Assessment of defect reduction methods for nonpolar a-plane GaN grown on r-plane sapphire

This work assesses the relative effectiveness of four techniques to reduce the defect density in heteroepitaxial nonpolar a-plane GaN films grown on r-plane sapphire by metalorganic vapour phase epitaxy (MOVPE). The defect reduction techniques studied were: 3D–2D growth, SiN_x interlayers, ScN interlayers and epitaxial lateral overgrowth (ELOG). Plan-view transmission electron microscopy (TEM) showed that the GaN layer grown in a 2D fashion had a dislocation and basal-plane stacking fault (BSF) density of (1.9±0.2)×10¹¹ cm⁻² and (1.1±0.9)×10⁶ cm⁻¹, respectively. The dislocation and BSF densities were reduced by all methods compared to this 2D-grown layer (used as a seed layer for the interlayer and ELOG methods). The greatest reduction was achieved in the (0 0 0 1) wing of the ELOG sample, where the dislocation density was <1×10⁶ cm⁻² and BSF density was (2.0±0.7)×10⁴ cm⁻¹. Of the in-situ techniques, SiN_x interlayers were most effective: the interlayer with the highest surface coverage that was studied reduced the BSF density to (4.0±0.2)×10⁵ cm⁻¹ and the dislocation density was lowered by over two orders of magnitude to (3.5±0.2)×10⁸ cm⁻².     

Growth of (1 0 1¯ 3¯ ) semipolar GaN on m-plane sapphire by hydride vapor phase epitaxy

The crystalline, surface, and optical properties of the (1 0 1¯ 3¯) semipolar GaN directly grown on m-plane sapphire substrates by hydride vapor phase epitaxy (HVPE) were investigated. It was found that the increase of V/III ratio led to high quality (1 0 1¯ 3¯) oriented GaN epilayers with a morphology that may have been produced by step-flow growth and with minor evidence of anisotropic crystalline structure. After etching in the mixed acids, the inclined pyramids dominated the GaN surface with a density of 2×10⁵ cm⁻², revealing the N-polarity characteristic. In the low-temperature PL spectra, weak BSF-related emission at 3.44 eV could be observed as a shoulder of donor-bound exciton lines for the epilayer at high V/III ratio, which was indicative of obvious reduction of BSFs density. In comparison with other defect related emissions, a different quenching behavior was found for the 3.29 eV emission, characterized by the temperature-dependent PL measurement.     

Fabrication of freestanding m-plane GaN wafer by using the HVPE technique on an aluminum carbide buffer layer on an m-plane sapphire substrate

A freestanding m-plane GaN wafer is fabricated by using the hydride vapor-phase epitaxy (HVPE) technique on an aluminum carbide buffer layer on an m-plane sapphire substrate. X-ray pole-figure measurements show a clear m-plane orientation of the GaN surface. The full-width at half-maximum (FWHM) of GaN (1 1¯ 0 0) X-ray rocking curve (XRC) with the scattering vector along the [1 1 2¯ 0] direction is approximately 800 arcsec; this indicates good crystallinity. On the other hand, the FWHM for the case in which the scattering vector is oriented along the [0 0 0 1] direction is broad; this suggests the influence of structural defects along this direction. In fact, basal plane stacking faults (BSF) with a density of approximately 3×10⁵ cm⁻¹ is observed by transmission electron microscopy (TEM). The preparation of a 45-mm-diameter m-plane GaN wafer due to spontaneous separation of the GaN layer from the sapphire substrate is demonstrated.     

One-sidewall-seeded epitaxial lateral overgrowth of a-plane GaN by metalorganic vapor-phase epitaxy

The selective regrowth of GaN during sidewall-seeded epitaxial lateral overgrowth was performed. In addition to adjusting the V/III ratio, control of offset angle of the sidewall was found to be effective for realizing one-sidewall-seeded a-plane (1 1 2¯ 0) GaN on r-plane (1 1¯ 0 2) sapphire. The number of coalescence regions on the grooves was reduced, and threading-dislocation and stacking-fault densities as low as 10⁶–10⁷ cm⁻² and 10³–10⁴ cm⁻¹, respectively, were successfully realized.     

