Evidence for the existence of an effective interfacial tension between miscible fluids. 2. Dodecyl acrylate-poly(dodecyl acrylate) in a spinning drop tensiometer

We studied drops of dodecyl acrylate in poly(dodecyl acrylate) (molecular weight of 25,000) in a spinning drop tensiometer to determine whether an effective interfacial tension (EIT) existed between these two miscible fluids. We found convincing evidence. We estimated the mechanical relaxation time from an immiscible analogue (1-propanol and poly(dodecyl acrylate)) and showed that the dodecyl acrylate drops maintained quasi-steady diameters long after this relaxation period. Drops continuously grew in length and became more diffuse, but the width of the transition zone did not grow with t(1/2) as expected from Fick's law although this system had been shown to follow Fick's law in a static configuration (Antrim, D.; Bunton, P.; Lewis, L. L.; Zoltowski, B. D.; Pojman, J. A. J. Phys. Chem. B 2005, 109, 11842-11849). The EIT was determined from Vonnegut's equation, EIT = (Deltarho)omega(2)r(3)/4; both the inner and outer diameters were measured, yielding values of 0.002 and 0.02 mN m(-1), respectively. The EIT was found to be independent of the rotation rate above 6000 rpm and independent of the initial drop volume. The EIT was found to decrease with temperature and increase with the difference in concentration between the monomer drop and polymer-monomer fluid. The square gradient parameter, k, was determined from EIT = k(Deltac(2)/delta), where Deltac is the difference in mole fraction and delta is the width of the transition zone. The square gradient parameter was on the order of 10(-9) N. The square gradient parameter was found to decrease with temperature, to be independent of concentration, and to increase with the molecular weight of the polymer.     

Diffusive desorption of small solute molecules from amorphous polymers: poly(methyl methacrylate), poly (vinyl acetate) and poly(n-alkyl 2-cyanoacrylates)

Diffusion coefficients of some aromatic substances in poly(vinyl acetate) and poly(methyl methacrylate) have been measured from desorption rates into aqueous buffers from solid solutions of diffusant in cast polymer films. With ordinary spectrophotometric instrumentation, extension of the measurable range of the diffusion coefficient at infinite dilution to below 10^?21 m² sec^?1 is sometimes possible. Measures values below 10^?12 m² sec^?1 are generally much more quickly obtained, and are apparently at least as reproducible as those obtained by time-lag methods, permitting differential effects of diffusant molecular weight and shape to be studied, with solutes of higher molecular weight than those to which previous published studies were confined. Diffusion coefficients of the same solutes in a number of poly(n-alkyl 2-cyanoacrylates) were measured by desorption from polymer particles and films. The rank order and general dependence of diffusivity upon molecular weight and shape is similar in all three polymers. There is a tendency for the ionic and basic solutes to become bound, probably by covalent linkage, to poly(n-alkyl 2-cyanoacrylate) molecular chain ends.     

Stereoregularity of poly(isopropyl acrylate) and its racemization during hydrolysis

The diad tacticity of poly(isopropyl acrylate) was measured from the β-proton absorptions of poly(isopropyl acrylate-α,β-d₂) obtained with a 100 MHz NMR spectrometer, and temperature dependence of the tacticity of the polymers obtained by radical polymerization was determined. Enthalpy and entropy differences between isotactic and syndiotactic addition for poly(isopropyl acrylate) were calculated to give the following values: Δ(ΔS) = 0.7 eu; Δ(ΔH) = 0.51 kcal/mole. In the hydrolysis of poly(isopropyl acrylate-α,β-d₂), it was found that the rate of hydrolysis of poly(isopropyl acrylate) was dependent on the molecular weight rather than on the tacticity. As for the rate of racemization during hydrolysis, the rate for syndiotactic polymer was much faster than that for the isotactic polymer. The exchange reaction of deuterium at α-position with hydrogen occurred in all the polymers during hydrolysis reaction.     

