Thin-layer chromatography of inorganic ions on polyethyleneimine cellulose in sulfuric acid and acid-ammonium sulfate media

Summary The thin-layer chromatographic behavior of 49 inorganic ions on polyethyleneimine (PEI) cellulose, a weakly basic anion-exchanger, has been systematically studied in sulfuric acid and ammonium sulfate media (both 0.01–1.0 moldm⁻³). The sorption on the cellulose decreases with increasing concentration of the acid or sulfate for most of the ions and to a lesser extent for Hg(II), Bi(III), Th(IV), Nb(V), and U(VI). The R_f values of Pd(II), Ru(III), Au(III), Pt(IV), and Ta(V) are extremely low in both systems. Ba(II), Pb(II), Sb(III), Mo(VI), and W(VI) are also strongly retained on the layer. Oxy-anions such as As(III) and Se(VI) are not adsorbed on the cellulose to any great extent, but Re(VII) distributes on the plate with a R_f value of about 0.5. The characteristic retention on PEI-cellulose layer of several polyvalent ions, which form anionic sulfato complexes, can be observed in ammonium sulfate media. Possibilities for separations of analytical interest are also demonstrated in both systems.     

Chromatography of inorganic ions on polyethyleneimine cellulose layer in hydrochloric acid — Ammonium thiocyanate media

Summary Thin-layer chromatographic behavior of 58 inorganic ions on polyethyleneimine (PEI) cellulose has been systematically surveyed in hydrochloric acid — ammonium thiocyanate media. In this media most of the ions distribute chromatographically on the layer. Ag(I), Hg(II), Pd(II), Au(III), Bi(III), Ru(III), Pt(IV), Nb(V), Ta(V), Mo(VI), and W(VI) are strongly retained, while alkali earths(II), Mg(II), As(III), Ti(IV), and Te(VI) are not absorbed to any great extent in this system. An interesting correlation was found between the R_f values on PEI-cellulose in the thiocyanate media and the paramagnetic moment of the rare earths(III). An oddeven fluctuation against the atomic number is also found for the heavy rare earths(III). Chromatographic separation of many inorganic ions of analytical interest is demonstrated in this system.     

Chromatography of inorganic ions on cellulose phosphate layer in hydrochlorid acid and in acid ammonium thiocyanate media

Summary Thin-layers of an intermediately acidic cation exchanger, cellulose phosphate (P-cellulose), have systematically been used to study the chromatographic behavior of 58 inorganic ions in both hydrochloric acid and acid ammonium thiocyanate media (0.01–2.0 mol dm⁻³). In both solvent systems, the R _f values of many bivalent cations increase with increasing concentration of the acid and thiocyanate. Polyvalent metal ions including beryllium (II) and the others are strongly retained on the P-cellulose in the acid and thiocyanate systems tested. Palladium(II), mercury(II), ruthenium(III), rhenium(VII), arsenic(III), selenium(IV) and tellurium(IV) are not adsorbed on P-cellulose to any great extent. For silver(I), indium(III), gold(III), and platinum(IV), there are marked differences in the chromatographic behavior between hydrochloric acid and acid ammonium thiocyanate systems. Multicomponent separations conducted on P-cellulose plates with these eluents are presented.     

The chromatography of metals on DEAE-cellulose layers in phosphoric acid media

The adsorption behaviour of forty-eight metals on DEAE-cellulose thin layers has been examined in aqueous phosphoric acid media. R_F values are given as a function of phosphoric acid concentration over the range 0.01–1.0 M and are compared with those obtained in a similar manner with a crystalline cellulose, Avicel SF. Particularly strong retention on DEAE-cellulose occurred for Mo(VI), W(VI), Re(VII), the platinum group metals, Au(III) and Bi(III). Weak to moderate retention was also observed for several metals, such as V(V), Fe(III), Se(IV), In(III), the rare earths and U(VI), at lower concentrations of phosphoric acid (<0.1 M).     

Thin-Layer chromatography of inorganic ions on cellulose phosphate in sulfuric acid-organic solvent media

Summary Thin-layer chromatographic behavior of 49 inorganic ions on cellulose phosphate (P-cellulose) has systematically been surveyed with binary solvent mixtures consisting of sulfuric acid and an organic solvent such as methanol or acetone. The R_f values of many bivalent and monovalent ions as well as Te(VI) decrease on the P-cellulose layer with an increasing concentration of the organic solvent. Polyvalent ions which form strong phosphato-complexes and precipitate insoluble sulfate are strongly retained on P-cellulose. Oxy-anions, Au(III) and Pt(IV) are not adsorbed on the cellulose to any great extent. Feasibilities of the separation of multicomponent mixtures are demonstrated on the P-cellulose layer.     

