RAFT) and atom transfer radical polymerization (ATRP). First, a novel functional monomer, 2,3‐di(2‐bromoisobutyryloxy)ethyl acrylate (DBPPA), with two initiating groups for ATRP was synthesized. It was then polymerized via RAFT polymerization to give macroinitiators for ATRP with controlled molecular weights and narrow molecular weight distributions. Last, ATRP of styrene was carried out using poly(DBPPA)s as macroinitiators to prepare comblike poly(DBPPA)‐graft‐polystyrenes carrying double branches in each repeating unit of backbone via “grafting from” approach. Furthermore, poly(DBPPA)‐graft‐[polystyrene‐block‐poly(t‐BA)]s and their hydrolyzed products poly(DBPPA)‐graft‐[polystyrene‐block‐poly(acrylic acid)]s were also successfully prepared. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 362–372, 2008     

Oligopeptide‐based amide functional initiators for ATRP

Polymer–peptide conjugates are receiving significant interest. Here, we show that, under the appropriate conditions, a small family of oligopeptide‐based initiators can be used successfully to initiate the polymerization of methacrylic monomers by atom transfer radical polymerization (ATRP), generating new examples of such materials. However, the use of the peptidic amide‐based initiators results in polymers which have a higher molecular weight than expected and a significantly higher polydispersity than those prepared from ester‐based initiators. In many cases significant initiator remains, suggesting that either not all peptides successfully initiate polymerization or that significant termination reactions occur early in the reaction. This low initiator efficiency agrees with other reports for amino acid‐based initiators. It therefore appears that such amide‐based initiators can be used successfully, but have a significantly lower applicability than the more commonly used ester‐based initiators. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6082–6090, 2008     

A novel azo‐containing dithiocarbamate used for living radical polymerization of methyl acrylate and styrene

A novel azo‐containing dithiocarbamate, 1‐phenylethyl N,N‐(4‐phenylazo) phenylphenyldithiocarbamate (PPADC), was successfully synthesized and used to mediate the polymerization of methyl acrylate (MA) and styrene (St). In the presence of PPADC, the reversible addition‐fragmentation chain transfer (RAFT) polymerization was well controlled in the case of MA, however, the slightly ill‐controlled in the case of St. Interestingly, the polymerization of St could be well‐controlled when using PPADC as the initiator in the presence of CuBr/PMDETA via atom transfer radical polymerization (ATRP) technique. In the cases of RAFT polymerization of MA and ATRP of St, the kinetic plots were both of first‐order, and the molecular weight of the polymer increased linearly with the monomer conversion while keeping the relatively narrow molecular weight distribution (M_w/M_n). The molecular weight of the polymer measured by gel permeation chromatographer (GPC) was also close to the theoretical value (M_n(th)). The obtained polymer was characterized by ¹H‐NMR analysis, ultraviolet absorption, FTIR spectra analysis and chain‐extension experiments. Furthermore, the photoresponsive behaviors of azobenzene‐terminated poly(methyl acrylate) (PMA) and polystyrene (PS) were similar to PPADC. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5626–5637, 2008     

Synthesis of arborescent (Dendritic) polystyrenes via controlled inimer‐type reversible addition‐fragmentation chain transfer polymerization

The reversible addition‐fragmentation chain transfer (RAFT) copolymerization of styrene and 4‐vinylbenzyl dithiobenzoate, a RAFT‐based inimer (initiator‐monomer), is described. Controlled polymerization was achieved in bulk conditions using thermal initiation at 110 °C to give arborescent polystyrene (arbPSt). The number‐average molecular weights of the polymers increased linearly with conversion and were much higher than theoretically calculated for a linear polymerization, reaching M_n = 364,000 g/mol with M_w/M_n = 2.65. Branching analysis by NMR showed an average of 3.5 branches per chain. SEC data, which were similar to those measured in arborescent polyisobutylene, supported the architectural analysis. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7621–7627, 2008     

Effect of rate retardation in RAFT grafting polymerization from silicon wafer surface

Polystyrene and poly(butyl acrylate) were grafted from silicon wafer surface by reversible addition‐fragmentation chain transfer (RAFT) polymerization. Three RAFT agents were immobilized onto silicon wafer through their leaving/initiating groups (R group). Grafting polymerization of butyl acrylate (BA) and styrene (St) was then carried out from the immobilized RAFT agents. The immobilization of the RAFT agents and the subsequent grafting polymerization of St and BA were evaluated by ellipsometry and X‐ray photoelectron spectroscopy. It was found that type of monomer, structure of RAFT agent, and local RAFT concentration on the surface have dramatic influences on the thickness of grafted polymer layer. The grafting polymerization with more severe rate retardation effect yielded thinner polymer films on the silicon wafer. Selection of a RAFT agent with little rate retardation was critical in the grafting polymerization to achieve thick films. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 970–978, 2008     

Reverse ATRP process of acrylonitrile in the presence of ionic liquids

An ionic liquid, 1‐butyl‐3‐methylimidazolium tetrafluoroborate ([C₄mim] [BF₄]), was first used as the solvent in azobisisobutyronitrile (AIBN)‐initiated reverse atom transfer radical polymerization (RATRP) of acrylonitrile with FeCl₃/succinic acid (SA) as the catalyst system. The polymerization in [C₄mim][BF₄] proceeded in a well‐controlled manner as evidenced by kinetic studies. Compared with the polymerization in bulk, the polymerization in [C₄mim][BF₄] not only showed the best control of molecular weight and its distribution but also provided rather rapid reaction rate with the ratio of [C₄mim][BF₄] at 200:1:2:4. The polymerization apparent activation energies in [C₄mim][BF₄] and bulk were calculated to be 48.2 and 55.7 kJ mol^?1, respectively. Polyacrylonitrile obtained was successfully used as a macroinitiator to proceed the chain extension polymerization in [C₄mim][BF₄] via a conventional ATRP process. [C₄mim][BF₄] and the catalyst system could be easily recycled and reused after simple purification and had no effect on the living nature of polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2701–2707, 2008