The mutual diffusion coefficient for (meth)acrylate monomers as determined with a nuclear microprobe

The value of the mutual diffusion coefficient DV of two acrylic monomers is determined with nuclear microprobe measurements on a set of polymer films. These films have been prepared by allowing the monomers to diffuse into each other for a certain time and subsequently applying fast ultraviolet photo-polymerization, which freezes the concentration profile. The monomer diffusion profiles are studied with a scanning 2.1 MeV proton microprobe. Each monomer contains a marker element, e.g., Cl and Si, which are easily detected with proton induced x-ray emission. From the diffusion profiles, it is possible to determine the mutual diffusion coefficient. The mutual diffusion coefficient is dependent of concentration, which is concluded from the asymmetry in the Cl- and Si-profiles. A linear dependence of the mutual diffusion coefficient on the composition is used as a first order approximation. The best fits are obtained for a value of b=(0.38+/-0.15), which is the ratio of the diffusion coefficient of 1,3-bis(3-methacryloxypropyl)-1, 1,3,3-tetramethyldisiloxane in pure 2-chloroethyl acrylate and the diffusion coefficient of 2-chloroethyl acrylate in pure 1,3-bis(3-methacryloxypropyl)-1,1,3,3-tetramethyldisiloxane. Under the assumption of a linear dependence of the mutual diffusion coefficient DV on monomer composition, it follows that DV = (2.9+/-0.6)10(-10) m(2)/s at a 1:1 monomer ratio. With Flory-Huggins expressions for the monomer chemical potentials, one can derive approximate values for the individual monomer diffusion coefficients.     

Mechanism of diffusion and sorption of carbon dioxide in poly(vinyl acetate) above and below the glass transition temperature

The pressure dependence below 1 atm of the apparent diffusion and permeation coefficients were observed by using the permeation time lag method for carbon dioxide in poly(vinyl acetate), which has a glass transition near room temperature, at temperatures ranging from 8 to 50°C. Above the glass transition temperature, pressure dependence of the diffusion and permeation coefficient has not been observed; hence, Fick's law with a concentration independent diffusion coefficient applies. On the other hand, in the glassy state, the apparent diffusion coefficient shows pressure dependence. Moreover, the behavior of the pressure dependence does not show a clear curve in the ranges between 30°C to 17°C. Above 17°C, the apparent diffusion coefficients show discontinuities, but below 17°C increase with pressure is regular. Using the theoretical prediction of Paul, a computer was used in the numerical calculation to determine the true diffusion coefficient and other dual sorption parameters. p]The compensated diffusion coefficients controlled only by Henry's law dissolution was described by three straight lines with two intersection in the form of Arrhenius plots, which give good agreement with both our results for He and Ar and those of Meares. It is assumed that beside the dual sorption mechanism, another effect, for instance some relaxation effect may also contribute to the diffusion for carbon dioxide in poly(vinyl acetate) near the glass transition temperature region.     

Poly(methyl acrylate)/poly(hydroxyethyl acrylate) sequential interpenetrating polymer networks. Miscibility and water sorption behavior

Sequential poly(methyl acrylate)/poly(hydroxyethyl acrylate) interpenetrating polymer networks with different poly(hydroxyethyl acrylate) contents were prepared by free radical polymerization of hydroxyethyl acrylate inside the previously polymerized poly(methyl acrylate) network. Differential scanning calorimetry on dry samples shows that the interpenetrating polymer networks exhibit phase separation, and no differences are found between the glass transition temperatures of the two phases present in the interpenetrating polymer network and those of the pure components. Thermally stimulated depolarization current experiments were used to study the influence of water sorption on the mobility of the different molecular groups in the poly(hydroxyethyl acrylate) phase of the interpenetrating polymer network. Isothermal water sorption of the interpenetrating polymer networks and pure poly(methyl acrylate) and poly(hydroxyethyl acrylate) networks is analyzed with different theories to compare the behavior of the poly(hydroxyethyl acrylate) phase in the interpenetrating polymer networks with that of the pure poly(hydroxyethyl acrylate) network. Diffusion coefficients of water in the interpenetrating polymer networks are obtained by means of dynamic sorption experiments. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1587–1599, 1999     

