以混合表面活性剂为模板可控合成MCM-48和MCM-41分子筛

利用阳离子和三嵌段共聚物混合表面活性剂为模板,在水热条件、碱性介质中可控合成出MCM-48和MCM-41分子筛。在固定P123(聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物):TEOS(正硅酸乙酯)(物质的量的比)为0.01875的体系中,调节CTAB(十六烷基三甲基溴化铵)∶TEOS(正硅酸乙酯)物质的量比值m,当m在0.12~0.13范围合成出MCM-48分子筛;当m在0.04~0.08范围合成出MCM-41分子筛。通过XRD,TEM,N2物理吸附,IR等方法进行了表征。结果表明:聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物(P123)的加入可以更大程度地降低合成介孔材料所需阳离子表面活性剂的用量;可控合成的介孔材料具有高比表面积、高度有序的孔道结构、较集中的孔径分布。     

以混合阳离子-嵌段共聚物表面活性剂为模板合成介孔MCM-48

利用阳离子和嵌段共聚物混合表面活性剂为模板,在水热条件、碱性介质中成功地合成出MCM-48介孔分子筛。在1TEOS(正硅酸乙酯)∶0.125CTAB(十六烷基三甲基溴化铵)∶nP123(聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物)∶0.50NaOH(氢氧化钠)∶61H₂O(物质的量的比)体系中,n值在较大范围内(0.000 625～0.018 75)可调。通过粉末X射线衍射(XRD)、N₂物理吸附、扫描电镜(SEM)对合成样品进行表征。结果表明：聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物(P123)的加入可以更大程度地降低合成MCM-48所需阳离子表面活性剂的用量;合成的MCM-48具有高比表面积、高度有序的孔道结构、较集中的孔径分布和较高的热和水热稳定性。     

乙烷桥键介孔材料的制备及其在反相液相色谱中的应用

以1,2-二(三甲氧基硅基)-乙烷为硅源、聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物(EO20PO70EO20,P123)为模板剂、十六烷基三甲基溴化铵(CTAB)为共模板剂、乙醇为共溶剂,在酸性条件下合成了一种乙烷桥键有序介孔材料(PME)。研究表明,该PME具有高的比表面积(1152 m2/g)、高度有序的孔结构(二维六方相)、窄的孔径分布及表面光滑的球形形貌。将该PME不经化学改性直接用作反相高效液相色谱固定相,能够有效分离5种多环芳香族化合物(苯、萘、联苯、菲和芘)。     

高稳定性介孔MgO-ZrO_2固体碱的制备及其高温CO_2吸附性能

以无机盐Zr(NO3)4与Mg(NO3)2为原料,聚氧乙烯-聚氧丙烯-聚氧乙烯嵌段型聚醚(P123)作模板剂,合成了纳米介孔MgO-ZrO2复合材料,并通过XRD、N2吸附-脱附、CO2-TPD、TG等方法对材料进行了表征。结果表明,合成的MgO-ZrO2具有介孔结构,比表面积较大;且材料在反复CO2吸附-脱附应用过程中,能够完全再生。此外,材料具有典型的固溶体结构,Mg2+进入四方相ZrO2晶格中并取代Zr4+,形成了一种特殊碱性位。这种碱性位与基体结合牢固,不易流失。考察了MgO-ZrO2材料在150℃高温下的CO2吸附性能,发现材料具有较高的吸附速率(0.084 mmol/(g.min))和吸附量(1.01 mmol/g),是一种可循环利用的吸附材料。     

PEO—PPO—PEO三嵌段共聚物自组装行为的耗散粒子动力学模拟

采用耗散粒子动力学方法（DPD）,模拟了聚氧乙烯-聚氧丙烯-聚氧乙烯（PEO—PPO—PEO）三嵌段共聚物在乙醇溶液中的自组装行为,考察了该共聚物的体积分数和聚氧乙烯（PEO）嵌段链长对介观形貌的影响。当F88（PEO104-PPO39-PEO104）体积分数为20％时,胶柬由初始的均衡分散态逐渐聚合,最终形成PPO为核、PEO为壳的平衡态柱状团聚体。改变共聚物的体积分数和PEO链的长度,会形成不同的介观结构,如：球状、柱状、立体网络、层状和穿孔状结构等。结果表明,DPD方法是研究三嵌段共聚物自组装行为和介观结构形成机理的有效工具,对合成具有特定结构性能的材料有一定的指导意义。     