Preparation of single-crystalline ZnO films on ZnO-buffered a-plane sapphire by chemical bath deposition

High-quality zinc oxide (ZnO) films were successfully grown on ZnO-buffered a-plane sapphire (Al₂O₃ (1 1 2¯ 0)) substrates by controlling temperature for lateral growth using chemical bath deposition (CBD) at a low temperature of 60 °C. X-ray diffraction analysis and transmission electron microscopy micrographs showed that the ZnO films had a single-crystalline wurtzite structure with c-axis orientation. Rocking curves (ω-scans) of the (0 0 0 2) reflections showed a narrow peak with full width at half maximum value of 0.50° for the ZnO film. A reciprocal space map indicated that the lattice parameters of the ZnO film (a=0.3250 nm and c=0.5207 nm) were very close to those of the wurtzite-type ZnO. The ZnO film on the ZnO-buffered Al₂O₃ (1 1 2¯ 0) substrate exhibited n-type conduction, with a carrier concentration of 1.9×10¹⁹ cm⁻³ and high carrier mobility of 22.6 cm² V⁻¹ s⁻¹.     

Growth of thick GaInN on grooved (1 0 1¯ 1¯) GaN/(1 0 1¯ 2¯) 4H-SiC

We succeeded in growing high-crystalline-quality thick (1 0 1¯ 1¯) Ga_0.92In_0.08N films on a grooved (1 0 1¯ 1¯) GaN/(1 0 1¯ 2¯) 4H-SiC underlying layer. We also fabricated GaInN/GaN multiple quantum wells (MQWs) with a peak wavelength of 580 nm on a high-crystalline-quality thick GaInN film. The photoluminescence intensity of the MQWs is about six times higher than that of MQWs grown on planar GaN and twice as high as that of MQWs grown on a GaN underlying layer having the same grooved structure.     

A facile route to arsenic-doped p-type ZnO films

Undoped zinc oxide (ZnO) films have been prepared on sapphire substrates in a molecular beam epitaxy technique, and the films were annealed in air ambient along with a GaAs wafer. Arsenic in the GaAs wafer will evaporate, and enter into the ZnO films. In this facile way, arsenic-doped p-ZnO has been obtained. Hall measurements reveal that the hole concentration and Hall mobility of the ZnO:As films obtained in this way can reach 3.7×10¹⁷ cm⁻³ and 2.8 cm² V⁻¹ S⁻¹, respectively. X-ray photoelectron spectroscopy confirms the incorporation of arsenic into the ZnO films. The activation energy of the acceptors derived from temperature-dependent Hall measurement is about 164 meV.     

Electrical properties and deep traps spectra in undoped M-plane GaN films prepared by standard MOCVD and by selective lateral overgrowth

Electrical properties, deep traps spectra and structural performance were studied for m-GaN films grown on m-SiC substrates by standard metalorganic chemical vapor deposition (MOCVD) and by MOCVD with lateral overgrowth (ELO) or sidewall lateral overgrowth (SELO). Standard MOCVD m-GaN films with a very high dislocation density over 10⁹ cm⁻² are semi-insulating n-type with the Fermi level pinned near E_c−0.7 eV when grown at high V/III ratio. For lower V/III they become more highly conducting, with the electrical properties still dominated by a high density (∼10¹⁶ cm⁻³) of E_c−0.6 eV electron traps. Lateral overgrowth that reduces the dislocation density by several orders of magnitude results in a marked increase in the uncompensated shallow donor density (∼10¹⁵ cm⁻³) and a substantial decrease of the density of major electron traps at E_c−0.25 and E_c−0.6 eV (down to about 10¹⁴ cm⁻³). Possible explanations are briefly discussed.     