Poly(n-butyl acrylate) based lead (II) selective electrodes

Poly(n-butyl acrylate) membranes for potentiometric ion-selective electrodes were developed and studied on example of lead-selective sensors. A novel approach resulting in Nernstian responses of tested sensor was proposed. Introduction of 5% (w/w) hydroxyethyl methacrylate into n-butyl acrylate moiety resulted in significant improvement of sensor analytical parameters. For the latter membrane material linear responses were obtained within lead activities range from 10⁻² to 10⁻⁹ mol/dm³, while for poly(n-butyl acrylate) based membranes pretreated in the same manner super-Nernstian behavior was obtained in a parallel experiment. Electrochemical impedance spectroscopy studies did not reveal significant differences between these two membranes, also similar lead ions diffusion coefficients were determined using inductively coupled plasma mass spectrometry with laser ablation.The difference between two kinds of membranes was found to concern higher Pb(II) ions contents in the surface part of the membrane with hydroxyethyl methacrylate, resulting in balanced Pb ions fluxes from/to the membrane.     

Photooxidative and pyrolytic degradation of methyl methacrylate-alkyl acrylate copolymers

Different compositions of poly(methyl methacrylate-co-methyl acrylate) (PMMAMA), poly(methyl methacrylate-co-ethyl acrylate) (PMMAEA) and poly(methyl methacrylate-co-butyl acrylate) (PMMABA) copolymers were synthesized and characterized. The photocatalytic oxidative degradation of all these copolymers were studied in presence of two different catalysts namely Degussa P-25 and combustion synthesized titania using azobis-iso-butyronitrile and benzoyl peroxide as oxidizers. Gel permeation chromatography (GPC) was used to determine the molecular weight distribution of the samples as a function of time. The GPC chromatogram indicated that the photocatalytic oxidative degradation of all these copolymers proceeds by both random and chain end scission. Continuous distribution kinetics was used to develop a model for photocatalytic oxidative degradation considering both random and specific end scission. The degradation rate coefficients were determined by fitting the experimental data with the model. The degradation rate coefficients of the copolymers decreased with increase in the percentage of alkyl acrylate in the copolymer. This indicates that the photocatalytic oxidative stability of the copolymers increased with increasing percentage of alkyl acrylate. From the degradation rate coefficients, it was observed that the photocatalytic oxidative stability follows the order PMMABA > PMMAEA > PMMAMA. The thermal degradation of the copolymers was studied by using thermogravimetric analysis (TGA). The normalized weight loss and differential fractional weight loss profiles indicated that the thermal stability of the copolymer increases with an increase in the percentage of alkyl acrylate and the thermal stability of poly(methyl methacrylate-co-alkyl acrylate)s follows the order PMMAMA > PMMAEA > PMMABA. The observed contrast in the order of photostability and thermal stability of the copolymers was attributed to different mechanisms involved for the scission of polymer chain and formation of different products in both the processes.     

A novel method for the determination of diffusion coefficients in amorphous poly(3-hydroxybutyrate)

A novel approach is proposed for the determination of the diffusion coefficient of certain drugs in amorphous poly(hydroxybutyrate) (PHB), which can be a reliable alternative to the conventional permeation based measurements. The method requires the preparation of PHB films with various concentrations of the drug and if the latter absorbs in the visible wavelength range, its concentration gradient in the polymer film as well as the time dependence of the latter can be analyzed quantitatively by following changes in color. Color can be converted into concentration with the help of adequate calibration and thus the dependence of additive concentration on space (x) and time (t), i.e. the c(x,t) function, can be determined relatively easily. The fitting of the numerical solution of Fick's second law onto the measured values provides directly the targeted diffusion coefficient. The comparison of diffusion coefficients obtained by the proposed approach to values published in the literature proved that the new method provides reliable results and requires reasonable time and effort at the same time.     