TPAOH处理制备的微介孔催化剂物化性质与噻吩烷基化性能研究

采用不同浓度的TPAOH溶液处理不同SiO_2/Al_2O_3物质的量比的HZSM-5分子筛,制备了微孔-介孔多级孔HZSM-5催化剂。结果表明,采用不同浓度的TPAOH溶液处理不同SiO_2/Al_2O_3物质的量比的HZSM-5分子筛能够脱出HZSM-5分子筛的骨架硅而产生介孔,介孔孔径随TPAOH溶液浓度和SiO_2/Al_2O_3物质的量比的增大而增大;TPAOH溶液处理能够调变HZSM-5催化剂的酸性。采用不同浓度的TPAOH溶液处理SiO_2/Al_2O_3物质的量比分别为50、80和150的HZSM-5分子筛,其中,SiO_2/Al_2O_3物质的量比为50的HZSM-5弱中酸酸强度、相对酸量、B酸和L酸含量明显高于SiO_2/Al_2O_3物质的量比为80和150的HZSM-5分子筛。经不同浓度的TPAOH溶液处理后SiO_2/Al_2O_3物质的量比为50的HZSM-5催化剂具有最佳的噻吩烷基化反应性能。     

3-(三聚氧乙烯)取代聚噻吩的合成与聚集增强发光

通过2-溴-5-碘-3-(三聚氧乙烯)取代噻吩大分子单体的合成、镍催化缩聚等,得到Mn为6000的3-(三聚氧乙烯)取代聚噻吩(P3OET).在非选择性良溶剂四氢呋喃中,P3OET溶液发射橙色荧光.在选择性极性溶剂诱导作用下,P3OET在水中自组装形成稳定的球形自组装体,荧光峰相对红移而发射橙红色光,伴随荧光强度减弱;而在甲醇中,P3OET形成丝状自组装体,荧光峰相对蓝移而发射亮黄色光,但是荧光强度增强,表现出聚集增强发光现象.类似于含有低聚氧乙烯短支链的聚烯烃,P3OET在水溶液中还具有温度响应特性.当水溶液温度升高,荧光峰逐渐蓝移,并且荧光强度增强.P3OET自组装体可进入小鼠黑色素瘤B16F10细胞,并且发光而用于成像.利用控温热台适当加热细胞,或者使用解偶联剂、抗癌药物等化学刺激使细胞活动产生热量时,发光性质随细胞温度升高而发生蓝移、强度增强等规律性变化.     

SiO2阶层多孔结构搭建及块体材料制备机理

借助溶胶-凝胶结合相分离和模板法进行了阶层多孔结构的搭建及二氧化硅多孔块体材料的制备,表征了阶层多孔块体的显微结构及孔结构特性,分析了阶层多孔结构的搭建机理。研究结果表明,三嵌段共聚物聚环氧乙烷-聚环氧丙烷-聚环氧乙烷（P123）的加入不仅诱导共混体系发生相分离,调控大孔结构的形成,同时形成球形胶束并作为模板剂进入骨架,而1,3,5-三甲基苯（TMB）的加入使P123形成的胶束膨胀且更加稳定,在骨架上成功引入了球形介孔,骨架中凝胶粒子相互聚集形成微孔,从而搭建贯通大孔-球形介孔-微孔同时分布的阶层多孔结构,并获得相应的多孔块体材料;当正硅酸甲酯（TMOS）：P123：TMB摩尔比为1：0.015：0.353时,多孔块体材料的阶层多孔结构最优,大孔孔径为0.5-1.5 μm,介孔孔径为3-4 nm,显气孔率66.1%,比表面积为616 m²·g^-1。     