The chromatography of a number of metals on cellulose phosphate layers in sulfuric acid and ammonium sulfate media

Summary The thin-layer chromatographic behavior of 58 metals on an intermediately acidic cation exchanger, cellulose phosphate (P-cellulose), has been surveyed systematically in sulfuric acid and ammonium sulfate media (0.01–2.0 M). The R_f values for many bivalent and univalent metal ions on P-cellulose plates increase with increasing concentration of sulfate ions. Howerver, manganese (II), arsenic (III) and selenium (IV) are not adsorbed on the cellulose to any great extent. Beryllium (II) and other metals, which form either strong phosphate complexes or insoluble sulfate precipitates, are strongly retained on the P-cellulose. The thin-layer chromatographic separations of various metal ions of analytical interest were accomplished to demonstrate the use of R_f measurements for predicting separations in the acid and the sulfate media.     

Extraction of molybdenum(V) as its ferron complex with trioctylamine in chloroform from a sulphuric acid medium

A simple, rapid, and highly selective method for the separation of molybdenum from a large number of elements of analytical importance has been developed. The method is based on the extraction of a Mo(V)-ferron (7-iodo-8-hydroxyquinoline-5-sulphonic acid) complex into trioctylamine-chloroform in a sulphuric acid medium using ascorbic acid as a reductant. Many elements such as Re(VII), W(VI), U(VI), Th(IV), Cr(III), Cr(VI), V(V), Ce(IV), Ru(III), Co(II), Ni(II), Mn(II), Fe(II), Fe(III), Cd(II), Mg(II), Cu(II), Al(III), Zn(II), Pb(II), Ag(I), and As(V) are not extracted under the conditions proposed and, thus, molybdenum can be easily separated without any interference. Sulphate, chloride, nitrate, phosphate, and oxalate anions have no effect on the extraction of molybdenum. However, zirconium and palladium interfere seriously. The ratio of Mo: ferron: TOA in the extracted species is found to be 1: 1: 3 using Job’s method of continuous variations. This value has been further confirmed by the mole-ratio method. The text was submitted by the authors in English.     

Chromatographic behaviour of a number of metal ions on DEAE-cellulose layers in thiosulfate media

The adsorption behavior of 47 metal ions on DEAE-cellulose (Cl⁻) has been surveyed in aqueous thiosulfate solution by thin-layer chromatographic technique. The R_f values are measured as a function of thiosulfate concentration (0.010–2.0M) and are compared with those obtained on a microcrystalline cellulose Avicel SF. Generally, the ion-exchange adsorption of metal ions are weak or moderate over the thiosulfate concentration range tested except for a few metal ions like Mo(VI), Sb(III), Bi(III) etc., which have high preference to DEAE-cellulose. A variety of chromatographic distribution exhibited by metal ions allows to develop a number of separations of analytical and radiochemical interest.     

Luminol-K2S2O8体系中金属离子化学发光行为的研究

报导了在自行设计的流动注射式化学发光分析仪上,对Luminal-K2S2O8体系中32种金属离子的化学发光行为的系统研究.确定了对金属离子的最优测定条件以及大多数金属离子的检出极限和线性范围.     

Dibenzo[b,f]oxepin‐10(11H)‐one and dibenzo[b,f]thiepin‐10(11H)‐one as useful synthons in the synthesis of various dibenzo[e,h]azulenes

The present review focuses on dibenzo[b,f]oxepin‐10(11H)‐one ( I , X = O) and dibenzo[b,f]thiepin‐10(11H)‐one ( I , X = S) as common synthons in the efficient synthesis of various dibenzoxepino[4,5‐ and dibenzothiepino[4,5]‐fused five‐membered heterocycles: [2,3] fused thiophene ( II ), [3,4] fused thiophene ( III ), furan ( IV ), pyrrole ( V ), imidazole ( VI ), pyrazole ( VII ), oxazole ( VIII ), and thiazole ( IX ). The potential of I to be converted into reactive intermediates that readily undergo heteroaromatic annulation reactions by cyclocondensation with proper binucleophiles allows formation of a range of enumerated functionalized dibenzo[e,h]azulene [4] structures ( II , III , IV , V , VI , VII , VIII , IX ). Dibenzo[e,h]azulenes as heterotetracyclic scaffold can be exploited in further modifications to obtain compounds with altered physicochemical and biological profile. J. Heterocyclic Chem., (2012).     

