Enhancement of electron-induced X-ray intensity for single particles under grazing-exit conditions

Grazing-exit electron probe microanalysis (GE-EPMA) was performed for single Al₂O₃ and atmospheric particles, deposited on a flat Si substrate coated by gold, by using an aperture (1 mm in diameter) in front of an energy-dispersive X-ray detector. Silicon Kα X-rays from the Si substrate were strongly observed at an exit angle of ∼45°. However, they disappeared at grazing-exit angles about 0° and only the X-rays from particles were detected. Furthermore, Al Kα and O Kα intensities from single Al₂O₃ particle were enhanced approximately three- and sixfold at the grazing-exit angles (∼1°), respectively, in comparison with those at large angle (∼7°). The background intensities at the energy of Al Kα and O Kα almost monotonously decreased with decreasing exit angle. As a result, the intensity ratios of Al Kα and O Kα X-rays to the background intensities were enhanced five- and sixfold, respectively. This enhancement is considered to be caused by the interference effect of both directly detected X-rays and reflected X-rays on the flat substrate. The similar results are also obtained for Al Kα, Si Kα, K Kα and Ca Kα emitted from single atmospheric particle. The significance of the matrix effect in the particle is also pointed out.     

Uniform particles of manganese compounds obtained by forced hydrolysis of manganese(II) acetate

 Procedures for the preparation at low temperature (80 °C) of uniform colloids consisting of Mn₃O₄ nanoparticles (about 20 nm) or elongated α-MnOOH particles with length less than 2 μm and width 0.4 μm or less, based on the forced hydrolysis of aqueous manganese(II) acetate solutions in the absence (Mn₃O₄) or the presence (α-MnOOH) of HCl are described. These solids are only produced under a very restrictive range of reagent concentrations involving solutions of 0.2–0.4 mol dm⁻³ manganese(II) acetate for Mn₃O₄ and of 1.6–2 mol dm⁻³ Mn(II) and 0.2–0.3 mol dm⁻³ HCl for α-MnOOH. The role that the acetate anions play in the precipitation of these solids is analyzed. It seems that these anions promote the oxidation of Mn(II) to Mn(III), which readily hydrolyze causing precipitation. The evolution of the characteristics of the powders with temperature up to 900 °C is also reported. Thus, Mn₃O₄ particles transform to Mn₂O₃ upon calcination at 800 °C; this is accompained by a sintering process. The α-MnOOH sample also experiences several phase transformations on heating. First, it is oxidized at low temperatures (250–450 °C) giving MnO₂ (pyrolusite), which is further reduced to Mn₂O₃ at 800 °C. After this process the particles still retain their elongated shape. Received: 19 October 1999 Accepted: 24 November 1999     

Colloidal hydrolysis products of SbCl3 in acidic solutions

 The hydrolysis of SbCl₃ in hydrochloric acid solution (2.0 mol dm^-3 HCl) at 0 °C yields an amor-phous product consisting of uniform spherical particles (d∼0.5 μm), which on continuous aging at the same temperature transform to larger crystals, indicated by XRD to be Sb₄O₅Cl₂. In contrast, in the same solution kept at 25 °C crystalline particles of the same composition form directly after an induction period and then grow with time. The final products, obtained at 0 °C and 25 °C consist of aggregated subunits. These powders on calcination in nitrogen are converted to Sb₂O₃ and in air to Sb₂O₄. Received: 23 June 1997 Accepted: 1 July 1997     

Localized thin-film analysis by grazing-exit electron probe microanalysis

We have studied the application of grazing-exit electron probe microanalysis (GE-EPMA) for surface and thin-film analysis. In this method, characteristic X-rays are measured at small take-off angles of less than 1°. Under grazing-exit conditions, the X-rays emitted from deep inside the sample are not detected because they are stopped by a slit mounted in front of the energy-dispersive X-ray detector. Hereby, it becomes possible to perform localized surface analysis with GE-EPMA. We applied this method to thin-film analysis of a small surface area. The exit-angle dependence of the characteristic X-ray intensities was measured for thin films of Cr and Ti. Thickness and density of thin films were determined by fitting the experimental plots with theoretically calculated curves. Differences were found in the densities of two Cr thin films deposited by magnetron sputtering and vacuum evaporation. The advantage of GE-EPMA is that non-destructive thin-film analysis of small surface areas can be incorporated in simple scanning electron microscope (SEM) analysis.     