基于剪切增稠液体防护装甲的研究

综述了剪切增稠液体(Shear Thickening Fluid,即STF)的基本性质、组成成分、流变机理,影响STF流变性能的诸多因素以及对STF流变性能的研究方法,介绍了STF中聚乙二醇(PEG)/纳米SiO2颗粒体系和SiO2的制备方法,对PEG/SiO2的增稠机理进行了讲解。在对STF研究的基础上,阐述了STF-织物组成的液体防护装甲的优异防护性能、防弹和防刺(防锥、防刀)机理,讲述了STF-Kevlar构成的液体防护装甲及防刺机理,介绍了动态防刺测试和准静态防刺测试,最后对液体防护装甲未来研究方面进行了展望。     

载有卟啉的介孔SBA-15表面光电压的性质研究

用表面光电压谱(SPS)和场诱导表面光电压谱(FISPS)技术对比研究了卟啉和介孔SBA-15及载有卟啉的介孔SBA-15的表面光伏特性.固载后同时显示了卟啉和介孔的光电压性质,但是光电压响应强度减弱,这是因为卟啉和介孔之间发生了电子传递的缘故.在外电场诱导下,它们的光伏响应强度随外加正电场光伏响应强度的增加而增强,随外加负电场光伏响应强度的增加而减弱.而装载后的SBA-15在334和425 nm处的光伏响应信号随外加电场的变化而有不同的变化.     

三嵌段共聚物EO20PO70EO20相分离行为的耗散粒子动力学模拟

采用耗散粒子动力学(DPD)方法研究了嵌段共聚物EO₂₀PO₇₀EO₂₀(P123)在水、乙醇/水溶液及二氧化硅溶胶体系中的相分离行为. 不同质量分数的P123在水溶液中共形成4种相分离状态: 球状胶束(10%); 椭球胶束(20%)、棒状胶束(30%)和三维立方胶束(50%). 在模板剂质量分数为10%的乙醇/水溶液中, 模板剂胶束稳定性随着乙醇含量的增加而变差. 在二氧化硅溶胶体系中, 模板剂质量分数低于5%时无胶束形成; 模板剂质量分数增至10%时, P123发生相分离形成三维球状胶束; 随着模板剂质量分数的进一步增加, 模板剂分子夹含着水分子形成三维椭球状结构(20%)、三维立方结构(40%)和层状结构(60%). 模拟结果与实验结果一致, 说明DPD模拟可以从计算角度推测模板剂对介孔材料结构的影响.     

Concerted effect of boron and porosity on shear thickening behavior of hybrid mesoporous silica dispersions

In the present work, the influence of porosity and boron on shear thickening behavior of hybrid mesoporous silica has been studied. Three different levels of boron modification were performed by varying the molar composition of boric acid viz., 1.5 mmol, 2.5 mmol, and 3.5 mmol in a co-condensation approach. The incorporation of boron in mesoporous silica network was confirmed by various techniques such as Fourier transform infra-red (FTIR), and ¹¹B solid- state nuclear magnetic resonance (NMR) spectroscopy. The morphology and particle size were confirmed by using scanning and transmission electron microscopy. To evaluate the effect of boron and porosity on the shear thickening behavior, dispersions were prepared from mesoporous boron- modified silica (MSiB), control mesoporous silica (MSi), non-porous boron-modified silica (SiB), and control non-porous silica (Si) in polyethylene glycol. The shear thickening behavior was studied using steady shear rheology. The dispersion prepared from different loadings of synthesized MSiB containing 1.5 mmol boron showed more than 16 times increase in viscosity (657.7 Pa.s) compared to that of MSi (39.2 Pa.s) at a fairly low volume fraction (φ = 0.15) of silica. It is expected that the highly ordered mesoporous architecture of hybrid silica has improved the interaction between the particle and the dispersing medium through hydrogen bonding. The porous morphology of the hybrid mesoporous silica as well as the incorporation of boron in the silica network favors the formation of a frictional contact network, and a transition from continuous shear thickening (CST) to discontinuous shear thickening (DST) behavior was observed. Therefore, silica prepared via incorporation of boron as well as porosity can be material of interest in variety of applications, for example, soft body armors, sporting goods, and shear thickening electrolytes for high impact resistant batteries.     