Stereoregularity of radically polymerized poly(alkyl acrylates) and poly(trimethylsilyl acrylates) and the preparation of syndiotactic poly(methyl acrylate)

Nuclear magnetic resonance (NMR) spectroscopy was used to determine the stereoregularity of radically polymerized poly(ethyl acrylates), poly(trimethylsilyl acrylates), and poly(isopropyl acrylate-α,β-d₂). The ethyl acrylate polymers consisted of a random configuration having about 50% of isotactic diads, and their stereoregularities were independent of the polymerization temperature (40 to ?78°C). Poly(trimethylsilyl acrylates) and poly(isopropyl acrylate-α,β-d₂) prepared at low temperatures had a syndiotactic configuration. Syndiotactic poly(methyl acrylate) was derived from syndiotactic poly(trimethylsilyl acrylate). For poly(methyl acrylate), an approximate estimation of the stereoregularity by infrared spectroscopy was proposed.     

Polymerization of (meth)acrylates with aluminum-based initiators

<正>A simple and effective way to prepare poly(acrylate)s,such as poly(methacrylate),poly(butyl acrylate) and poly(butyl methacrylate),has been achieved by using the single component aluminum-based compounds,such as modified methylaluminoxane(MMAO),triisobutylaluminium(TIBA) and triethylaluminium(TEA) as initiators.Effective initiations and high molecular weight polymers with unimodal molecular weight distributions could be easily obtained by varying the reaction parameters of systems under mild conditions.Although these aluminum compounds were inefficient initiators for methyl methacrylate(MMA) polymerization,they exhibited remarkable catalytic activity for butyl methacrylate(BMA) polymerization,affording high molecular weight poly(BMA)s.     

Solution properties of poly(methyl acrylate) and (1:1) poly(styrene-co-methyl acrylate)

Poly(methyl acrylate) (PMA) and 1:1 poly(styrene-co-methyl acrylate) (PSMA) were prepared by solution and bulk polymerization, respectively. The copolymer was analyzed with NMR to ascertain its composition and microstructure. The solution properties of unfractionated PMA and fractionated PSMA in ethyl acetate were investigated by light-scattering and viscosity techniques at 35°C. Narrow composition heterogeneity as revealed from the light-scattering measurements in different solvents justified the use of a single solvent for the copolymer characterization. The equations relating the limiting viscosity number to molecular weight, the molecular dimension to molecular weight, etc., were found for homopolymer and copolymers in ethyl acetate at 35°C. In the evaluation of the Flory constant K for the unperturbed state by methods based on Flory-Fox-Schaefgen, Kurata-Stockmayer, and Stockmayer-Fixman expressions, only the first method gave a value for PMA in ethyl acetate, consistent with that obtained in other solvents, whereas similar values of K were obtained by the three methods for PSMA in ethyl acetate. The studies indicate reduced thermodynamic interaction for PSMA–ethyl acetate compared to PMA–ethyl acetate, but increased steric effect in the copolymer compared with the homopolymer.     

Interpolymer complexes of poly(acrylic acid) with poly(2-hydroxyethyl acrylate) in aqueous solutions

Complexes formed from poly(acrylic acid) and poly(2-hydroxyethyl acrylate) were studied in aqueous solutions by viscometric, turbidimetric, FTIR spectroscopic, and thermogravimetric analysis methods. The formation of interpolymer complexes stabilized by hydrogen bonds was observed. It was found that the compositions of these interpolymer complexes are strongly dependent on the concentration of polymers, the order of mixing the solutions, and the pH. It was demonstrated that the complexation ability of poly(2-hydroxyethyl acrylate) is relatively low compared to other known nonionic water-soluble polymers. However, it can be significantly increased via hydrophobic modification of the poly(acrylic acid) using cetyl pyridinium bromide.     