Crystal Structure and Conformation of a 10-Thiabilirubin

 A crystal structure determination of a bilirubin analog with a sulfur instead of a C(10)–CH₂ linking the two dipyrrinones is reported. Conformation-determining torsion angles and key hydrogen bond distances and angles are compared to those obtained from molecular dynamics calculations as well as to the corresponding data from X-ray determinations and molecular dynamics calculations of bilirubin. Like other bilirubins, the component dipyrrinones of the analog are present in the bis-lactam form with (Z)-configurated double bonds at C(4) and C(15). Despite the large differences in bond lengths and angles at –S–vs.–CH₂–, the crystal structure shows considerable similarity to bilirubin: both pigments adopt a folded, intramolecularly hydrogen-bonded ridge-tile conformation stabilized by six hydrogen bonds – although the interplanar angle of the ridge-tile conformation of the title compound is smaller (∼ 86°) than that of bilirubin (∼ 98°). The collective data indicate that even with long C–S bond lengths and a smaller C–S–C bond angle at the pivot point on the ridge-tile seam, intramolecular hydrogen bonding persists.     

Preparation and characterization of multiresponsive polymer composite microspheres with core–shell structure

Fe₃O₄/SiO₂/poly (N-isopropylacrylamide-co-N,N-dimethylaminoethyl methacrylate) [P(NIPAM-co-DMA)] multiresponsive composite microspheres with core–shell structure were synthesized by template precipitation polymerization. First, the magnetite nanoparticles were coated with silica and then modified with 3-(trimethoxysilyl)-propyl methacrylate (MPS). Subsequently, the Fe₃O₄/SiO₂ particles grafted with MPS were used to seed the precipitation copolymerization of NIPAM and DMA. The composite microspheres with core–shell structure were superparamagnetic, pH-sensitive, and thermoresponsive. The swelling ratio (D_{25 °C, pH = 3}/D_{50 °C, pH = 9})³ coupling of pH and temperature increased up to 21.2, which was much higher than that without comonomer DMA.     

A novel coprecipitation method towards the synthesis of Ni<Subscript>x</Subscript>Mn<Subscript>x</Subscript>Co<Subscript>(1–2x)</Subscript>(OH)<Subscript>2</Subscript> for the preparation of lithium metal oxides

A series of mixed metal hydroxide (Ni _x Mn _x Co_(1–2x)(OH)₂) precursors for the preparation of lithiated mixed metal oxides (LiNi _x Mn _x Co_(1–2x)O₂) were prepared using a novel coprecipitation approach based on the thermal decomposition of urea. Three different methods were used to achieve the temperature required to decompose urea and subsequently precipitate the hydroxides. The first two methods consisted of either a hydrothermal or microwave-assisted hydrothermal synthesis at 180 °C and elevated pressures. The final method was an aqueous reflux at 100 °C. A complete series (x = 0.00–0.50) was prepared for each method and fully characterized before and after converting the materials to lithiated metal oxides (LiNi _x Mn _x Co_(1–2x)O₂). We observed the formation of a complex structure after the coprecipitation of the hydroxides. Scanning electron micrographs images demonstrate that the morphology and particle size of the hydroxide particles varied significantly from x = 0.00–0.50 under hydrothermal synthesis conditions. There is also a significant change in particle morphology as the urea decomposition method is varied. The X-ray diffraction profiles of the oxides synthesized from these hydroxide precursors all demonstrated phase pure oxides that provided good electrochemical performance.     

