Highly Sensitive and Selective Amperometric Detection of Periodate at Glassy Carbon Electrode Modified with a Cyclometalated Iridium(III) Complex and Single‐Wall Carbon Nanotubes

Single‐wall carbon nanotubes (SWCNTs) were used as an immobilization matrix to incorporate [Ir(ppy)₂(phen‐dione)](PF₆) complex onto a glassy carbon electrode for the study of electrocatalytic reduction of periodate ion. Detailed preliminary electrochemical data for the Ir(III)‐complex in acetonitrile solution and for the modified GCE/SWCNTs/[Ir(ppy)₂(phen‐dione)](PF₆)/CGE are presented. The modified electrode was applied to selective amperometric detection of periodate through its electrocatalytic reduction to iodide at 0.200 V and pH 2.0. The use of amperometry resulted in two calibration plots over the concentration ranges of 1‐20 μM and 20‐450 μM, with a detection limit of 0.6 μM and sensitivity of 198 nA μM^?1.     

The NADH Electrochemical Detection Performed at Carbon Nanofibers Modified Glassy Carbon Electrode

In this work, the capability of carbon nanofibers to be used for the design of catalytic electrochemical biosensors is demonstrated. The direct electrochemistry of NADH was studied at a glassy carbon electrode modified using carbon nanofibers. A decrease of the oxidation potential of NADH by more than 300 mV is observed in the case of the assembled carbon nanofiber‐glassy carbon electrode comparing with a bare glassy carbon electrode. The carbon nanofiber‐modified electrode exhibited a wide linear response range of 3×10^?5 to 2.1×10^?3 mol L^?1 with a correlation coefficient of 0.997 for the detection of NADH, a high specific sensitivity of 3637.65 (μA/M cm²), a low detection of limit (LOD=3σ) of 11 μM, and a fast response time (3 s). These results have confirmed the fact that the carbon nanofibers represent a promising material to assemble electrochemical sensors and biosensors.     

Amperometric Detection of Morphine at Preheated Glassy Carbon Electrode Modified with Multiwall Carbon Nanotubes

A highly sensitive and fast responding sensor for the determination of morphine is described. The multiwall carbon nanotubes immobilize on preheated glassy carbon electrode (5 min at 50 °C) by gently rubbing of electrode surface on a filter paper supporting the carbon nanotubes.The results indicated that carbon nanotubes(CNTs) modified glassy carbon electrode exhibited efficiently electrocatalytic oxidation for morphine with relatively high sensitivity, stability and long life. Under conditions of cyclic voltammetry, the potential for oxidation of morphine is lowered by approximately 100 mV and the current is enhanced significantly (10 times) in comparison to the bare glassy carbon electrode at wide pH range (2–9). The electrocatalytic behavior is further exploited as a sensitive detection scheme for morphine determination by hydrodynamic amperometry. Under the optimized conditions the calibration plots are linear in the concentration range 0.5–150 μM with the calculated detection limit (S/N=3) of 0.2 μM and sensitivity of 10 nA/μM and a relative standard deviation (RSD) of 2.5% (n=10). The amperometric response is extremely stable, with no loss in sensitivity over a continual 30 min operation. Such attractive ability of multiwall carbon nanotubes (MWCNTs) modified GC electrode, suggests great promise for a morphine amperometric sensor. Finally the ability of the modified electrode was evaluated for simultaneous determination of morphine and codeine.     

A Sensitive Sensor Based on Single‐walled Carbon Nanotubes: Its Preparation,Characterization and Application in the Electrochemical Determination of Drug Clorsulon in Milk Samples

Within this paper, a glassy carbon electrode modified with single‐walled carbon nanotubes (SWCNTs?GCE) was prepared, and employed for the determination of clorsulon (Clo), which is a frequently used veterinary drug against common liver fluke. The comprehensive topographical and electrochemical characterizations of bare GCE and SWCNTs?GCE were performed by atomic force microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Significantly enhanced electrochemical characteristics of SWCNTs?GCE toward a ferrocyanide/ferricyanide redox couple was observed when compared to bare GCE. Further, the prepared sensor was applied for the voltammetric determination of Clo, which was electrochemically investigated for the first time in this work. Voltammetric experiments were performed using square‐wave voltammetry with optimized parameters in phosphate buffer solution, pH 6.8, which was selected as the most suitable medium for the determination of Clo. The corresponding current at approx. +1.1 V increased linearly with Clo concentration within two linear dynamic ranges of 0.75–4.00 μmol L^?1 (R²=0.9934) and 4.00–15.00 μmol L^?1 (R²=0.9942) with a sensitivity for the first calibration range of 0.76 μA L μmol^?1, a limit of detection of 0.19 μmol L^?1, and a limit of quantification of 0.64 μmol L^?1. The developed method was subsequently applied for quantitative analysis of Clo in milk samples with results proving high repeatability and recovery.     