Chemical reactions between immiscible polymers in the melt: Transesterification of poly(ethylene-co-methyl acrylate) with mono-hydroxylated polystyrenes

This article presents a unique example dealing with how chemical reactions between immiscible polymers in the melt behave differently than they would do in solution. Specifically, a model reaction was chosen: the transesterification between poly(ethylene-co-methyl acrylate) (EMA) and polystyrene mono-hydroxylated at the chain end (PSOH). It was carried out in the melt in a batch mixer. The overall rate of this reaction has a similar dependence of temperature, composition of reactants, and the nature and concentration of catalyst as in solution. The reactivity of PSOH decreases drastically with increasing molecular weight, and it becomes very weak when the molecular weight exceeds 8000 g/mol. As opposed to a reaction in solution or in a homogeneous melt, mechanical mixing increases the reaction rate since it generates interfacial area and reduces the diffusion length. The EMA-g-PS graft copolymer formed at the interfaces reduces the interfacial tension, and increases the miscibility of the reaction mixture. However, its occupation of the interfaces reduces contact between the reactive moieties, thus decreasing the overall reactivity. More importantly and much to our surprise, adding 1 to 2 wt % of an inert solvent increased greatly the overall reaction rate. While an increased interfacial mixing and diffusion by the presence of minor amounts of solvent are thought to be the major factors contributing to the drastic increase in reactivity, numerous questions still remain. Nevertheless, this study clearly showed that as opposed to a reaction in solution, mechanical mixing and the presence of minor amounts of solvent are two additional and critical means to control chemical reactions between immiscible polymer melts. © 1995 John Wiley & Sons, Inc.     

Calorimetric study of free-radical polymerized poly(p-biphenyl acrylate) and poly(p-cyclohexylphenyl acrylate)

DSC traces and specific heat data for poly(p-diphenyl acrylate) (PPBA) and poly(p-cyclohexylphenyl acrylate) (PPCPA) obtained by radical polymerization are reported. The results indicate the existence of a definite ordered phase and of a reversible firstorder solid–liquid transition in both polymers although x-ray diffraction studies showed that they are not crystalline in the conventional sense. The extent of the ordered phase present in each polymer is calculated, and the problems involved in such determination by thermal measurements are discussed. On the basis of the experimental results reported here in conjunction with the x-ray data, models are proposed for the morphology of these polymers.     

Measurements of partition,diffusion coefficients of solvents in polymer membranes using rectangular thin-channel column inverse gas chromatography (RTCCIGC)

Rectangular thin-channel columns were designed to determine partition and diffusion coefficients of small molecular weight solvents in polymer membranes based on the inverse gas chromatography (IGC) technique. The advantage of using this novel column was analyzed in terms of uniform distribution of polymer thickness, ease of preparation of stationary phase (thin polymer layer), and repeated use of the column. A mathematical model was developed to describe the velocity profile of the carrier gas, and both the time- and location-dependent concentration profiles of solvent in the column. By using the moment analysis method, the partition coefficient and diffusion coefficient were related to the dimensionless first moment and dimensionless second central moment of the elution curve of the solvent, respectively.The first dimensionless moment of the elution curve was found to be independent of the carrier gas velocity, while the second central moment increased with the increase of the carrier gas velocity. Both these behaviors support the theoretical predictions. The diffusion and partition coefficients of ethanol were obtained on polymers of cellulose diacetate (CDA) and sulfonated poly(ether ether ketone) (SPEEK) with a sulfonation degree of 79% over different temperature ranges. Based on the Arrhenius formula, the diffusion activation energies and the solvent dissolution enthalpies in both polymers were also obtained. The diffusion coefficients of 1-propanol were also obtained using two different lengths of columns.     

Preparation and Characterization of Head-to-Head Polymers. II. Head-to-Head Poly(methyl Acrylate)

Head-to-head poly(methyl acrylate) was prepared by esterification of the known alternating copolymer of ethylene and maleic anhydride. Some of the chemical,physical, and mechanical properties and the thermal degradation behavior of head-to-head poly(methyl acrylate) were studied and compared with those of head-to-tail poly(methyl acrylate). The T_g of the head-to-head polymer was higher than that of the head-to-tail polymer, but the solubilities of both types of polymers of comparable molecular weight were similar. Head-to-head poly(methyl acrylate) degraded thermally at approximately the same temperature and with a rate similar to head-to-tail poly(methyl acrylate). Unlike poly(methyl cinnamates) which cleanly degraded to monomers, poly(methyl acrylates), head-to-head and head-to-tail, degrade to very small molecules, such as CO₂, methanol, but also larger polymer fragments and char. Trace amounts of monomers (methyl acrylate) were also observed.     

