Surface‐Confined Electropolymerization of Methylene Blue on Gold Electrodes

We report on the electrochemical behaviour and electropolymerization of self‐assembled monolayers (SAMs) of methylene blue (MB) on gold electrodes. The SAMs of MB on gold electrodes were prepared by immersing the substrates into a solution of 1.0 mM MB in absolute ethanol for different times at room temperature. Cyclic voltammetry experiments exhibited that reductive desorption of MB monolayer takes place at three different potentials on polycrystalline gold electrodes, while reductive desorption of MB monolayer consists of only one peak on single crystal Au(111) substrates. Calculated charge densities for different immersion times indicated that optimal immersion time for self‐assembly of MB is 96 h. Electropolymerization of SAMs of MB on gold electrode was achieved by applying 0.95 V for 1 s in 0.1 M borate buffer solution (pH: 9.0). It was observed that poly(MB) monolayers are highly stable in acidic media. ATR‐FTIR and UV‐vis spectra exhibited differences between monomer and polymer monolayers, which are attributed to surface‐confined electropolymerization. STM image of poly(MB) monolayer on Au(111) substrate revealed a surface that is covered by well‐ordered, collateral nanowires with an average size of 3 nm.     

Lightweight ITO Electrodes Decorated with Gold Nanostructures for Electrochemical Applications

Gold nanostructures were fabricated on a transparent indium tin oxide (ITO) coated PET substrate by an electrodeposition technique from a potassium gold (III) chloride solution for two different types of applications. It was found that the optical transparency of lightweight ITO electrodes could be maintained by depositing isolated gold nanostructures while opening up the use of these electrodes for inner sphere electron reactions, such as hydroquinone oxidation, which are not possible at ITO electrodes. For practical applications the adhesion of gold to the ITO electrode was improved by modifying the ITO surface with 3‐mercaptopropyl‐trimethoxysilane (MPS). Compared to Au/ITO, the Au/MPS/ITO electrode showed vastly improved electrochemical activity toward various electron transfer reactions when subjected to mechanical stress. The biosensing properties of the Au/MPS/ITO electrode was also investigated by studying the detection of immobilized DNA on the Au/MPS/ITO electrode via electrochemical impedance spectroscopy (EIS).     

Microwave synthesis of electrically conductive gold nanowires on DNA scaffolds

Biological molecules, in particular DNA, have shown great potential to be used as interconnects of nanodevices and computational elements. In this research, we synthesized electrically conductive gold nanowires for the first time exploiting an electroless and microwave heating method for 120-180 s. Our results indicate that DNA serves as a reducing and nonspecific capping agent for the growth of nanowires. The current voltage ( I- V) characteristics of the Au nanowires are continuous, exhibiting Ohmic behavior having low contact resistance with the gold electrodes. The nanowires have a diameter of 10-15 nm in solution and of 20-30 nm in immobilized DNA with resistivity comparable to pure metals. The method is highly selective with deposition confined to the DNA itself. The nanowires we fabricated can be used as building blocks for functional nanodevices, sensors, and optoelectronics.     

Temperature dependence of the field effect mobility of solution-grown germanium nanowires

The temperature dependence of the field effect mobility was measured for solution-grown single-crystal Ge nanowires. The nanowires were synthesized in hexane from diphenylgermane by the supercritical fluid-liquid-solid process using gold nanocrystals as seeds. The nanowires were chemically treated with isoprene to passivate their surfaces. The electrical properties of individual nanowires were then measured by depositing them on a Si substrate, followed by electrical connection with Pt wires using focused ion beam assisted chemical vapor deposition. The nanowires were positioned over TaN or Au electrodes covered with ZrO2 dielectric that were used as gates to apply external potentials to modulate the conductance. Negative gate potentials increased the Ge nanowire conductance, characteristic of a p-type semiconductor. The temperature-dependent source/drain current-voltage measurements under applied gate potential revealed that the field effect mobility increased with increasing temperature, indicating that the carrier mobility through the nanowire is probably dominated either by a hopping mechanism or by trapped charges in fast surface states.     