Sensitive fluorescent probes for determination of hydrogen peroxide and glucose based on enzyme-immobilized magnetite/silica nanoparticles

Sensitive fluorescent probes for the determination of hydrogen peroxide and glucose were developed by immobilizing enzyme horseradish peroxidase (HRP) on Fe₃O₄/SiO₂ magnetic core–shell nanoparticles in the presence of glutaraldehyde. Besides its excellent catalytic activity, the immobilized enzyme could be easily and completely recovered by a magnetic separation, and the recovered HRP-immobilized Fe₃O₄/SiO₂ nanoparticles were able to be used repeatedly as catalysts without deactivation. The HRP-immobilized nanoparticles were able to activate hydrogen peroxide (H₂O₂), which oxidized non-fluorescent 3-(4-hydroxyphenyl)propionic acid to a fluorescent product with an emission maximum at 409 nm. Under optimized conditions, a linear calibration curve was obtained over the H₂O₂ concentrations ranging from 5.0 × 10⁻⁹ to 1.0 × 10⁻⁵ mol L⁻¹, with a detection limit of 2.1 × 10⁻⁹ mol L⁻¹. By simultaneously using glucose oxidase and HRP-immobilized Fe₃O₄/SiO₂ nanoparticles, a sensitive and selective analytical method for the glucose detection was established. The fluorescence intensity of the product responded well linearly to glucose concentration in the range from 5.0 × 10⁻⁸ to 5.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 1.8 × 10⁻⁸ mol L⁻¹. The proposed method was successfully applied for the determination of glucose in human serum sample.     

The NiFe2O4 - MgFe2O4 series as electrode materials for electrochemical reduction of NO x

Solid solutions of spinel-type oxides with the composition (x = 0.0, 0.3, 0.5, 0.6, 1.0) were prepared with the glycine-nitrate combustion synthesis (x = 0.0, 0.3, 0.5, 0.6) and the citric-acid combustion synthesis (x = 1.0). The oxides were used as electrode materials in a pseudo-three-electrode setup in the temperature range of 400–600 °C. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the electrochemical behavior in 1% NO and 10% O₂. Measurements show that NiFe₂O₄ has relatively high cathodic activity in both NO and O₂, whereas MgFe₂O₄ shows much higher activity in NO compared to O₂. MgFe₂O₄ was also measured with cyclic voltammetry in 1% NO₂ and different gas mixtures of NO and O₂ at 300 and 400 °C. Results show that the cathodic activities (−0.6 V) are relatively high with current ratios, , ranging from 10.1–167.7 and with a maximum at 400 °C. Dilatometry measurements were performed on the materials in air up to 1,000 °C, and they showed that the Curie temperature could be detected for all samples. Four-point DC resistivity measurements at elevated temperatures show that Ni_0.4Mg_0.6Fe₂O₄ has the highest conductivity, whereas Ni_0.7Mg_0.3Fe₂O₄ and NiFe₂O₄ have the highest conductivity at lower temperatures.     

Solubility of Zinc Silicate and Zinc Ferrite in Aqueous Solution to High Temperatures

Crystalline zinc silicate, Zn₂SiO₄, and zinc ferrite, ZnFe₂O₄, were prepared and characterized. The solubilities of these phases were measured using flow-through apparatus from 50 to 350 °C in 100 °C intervals over a wide range of pH. Both solid phases dissolve incongruently, presumably to form ZnO(s) and Fe₂O₃(s) (or the corresponding hydroxide phases at low temperature), respectively. The respective concentrations of zinc(II) and iron(III) matched those of ZnO(cr) and Fe₂O₃(s) (≥150 °C) reported in the literature, whereas the corresponding Si(IV) and Zn(II) concentrations were at least an order of magnitude below the solubility limits for their pure oxide phases. Therefore, the solubility constants for zinc silicate and ferrite were determined with respect to the known solubility constants for ZnO(cr) and Fe₂O₃(s) (≥150 °C), respectively, and the corresponding concentrations of Si(IV) and Zn(II) measured in this study. The results of independent experiments, as well as those reported in the literature provide insights into the mechanism(s) of formation of zinc silicate and ferrite in the primary circuits of nuclear reactors. D.A. Palmer is retired.     

