辐射加热Al等离子体的吸收谱实验

报道了辐射加热Al样品的K壳层辐射吸收谱实验. 在神光Ⅱ激光装置上，将8路主激光注入锥柱型金腔产生高温辐射源，利用该辐射源加热腔内的Al薄膜样品，产生温度达到几十电子伏的热稠密等离子体. 相对主激光延迟一定时间后，利用第9路激光短脉冲聚焦打靶加热金盘，产生短脉冲X光点光源. 通过测量075—085nm波长范围内未经样品衰减以及经过样品衰减后的背光源辐射光谱，得到了Al样品的K壳层吸收谱. 利用细致谱线计算的吸收谱对实验光谱进行拟合，确定了Al样品等离子体的电子温度.     

激光直接加热自背光法辐射不透明度测量方法探索

本文提出一种基于单束激光直接加热多层平面靶开展 稠密等离子体辐射不透明度特性研究的靶物理设计并对其进行了实验验证. 在XG-II激光装置上, 采用三倍频束匀滑激光辐照Au/CH/Al/CH多层平面靶产生背光源和Al样品等离子体, 通过观测背光源经样品等离子体衰减后的透过谱得到样品等离子体的辐射吸收性质. 采用Multi-1D程序对激光加热多层靶进行了辐射流体力学数值模拟, 给出了样品等离子体状态及其时间演化过程. 利用细致谱项模型 (DTA) 对实验测量的Al等离子体吸收谱进行理论分析, 表明等离子体温度在20–70 eV之间, 该结果与辐射流体力学模拟结果基本一致. 关键词： 吸收光谱 自背光 激光等离子体     

激光汤姆逊散射技术诊断辐射加热Fe/Al等离子体状态

在神光Ⅱ激光装置上,利用激光加热金腔产生的X射线辐射场加热Fe/Al样品,随后用激光探针光入射Fe/Al等离子体并在90°散射方向采集散射光谱,同时也记录下了样品的自发辐射光谱。实验观察到了清晰的散射光谱以及Fe等离子体自发辐射光谱,诊断结果表明,Fe/Al等离子体的平均电子温度为360eV,Fe的平均电离度为18.8。     

辐射输运实验中的Al等离子体发射光谱研究

SGII装置上用八路激光注入金腔产生高温辐射源,然后利用该辐射源来加热输运腔中的掺Al泡沫样品.从测量得到的Al类氦离子发射光谱可以观察到a—d,qr伴线的强度明显高于jkl伴线的强度,由此可以确定出光子激发和电离过程对输运腔中等离子体的形成不可忽略.除此之外,还观察到较强的互组合线发射,这表明存在一个低密度区域.最后考虑到实验测量得到的Al类氦离子发射光谱是时间、空间积分,利用两个状态等离子体的发射光谱合成再现了实验光谱. 关键词： 发射光谱 辐射加热 光谱诊断     

Ar辅助确定Al等离子体电子温度

用Ar气作保护气时 ,Nd :YAG脉冲激光烧蚀Al靶 ,将诱发Ar气电离 ,并产生丰富的Ar离子谱线辐射。文章根据Ar离子谱线辐射信息 ,分析了ArⅡ 385 0 5 7,ArⅡ 386 85 3,ArⅡ 4 0 4 2 91 ,ArⅡ 4 0 7 2 0 1nm等 4条谱线的时间分辨行为 ,计算了Al等离子体的电子温度。结果发现 :Al等离子体的电子温度约 1 5 0 0 0～2 2 0 0 0K ,随延迟时间的增加 ,电子温度单调衰减     