Preparation and electrical properties of ultrafine Ga2O3 nanowires

Uniform and well-crystallized beta-Ga2O3 nanowires are prepared by reacting metal Ga with water vapor based on the vapor-liquid-solid (VLS) mechanism. Electron microscopy studies show that the nanowires have diameters ranging from 10 to 40 nm and lengths up to tens of micrometers. The contact properties of individual Ga2O3 nanowires with Pt or Au/Ti electrodes are studied, respectively, finding that Pt can form Schottky-barrier junctions and Au/Ti is advantageous to fabricate ohmic contacts with individual Ga2O3 nanowires. In ambient air, the conductivity of the Ga2O3 nanowires is about 1 (Omega.m)-1, while with adsorption of NH3 (or NO2) molecules, the conductivity can increase (or decrease) dramatically at room temperature. The as-grown Ga2O3 nanowires have the properties of an n-type semiconductor.     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

Magnetically Assembled Multisegmented Nanowires and Their Applications

Here we report a cost effective and versatile way of synthesizing and assembling multi‐functional (e.g., gold‐polypyrrole‐nickel‐gold) nanowires. Multisegmented nanowires were synthesized using electrodeposition method for precise control over segment dimensions for proper expression of material functionality. The nanowires were integrated on microfabricated electrodes using magnetic dipole interactions between the ferromagnetic segment in the nanowire and the ferromagnetic electrodes. The electrical properties of multisegmented nanowires showed semiconducting behavior with the activation energy of ca. 0.27 eV for the conducting polymer segment of the nanowire. These nanowire devices showed response towards light and exposure to ammonia, demonstrating their potential use as photonic device and gas sensor, respectively.     

Ultrathin Au nanowires and their transport properties

This paper presents a facile synthesis of single-crystalline Au nanowires by reduction of HAuCl4 in oleic acid and oleylamine. The diameter of these micron-meter-long Au nanowires is controlled to be 3 and 9 nm by volume ratio of oleylamine and oleic acid. When linked between two gold electrodes, the 9 nm Au nanowire shows good electron conductivity with its breakdown current density reaching 3.5 x 10(12) A/m2. This demonstrates that the chemically made ultrathin Au nanowires can be used as a molecular-scale interconnect for nanoelectronic applications.     

Physical vapor deposition of one-dimensional nanoparticle arrays on graphite: seeding the electrodeposition of gold nanowires

One-dimensional (1D) ensembles of 2-15 nm diameter gold nanoparticles were prepared using physical vapor deposition (PVD) on highly oriented pyrolytic graphite (HOPG) basal plane surfaces. These 1D Au nanoparticle ensembles (NPEs) were prepared by depositing gold (0.2-0.6 nm/s) at an equivalent thickness of 3-4 nm onto HOPG surfaces at 670-690 K. Under these conditions, vapor-deposited gold nucleated selectively at the linear step edge defects present on these HOPG surfaces with virtually no nucleation of gold particles on terraces. The number density of 2-15 nm diameter gold particles at step edges was 30-40 microm-1. These 1D NPEs were up to a millimeter in length and organized into parallel arrays on the HOPG surface, following the organization of step edges. Surprisingly, the deposition of more gold by PVD did not lead to the formation of continuous gold nanowires at step edges under the range of sample temperature or deposition flux we have investigated. Instead, these 1D Au NPEs were used as nucleation templates for the preparation by electrodeposition of gold nanowires. The electrodeposition of gold occurred selectively on PVD gold nanoparticles over the potential range from 700-640 mV vs SCE, and after optimization of the electrodeposition parameters continuous gold nanowires as small as 80-90 nm in diameter and several micrometers in length were obtained.     

偶氮吡啶分子结的制备、表征及电学性质初步研究

具有特异电学性质的分子结的制备及电子输运特性研究是分子电子学领域中的主要内容,对构筑分子电子器件具有重要意义．但是,由于分子结的尺度通常在100nm以下,这使得分子结的低缺陷制备和准确有效的电学特性研究面临困难．目前,自组装方法已经成为降低分子结缺陷的主要手段,     

A Highly Sensitive and Selective Multiwall Carbon Nanotubes/Nafion/Au Microarrays Electrode for Dopamine Determination

This work presents the fabrication of Nafion (Nf) or Nafion/Multiwalled Carbon Nanotubes (Nf/MWCNTs) modified gold microarray (Au‐µA) and macro‐(Au‐M)electrode biosensors. The surface morphologies of the above electrodes were examined using SEM. The catalytic properties of the above electrodes towards dopamine were tested using square wave voltammetric technique. The Nf/MWCNT/Au‐µA electrode exhibited a wide range (0.1–1000 nM) of linearity among the other electrodes. The LOD of Nf/MWCNT/Au‐µA electrode was 50 pM for dopamine in the presence of 5000 µM ascorbic acid. Therefore, the Nf/MWCNT/Au‐µA biosensor was applied for the determination of dopamine in human serum.     