Aggregation Behavior of Mono-endcapped Hydrophobically Modified Poly(sodium acrylate)s in Aqueous Solution

Titration microcalorimetry and steady-state fluorescence spectroscopy have been used to study the aggregation of mono-endcapped hydrophobically modified poly(sodium acrylate)s in aqueous solution. Polymers with molecular weights varying between 800 and 31,700 were synthesized by radical polymerization using an initiator and chain transfer agent. The resulting polymers form hydrophobic microdomains in aqueous solutions. The following conditions were applied: no salt and pH 5 and 9, respectively; 1 M sodium citrate and pH 9. At pH 5 the critical aggregation concentration (CAC, the concentration at which microdomains are formed) increases with increasing molecular weight of the polymers. The concentration range for aggregation is about 0.2-2.4 mM. At pH 9 the carboxylic acid groups are deprotonated and electrostatic repulsions are introduced; therefore the concentration for aggregation rises to about 80 mM. Interestingly, in case of polymers having M(n)<1400 the CAC decreases with increasing molecular weight due to a counterion-concentration gradient toward the hydrophobic microdomain. Near the microdomain the counterion binding is increased, reducing the electrostatic repulsions and allowing for lower aggregation concentrations. In the presence of 1 M sodium citrate this anomalous trend is suppressed to a large extent; since the overall counterion binding is increased and the CAC is lower. The concentration for aggregation is then in the same range as at pH 5 in the absence of salt. Copyright 2000 Academic Press.     

Synthesis and solution properties of star‐shaped poly(tert‐butyl acrylate)

A series of star polymers consisting of poly(tert‐butyl acrylate) arms and an ethyleneglycol dimethacrylate (EGDMA) microgel core were synthesized using anionic polymerization. The effect of various parameters (precursor length, ratio [[EGDMA]/[Initiator], reaction time, and overall concentrations) on the average number of arms was investigated. Molecular weights were determined using GPC coupled with an online viscometer and MALLS. The exponents for the relation between intrinsic viscosity or radius of gyration and molecular weight, respectively, are extremely low, indicating that the dimensions of the star polymers only slightly increase with the number of arms. After a certain number of arms is reached the intrinsic viscosity even decreases with molecular weight. Computer simulations for star polymers were carried out where the radius of gyration was calculated as a function of the number of arms. The results are in good agreement with the experimental data.     

单电子转移活性自由基聚合制备支化聚丙烯酸甲酯的研究

以丙烯酸2-(2-溴异丁酰氧基)乙酯(BIEA)为引发剂单体(inimer),丙烯酸甲酯(MA)为单体,Cu0/CuBr2和N,N,N',N″,N″-五甲基二亚乙基三胺(PMDETA)为催化体系,二甲亚砜(DMSO)为溶剂,在常温(25℃)下通过单电子转移活性自由基聚合(SET-LRP)合成支化聚丙烯酸甲酯.聚合反应过程中,采用气相色谱(GC)、核磁共振(1H-NMR)和三检测体积排除色谱(TD-SEC)等测试手段跟踪分析和表征支化聚合物的结构.研究结果表明,采用SET-LRP方法,铜粉作为催化剂,常温下聚合反应就能快速进行,130 min之内MA的转化率已达99%以上,制备出高分子量支化聚合物.随着反应的不断进行,聚合物支化程度不断提高,相比较同分子量下的线型聚合物其黏度不断下降,Mark-Houwink特征常数α最小可达0.290.此外,低分子量聚合物组分随着反应不断减少,在高单体转化率下,聚合体系中以高支化度的聚丙烯酸甲酯为主.