Simultaneous separation of basic and acidic proteins using 1-butyl-3-methylimidazolium-based ion liquid as dynamic coating and background electrolyte in capillary electrophoresis

1-Butyl-3-methylimidazolium tetrafluoroborate ionic liquids (1B-3MI-TFB ILs) were employed as a coating material and BGE in CE for simultaneous separation of basic and acidic proteins such as lysozyme, cytochrome C, ribonuclease A, albumin, and alpha-lactalbumin. 1B-3MI-TFB ILs effectively reversed the surface charges on the capillary inner surface, preventing the adsorption of positively charged proteins onto the silica surface, as well as associated with proteins, thus benefiting the separation efficiencies and reproducibility. Consequently, simultaneous baseline separation of five proteins was achieved within 14 min by using 10 mM of 1B-3MI-TFB ILs as dynamic coating and the only running electrolyte at the voltage of +20 kV. The proposed coating technique is simple, less time-consuming, reproducible, and also stable enough for proteins separation without the need of additives. Symmetrical peaks with efficiencies up to 670,000 plates/m were obtained. Recoveries of proteins with RSD (for migration times) of 0.23-0.42% (run-to-run) and 2.5-3.8% (day-to-day) were achieved, respectively. The applicability of the proposed method in proteins separation was evaluated by the separation of egg white samples.     

Separation of acidic and basic proteins by capillary electrophoresis using gemini surfactants and gemini-capped nanoparticles as buffer additives

This paper demonstrated simultaneous separation of acidic and basic proteins using cationic gemini surfactants as buffer additives in capillary electrophoresis. We showed that even at a low concentration (0.1 mmol·L-1) of alkanediyl-α,ω-bis(dimethyloctadecylammonium bromide) (18-s-18), the wall adsorption of both acidic and basic proteins could be effectively suppressed under acidic conditions. Smaller micelle size (e.g., s=5-8) is more effective for the separation of acidic proteins than larger micelle siz...     

双子表面活性剂及其保护的纳米金作为缓冲添加剂用于毛细管电泳蛋白质分离

报道了使用阳离子双子表面活性剂作为毛细管电泳的缓冲添加剂用于同时分离酸性和碱性蛋白质.在酸性的缓冲条件下,只需要使用低浓度的阳离子双子表面活性剂（0.1mmol/L18-s-18）作为缓冲液的添加剂,就可以有效地抑制酸性和碱性蛋白质在毛细管壁的吸附,从而得到高效的蛋白质分离.实验表明,较小的胶束尺寸（如s=5～8）比大的胶束尺寸（如s〈4或〉10）能更有效地抑制酸性蛋白质的吸附.改变双子表面活性剂的中间基的长度能够对蛋白质的电泳淌度进行一定的调节,从而对分离的选择性进行一定的优化.在最优的实验条件下,蛋白质迁移时间的日内和日间标准偏差（RSD）分别小于0.8%和2.2%,回收率为79%到100.4%.另外,还考察了双子表面活性剂保护的金纳米颗粒用作毛细管电泳缓冲添加剂在蛋白质分离中的应用.实验表明,在缓冲液中加入纳米金能够缩短分析时间,并能小幅度地提高分离效率.最后,使用该方法分析了一系列复杂生物样品,包括血浆、红细胞和鸡蛋清样品,均得到了满意的结果.     

Polymeric ionic liquid as a dynamic coating additive for separation of basic proteins by capillary electrophoresis

A simple and economical capillary electrophoresis method has been developed for the analysis of four model basic proteins by employing a polymeric ionic liquid (PIL), poly(1-vinyl-3-butylimidazolium) bromide, as the dynamic coating additive. When a small amount of PIL was present in the background electrolyte, a cationic coating on the inner surface of fused-silica capillary was established. These PIL modified capillaries not only generated a stable reversed electroosmotic flow, but also effectively eliminated the wall adsorption of proteins. Several important parameters such as the PIL concentration in the background electrolyte, pH values and concentrations of the background electrolyte were optimized to improve the separation of basic proteins. Consequently, under the optimum conditions, a satisfied separation of basic proteins with peak efficiencies ranging from 247,000 to 540,000 (plates m⁻¹) had been accomplished within 11 min. The run-to-run RSDs (n = 3) of the migration times for the four basic proteins were all less than 0.37%.     

