穿透短裂纹扩展趋偏现象的模型分析和实验研究

本文揭示了穿透短裂纹疲劳扩展中的一个特性－趋偏扩展特性。这一特性是穿透短裂纹预测和测试中产生偏问题的根本原因。通过对长、短裂纹扩展特性及主要影响因素的分析，提出了进行穿透短裂纹试验时必须注意的若干事项。     

高温疲劳表面短裂纹的分形研究

对2.25Cr-1Mo合金钢进行了高温疲劳实验，采用中断试验与复膜技术相结合的方法观测了试样表面疲劳短裂纹萌生，扩展及合体的演化过程，并用数据格子方法研究了含裂纹表面的分形特征。结果表明：疲劳短裂纹的萌生扩展行为具有分形特征，可以用分形理论加以描述；分形维数随着疲劳过程的继续而稳定地成比例增加；分形维数可以作为把握材料总体损伤状态的参数，可作为寿命评价的依据。     

狭长缺口根部萌生的小裂纹扩展分析

根据伴随着小裂纹延展过程中不同力学参数相互作用的分析研究基础之上,我们就疲劳小裂纹的扩展特性进行了分析,根据不扩展裂纹性质对小裂纹的长度范围进行了讨论,探讨了狭长缺口根部萌生的小裂纹扩展速率, 并研究了不扩展裂纹形成机理,推演出不扩展裂纹长度计算方法,发展出一种预测小裂纹扩展行为的方法,借助这种方法可以实现裂纹萌生寿命的预测,与疲劳设计相结合可以进一步提高构件安全性与可靠性．不扩展小裂纹的长度可以通过计算定量得到,它与材料的疲劳极限、裂纹门槛值及缺口尺寸等参数紧密相关．以理论数据为依据,可以设计出针对一定材料及尺寸的试样,使其在一定荷载条件下不扩展裂纹长度达到宏观可观测的范围,进而降低小裂纹测量方面的技术难度,进一步验证不扩张裂纹形成机理．     

35CrMo合金钢疲劳短裂纹扩展规律的试验研究

本文通过试验研究了35CrMo 合金钢三点弯曲试样疲劳短裂纹的扩展特性;用电测法得到了裂尖处的载荷—应变标定关系。试验结果表明,短裂纹的扩展速率正比于局部应力幅的幂次和裂纹长度,即 da/dN=A(?),可以较好地描述疲劳短裂纹的扩展规律。     

冷喷涂试件疲劳裂纹扩展规律试验研究

冷喷涂作为一种新兴的表面处理技术,广泛应用于增材制造和零部件修复等领域。为了探究冷喷涂处理后Q355钢基体的疲劳裂纹扩展规律,对2组标准单边缺口3点弯曲试样进行了冷喷涂处理。在光滑的Q355B钢基材表面分别沉积了纯Al和A5052铝合金涂层,然后对冷喷涂试件和一组未喷涂光滑试件进行了3点弯曲疲劳试验,得到了裂纹尖端张开位移和裂纹长度、裂纹扩展速率和荷载循环次数的规律曲线并进行了对比分析。结果表明：在裂纹扩展长度相同的情况下,冷喷涂试件和未喷涂试件的裂纹尖端张开位移基本相同,且随着疲劳裂纹的延伸,裂纹尖端张开位移也随之快速增大;在一定的裂纹尖端张开位移范围内,冷喷涂处理可以降低疲劳裂纹扩展速率;采用裂纹尖端张开位移作为疲劳裂纹扩展控制参数对冷喷涂试件的疲劳裂纹扩展规律进行判定是准确的,且裂纹尖端张开位移通过试验容易获得,简单方便,可以同时满足裂纹尖端弹性和塑性的情况。     