Crystal Structure and Characterisation of Mercury(II) Dichromate(VI)

Dark-red single crystals of HgCr₂O₇ were grown by reacting HgO and CrO₃ in excess at 200°C for four days. The crystal structure (space group P3₂, Z = 3, a = 7.2389(10), c = 9.461(2) ?, 1363 structure factors, 57 parameters, R[F ²>2σ(F ²)] = 0.0369, wR(F ² all) = 0.0693) was determined from a crystal twinned by merohedry according to (110). It consists of nearly linear HgO₂ units ( [`(d)]{\bar {d}} (Hg–O) = 2.02 ?) and dichromate units that are linked into infinite chains ‘O₃Cr–O–CrO₃–Hg–O₃Cr–O–CrO₃’ running parallel to the c-axis. Six additional Hg–O contacts between 2.73 and 2.96 ? stabilise the structural arrangement. The dichromate anion exhibits a staggered conformation with a bent Cr–O–Cr bridging angle of 140.7(6)°. Upon heating above 300°C, HgCr₂O₇ decomposes in a two-step mechanism to Cr₂O₃. The title compound was additionally characterised by vibrational spectroscopy.     

A new amperometric H<Subscript>2</Subscript>O<Subscript>2</Subscript> biosensor based on nanocomposite films of chitosan–MWNTs,hemoglobin, and silver nanoparticles

A new H₂O₂ biosensor was fabricated on the basis of nanocomposite films of hemoglobin (Hb), silver nanoparticles (AgNPs), and multiwalled carbon nanotubes (MWNTs)–chitosan (Chit) dispersed solution immobilized on glassy carbon electrode (GCE). The immobilized Hb displayed a pair of well-defined and reversible redox peaks with a formal potential (E ^θ′) of −22.5 mV in 0.1 M pH 7.0 phosphate buffer solution. The apparent heterogeneous electron transfer rate constants (k _s) in the Chit–MWNTs film was evaluated as 2.58 s⁻¹ according to Laviron’s equation. The surface concentration (Γ*) of the electroactive Hb in the Chit–MWNTs film was estimated to be (2.48 ± 0.25) × 10⁻⁹ mol cm⁻². Meanwhile, the Chit–MWNTs/Hb/AgNPs/GCE demonstrated excellently electrocatalytical ability to H₂O₂. Its apparent Michaelis–Menten constant (K _M^app) for H₂O₂ was 0.0032 mM, showing a good affinity. Under optimal conditions, the biosensors could be used for the determination of H₂O₂ ranging from 6.25 × 10⁻⁶ to 9.30 × 10⁻⁵ mol L⁻¹ with a detection limit of 3.47 × 10⁻⁷ mol L⁻¹ (S/N = 3). Furthermore, the biosensor possessed rapid response to H₂O₂ and good stability, selectivity, and reproducibility.     

Electrochemical properties of perovskite and A<Subscript>2</Subscript>MO<Subscript>4</Subscript>-type oxides used as cathodes in protonic ceramic half cells

Three selected materials have been prepared and shaped as cathode of half cells using the proton-conducting electrolyte BaCe_0.9Y_0.1O_3 − δ (BCY10): two perovskite compounds, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 − δ (BSCF) and La_0.6Sr_0.4Fe_0.8Co_0.2O_3 − δ (LSFC), and the praseodymium nickelate Pr₂NiO_4 + δ (PRN) having the K₂NiF₄-type structure. The electrochemical properties of these compounds have been studied under zero current conditions (two-electrode cell) and under polarization (three-electrode cell). Their measured area-specific resistances were about 1–2 Ω cm² at 600 °C. Under direct current polarization, it appears that the three compounds show almost similar values of current densities at 625 °C; however, at lower temperatures, BSCF appears to be the most efficient cathode material.     