激光冲击波压缩稠密铝辐射不透明度实验研究

基于稠密物质辐射不透明度的理论计算目前有相当大的难度, 而稠密物质高精度不透明度数据又对聚变研究中的理论设计和模拟以及状态诊断等方面非常有用. 在"神光II"激光装置上建立一发次中能同时测量背光谱、 样品自发谱和吸收谱的大谱窗高分辨椭圆弯晶测谱系统, 并利用一维辐射流体力学程序MULTI仿真冲击波碰撞压缩样品的过程.在测量中, 用点投影背光法、激光烧蚀冲击波碰撞压缩产生稠密铝(Al)样品, 激光镱等离子体3d–4f 跃迁辐射为短脉冲背光提供样品吸收谱时空分辨诊断, 在一发次打靶中得到了背光谱、样品自发谱和X射线吸收精细结构谱, 以及稠密Al辐射吸收谱向长波偏移.实验结果给出了诊断能谱区稠密Al相对透射率分布和吸收谱偏移量. 这些工作都有益于丰富不透明度这一基础研究领域和进一步开拓许多重要应用. 关键词： 冲击波压缩等离子体 X射线吸收谱 线移 精细结构     

激光脉冲对内层等离子体辐射源的影响

本文的基本思想是设计双层金铝薄膜靶以检测激光脉冲宽度与等离子体消融深度的关系,找出有效的等离子体加热方法以产生更强更亮的等离子体辐射源.由于有预脉冲激光的存在,表层金薄膜首先被消融,由主脉冲携带的大能量就能较易穿过表层金等离子体将能量聚焦在内层铝靶上,由此产生内层高温等离子体.又由于外层低温等离子体存在,其将有效的阻碍内高温等离子体因膨胀而引起的能量损失.对无预脉冲而言,直接入射激光能量都沉积在靶表层形成表层高温等离子体.但是激光直接入射而产生的等离子体辐射总强度只比由预脉冲情况下产生的金等离子体辐射强度增加15%.而预脉冲能量只占激光总能量的2%.实验结果显示Al光谱线主要来自类氢,类氦离子跃迁.Au等离子体光谱线主要来自它的N带,O带和P带谱.我们也观察到一个明显的软X射线短波发射极限.所有结果显示由于预脉冲的存在将对靶各层等离子体辐射产生极大的影响     

再加热双脉冲激光诱导等离子体的时空演变特性研究

为了研究再加热双脉冲激光诱导击穿光谱(LIBS)对信号的增强机制,分别采用单脉冲LIBS和再加热双脉冲LIBS两种方式烧蚀合金钢样品产生等离子体,利用高分辨率的中阶梯光栅光谱仪采集等离子体发射光谱信号,同时用快速成像ICCD相机观测等离子体形态的变化,研究了两种烧蚀方式下等离子体的时空演变特性。通过比较两种烧蚀方式下等离子体产生初期光谱信号和图像的时间演变规律,发现再加热双脉冲LIBS提高了等离子体温度,且当信号采集延时等于再加热双脉冲的脉冲间隔时,等离子体温度的衰减速率发生变化;再加热双脉冲LIBS使等离子体图像强度增加,等离子体的中心区域高度和宽度分别增大了23.5%和15.1%。空间分布的研究结果表明,与单脉冲LIBS相比,当到样品表面的距离大于0.6 mm时,等离子体中的Fe Ⅱ和N Ⅰ谱线强度有较明显的增强,而Fe Ⅰ谱线在空间不同位置处的增强程度都较小,局部区域有减小的现象;再加热双脉冲LIBS使等离子体温度增加了约2 000 K,等离子体中产生了一个较大的高温区域。综合时空演变的实验结果说明再加热双脉冲对光谱信号增强的机制主要是由于第二束激光对第一束激光烧蚀样品产生的等离子体再次激发,使等离子体温度增加,进而引起等离子体辐射强度增加。     

自由定标激光诱导击穿光谱技术在炉渣成分定量分析中的应用

采用自由定标激光诱导光谱技术(CF-LIBS)对炉渣中几种主要成分(CaO,SiO2,Al2O3,MgO)进行了定量分析.利用Nd:YAG激光脉冲在空气中烧蚀炉渣样品产生等离子体,等离子体光谱由中阶梯光栅光谱仪记录.通过几种主要元素的原子谱线和离子谱线的玻尔兹曼图,计算了等离子体的温度.利用Ca的一条谱线Stark展宽...     