干态下车轮材料表面疲劳裂纹萌生试验研究

利用WR-1轮轨滚动磨损试验机,结合安定极限理论研究了干态下影响车轮材料表面疲劳裂纹萌生与扩展的因素,探究了表面疲劳损伤形成机理和演变规律.结果表明:随垂向力、横向力和冲角增大,表面疲劳裂纹越容易萌生扩展;冲角对表面疲劳裂纹的萌生与扩展起着重要作用,大冲角下斜线状表面疲劳裂纹萌生扩展明显;只有横向力而不存在冲角时,试样表面不会出现斜线状表面疲劳损伤;车轮试样在周期性循环载荷作用下在表面先形成塑性流动,然后沿轮轨表面切向力方向扩展成斜线状的表面疲劳起皮剥落损伤;垂向力是影响表面裂纹萌生时间的重要因素之一.     

弯曲疲劳短裂纹扩展规律研究

本文对３５ＣｒＭｏ钢和４２ＣｒＭｏ钢带穿透短裂纹（初始裂纹长度ａ＝０．１～０．５ｍｍ）的试件进行了弯曲疲劳试验研究，得到了在弯曲疲劳加载下短裂纹扩展速率的计算表达式以及应力比，试件厚度对短裂纹扩展的影响。     

Ⅱ型裂纹疲劳扩展中超载行为的研究

利用铝合金ＬＹ１２ＣＺ制十字型试样进行Ⅱ型裂纹的疲劳扩展试验，施加若干次短瞬的Ⅱ型超载。发现Ⅱ型裂纹的超载行为与Ⅰ型裂纹的不同，裂纹的扩展速率可几倍于未超载时相同应力强度因子幅度下的扩展速率；而且超载后的短瞬期间，裂纹在塑性区内仍保持较快的速率扩展。试验研究表明：Ⅱ型超载和Ⅰ型超载也许分别受不同的机制控制；它更类似于Ⅲ型超载。     

CrMoW转子钢高温超高周裂纹扩展及疲劳行为研究

本文研究了超超临界汽轮机CrMoW转子钢在常温与600℃条件下的超高周旋转弯曲疲劳行为。实验中利用位移传感器原位监测试件挠度变化,研究裂纹的萌生与扩展特性。研究结果发现,在常温下,疲劳裂纹主要萌生于试样表面,但也发现超高周次疲劳破坏的裂纹萌生于内部的情形。600℃时,S-N曲线呈现直线下降的趋势;大多试样裂纹萌生区和初始扩展区发现非金属夹杂物,其裂纹萌生是表面裂纹起源和亚表面夹杂物相耦合的结果。裂纹萌生寿命占整个疲劳寿命的90%以上,裂纹萌生寿命百分比(Ni/Nf)随疲劳寿命的延长而增大,并且温度对裂纹萌生寿命百分比没有影响。     

试验确定自增强圆筒的表面裂纹K1因子和疲劳扩展规律

本文提供了一种可以进行自增强处理的圆筒试样,通过实验用柔度法确定了该试样的表面裂纹的应力强度因子,介绍了含表面裂纹试样的柔度测试技术,导出了柔度与表面裂纹尖端前缘各点的应力强度因子的关系式,该式可作为各种含表面裂纹试样柔度法测表面裂纹 K_1因子的参考,本文还测定了不同自增强程度下,自增强圆筒的表面裂纹疲劳扩展规律。     

STUDY ON THE SURFACE CRACK GROWTH BEHAVIOR IN 14MnNbq BRIDGE STEEL

Three-dimensional crack closure correction methods are investigated in this paper.The fatigue crack growth tests of surface cracks in 14MnNbq steel for bridge plate subjected to tensile and bending loadings are systematically conducted.The experimentally measured fatigue crack growth rates of surface cracks are compared with those of through-thickness cracks in detail.It is found that the crack growth rates of surface cracks are lower than those of through-thickness cracks.In order to correct their differences in fatigue crack growth rates, a dimensionless crack closure correction model is proposed.Although this correction model is determined only by the experimental data of surface cracks under tensile loading with a constant ratio R=0.05, it can correlate the surface crack growth rates with reasonable accuracy under tensile and bending loadings with various stress ratios ranging from 0 to 0.5.Furthermore, predictions of fatigue life and crack aspect ratio for surface cracks are discussed, and the predicted results are also compared with those obtained from other prediction approaches.Comparison results show that the proposed crack closure correction model gives better prediction of fatigue life than other models.     