Development of m-plane GaN anisotropic film properties during MOVPE growth on LiAlO2 substrates

The anisotropic film properties of m-plane GaN deposited by metal organic vapour phase epitaxy (MOVPE) on LiAlO₂ substrates are investigated. To study the development of layer properties during epitaxy, the total film thickness is varied between 0.2 and 1.7 μm. A surface roughening is observed caused by the increased size of hillock-like features. Additionally, small steps which are perfectly aligned in (1 1 −2 0) planes appear for samples with a thickness of ∼0.5 μm and above. Simultaneously, the X-ray rocking curve (XRC) full width at half maximum (FWHM) values become strongly dependent on incident X-ray beam direction beyond this critical thickness. Anisotropic in-plane compressive strain is initially present and gradually relaxes mainly in the [1 1 −2 0] direction when growing thicker films. Low-temperature photoluminescence (PL) spectra are dominated by the GaN near-band-edge peak and show only weak signal related to basal plane stacking faults (BSF). The measured background electron concentration is reduced from ∼10²⁰ to ∼10¹⁹ cm⁻³ for film thicknesses of 0.2 μm and ∼1 μm while the electron mobilities rise from ∼20 to ∼130 cm²/V s. The mobilities are significantly higher in [0 0 0 1] direction which we explain by the presence of extended planar defects in the prismatic plane. Such defects are assumed to be also the cause for the observed surface steps and anisotropic XRC broadening.     

Polar dependence of impurity incorporation and yellow luminescence in GaN films grown by metal-organic chemical vapor deposition

We have investigated the unintentional impurities, oxygen and carbon, in GaN films grown on c-plane, r-plane as well as m-plane sapphire by metal-organic chemical vapor deposition. The GaN layer was analyzed by secondary ion mass spectroscopy. The different trend of the incorporation of oxygen and carbon has been explained in the polar (0 0 0 1), nonpolar (1 1 2¯ 0) and semipolar (1 1 2¯ 2) GaN by a combination of the atom bonding structure and the origin direction of the impurities. Furthermore, it has been found that there is a stronger yellow luminescence (YL) in GaN with higher concentration of carbon, suggesting that C-involved defects are originally responsible for the YL.     

Morphology and microstructure in fused silica induced by high fluence ultraviolet 3ω (355 nm) laser pulses

The morphology and microstructure induced in high quality fused silica by UV (355 nm) laser pulses at high fluence (10-45 J/cm²) have been investigated using a suite of microscopic and spectroscopic tools. The laser beam has a near-Gaussian profile with a 1/e² diameter of ∼0.98 mm at the sample plane and a pulse length FWHM (full width at half maximum) of 7.5 ns. The damage craters consist of a molten core region (thermal explosion), surrounded by a near concentric region of fractured material. The latter arises from propagation of lateral cracks induced by the laser-generated shock waves, which also compact the crater wall, ∼10 μm thick and ∼20% higher in density. The size of the damage crater varies with laser fluence, number of pulses, and laser irradiation history. In the compaction layer, there is no detectable change in the Si/O stoichiometry to within ±1.6% and no crystalline nano-particles of Si were observed. Micro- (1-10 μm) and nano- (20-200 nm) cracks are found, however. A lower valence Si³⁺ species on the top 2-3 nm of the compaction layer is evident from the Si 2p XPS. The results are used to construct a physical model of the damage crater and to gain critical insight into laser damage process.     

Electron microscopy analysis of dislocation behavior in HVPE-AlGaN layer grown on a stripe-patterned (0 0 0 1) sapphire substrate

Microstructures were investigated by transmission electron microscopy (TEM) and scanning electron microscopy (SEM) in order to clarify the dislocation behavior in AlGaN layers HVPE-grown on a stripe-patterned sapphire (0 0 0 1) substrate. SEM observation revealed very clearly the growth process: if AlGaN starting to grow from the side-wall of patterned substrate develops, a poly-crystalline region is formed up to the top surface of thin film. When the growth from the upper side (terrace) of patterned substrate is predominant, AlGaN becomes a single-crystalline layer with a flat surface. Threading dislocations (TDs) generated from the interface to the terrace propagate upwards, inclining to the wing regions. They are scarcely merged with one another. The AlGaN layer on the patterned substrate with a wider groove has a smaller density of dislocation to be about 1×10⁹ cm⁻². There are four types of dislocations: (1) TDs inclining toward 〈1 1¯ 0 0〉 normal to their Burgers vector B; (2) TDs inclining toward 〈2 1¯ 1¯ 0〉 on their slip-plane; (3) TDs inclining largely or horizontal dislocations (HDs) along 〈2 1¯ 1¯ 0〉 and (4) roundly curved HDs lying on (0 0 0 1) plane. Some TDs change the direction of inclination, suggesting that internal stress changed intricately during the growth.     