Synergic effects of imidazolium ionic liquids on P123 mixed micelles for inducing micro/mesoporous materials

A series of micro/mesoporous silica composites were synthesized with P123 and imidazolium ILs ([C(n)mim]X) as the co-templates. [C(n)mim]X showed notable synergic interaction with P123. By changing the alkyl chain length n in methylimidazolium, ring-like micropores were observed in the wall of the mesoporous materials when n = 4. While increasing n to 10, micropores and mesopores were found in different separated regions. Various anions of Cl(-), Br(-), and BF(4)(-) of ILs have little effect on the aggregation behavior of P123/C4X mixed micelles. The strong hydrogen bonding effect of BF(4)(-) has resulted in the ordered mesoporous channels with numerous micropores in the wall at a low temperature of 313 K. Hydrophobic C4PF(6) can only be solubilized in the core of P123 micelles, which resulted in the swelling of P123/C4PF(6) mixed aggregates and the ordered hexagonal porous silica materials at 313 K. The fundamental understanding of the synergic interaction and formation mechanisms of various porous silica materials can provide a general convenient way toward a rational design and synthesis of the micro/mesoporous composites.     

Viscoelasticity of Shear Thickening Fluid Based on Silica Nanoparticles Dispersing in 1-butyl-3-methylimidizolium Tetrafluoroborate

The viscoelasticity of shear thickening fluid (STF), a crucial property in the protective composite applications, with different silica nanoparticle concentrations in ionic liquid, 1-butyl-3-methylimidizolium tetrafluoroborate ([C₄min]BF₄), was studied at different temperatures and with shear frequencies through oscillatory shear, respectively. All STFs present strain thickening behavior. With increasing silica nanoparticle concentration, the critical shear strain for the onset of strain thickening decreased, while the complex viscosity, storage modulus, and loss modulus increased significantly. The critical shear strain increased with an increase of temperature, while the complex viscosity, storage modulus, and loss modulus decreased notably. The critical shear strain was constant with increasing the frequency of strain, while the complex viscosity decreases slightly. The storage modulus and loss modulus were independent with frequency in the strain thickening region. Nanoparticle clusters leading to strain thickening were demonstrated. The viscoelastic response of STFs to varying silica nanoparticle content, temperature, and frequency investigated here will help to design the specific application of STFs in soft protective composites and damping devices.     

Ultrafast enzyme immobilization over large-pore nanoscale mesoporous silica particles

By finely tuning the TEOS/P123 molar ratio of the octane/water/P123/TEOS quadruple emulsion system and by controlling the synthesis conditions, an ultrafine emulsion system was isolated, under the confinement of which, nanoscale silica particles with ordered large mesopores (approximately 13 nm) have been successfully constructed; the obtained mesoporous silica particles have an unusual ultrafast enzyme adsorption speed and the amount of enzyme that can be immobilized is larger than that of conventional mesoporous silica, which has potential applications in the fast separation of biomolecules.     

Ag-nanoparticle-loaded mesoporous silica: spontaneous formation of Ag nanoparticles and mesoporous silica SBA-15 by a one-pot strategy and their catalytic applications

A facile one-step method was proposed for the successful synthesis of Ag-nanoparticle-loaded mesoporous silica SBA-15 composites, where silver ions and their corresponding reductant aniline were added in the traditional synthetic system of mesoporous silica SBA-15 containing P123 as the surfactant and TEOS as the silica source. Mesoporous silica SBA-15 and Ag nanoparticles were spontaneously formed with Ag nanoparticles embedded in channels and even implanted in frameworks of mesoporous silica SBA-15. A tentative formation process was then proposed according to experimental observations. Furthermore, catalytic activities of Ag-nanoparticle-loaded silica SBA-15 composites toward the reduction of 4-nitrophenol in the presence of NaBH(4) and the reduction of H(2)O(2) were also investigated.     