Cationic gemini surfactant as dynamic coating in CE for the control of EOF and wall adsorption

The cationic gemini surfactant ethylene bis(1-dodecyldimethylammonium) dibromide was used as a dynamic coating to control EOF and prevent wall adsorption of basic proteins in CE for the first time. This gemini surfactant shows a more powerful capability in EOF reversal than traditional single-chained surfactant. The gemini surfactant reverses the EOF at a concentration level even less than 0.01 mM, and the EOF magnitude is affected by surfactant concentration, pH, ionic strength, and ions added in buffer. Highly efficient and rapid protein separation (N > 300,000) was obtained with buffer containing 2 mM gemini surfactant under pH ranging from 3 to 6. The effects of surfactant and buffer concentration on protein separation were investigated in detail. Under the optimal conditions, good repeatability (RSD of migration time <0.6% for run-to-run and <2.5% for day-to-day assays) and recovery (>90%) of tested proteins were obtained. This new dynamic coating is also suitable for biosample analysis.     

Multilayer poly(vinyl alcohol)-adsorbed coating on poly(dimethylsiloxane) microfluidic chips for biopolymer separation

A poly(dimethylsiloxane) (PDMS) microfluidic chip surface was modified by multilayer-adsorbed and heat-immobilized poly(vinyl alcohol) (PVA) after oxygen plasma treatment. The reflection absorption infrared spectrum (RAIRS) showed that 88% hydrolyzed PVA adsorbed more strongly than 100% hydrolyzed one on the oxygen plasma-pretreated PDMS surface, and they all had little adsorption on original PDMS surface. Repeating the coating procedure three times was found to produce the most robust and effective coating. PVA coating converted the original PDMS surface from a hydrophobic one into a hydrophilic surface, and suppressed electroosmotic flow (EOF) in the range of pH 3-11. More than 1,000,000 plates/m and baseline resolution were obtained for separation of fluorescently labeled basic proteins (lysozyme, ribonuclease B). Fluorescently labeled acidic proteins (bovine serum albumin, beta-lactoglobulin) and fragments of dsDNA phiX174 RF/HaeIII were also separated satisfactorily in the three-layer 88% PVA-coated PDMS microchip. Good separation of basic proteins was obtained for about 70 consecutive runs.     

Poly-N-hydroxyethylacrylamide as a novel, adsorbed coating for protein separation by capillary electrophoresis.

We present the polymer poly-N-hydroxyethylacrylamide (PHEA) (polyDuramide) as a novel, hydrophilic, adsorbed capillary coating for electrophoretic protein analysis. Preparation of the PHEA coating requires a simple and fast (30 min) protocol that can be easily automated in capillary electrophoresis instruments. Over the pH range of 3-8.4, the PHEA coating is shown to reduce electroosmotic flow (EOF) by about 2 orders of magnitude compared to the bare silica capillary. In a systematic comparative study, the adsorbed PHEA coating exhibited minimal interactions with both acidic and basic proteins, providing efficient protein separations with excellent reproducibility on par with a covalent polyacrylamide coating. Hydrophobic interactions between proteins and a relatively hydrophobic poly-N,N-dimethylacrylamide (PDMA) adsorbed coating, on the other hand, adversely affected separation reproducibility and efficiency. Under both acidic and basic buffer conditions, the adsorbed PHEA coating produced an EOF suppression performance comparable to that of covalent polyacrylamide coating and superior to that of adsorbed PDMA coating. The protein separation performance in PHEA-coated capillaries was retained for 275 consecutive protein separation runs at pH 8.4, and for more than 800 runs at pH 4.4. The unique and novel combination of hydrophilicity and adsorptive coating ability of PHEA makes it a suitable wall coating for automated microscale analysis of proteins by capillary array systems.     