激光驱动的多层膜复合靶M带辐射光谱研究

时间分辨X射线吸收精细结构谱技术需要产生高亮度、均匀、宽光谱的X射线源。单一靶材产生的M带辐射源亮度高,但均匀性较差,因此提出了一种使用多种金属材料制备的多层膜复合靶产生M带辐射的方案。针对Si的K边X射线吸收谱实验,根据前期单一靶材M带光谱实验数据理论计算了最优的材料比例,制备了Au、Yb、Dy三种材料组成的多层膜复合靶,并在神光II激光装置上开展了脉冲激光驱动的多层膜复合靶辐射光谱测量,实验结果和理论计算基本一致。相比单一靶材,多层膜复合靶产生的M带辐射源具有光谱宽、整体亮度均匀的优点,在时间分辨X射线吸收精细结构谱中具有较大的应用潜力。     

辐射加热铝Ka吸收谱测量

 铝K_a吸收谱是诊断辐射加热等离子体温度的重要方法之一。在星光Ⅱ激光装置上，利用激光金膜相互作用产生的X光辐射加热其背侧的铝夹层样品，采用天津Ⅲ号胶片记录的PET晶体谱仪测量了不同激光和样品参数条件下的铝Ka吸收谱。实验观察到非常清晰的类氦到类氟铝离子Ka吸收谱线，采用细致组态模型开展了铝Ka吸收谱的模拟计算，模拟计算结果与实验结果符合得较好，研究结果可应用于辐射不透明度样品温度诊断。     

Measurement of the ionization state and electron temperature of plasma during the ablation stage of a wire-array Z pinch using absorption spectroscopy

Wire-array plasmas were investigated in the nonradiative ablation stage via x-ray absorption spectroscopy. A laser-produced Sm plasma was used to backlight Al wire arrays. The Sm spectrum was simultaneously observed by two spectrometers: one recorded the unattenuated spectrum and the other the transmission spectrum with 1.45-1.55 keV K-shell absorption lines. Analysis of absorption spectra revealed electron temperature in the range of 10-30 eV and the presence of F-, O-, N- and C-like Al ions in the absorbing plasma. A comparison of this electron temperature with the postprocessed absorption spectra of a 2D MHD simulation yields results in general agreement with the data analysis.     

中低Z材料辐射烧蚀实验研究

 在星光Ⅱ激光装置上,利用波长为0.35μm的激光注入柱腔金箔靶产生的金箔后向X光作源,烧蚀中低Z样品材料,通过空间分辨测量靶源区和样品自发辐射X光的时间过程获得了中Z铝材料的辐射烧穿时间结果;在北京同步辐射源上对透射光栅进行了实验标定。     

Iterative deconvolution of X-ray photoelectron spectra generated by an achromatic source

Three cases are presented where X-ray photoelectron spectra generated by an achromatic X-ray source have been deconvoluted by the iterative, Van Cittert method. These are (i the gold 4 f doublet, (ii) the gold valence band, and (iii) the aluminium 2 p spectrum of an oxidized aluminium foil. All prominent features in the deconvolute are shown to be real by comparison with high resolution studies, and the noise levels are low. Resolution after deconvolution is similar to that obtained with a monochromatized X-ray source. The spectra are also similar to those obtained by Fourier transform deconvolution.     