Preparation of Cr2O3-Al2O3 Solid Solutions by Reactive Magnetron Sputtering

 (Al,Cr)₂O₃ layers were deposited on cemented carbide insert tips at a substrate temperature of 500 °C by means of reactive magnetron sputtering. An Al target was sputtered in RF mode and a Cr target in DC mode simultaneously in an oxygen/argon plasma. The influence of the Al and Cr sputter power and of the oxygen partial pressure on composition and structure of the (Al,Cr)₂O₃ layers as well as on the binding states of their components were investigated. Special attention was paid to the interpretation of the O ls and O-KLL fine structure and peak shifts. For the binary phases γ-Al₂O₃ and Cr₂O₃, a good agreement with literature values was observed in each case. In case of the ternary phases a continuous shift of the energetic position of the O1s peak, the O-KL₂₃L₂₃ transition and the modified Auger parameter α ′ of oxygen between the two binary phases γ-Al₂O₃ and Cr₂O₃ could be detected, indicating a wide range of solid solubility between Al₂O₃ and Cr₂O₃. As revealed by grazing incidence X-ray diffraction, the crystallinity of the ternary phases is less pronounced as compared to the binaries and increases with increasing oxygen flow rate.     

Structure and Magnetic Properties of Nickel–Zinc Ferrite Nanoparticles Prepared by Glass Crystallization Method

The magnetic and microstructure properties of Fe₂O₃–0.4NiO–0.6ZnO–B₂O₃ glass system, which was subjected to heat treatment in order to induce a magnetic crystalline phase (Ni_0.4Zn_0.6-Fe₂O₄ crystals) within the glass matrix, were investigated. DSC measurement was performed to reveal the crystallization temperature of the prepared glass sample. The obtained samples, produced by heat treatment at 765°C for various times (1, 1.5, 2, and 3 h), were characterized by X-ray diffraction, IR spectra, transmission electron microscopy, and vibrating sample magnetometer. The results indicated the formation of spinel Ni–Zn ferrite in the glass matrix. Particles of the ferrite with sizes ranging from 28 to 120 nm depending on the sintering time were observed. The coercivity values for different heat-treatment samples were found to be in the range from 15.2 to 100 Oe. The combination of zinc content and sintering times leads to samples with saturation magnetization ranging from 12.25 to 17.82 emu/g.     

Crystal Structure and Characterisation of Mercury(II) Dichromate(VI)

Summary. Dark-red single crystals of HgCr₂O₇ were grown by reacting HgO and CrO₃ in excess at 200°C for four days. The crystal structure (space group P3₂, Z = 3, a = 7.2389(10), c = 9.461(2) ?, 1363 structure factors, 57 parameters, R[F ²>2σ(F ²)] = 0.0369, wR(F ² all) = 0.0693) was determined from a crystal twinned by merohedry according to (110). It consists of nearly linear HgO₂ units ( (Hg–O) = 2.02 ?) and dichromate units that are linked into infinite chains ‘O₃Cr–O–CrO₃–Hg–O₃Cr–O–CrO₃’ running parallel to the c-axis. Six additional Hg–O contacts between 2.73 and 2.96 ? stabilise the structural arrangement. The dichromate anion exhibits a staggered conformation with a bent Cr–O–Cr bridging angle of 140.7(6)°. Upon heating above 300°C, HgCr₂O₇ decomposes in a two-step mechanism to Cr₂O₃. The title compound was additionally characterised by vibrational spectroscopy.     

Preparation and performance comparison of LiMn2O3.95Br0.05 and LiMn2O3.95Br0.05/SiO2 cathode materials for lithium-ion battery