Carboxymethyl chitosan-coated capillary and its application in CE of proteins

A hydrophilic basic polysaccharide, carboxymethyl chitosan (CMC) as a capillary coating is presented with a simple preparation procedure. The CMC-coated capillary showed a long lifetime of more than 100 runs, and had good tolerance to some organic solvents, 0.1 M HCl, 0.1 M NaOH, and 5 M urea. The run-to-run, day-to-day, and capillary-to-capillary RSDs for the CMC-coated capillary were all below 2.0% for the determination of EOF. Moreover, the coatings with different concentrations and molecular weights of CMC were also investigated. The CMC-coated capillary was successfully applied to separate basic proteins and recombinant human erythropoietin (rhEPO). Furthermore, several experimental parameters, such as the concentration and pH of the running buffer, temperature, and applied voltage, were optimized for the separation of rhEPO glycoforms. Comparison of an uncoated capillary with chitosan- and CMC-coated capillaries for the separation of rhEPO glycoforms was also discussed. The results demonstrated that rhEPO glycoforms can be well separated by a CMC-coated capillary within 8 min with good reproducibility and resolution. Finally, the volatile BGE HAc-NH4Ac was utilized to separate rhEPO for its further application with CE-MS, achieving a satisfactory result.     

Weak anion and cation exchange mixed-bed microcolumn for protein separation

To separate proteins with a wide distribution of pIs under the conditions compatible to online tryptic digestion (with preferable pH=8.0), weak anion and cation exchange chromatography (WAX/WCX) mixed‐bed microcolumn has been developed. With a mixture of five proteins with pIs ranging from 4.2 to 11.4, the effect of WAX/WCX ratio on the separation performance was investigated, and an optimum packing ratio of 1:1 w/w was obtained. Moreover, the undesirable hydrophobic interaction between the proteins and the stationary phase was suppressed with 10% ACN v/v added in the mobile phases. Under the optimized conditions compatible to tryptic digestion, basic and acidic proteins were resolved simultaneously, with RSDs of relative retention time on six columns less than 6%, indicating the good resolution and packing reproducibility. Furthermore, one RPLC fraction of proteins extracted from rat middle brain and the whole protein mixture extracted from rat liver were analyzed, respectively. The results demonstrated better separation performance on WAX/WCX microcolumns than that on both weak anion exchange chromatography and weak cation exchange chromatography at pH ～8. We anticipate that WAX/WCX microcolumns are promising for the integration of protein separation and tryptic digestion aiming at high‐throughput proteome study.     

Long-chained gemini surfactants for semipermanent wall coatings in capillary electrophoresis of proteins

In this paper, we presented the first example of using gemini surfactants as semipermanent coatings in CE for protein separation. These coatings are based on the self-assembly of a series of cationic gemini surfactants, alkanediyl-alpha,omega-bis(dimethylalkylammonium bromide) (m-s-m), on the capillary wall. The coatings can keep stable for a long time without surfactant in the buffer, e.g., after the surfactants were removed from the buffer, the reversed EOF only decreased by 3.6 and 3.9% for 18-2-18 and 16-2-16 coatings over 60 min under continuous electrophoretic conditions. The coating stability increased with the alkyl chain length m. The double long chains of geminis (m > or = 14) yielded a good coating stability; meanwhile, the spacer group acted as an EOF modifier. Thus, this bifunctional surfactant coating provided a new buffer-independent method for EOF control. For 18-s-18 series, the best coating stability and largest EOF were obtained at s = 10. Ranging s from 3 to 10 yielded a linear fine-tuning of EOF and thereby allowed the adjustment of the protein apparent mobility. Highly efficient separation (>500 000 plates/m) was achieved with all the 18-s-18 coatings. Excellent run-to-run and day-to-day reproducibility (RSD of migration time 相似文献   

Capillary electrophoresis of intact basic proteins using noncovalently triple‐layer coated capillaries