Sensitive Determination of Acetaminophen in the Presence of Dopamine and Pyridoxine Facilitated by their Extent of Interaction with Single‐walled Carbon Nanotubes

Single‐walled carbon nanotubes (SWCNTs) were immobilized on glassy carbon (GC) electrode by drop casting The resulting modified electrode (represented as GC/SWCNTs) efficiently oxidizes acetaminophen (AC), dopamine (DA) and pyridoxine (PY) by decreasing the respective oxidation potentials and increasing peak currents in comparison to bare GC electrode. The extent of lowering of overpotentials is in the order of AC>PY>DA, in agreement with the order of decrease in the HOMO‐LUMO energy gap (ΔE) of these analytes, as determined from Density Functional Theory (DFT) calculations. DFT calculations further reveal that due to the interaction of the analytes on the SWCNT(10,10) there is a negative charge density transfer (higher probability of electron transfer, lower ΔE value) to the frontier molecular orbitals of the analytes, which eases their oxidation. Since AC, DA and PY oxidize distinctly at distinct potential values, the present SWCNTs modified electrodes could be used to simultaneously determine them. Cyclic voltammetry, differential pulse voltammetry and amperometry techniques are utilized to understand the electrochemical characteristics of the analytes (AC, DA and PY) and subsequent sensing of them at the GC/SWCNTs electrode. The electrode is then applied to the determination of AC as a case study. Sensitivity, detection limit and linear calibration range for the AC are found to be 7.9 μA μM^?1 cm^?2, 1.1 μM and 2.0–100.0 μM, respectively. The increased electroactive surface area of the GC/SWCNTs increases the oxidation peak currents and hence increases the sensitivity of the determination.     

Electrocatalytic Oxidation of Acyclovir on Poly(p‐Aminobenzene Sulfonic Acid) Film Modified Glassy Carbon Electrode

Acyclovir is an antiviral effective drug active compound. A glassy carbon electrode (GCE) was modified with an electropolymerized film of p‐aminobenzene sulfonic acid (p‐ABSA) in phosphate buffer solution (PBS). The polymer film‐modified electrode was used to electrochemically detect acyclovir. Polymer film showed excellent electrocatalytic activity for the oxidation of acyclovir. The anodic peak potential value of the acyclovir at the poly(p‐ABSA) modified glassy carbon electrode was 950 mV obtained by DPV. A linear calibration curve for DPV analysis was constructed in the acyclovir concentration range 2×10^?7–9×10^?6 mol L^?1. Limit of detection (LOD) and limit of quantification (LOQ) were obtained as 5.57×10^?8 and 1.85×10^?7 mol L^?1 respectively. The proposed method exhibits good recovery and reproducibility.     

Electrochemical Determination of Dopamine Using a Poly(3,4-Ethylenedioxythiophene)-Reduced Graphene Oxide-Modified Glassy Carbon Electrode

Poly(3,4-ethylenedioxythiophene) was deposited on a reduced graphene oxide-decorated glassy carbon electrode through an electrochemical polymerization. The resulting glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene) electrode was applied as an electrochemical biosensor for the determination of dopamine in the presence of ascorbic acid and uric acid. The material deposited on glassy carbon electrode was investigated in terms of morphology and structural analysis. The comparison of electrochemical behavior of the glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene) electrode with the glassy carbon electrode-graphene oxide, glassy carbon electrode-reduced graphene oxide, and glassy carbon electrode-poly(3,4-ethylenedioxythiophene) electrodes exhibited high electrocatalytic activity for dopamine detection. Electrochemical kinetic parameters of glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene), including the charge transfer coefficient α (0.49) and electron transfer rate constant k_s (1.04), were determined and discussed. The glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene) electrode was studied for the determination of dopamine by differential pulse voltammetry and exhibited a linear range from 19.6 to 122.8?µM with a sensitivity of 3.27?µA?µM^?1?cm^?2 and a detection limit of 1.92?µM. The developed biosensor exhibited good selectivity toward dopamine with high reproducibility and stability.     