A Flexible Nafion Coated Enzyme‐free Glucose Sensor Based on Au‐dimpled Ti Structures

The detection of glucose at low concentrations using electrochemical sensors is of great importance due to the possibility of using different human body fluids than blood, such as e. g. urine, saliva, sweat or tears. The interest behind those biofluids is related to their utility in non‐invasive sugar determination. In this work, we present flexible, fully biocompatible electrode material based on Au nanoparticles immobilized onto titanium dimples. Au?Ti heterostructures were obtained via electrochemical anodization of titanium foil in presence of fluoride anions followed by chemical etching, magnetron sputtering of gold and subsequent thermal dewetting in continuous regime. In the last step of fabrication, electrodes were modified by permselective Nafion membrane. The selection of the best electrode material among different configurations was carried out basing on the electrochemical activity in the contact with 5 mM glucose dissolved in neutral air‐saturated 0.1 M PBS. For the 10 nm Au dewetted gold film, limit of detection of 30 μM and high sensitivity of 93 mA cm^?2 mM^?1 were achieved. Application of Nafion membrane caused complete inhibition of the impact of various interference species onto the glucose detection. Good selectivity and repeatability combined with the resistance to prolonged mechanical stress suggest that prepared material can be used in non‐invasive glucose sensing.     

Prussian Blue Modified Submicron Structured Gold Electrodes for Amperometric Hydrogen Peroxide Sensing

In this work, we present a simple and effective approach for fabricating sub‐micron structured gold (SM−Au) electrodes by chemically etching the magnetron co‐sputtered gold film in KI solution for certain time. Such electrodes with a large surface area to volume ratio were used as the matrix for electrochemical deposition of Prussian blue (PB) to develop an electrochemical hydrogen peroxide sensor. Experimental characterization using scanning electron microscope and atomic force microscope shows that the thickness of PB layer on SM−Au electrode is around 140 nm, and is composited with cubic PB nanocrystals. The electrochemical performance of the designed sensor, studied using cyclic voltammograms and chronoamperometry methods, suggests that the sensor based on SM−Au/PB electrode presents the direct electron transfer of PB particle towards SM−Au film, and exhibits fast response, wide linearity, low detection limit and high stability. Under the optimized conditions, the sensitivity of the developed sensor for the detection of H₂O₂ reaches the value of 512 mA cm⁻² M⁻¹ with a linear range from 1 μM to 4.5 mM.     

Observation and Identification of an Atomic Oxygen Structure on Catalytic Gold Nanoparticles

Interactions between oxygen and gold surfaces are fundamentally important in diverse areas of science and technology. In this work, an oxygen dimer structure was observed and identified on gold nanoparticles in catalytic decomposition of hydrogen peroxide to oxygen and water. This structure, which is different from isolated atomic or molecular oxygen surface structures, was observed with in situ surface‐enhanced Raman spectroscopic measurements and identified with density functional theory calculations. The experimental measurements were performed using monodisperse 5, 50 and 400 nm gold particles supported on silica with liquid‐phase hydrogen and deuterium peroxides at multiple pH values. The calculations show that on surfaces with coordinatively unsaturated gold atoms, two oxygen atoms preferentially share a gold atom with a bond distance of 0.194–0.196 nm and additionally bind to two other surface gold atoms with a larger bond distance of 0.203–0.213 nm, forming an Au‐O‐Au‐O‐Au structure. The formation of this structure depends on reaction rates and conditions.     

Geometric Effects on Conductance in Single Molecule Electron Transport Junctions

We studied electron transport properties of a dithiol‐benzene molecule covalently bonded between two gold electrodes by combining ab initio calculations for the central molecule and a green function method to calculate electron transport. Due to the large computational demand, this type of calculations usually involves certain ways of simplification. The simplification commonly used is to fix the contact surface of the electrodes by ignoring the disturbance of the Au contact surface by contacting with the central molecule, i.e. without scattering region relaxation. In this study, we intended to resolve the difference between models with and without the above simplification. The large conductance found in our models without scattering region relaxation is due to the highly symmetric arrangement of the Au contact surface and those layers near the contact. The disturbance of the Au contact surface by the contact of the central molecule is important since the increase of the Au‐S bond and the distortion of the Au atom on the FCC site can lower the transmission coefficient between the two electrodes. In order to obtain better results, the model should include scattering region relaxation. However, when such relaxation is not applicable or demands too much calculation resource, the center molecule of the electronic transport junction should be at least optimized by the calculation level including electronic correlation, i.e. post‐HF methods.     

Immobilization of Prussian blue nanoparticles onto thiol SAM modified Au electrodes for analysis of DL-homocysteine

Prussian blue (PB) nanoparticles were immobilized onto gold electrodes using L-cysteine, 1,3-propanedithiol, and 1,8-octanedithiol as a bridge between the gold surface and the PB nanoparticles by the self-assembly method. The obtained PB/thiol/Au electrodes exhibit direct and indirect electrocatalytic activity toward DL-homocysteine (HCys) oxidation. It is possible for these PB nanoparticles modified electrodes to be used for the determination of HCys. The text was submitted by the authors in English.     