焊趾表面裂纹的形态发展曲线与疲劳寿命预测

以作者建立的焊地椭圆表面裂纹应力强度因子数据库以及复杂应力场中焊践半随圆表面裂纹前缘应力强度因子分布计算的基本模式法为基础上,给出了复杂应力场中焊践表面表纹在疲劳扩展过程中形态变化规律及寿命的工程分析方法。     

缺口件疲劳寿命分布预测的有效应力法

本文提出了一种由光滑件疲劳寿命试验数据预测缺口件疲劳寿命分布的有效应力法。该方法中缺口件的裂纹可能萌生表面被分解成一个个微元,整个表面可看成是这些微元组成的一个串联模型,按照串联概率失效模型,缺口件的疲劳强度失效概率就可以由各微元的疲劳强度失效概率计算得到,其中微元的疲劳强度失效概率是由光滑件的疲劳强度失效概率通过最弱环节理论计算得到的。在缺口件的疲劳强度失效概率表达式中,引入了有效应力的概念,用它查取光滑件的疲劳寿命试验数据就可以直接得到缺口件的疲劳寿命分布。该方法可以同时考虑到应力梯度和试件尺寸对缺口件疲劳寿命分布的影响。进行了材料LY12CZ的带中心孔缺口件的寿命算例分析,预测结果和试验结果吻合良好,表明该方法是有效的。     

Fracture of Edge Cracked Layered Plates Subjected to In-plane Bending

Layered structures are used in protection systems such as personal and heavy armor, windshields and also in functionally graded thermal barriers. The focus of this study is to understand the behavior of cracks in such systems, especially when the crack orientation is such that there are property changes along the crack front. Layered plates were prepared by bonding together sheets of epoxy and Polymethylmethacrylate (PMMA) using an epoxy adhesive. Among the two, epoxy has higher elastic modulus and lower fracture toughness compared to PMMA. Two different layer configurations; a single sheet of epoxy bonded to a single PMMA sheet (two layer) and a single sheet of epoxy sandwiched between two PMMA sheets (three layer) were considered. Single edge notched specimens were loaded in three point bending and the thickness averaged stress intensity factor (SIF) was estimated through photoelasticity. Subsequently, the behavior of crack-extension in these plates was also investigated. In both configurations, crack growth initiated in the epoxy layer first and extended stably before the start of crack extension in the PMMA layer. Once the crack extension started in the PMMA layer, the plate looses its structural integrity. It was observed that the onset of crack extension in the epoxy layer can be predicted using the thickness averaged SIF. A method using analysis of patched cracks is presented for estimating the load at which the plate completely looses its load carrying capacity. The estimates from this method match well with experimental results.     

Periodic system of collinear cracks in an elastic porous medium

We consider a problem for cracks in a specific porous elastic material described by the Cowin-Goodman-Nunziato model. For an arbitrary set of collinear cracks, the problem is reduced to an integral equation over the crack surface. In the special case of a periodic crack arrangement, the kernel of the integral equation is written in the form of a Fourier series. By explicitly summing the leading part of the kernel, we can show that it exhibits hypersingular behavior as the argument tends to zero. Further, we solve the main integral equation by using the direct numerical method proposed in our preceding paper. In conclusion, we study the stress concentration at the crack tips and compare this case with the case of a single isolated crack.     