The usefulness of a noncovalent, positively charged capillary coating for the efficient analysis of intact basic proteins with CE was studied. Capillaries were coated by subsequent flushing with solutions of 10% w/v Polybrene (PB), 3% w/v dextran sulfate (DS), and again 10% w/v PB. Coating characterization studies showed that stable coatings could be produced which exhibited a pH‐independent and highly reproducible EOF. The PB–DS–PB coating was evaluated with Tris phosphate BGEs of various pH using the four basic model proteins: α‐chymotrypsinogen A, ribonuclease A, cytochrome c, and lysozyme. Typical migration time RSDs for the proteins were less than 0.85%, and apparent plate numbers were above 125 000 using a capillary length of 40 cm. The high separation efficiency allowed detection of several minor impurities in the model proteins. Using a BGE of medium pH, the CE system with triple‐layer coating appeared to be useful for the repeatable profiling of recombinant humanized mouse monoclonal immunoglobulin G₁ showing a characteristic pattern of glycoforms. The CE system was also applied to the characterization of two llama antibodies, which were produced in Saccharomyces cerevisiae, revealing the presence of a side product in one of the antibodies. The high migration time stability allowed the reliable determination of antibody–antigen binding by monitoring migration time shifts. Finally, the feasibility of using the PB–DS–PB coated capillaries for CE with mass spectrometric detection was shown by the characterization of the impure llama antibody sample.     

Polyacrylamide-based monolithic capillary column with coating of cellulose tris(3,5-dimethylphenyl-carbamate) for enantiomer separation in capillary electrochromatography

A hydrophilic chiral capillary monolithic column for enantiomer separation in CEC was prepared by coating cellulose tris(3,5-dimethylphenyl-carbamate) (CDMPC) on porous hydrophilic poly(acrylamide-co-N,N'-methylene-bisacrylamide) (poly(AA-co-MBA)) monolithic matrix with confine of a fused-silica capillary. The coating conditions were optimized to obtain a stable and reproducible chiral stationary phase for CEC. The effect of organic modifier of ACN in aqueous mobile phase for the enantiomer separation by CEC was investigated, and the significant influence of ACN on the enantioresolution and electrochromatographic retention was observed. Twelve pairs of enantiomers including acidic, neutral, and basic analytes were tested and nine pairs of them were baseline-enantioresolved with acidic and basic aqueous mobile phases. A good within-column repeatability in retention time (RSD = 2.4%) and resolution (RSD = 3.2%) was obtained by consecutive injections of a neutral compound, benzoin, on a prepared chiral monolithic column, while the between-column repeatability in retention time (RSD = 6.4%) and resolution (RSD = 9.6%) was observed by column-to-column examination. The prepared monolithic stationary phase showed good stability in either acidic or basic mobile phase.     

新型共聚物涂层毛细管电泳柱及其分离蛋白质的研究

 研究新型共聚物——ＺＢ系列表面键合剂在毛细管电泳中的应用。采用物理吸附的方法制备了ＺＢ－００４,ＺＢ－０１４,ＺＢ－０１６等３种涂层毛细管柱,在ｐＨ３～５范围内,３种涂层均能有效地降低管壁对蛋白质的吸附作用和电渗流,其中亲水性较弱的ＺＢ－００４涂层的分离性能最好。在ｐＨ＜５时,涂层具有较高的稳定性和良好的分析重复性,但在更高的ｐＨ值条件下,仍然存在着峰形畸变和电渗流迅速增加的现象。     

Permanent gold nanoparticle coatings on polyelectrolyte multilayer modified capillaries for open-tubular capillary electrochromatography