Growth of epitaxial ZnO films on Si (1 1 1) substrates with Cr compound buffer layer by plasma-assisted molecular beam epitaxy

Single crystalline ZnO film was grown on (1 1 1) Si substrate through employing an oxidized CrN buffer layer by plasma-assisted molecular beam epitaxy. Single crystalline characteristics were confirmed from in-situ reflection high energy electron diffraction, X-ray pole figure measurement, and transmission electron diffraction pattern, consistently. Epitaxial relationship between ZnO film and Si substrate is determined to be (0 0 0 1)_ZnO‖(1 1 1)_Si and [1 1 2¯ 0]_ZnO‖[0 1 1]_Si. Full-width at half-maximums (FWHMs) of (0 0 0 2) and (1 0 1¯ 1) X-ray rocking curves (XRCs) were 1.379° and 3.634°, respectively, which were significantly smaller than the FWHMs (4.532° and 32.8°, respectively) of the ZnO film grown directly on Si (1 1 1) substrate without any buffer. Total dislocation density in the top region of film was estimated to be ∼5×10⁹ cm⁻². Most of dislocations have a screw type component, which is different from the general cases of ZnO films with the major threading dislocations with an edge component.     

Investigation of nonpolar (1 1 2¯ 0) a-plane ZnO films grown under various Zn/O ratios by plasma-assisted molecular beam epitaxy

Structural and optical properties of nonpolar a-plane ZnO films grown with different II/VI ratios on r-plane sapphire substrates by plasma-assisted molecular beam epitaxy were investigated. Even by increasing the II/VI ratio across the stoichiometric flux condition a consistent surface morphology of striated stripes along the ZnO 〈0 0 0 1〉 direction without any pit formation was observed, which is contrary to polar c-plane ZnO films. Root mean square surface roughness, full width at half maximum values of X-ray rocking curves, defect densities, and photoluminescence were changed with the II/VI ratio. The sample grown with stoichiometric flux condition showed the lowest value of rms roughness, the smallest threading dislocation and stacking fault densities of ∼4.7×10⁸ cm⁻² and ∼9.5×10⁴ cm⁻¹, respectively, and the highest intensity of D^oX peak. These results imply that the stoichiometric flux growth condition is suitable to obtain superior structural and optical properties compared to other flux conditions.     

Photosensitive defects in silica layers implanted with germanium ions

Ge-implanted silica layers have been investigated by high-power pulsed synchrotron-photoluminescence (PL), photoluminescence excitation spectroscopy (PLE), and optically stimulated electron emission (OSEE) with respect to association of excitation and absorption bands to respective emission bands and lifetimes of excited defect states. In this way singlet-singlet (4.35 eV) and triplet-singlet (3.18 eV) radiative transitions from excited states of oxygen-deficient centers (ODC) in Ge-doped silica glass are characterized by their absorption and emission bands as well as their lifetimes. The main channel for non-radiative relaxation of photoexcitation is electron emission by the OSEE effect. The OSEE shows non-radiative transitions of surface and bulk E′-centers found with concentrations of (2.7-3.4) × 10¹² cm⁻² and (2-4) × 10¹⁶ cm⁻³, respectively.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Reduction of dislocations in a (1 1 2¯ 2)GaN grown by selective MOVPE on (1 1 3)Si

Two-step selective epitaxy (SAG/ELO) of (1 1 2¯ 2)GaN on (1 1 3)Si substrate is studied to reduce the defect density in the epitaxial lateral overgrowth. The first SAG/ELO is to prepare a (1 1 2¯ 2)GaN template on a (1 1 3)Si and the second SAG/ELO is to get a uniform (1 1 2¯ 2)GaN. It is found that the reduction of the defect density is improved by optimizing the mask configuration in the second SAG/ELO. The minimum dark spot density obtained is 3×10⁷/cm², which is two orders of magnitude lower than that found in a (0 0 0 1)GaN grown on (1 1 1)Si.     