Electrochemical Behaviors of Baicalin at an Electrochemically Activated Glassy Carbon Electrode and Its Determination in Human Blood Serum

Electrochemical behavior of baicalin (BA) at an electrochemically activated glassy carbon electrode (GCE) had been investigated in Britton‐Robinson (B‐R) buffer solution (pH = 2.87) by cyclic voltammetry (CV) and square wave voltammetry (SWV). The experimental results suggested that the electrode exhibited an electrocatalytic activity toward the redox of BA. The electron transfer coefficient (α) and the standard rate constant (k_s) of BA at the electrochemically activated glassy carbon electrode were calculated. The reaction mechanism was proposed and discussed in this work. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of BA in the range of 5.0 × 10^?8 to 3.0 × 10^?6 mol L^?1 (r = 0.9990), with a detection limit of 2.0 × 10^?8 mol L^?1. The relative standard deviation (R.S.D.) for five times successful determination of 1.0 × 10^?6 mol L^?1 baicalin were 2.9%. The proposed method was also successfully applied for the determination of BA in human blood serum.     

A highly sensitive nonenzymatic glucose sensor based on nickel oxide–carbon nanotube hybrid nanobelts

In this study, we demonstrated a highly sensitive electrochemical sensor for the determination of glucose in alkaline aqueous solution by using nickel oxide single-walled carbon nanotube hybrid nanobelts (NiO–SWCNTs) modified glassy carbon electrode (GCE). The hybrid nanobelts were prepared by the deposition of SWCNTs onto the Ni(SO₄)_0.3(OH)_1.4 nanobelt surface, followed by heat treatment at different temperatures ranging from 400 °C to 600 °C. The NiO–SWCNTs hybrid nanobelts modified electrode prepared at 500 °C displays enhanced electrocatalytic activity towards glucose oxidation, revealing a synergistic effect between the NiO and the deposited SWCNTs. The as-fabricated nonenzymatic glucose sensor exhibits excellent glucose sensitivity (2,980 μA cm^?2 mM^?1), lower detection limit (0.056 μM, signal/noise [S/N] ratio?=?3), and wider linear range (0.5–1,300 μM). Moreover, the sensor has been successfully used for the assay of glucose in serum samples with good recovery, ranging from 96.4 % to 102.4 %.     

Determination of Methimazole on a Multiwall Carbon Nanotube Titanium Dioxide Nanoparticle Paste Electrode

A multiwall carbon nanotube titanium dioxide nanoparticle modified carbon paste electrode was used for direct determination of methimazole. The nanoparticles in the carbon paste increased the surface area of the electrode and improved the sensitivity by enhancing the peak current. The electrochemical behavior of methimazole on the modified electrode was investigated. Experimental variables such as pH and electrode composition were optimized. At the optimum pH 7.0 (universal buffer), the modified electrode had a linear dynamic range of 0.5 to 100.0 μmol L^{? 1} (0.1–11.4 ppm) with a limit of detection of 0.17 μmol L^{? 1} . The application of the electrode for the determination of methimazole in pharmaceuticals and blood serum was investigated.     

Electrocatalytic Oxidation of Formaldehyde on Copper Oxide Nano-crystalline Modified Glassy Carbon Electrode

This research found a cheap and efficient catalyst for electrooxidation of formaldehyde (HCHO). A CuO nano‐crystalline modified glassy carbon electrode (GCE) was fabricated and had an excellent electrocatalytic activity towards the oxidation of HCHO. Both the effect of potential scan rate and the effect of HCHO concentration on the electrocatalytic oxidation performance of the electrode were investigated. The amperometric current response of the electrode was proportional to HCHO concentration in the range of 1.0 µmol·L^?1–10.0 mmol·L^?1 with a detection limit (s/n=3) of 0.25 µmol·L^?1. The electrode was stable, showing the CuO nano‐crystlline is promising for applications in fuel cells and electrochemical sensors.     

Synergistic Effect of Graphene and Multiwalled Carbon Nanotubes on a Glassy Carbon Electrode for Simultaneous Determination of Uric Acid and Dopamine in the Presence of Ascorbic Acid

A poly(diallyldimethylammonium chloride)-graphene-multiwalled carbon nanotube modified glassy carbon electrode was fabricated and evaluated by cyclic voltammetry and differential pulse voltammetry. The modified electrode offered high sensitivity, selectivity, excellent long-term stability, and electrocatalytic activity for uric acid and dopamine. This sensor showed wide linear dynamic ranges of 5.0 to 350.0 µmol L^?1 for uric acid and 10.0 to 400.0 µmol L^?1 for dopamine in the presence of 500 µmol L^?1 ascorbic acid. The limits of detection were 0.13 for uric acid and 0.55 µmol L^?1 for dopamine. This functionalized electrode has potential application in bioanalysis and biomedicine.     