Voltammetric Study of Methylene Blue at Thiol SAMs‐Modified Gold Electrodes

The voltammetric behavior of methylene blue (MB) at thiol self‐assembled monolayers modified gold electrodes (SAMs/Au) has been investigated. MB exhibited a redox peak at about ?0.35 V (vs.SCE) in alkaline solution at bare gold electrodes. When the gold electrodes were modified with thiol SAMs, the peak grew due to the accumulation of MB at SAMs. With the solution pH rising, more MB was accumulated, hence the peak height increased, which differed from that at bare gold electrodes. The electrode process at SAMs/Au featured the characteristics of adsorption and/or electrode reaction controlled. The enhancing action of glutathione monolayer (GSH SAM), 3‐mercaptopropionic acid monolayer (3MPA SAM) and other thiol SAMs was compared. Among these, GSH SAM made the MB peak increase more. At GSH SAM/Au, the peak height varied linearly with MB concentration over the range of 2 μM to 400 μM. So this can be developed for the determination of MB and studies concerned. The accumulation behavior caused by GSH SAM and native fish sperm dsDNA was compared. The interaction between DNA and MB was also discussed under this condition.     

Au nanolayers deposited on polyethyleneterephtalate and polytetrafluorethylene degraded by plasma discharge

Polyethyleneterephtalate (PET) and polytetrafluorethylene (PTFE) foils were modified by plasma discharge. The effect of plasma modification on polymer surface wettability and on properties of gold coatings were studied as a function of time from plasma exposure (aging time) and polymer substrate temperature. Thickness, sheet resistance, and surface topology of gold layers were studied. Aging of the plasma‐exposed samples is accompanied by increase in contact angle, which is explained by rearrangement of the polymer segments in the polymer surface monolayer, and a decrease in the concentration of polar groups. The aging also leads to a decline in surface roughness R_a measured by atomic force microscopy (AFM). Under deposition conditions, comparable thicknesses of deposited Au layers were prepared on pristine PET and plasma‐treated PET and PTFE samples. The thinnest Au layers were evaporated onto pristine PTFE. The sheet resistance decreases with increasing thickness of Au layer. Plasma treatment leads to an increase of PTFE surface roughness, which becomes even more pronounced after Au deposition. A higher roughness shows that the PET samples are deposited with the Au layer at temperatures above the glassy transition temperature T_g. Copyright © 2006 John Wiley & Sons, Ltd.     

Electrosorption of hydrogen into palladium-gold alloys

Hydrogen electrosorption into Pd-Au alloys has been studied in acidic solutions (1 M H₂SO₄) using cyclic voltammetry. Pd-Au electrodes with limited volume were prepared by electrochemical co-deposition. It was found that the maximum H/(Pd+Au) ratios decrease monotonically with increasing gold content and reach zero at ca. 70 at% Au. Similarly to the case of Pd limited volume electrodes, two peaks in the hydrogen region, corresponding to two types of sorbed hydrogen, are observed on voltammograms for Pd-rich alloys. The hydrogen capacity, H/(Pd+Au), measured electrochemically, depends on the sweep rate in the cyclic voltammetry experiments, which suggests that two different mechanisms for hydrogen desorption from the Pd-Au alloy are possible. After a strong decrease of Pd concentration at the electrode surface, caused by long cyclic polarization to sufficiently anodic potentials, the amount of absorbed hydrogen is still significant for alloys initially rich in Pd. The results obtained from CO adsorption experiments suggest that only Pd atoms are active in the hydrogen absorption/desorption process. Electronic Publication     

Controllable growth of gold nanowires and nanoactuators via high-frequency AC electrodeposition

An electrochemical deposition method using high-frequency alternating current (AC) signal is reported here for the in situ synthesis and assembly of Au nanowires and nanoactuators on microelectrodes without using any masks or templates. High conductivity of 3.79 ± 0.14 × 10⁷ Ω^− 1 m^− 1 is achieved on the Au nanowires assembled between electrodes. Au nanoactuators with expansion ratio of more than 500% can be fabricated at higher frequency. The actuators can act as claws to grab SiO₂ nanoparticles in a water solution when driven by an alternating electric field. Disconnected nanowires and nanoparticles which self-aligned around the electrodes were also obtained at lower gold ion concentration, indicating a different current transfer mode in AC electrodeposition.