LiMn₂O_3.95Br_0.05 and LiMn₂O_3.95Br_0.05/SiO₂ cathode composites for lithium-ion battery are prepared by solid-state reaction methods. The crystalline structures of the as-synthesized samples are investigated by X-ray diffraction and transmission electron microscope; at the same time, the electrochemical performances are tested by cyclic voltammetry and galvanostatic cycling. The results reveal that the sample of LiMn₂O_3.95Br_0.05/SiO₂ has more excellent electrochemical performance than the sample of LiMn₂O_3.95Br_0.05. It delivers an initial discharge capacity of 145.3 mA h g⁻¹ at ambient temperature, and 138.9 mA h g⁻¹ at the higher temperature of 55 °C with good capacity retention with the voltage range of 3.0–4.35 V (vs. Li) at a current density of 0.5 C; while the sample of LiMn₂O_3.95Br_0.05 only deliver initial discharge capacity 136.5 mA h g⁻¹ at ambient temperature, and 119.2 mA h g⁻¹ at 55 °C in the same conditions; in addition, the rate performance of LiMn₂O_3.95Br_0.05/SiO₂ is excellent too, so the SiO₂ layer has improved the electrochemical behaviors of LiMn₂O_3.95Br_0.05 availably.     

Bi5Nb3O15 as a photocatalyst: photocatalytic and photoelectrochemical studies

Bi₅Nb₃O₁₅ was prepared from a stoichiometric mixture of Bi₂O₃ and Nb₂O₅ at 300–500 °C. The prepared photocatalyst was characterized by diffuse reflection spectrum (DRS), X-ray diffraction (XRD), scanning electron microscopy (SEM) and particle size analysis. The band gap, crystal structure and average grain size were determined from the above methods to be 3.25 eV, distorted pyrochlore and 4–5 μm respectively. The photoelectrochemical behavior of hydrogen-reduced Bi₅Nb₃O₁₅ was investigated in 0.1 M Na₂SO₄ and using the Fe(CN)₆ ^3−/4− redox couple for measuring the current-voltage characteristics. The cyclic voltammetric studies revealed that the onset potential for photocurrent generation existed at −0.45 V, which is more negative to water reduction level at pH 7.0, and that of the photocurrent at 1.0 V was observed as 0.58 mA/cm². Photocatalytic hydrogen production has been achieved by using Bi₅Nb₃O₁₅ as a photocatalyst in presence of methyl viologen. The quantum yield for hydrogen production for this system was found to be 0.83. All the studies clearly indicated that Bi₅Nb₃O₁₅ has potential in solar energy conversion. Received: 22 May 1997 / Accepted: 18 September 1997     

Electrochemical synthesis of Fe3O4-PB nanoparticles with core-shell structure and its electrocatalytic reduction toward H2O2

The Fe₃O₄-Prussian blue (PB) nanoparticles with core-shell structure have been in situ prepared directly on a nano-Fe₃O₄-modified glassy carbon electrode by cyclic voltammetry (CV). First, the magnetic nano-Fe₃O₄ particles were synthesized and characterized by X-ray diffraction. Then, the properties of the Fe₃O₄-PB nanoparticles were characterized by CV, electrochemical impedance spectroscopy, and superconducting quantum interference device. The resulting core-shell Fe₃O₄-PB-modified electrode displays a dramatic electrocatalytic ability toward H₂O₂ reduction, and the catalytic current was a linear function with the concentration of H₂O₂ in the range of 1 × 10⁻⁷~5 × 10⁻⁴ mol/l. A detection limit of 2 × 10⁻⁸ (s/n = 3) was determined. Moreover, it showed good reproducibility, enhanced long-term stability, and potential applications in fields of magnetite biosensors.     

Immobilization of Hemoglobin on the Gold Colloid Modified Pretreated Glassy Carbon Electrode for Preparing a Novel Hydrogen Peroxide Biosensor

A novel hydrogen peroxide (H₂O₂) biosensor was developed by immobilizing hemoglobin on the gold colloid modified electrochemical pretreated glassy carbon electrode (PGCE) via the bridging of an ethylenediamine monolayer. This biosensor was characterized by UV-vis reflection spectroscopy (UV-vis), electrochemical impendence spectroscopy (EIS) and cyclic voltammetry (CV). The immobilized Hb exhibited excellent electrocatalytic activity for hydrogen peroxide. The Michaelis–Menten constant (K _m) was 3.6 mM. The currents were proportional to the H₂O₂ concentration from 2.6 × 10⁻⁷ to 7.0 × 10⁻³ M, and the detection limit was as low as 1.0 × 10⁻⁷ M (S/N = 3).