This paper reports on a new strategy to coat fused silica capillaries through ionic adsorption of gold nanoparticles (AuNPs) on a polyelectrolyte multilayer (PEM) modified capillary wall. The coating was constructed in situ by alternating rinses with positively charged poly(diallydimethylammonium chloride), negatively charged poly(sodium-4-styrenesulfonate), and positively charged AuNPs. After self-assembly of n-octadecanethiol onto the surface of AuNPs, the modified capillary was investigated as a new medium for the separation of neutral analytes and proteins in open-tubular capillary electrochromatography (OT-CEC). The surface coverage of the capillary wall was increased using the high density of AuNPs which were dynamically capped with 4-dimethylaminopyridine (DMAP). The chromatographic performance of the column coated with positively charged AuNPs was remarkably improved compared with a column modified with negatively charged AuNPs. The coating was robust over more than 810 runs in this study and also showed high stability against 0.01 M NaOH, 0.01 M HCl, and electrolyte concentrations up to 70 mM. The run-to-run, day-to-day, and capillary-to-capillary reproducibilities of electroosmotic flow were satisfying with relative standard deviation values of less than 1% in all cases. The AuNP-coated PEM modified capillary column not only showed good performance for neutral analytes but also was suitable for the analysis of both basic and acidic proteins.     

Preparation and evaluation of stable coating for capillary electrophoresis using coupled chitosan as coated modifier

A coated capillary modified with a coupled chitosan (COCH) was developed by using a simple and fast (60 min) process that could be easily automated in capillary electrophoresis instrument. The COCH coating was achieved by first attaching chitosan to the capillary inner wall, and then coupling with glutaraldehyde, and rinsing chitosan again to react with glutaraldehyde. The COCH coating was stable and showed amphoteric character over the pH range of 1.8-12.0. When the pH value was lower than 4.5, the capillary surface possessed positive charges, which caused a reversal in the direction of the electroosmotic flow (EOF). The normal EOF direction could be obtained when the pH value was higher than 4.5. The COCH coating showed strong stability against 0.1 mol/L HCl, 0.1 mol/L NaOH and other solvents compared with conventional chitosan coating. The relative standard deviation of the run-to-run, day-to-day and capillary-to-capillary coating was all below 2% for the determination of EOF. The COCH-modified capillary was applied to acidic and basic proteins analyses and high efficiency could be attained. The comparison between unmodified capillary, chitosan-modified and COCH-modified capillary for the separation of real sample, extract from Elaphglossum yoshinagae with water, was also studied. Better results could be obtained on COCH-modified capillary than the other two capillaries.     

Synthesis of Hydrophilic Coating Solution for Polymer Substrate Using Glycidoxypropyltrimethoxysilane

Hydrophilic coating solutions were synthesized by adding glycidoxypropyltrimethoxysilane (GPS) to the colloidal silica suspensions adjusted to different pH. The coating solutions were coated on polyethyleneterephthalate (PET) film substrates. The pH of the colloidal silica suspensions adjusted before adding the GPS had a profound effect on chemical structure of the coating solutions and hydrophilic property of the coating films. ²⁹Si NMR spectroscopic studies showed that the solution prepared under an acidic condition (pH 4) consisted of hydrolyzed GPS monomers without siloxane bond and dimer with one siloxane bond, whereas that under a basic condition (pH 9.6) was made up larger oligomers with two or three siloxane bonds. Contact angles for water in the coating films prepared under acidic conditions exhibited smaller than those under basic conditions, indicating more hydrophilic in acidic conditions. In especial, in the case of coating films preparedunder highly acidic conditions (pH 1 and 2), the contact angles were less than 5°, which is superhydrophilic.     

New physically adsorbed polymer coating for reproducible separations of basic and acidic proteins by capillary electrophoresis

In this work, a new physically adsorbed coating for capillary electrophoresis (CE) is presented. The coating is based on a N,N-dimethylacrylamide-ethylpyrrolidine methacrylate (DMA-EPyM) copolymer synthesized in our laboratory. The capillary coating is simple and easy to obtain as only requires flushing the capillary with a polymer aqueous solution for 2 min. It is shown that by using these coated capillaries the electrostatic adsorption of a group of basic proteins onto the capillary wall is significantly reduced allowing their analysis by CE. Moreover, the DMA-EPyM coating provides reproducible separations of the basic proteins with RSD values for migration times lower than 0.75% for the same day (n = 5) and lower than 3.90% for three different days (n = 15). Interestingly, the electrical charge of the coated capillary wall can be modulated by varying the pH of the running buffer which makes possible the analysis of basic and acidic proteins in the same capillary. The usefulness of this coating is further demonstrated via the reproducible separation of whey (i.e. acidic) proteins from raw milk. The coating protocol should be compatible with both CE in microchips and CE-MS of different types of proteins.     