High-resolution X-ray diffraction analysis on HVPE-grown thick GaN layers

The threading dislocation density of hydride vapor phase epitaxy (HVPE)-grown thick GaN layers was measured by high-resolution X-ray diffraction (HR-XRD). Three models were compared, namely mosaic model, Kaganer model and modified Kaganer model. X-ray rocking curves (XRC) of (0 0 0 2), (1 0 1¯ 5), (1 0 1¯ 4), (1 0 1¯ 3), (1 0 1¯ 2), (1 0 1¯ 1) and (1 0 1¯ 0) planes were recorded for quantitative analysis. The screw-, edge-, and mixed-type threading dislocation densities were simulated from the XRD line profile by using the three models. The dislocation density was also measured by atomic force microscopy (AFM), wet chemical etching and cathodoluminescence (CL). The results showed that the Kaganer model was more physically precise and well explained the rocking curve broadening for HVPE-grown high-quality GaN compared with the mosaic model. Assuming a randomly distributed threading dislocation configuration, we modified the Kaganer model. Based on the modified Kaganer model, the edge and screw threading dislocation densities in HVPE-grown GaN thick films ranging from 20 μm up to 700 μm were analyzed. It was shown that screw-type dislocation density decreased more rapidly than edge-type dislocation with increase in film thickness.     

FTIR, XRD and ac impedance spectroscopic study on PVA based polymer electrolyte doped with NH4X (X = Cl, Br, I)

The present study focuses on characterizing PVA: NH₄X (X = Cl, Br, I) proton conducting polymer electrolyte prepared by solution casting technique using XRD, FTIR and ac impedance spectroscopic studies. The XRD patterns of all the prepared polymer electrolytes reveal the amorphous nature of the films. The FTIR spectroscopic study indicates the detailed interaction of PVA with proton. From ac impedance spectroscopic studies, it has been found that PVA doped with NH₄I have high ionic conductivity (2.5 × 10⁻³S cm⁻¹) than PVA doped with NH₄Br (5.7 × 10⁻⁴S cm⁻¹) and NH₄Cl (1.0 × 10⁻⁵S cm⁻¹) polymer electrolytes. This is due to the large anionic size and low lattice energy of NH₄I (in comparison with NH₄Br and NH₄Cl).The temperature dependence of ionic conductivity for all the PVA: NH₄X (X = Cl, Br, I) polymer films obey Arrhenius equation. Ionic transference number measured has been found to be in the range of 0.93-0.96 for all the polymer electrolytes proving that the total conductivity is mainly due to ions.     

Properties of Ge-doped,high-quality bulk GaN crystals fabricated by hydride vapor phase epitaxy

We investigated the properties of Ge-doped, high-quality bulk GaN crystals with Ge concentrations up to 2.4×10¹⁹ cm⁻³. The Ge-doped crystals were fabricated by hydride vapor phase epitaxy with GeCl₄ as the dopant source. Cathodoluminescence imaging revealed no increase in the dislocation density at even the highest Ge concentration, with values as low as 3.4×10⁶ cm⁻². The carrier concentration, as determined by Hall measurement, was almost identical to the combined concentration of Ge and unintentionally incorporated Si. The electron mobilities were 260 and 146 cm² V⁻¹ s⁻¹ for n=3.3×10¹⁸ and 3.35×10¹⁹ cm⁻³, respectively; these values are markedly larger than those reported in the past for Ge-doped GaN thin films. The optical absorption coefficient was quite small below the band gap energy; it slightly increased with increase in Ge concentration. Thermal conductivity, estimated by the laser-flash method, was virtually independent of Ge concentration, maintaining an excellent value around 2.0 W cm⁻¹ K⁻¹. Thermal expansion coefficients along the a- and m-axes were approximately constant at 5.0×10⁻⁶ K⁻¹ in the measured doping concentration range.