Morphological and structural evolution of mesoporous silicas in a mild buffer solution and lysozyme adsorption

Mesoporous silicas with various morphologies and structures were synthesized with the aid of 2,2,4-trimethylpentane (TMP) in the presence of nonionic surfactant P123 [(EO)20(PO)70(EO)20] as a structure-directing agent under mild reaction conditions (HAc-NaAc buffer solution, pH 4.4). The ropelike particles formed by end-to-end interconnected nanorods were obtained at a TMP/P123 weight ratio of 0.5. It is noteworthy to mention that the mesoporous nanorods have channels running parallel to the short axis. The silica hollow spheres can be obtained at a higher TMP/P123 weight ratio because of the fusion of the primary nanorods around the interface of the O/W emulsion. Initial synthesis temperatures of 15, 25, and 40 degrees C can lead to mesoporous silicas with highly ordered 2D hexagonal mesostructure, vesicular mesostructure, and mesostructured cellular foams (MCF), respectively. The mesoporous silicas exhibit high adsorption capacity (up to 536 mg g(-1)) and very rapid (<5 min to reach equilibrium) lysozyme immobilization. More importantly, it is revealed that mesoporous silica hollow spheres with rugged surfaces can greatly accelerate the adsorption rate of the enzyme during the adsorption process.     

Fabrication of mesoporous silica/polymer composites through solvent evaporation process and investigation of their excellent low thermal expansion property

We fabricate mesoporous silica/epoxy polymer composites through a solvent evaporation process. The easy penetration of the epoxy polymers into mesopores is achieved by using a diluted polymer solution including a volatile organic solvent. After the complete solvent evaporation, around 90% of the mesopores are estimated to be filled with the epoxy polymer chains. Here we carefully investigate the thermal expansion behavior of the obtained mesoporous silica/polymer composites. Thermal mechanical analysis (TMA) charts revealed that coefficient of linear thermal expansion (CTE) gradually decreases, as the amount of the doped mesoporous silica increases. Compared with spherical silica particle without mesopores, mesoporous silica particles show a greater effect on lowering the CTE values. Interestingly, it is found that the CTE values are proportionally decreased with the decrease of the total amount of the polymers outside the mesopores. These data demonstrate that polymers embedded inside the mesopores become thermally stable, and do not greatly contribute to the thermal expansion behavior of the composites.     

Apparent shear strength of hybrid glass fibre reinforced composite joints

The incorporation of nano or micro ceramic particles into fibre reinforced composites (FRC) to enhance their stiffness and durability has been widely investigated. This mechanism has been attributed to the increase in stiffness of the polymeric matrix phase and shear strength of FRCs due to the presence of particles at the interlaminar regions. In order to elucidate such effect, hybrid single-lap joints consisted of ceramic particles and glass fibre reinforced composites were evaluated to better assess the mechanical interlocking effect provided by silica and cement inclusions. A full factorial design (2³) was performed to identify the effect of the type of particle (silica and cement), particle weight fraction (2.5 and 5 wt%) and glass fibre grammage (200 and 600 g/m²) on the apparent shear strength and adherent strength of single-lap joints under tensile loading. The ceramic particle inclusions led to increased apparent shear strength and adherent strength. The inclusion of 5 wt% ceramic particles into 600 g/m² cross-ply glass fibre composites enhanced both adherent and apparent shear strengths.     

温度对介孔二氧化硅形貌和介相结构有序性的影响

1992年Kresge等科学工作者首次报道了一种新颖的介孔二氧化硅材料,介孔二氧化硅的合成及其性能表征引起了广泛的研究兴趣[1,2]。这种材料由于具有高比表面积(1000~1400m2·g-1)、孔道排列有序、孔径分布窄并可以在2~10nm范围内可调等优点,所以有望用于催化与吸附、化学传感、纳