Chitosan Incorporating Cetyltrimethylammonium Bromide Modified Glassy Carbon Electrode for Simultaneous Determination of Ascorbic Acid and Dopamine

Simultaneous determination of a neurotransmitter, dopamine (DA), and ascorbic acid (AA) is achieved at neutral pH on a chitosan incorporating cetyltrimethylammonium bromide (CTAB) modified glassy carbon (GC) electrode. Differential pulse voltammetry (DPV) technique was used to investigate the electrochemical response of DA and AA at a glassy carbon electrode modified with chitosan incorporating CTAB. An optimum 6.0 mmol L^?1 of CTAB together with 0.5 wt% of chitosan was used to improve the resolution and the determination sensitivity. In 0.1 mol L^?1 aqueous phosphate buffer solution of pH 6.8, the chitosan‐CTAB modified electrode showed a good electrocatalytic response towards DA and AA. The anodic peak potential of DA shifted positively, while that of AA shifted negatively. Thus, the difference of the anodic peaks of DA and AA reached 0.23 V, which was enough to separate the two anodic peaks very well. The presented method herein could be applied to the direct simultaneous determination of DA and AA without prior treatment. The anodic peak currents (I_pa) of DPV are proportional to DA in the concentration range of 8 μM to 1000 μM, to that of AA 10 μM to 2000 μM, with correlation coefficients of 0.9930 and 0.9945, respectively. The linear range is much wider than previously reported.     

Anodic Stripping Voltammetric Determination of Mercury(II) in Water Using a 4‐Tert‐Butyl‐1‐(Ethoxycarbonylmethoxy)Thiacalix[4]Arene Modified Glassy Carbon Electrode

A glassy carbon electrode coated the film of 4‐tert‐butyl‐1‐(ethoxycarbonylmethoxy)thiacalix[4]arene is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode, the modified electrode can improve the measuring sensitivity of Hg²⁺. Under the optimum experimental condition, the modified electrode in 0.1 mol L^?1 H₂SO₄ + 0.01 mol L^?1 KCl solution shows a linear voltammetric response in the range of 8.0 × 10^?9 ～ 3.0 × 10^?6 mol L^?1 with detection limit 5.0 × 10^?9 mol L^?1 for Hg²⁺. The high sensitivity, selectivity, and stability of modified electrode also prove its practical application for a simple, rapid and economical determination of Hg²⁺ in water samples.     

Poly(Taurine‐Glutathione)/Carbon Nanotube Modified Glassy Carbon Electrode as a New Levofloxacin Sensor

A new highly sensitive and selective electrochemical levofloxacin sensor based on co‐polymer‐carbon nanotube composite electrode was developed. Taurine and Glutathione were electrochemically co‐polymerized on multiwalled carbon nanotubes modified glassy carbon electrode (Poly(TAU‐GSH)/CNT/GCE) and used as a levofloxacin sensor in pH 6 phosphate buffer solution. The new composite electrode surfaces were characterized by scanning electron microscopy, atomic force microscopy and electrochemical impedance spectroscopy. Under the optimized conditions, two linear segments were obtained for increasing LEV concentrations between 20 nmol L^?1‐1 μmol L^?1 and 1.5 μmol L^?1‐55 μmol L^?1 LEV with a detection limit of 9 nmol L^?1 using amperometry. Poly(TAU‐GSH)/CNT/GCE exhibited high sensitivity, selectivity with good stability. The new sensor was employed for real samples of LEV tablets and urine. Promising results were obtained with good accuracy which were also in accordance with LC‐MS/MS analysis.     

Synthesis of magnetic molecularly imprinted polymer particles for selective adsorption and separation of dibenzothiophene

We are presenting an electrochemical sensor for the simultaneous determination of dopamine (DA) and uric acid (UA) in the presence of even high concentrations of ascorbic acid (AA). It based on a glassy carbon electrode modified with an electroactive film of polymerized dibromofluorescein. The electrochemical behaviors of DA and UA were studied by cyclic voltammetry using the modified electrode. It exhibits excellent electrocatalytic activity towards the oxidation of the two analytes. Most notably, the oxidation potentials differ by 180 and 200?mV between AA-DA and DA-UA, respectively. Thus, excellent selectivity towards the oxidation of DA and UA in the presence of even high concentrations of AA is accomplished. Under the optimum conditions, the anodic peak currents are linearly related to the concentrations of DA and UA in the range from 0.2 to 200?μmol?L^-1 and from 1.0 to 250?μmol?L^-1, respectively. The detection limits for DA and UA are 0.03?μmol?L^-1 and 0.2?μmol?L^-1, respectively (at an S/N of 3). The method has good selectivity and sensitivity and was successfully applied to the simultaneous determination of DA and UA in spiked human serum.