氧化石墨烯修饰多孔复合涂层超长开管液相色谱柱的制备与评价

采用原位聚合法在毛细管柱(3 m ×25μm i. d.)内壁制备粗糙结构的聚氯甲基苯乙烯二乙烯基苯涂层,并将氧化石墨烯以共价键合的方式固定在涂层表面,制备成氧化石墨烯修饰多孔复合涂层超长开管毛细管液相色谱柱。通过扫描电镜、透射电镜、拉曼光谱等手段对固定相的结构进行表征,证实聚氯甲基苯乙烯二乙烯基苯涂层具有球形分散结构,而片状的氧化石墨烯均匀覆盖在聚合物层表面。球状的聚合物层及氧化石墨烯的覆盖极大地提高了色谱柱的相比及样品容量,乙腈-水为流动相可分离烷基苯、中性多环芳烃、酸性和碱性化合物,乙腈-0.02 mol/ L 醋酸铵为流动相可实现4种核酸碱基样品的分离。制备的色谱柱具有良好的重复性和稳定性,测试的日内、日间、柱间重复性(n=6)相对标准偏差(RSD)均在0.3%~2.0%范围内。     

Online concentration and separation of basic proteins using a cationic polyelectrolyte in the presence of reversed electroosmotic flow

We report an online concentration and separation method for basic proteins using poly(diallyldimethylammonium chloride) (PDDA) solutions in the presence of reversed EOF. Using a capillary dynamically coated with 2% PDDA containing 0.1 M NaCl and filled with 1.2% PDDA under neutral conditions (10 mM phosphate, pH 7.0), we have demonstrated the separation of six basic proteins with peak efficiencies ranging from 175 000 to 616 000 plates/m and RSDs of migration time less than 0.4%. Additionally, high-speed separation of six basic proteins (<7 min) was achieved using a short capillary filled with 0.6% PDDA solutions. Under injection of the large-volume sample (210 nL), the LODs at S/N of 3 for basic proteins are down to nanomolar range. For example, the LOD for lysozyme is 1.2 nM, which is a 260-fold sensitivity enhancement compared with conventional injection method. The proposed method has been applied to the stacking of lysozyme in human saliva samples. Without any pretreatment, we also demonstrated the capability of this method to detect low amounts of peptide samples through the stacking of tryptic peptide of myoglobin. The experimental results indicate that our proposed method has great potential for use in clinical diagnosis and proteomics applications.     

Poly(vinylpyrrolidone)-coated silica: A versatile,polar stationary phase for HPLC

Summary Poly(vinylpyrrolidone) (PVP) is immobilized on both, small- and large-pore silicas by thermal treatment, γ-radiation, or peroxide initiated polymerization. The hydrolytic stability of such a highly polar stationary phase significantly exceeds that of a comparable phase prepared by the chemical reaction of silica with a pyrrolidone ethyl dimethylchlorosilane silanization reagent. The properties of the different PVP-silicas are evaluated by elemental analysis, spectroscopy, and chromatography. Columns of PVP-silica packings can be used in several modes: a) under normal-phase conditions as a polar bonded stationary phase, b) under reversed-phase conditions, for the separation of organic proton-donor and hydrogen-bonding compounds, c) for the aqueous size exclusion chromatography of proteins, and d) with salt gradients for the hydrophobic interaction chromatography of proteins. The minimum observable reduced plate-height of PVP-silica columns is about 3. Double-layer polymer coating experiments using PVP-silica covered with poly(methyloctadecylsiloxane) have been performed to study diffusion and shielding effects of different polymer layers in the stationary phase. Depending on separation conditions, one or the other polymer governs the retention process. A mixed selectivity was observed in a reversed phase mode with acidic eluents.