Spectroscopic diagnosis of the temperature profile of an Al:MgZ-pinch

We consider the question of how the temperature profile of a Z-pinch plasma can be determined and/or constrained by the requirement that its observed K-shell spectrum be replicated. As a case study we employ spatially integrated, time-resolved K-shell data obtained from the implosion of 30-wire Al:Mg alloy arrays on the Saturn driver at Sandia National Laboratories. Given the measured pinch size, its K-shell power and line intensities are compared with the predictions of a collisional-radiative-equilibrium plasma model whose temperature profile is varied in seeking agreement with the data. The Al data rules out a large range of possible temperature profiles, but two quite different temperature distributions can both match the measurements. These are: a uniform temperature, or, one with a sharply dropping temperature near the pinch outer edge. However, the measured ratio of the Mg α resonance lines to those of Al, even though time-integrated, excludes the possibility of a uniform temperature distribution     

Nanocylinder-array structure greatly increases the soft X-ray intensity generated from femtosecond-laser-produced plasma

In order to increase the soft X-ray conversion efficiency for the femtosecond-laser-produced plasma, we adopted a nanocylinder-array structure target. Gold nanocylinder-array targets with 70–90 nm cylinder diameter and 100 nm cylinder pitch were made. A continuous smooth soft X-ray spectrum adequate for X-ray absorption spectroscopy was obtained. An around 20-fold soft X-ray (7–20 nm) fluence enhancement compared with a flat-surface gold foil target was obtained when the cylinder height was 18 μm. X-ray (>0.06 keV) pulse duration was 17 ps, which is much shorter than that obtained by using the pre-pulse technique. The X-ray pulse peak intensity was 7-fold higher than that of a gold foil target. Received: 2 May 2001 / Revised version: 1 June 2001 / Published online: 18 July 2001     

Equation-of-state measurement of dense plasmas heated with fast protons

Using an ultrafast pulse of mega-electron-volt energy protons accelerated from a laser-irradiated foil, we have heated solid density aluminum plasmas to temperatures in excess of 15 eV. By measuring the temperature and the expansion rate of the heated Al plasma simultaneously and with picosecond time resolution we have found the predictions of the SESAME Livermore equation-of-state (LEOS) tables to be accurate to within 18%, in this dense plasma regime, where there have been few previous experimental measurements.     

Laser-produced plasma helium-like titanium Kα x-ray source and its application to Rayleighben-Taylor instability study

Several experiments are performed on the ShenGuang-II laser facility to investigate an x-ray source and test radiography concepts. X-ray lines emitted from laser-produced plasmas are the most practical means of generating these high intensity sources. By using a time-integrated space-resolved keV spectroscope and pinhole camera, potential helium-like titanium Kα x-ray backlighting (radiography) line source is studied as a function of laser wavelength, ratio of pre-pulse intensity to main pulse intensity, and laser intensity (from 7.25 to ～11.3× 10¹⁵ W/cm²⁾. One-dimensional radiography using a grid consisting of 5 μm Au wires on 16 μm period and the pinhole-assisted point projection is tested. The measurements show that the size of the helium-like titanium Kα source from a simple foil target is larger than 100 μm, and relative x-ray line emission conversion efficiency ξ_x from the incident laser light energy to helium-like titanium K-shell spectrum increases significantly with pre-pulse intensity increasing, increases rapidly with laser wavelength decreasing, and increases moderately with main laser intensity increasing. It is also found that a gold gird foils can reach an imaging resolution better than 5-μm featured with high contrast. It is further demonstrated that the pinhole-assisted point projection at such a level will be a novel two-dimensional imaging diagnostic technique for inertial confinement fusion experiments.     

X‐ray absorption spectroscopic study on gold particles formed on titania and alumina

X‐ray absorption near‐edge structure (XANES) measurements near the Au L₃ edge were made on Au(III) complex ions adsorbed on titania and alumina without a specific reducing agent. Compared with the XANES spectrum of a pure gold foil, the gold adsorbed on titania and alumina was found to be reduced to Au(0). The XANES method could obtain spectra of gold particles less than 1 nm in diameter, although a UV–visible absorption spectrum was difficult to observe with such samples. Copyright © 2003 John Wiley & Sons, Ltd.