含缺口试件疲劳全寿命预测一种建议的方法

传统的研究含缺口构件的疲劳的方法是将疲劳启裂和疲劳裂纹扩展两个过程完全独立起来,用不同的方法来模拟,相互间并没有定量的关系。本文是基于最新发展的多轴疲劳损伤理论,建立了一种适用于各种载荷条件下的疲劳启裂和裂纹扩展的普适方法。根据从弹塑性分析中得到的应力应变,确定疲劳损伤模型,建立能够预测疲劳启裂、裂纹扩展速率和扩展方向的新方法。整个模拟可以分为两步:弹-塑性应力分析得到材料的应力应变分布;再运用一个通用的疲劳准则预测疲劳裂纹启裂和裂纹扩展。通过对1070号钢含缺口试件的疲劳全寿命预测,得到了与实验非常吻合的模拟结果。     

Fatigue crack growth behavior of Al7050-T7451 attachment lugs under flight spectrum variation

This paper discusses an analytical and experimental investigations of the fatigue crack growth behavior in attachment lugs subjected to a randomized flight-by-flight spectrum. In the analysis, the stress intensity factors for through-the-thickness cracks initiating from lug holes were compared by weight function method, boundary element method (BEM), the interpolation of Brussat’s solution. The stress intensity factors of a corner crack at a transition region were obtained using two parameter weight function method and correction factors. Fatigue life under a load spectrum was predicted using stress intensity factors and Willenborg retardation model considering the effects of a tensile overload. Experiments were performed under a load spectrum and compared with the fatigue life prediction using the stress intensity factors by different methods. Changes of fatigue life and aspect ratio according to the clipping level of the spectrum were discussed through experiment and prediction. Effect of the spectrum clipping level on the fatigue life was experimentally evaluated by using beach marks of fractured surface.     

Pressure effects and fracture of a rubbery particulate composite

The effects of pressure on the fracture properties of a rubbery particulate composite are studied. The results indicate elevated fracture toughness values and lower crack growth rates relative to ambient pressure conditions. The regression method employed for determining toughness establishes a minimum thickness requirement for application of linear elastic fracture mechanics concepts. Also, it is demonstrated that single edge notched tension specimens can be successfully used to predict the fracture initiation of specimens with semielliptical surface cracks.     

The behavior of permeable multi-cracks in a piezoelectric material

In this paper, the behavior of four parallel symmetric cracks in a piezoelectric material under anti-plane shear loading is studied by the Schmidt method for the permeable crack surface boundary conditions. By use of the Fourier transform, the problem can be solved with the help of two pairs of triple integral equations that the unknown variables are the jumps of the displacement across the crack surfaces. These equations are solved by means of the Schmidt method. The results show that the stress and the electric displacement intensity factors of cracks depend on the geometry of the crack. Contrary to the impermeable crack surface condition solution, it is found that the electric displacement intensity factors for the permeable crack surface conditions are much smaller than the results for the impermeable crack surface conditions.     

THE BEHAVIOR OF TWO PARALLEL SYMMETRIC PERMEABLE CRACKS IN PIEZOELECTRIC MATERIALS

ＩｎｔｒｏｄｕｃｔｉｏｎＩｔｉｓｗｅｌｌ＿ｋｎｏｗｎｔｈａｔｐｉｅｚｏｅｌｅｃｔｒｉｃｍａｔｅｒｉａｌｓｐｒｏｄｕｃｅａｎｅｌｅｃｔｒｉｃｆｉｅｌｄｗｈｅｎｄｅｆｏｒｍｅｄａｎｄｕｎｄｅｒｇｏｄｅｆｏｒｍａｔｉｏｎｗｈｅｎｓｕｂｊｅｃｔｅｄｔｏａｎｅｌｅｃｔｒｉｃｆｉｅｌｄ .Ｔｈｅｃｏｕｐｌｉｎｇｎａｔｕｒｅｏｆｐｉｅｚｏｅｌｅｃｔｒｉｃｍａｔｅｒｉａｌｓｈａｓａｔｔｒａｃｔｅｄｗｉｄｅａｐｐｌｉｃａｔｉｏｎｓｉｎｅｌｅｃｔｒｉｃ＿ｍｅｃｈａｎｉｃａｌａｎｄｅｌｅｃｔｒｉｃｄｅｖｉｃｅｓ,ｓｕｃ…