Electrochemical Behavior of 8‐Azaguanine at DNA Langmuir–Blodgett Modified Glassy Carbon Electrode and Its Analytical Application

A highly sensitive electrochemical biosensor for the detection of trace amounts of 8‐azaguanine has been designed. Double stranded (ds)DNA molecules are immobilized onto a glassy carbon electrode surface with Langmuir–Blodgett technique. The adsorptive voltammetric behaviors of 8‐azaguanine at DNA‐modified electrode were explored by means of cyclic voltammetry and square wave voltammetry. Compared with bare glassy carbon electrode (GCE), the Langmuir–Blodgett film modified electrode can greatly improve the measuring sensitivity of 8‐azaguanine. Under the optimum experimental conditions, the Langmuir–Blodgett film modified electrode in pH 3.0 Britton–Robinson buffer solutions shows a linear voltammetric response in the range of 5.0×10^?8 to 1.0×10^?5 mol L^?1 with detection limit 9.0×10^?9 mol L^?1. The method proposed was applied successfully for the determination of 8‐azaguanine in diluted human urine with wonderful satisfactory.     

Electrochemical Behavior and Determination of L‐Tyrosine at Single‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

Based on single‐walled carbon nanotubes (SWCNTs) modified glassy carbon electrode (GCE/SWCNTs), a novel method was presented for the determination of L ‐tyrosine. The GCE/SWCNTs exhibited remarkable catalytic and enhanced effects on the oxidation of L ‐tyrosine. In 0.10 mol/L citric acid‐sodium citrate buffer solution, the oxidation potential of L ‐tyrosine shifted negatively from +1.23 V at bare GCE to +0.76 V at GCE/SWCNTs. Under the optimized experimental conditions, the linear range of the modified electrode to the concentration of L ‐tyrosine was 5.0×10^?6–2.0×10^?5 mol/L (R₁=0.9952) and 2.7×10^?5–2.6×10^?4 mol/L (R₂=0.9998) with a detection limit of 9.3×10^?8 mol/L. The kinetic parameters such as α (charge transfer coefficient) and D (diffusion coefficient) were evaluated to be 0.66, 9.82×10^?5 cm² s^?1, respectively. And the electrochemical mechanism of L ‐tyrosine was also discussed.     

Electrochemical Detection of NADH,Cysteine, or Glutathione Using a Caffeic Acid Modified Glassy Carbon Electrode

A modified electrode was prepared using electrodeposition methods to immobilize caffeic acid (CAF) onto the surface of a glassy carbon electrode (GCE) to create a polymer suitable for biosensor development. The polymer film coverage of the surface bound species was further optimized using electrodeposition methods, thus increasing the surface coverage to ca. 10^?9 mol cm^?2. Using cyclic voltammetry, the modified carbon electrode was used to facilitate and observe the electrocatalytic oxidation of coenzymes such as NADH, cysteine, and glutathione at different concentrations. A calibration curve was determined in each case within the concentration range; 300 nM to 10 mM, with the limits of detection (LOD) of 246 µM, 99 µM, 2.2 µM for NADH, cysteine, and glutathione respectively.     

Electrochemical Detection of Persulfate at the Modified Glassy Carbon Electrode with Nanocomposite Containing Nano‐Ruthenium Oxide/Thionine and Nano‐Ruthenium Oxide/Celestine Blue

The present study describes the fabrication of a sensitive amperometric sensor for the determination of persulfate. The immobilization surface was prepared by modifying a glassy carbon (GC) electrode with a nanocomposite containing ruthenium oxide (RuOx) nanoparticles and thionine (TH) or celestin blue (CB). The modified electrodes indicated excellent electrocatalytic activity toward persulfate reduction at a potential of +0.1 V. The proposed sensor showed detection limits of 1.46 µM for the GC/RuOx/TH modified electrode and 2.64 µM for the GC/RuOx/CB modified electrode. The sensitivities were obtained as 3 nA µM^?1 at a concentration range of 10 µM to 11 mM for the GC/RuOx/TH modified electrode and 1 nA µM^?1 at a concentration range of 10 µM to 6 mM for the GC/RuOx/CB modified electrodes.