Anion-exchange behavior of various metals in hydrazoic acid media

The adsorption characteristics for 43 metals on a strongly basic ion-exchange resin Bio-Rad AG1 were examined in 0.5 M hydrazoic acid solution. The distribution coefficients for V(IV), Fe(III), Cu(II), Zn, Se(IV), Mo(VI), Pd(II), Cd, In(III), Rc(VII), Hg(II) and U(VI), which showed very strong adsorption except for Cd, were measured as a function of hydrazoic acid concentration over the range 0.05–0.5 M. Favorable differences in the distribution coefficients allow useful two- and three-component separations such as Co(II)-Fe(III), As(III)-V(IV), Cd-Zn, Cd- Hg(II), Te(IV)-Se(IV), Th-U(VI), Mn(II)-Mo(VI)-Re(VII), to be achieved on a small column.     

Adsorption of radiocobalt on lead dioxide from aqueous solution

Adsorption of cobalt on lead dioxide from aqueous solutions has been studied in relation to shaking time, amount of adsorbent, pH, and concentration of the adsorbate. The data fitted very well Langmuir, Freundlich, and Dubinin-Radushkevich isotherms and their corresponding constants were calculated. In another set of experiments the influence of different anions and cations on the adsorption of cobalt under the optimum experimental conditions have been determined. EDTA, tartrate, citrate, thiocyanate, oxalate, U(VI), Al(III), Fe(III), Cr(III), and Th(IV), drastically reduced adsorption of cobalt. Therefore these anions and cations should be removed before adsorption of cobalt on lead dioxide. Adsorption of other metal ions on the oxide were measured under identical conditions. TheK _D values indicate that cobalt can be separated successfully from Hg(II), Ag(I), Ta(V), In(III) and Tc(VII).     

Preparation, characterization and application of an cellulose ion-exchanger with acetoacetamide functional groups

Summary A method is described for functionalizing acetoacetamide chelating groups onto microcrystalline cellulose (Cell-AcAc). This material shows a significant affinity for Fe(III), Cu(II) and U(VI) and no or very less affinity for the M(I) ions (M=Na, K), M(II) ions (M= Mg, Ca; Fe, Co, Ni, Zn), La(III) and Y(III) including Th(IV). The obtained K _d values offer a column separation method for U(VI) ions from the rest of above-mentioned metal ions except Fe(III). Cell-AcAc and its Cu(II) complexes are characterized by means of FT-IR spectra.

---

Darstellung, Charakterisierung und Anwendung von Ionenaustauschmaterial aus Cellulose mit chemisch gebundener Acetoacetamid-Gruppe

Zusammenfassung Die Darstellung von immobilisiertem Acetoacetamid auf mikrokristallinem Cellulosepulver (Cell-AcAc) wird beschrieben. Der Ionenaustauscher Cell-AcAc hat eine ausgeprägte Affinität für Fe(III), Cu(II) and U(VI), aber nahezu keine für die M(I)-Ionen (M=Na, K) M(II)-Ionen (M=Mg, Ca; Fe, Co, Ni, Zn), La(III), Y(III) sowie Th(IV). Die erhaltenen K _d-Werte ermöglichen für U(VI)-Ionen eine quantitative säulen-chromatographische Trennung von den anderen genannten Kationen mit Ausnahme von Fe(III). Das Ionenaustauschmaterial Cell-AcAc und sein Cu(II)-Komplex wurden durch FT-IR-Spektren charakterisiert.

     

Voltammetry and controlled-potential coulometry with boron carbide electrodes

With the boron carbide electrode, E_{p$\text{p}\text{2}$} values were determined for the reduction of the following ions: Cd(II), Co(II), Cu(II), Fe(III), Ni(II), Pb(II), Ru(IV), Sb(V), and U(VI). The linear dependence of peak current on concentration is demonstrated for the U(VI) → U(IV) and Fe(III) → Fe(II) reductions at the boron carbide electrode. The suitability of the electrode for the controlled-potential coulometric ti trations of Fe(II) → Fe(III), Fe(III) → Fe(II), and U(VI) → U(IV) was studied; the results were inconclusive because of the small surface area that could be used conveniently and the possibility of oxygen leaks in the cell.     

Über Pterinchemie. 65 Mitteilung [1]. Herstellung von (6 R,S)-5,6,7,8-Tetrahydro-L-biopterin, 7,8-Dihydro-L-biopterin,L-Sepiapterin,Deoxysepiapterin, (6 R,S)-5,6-Dihydrodeoxysepiapterin und 2′-Deoxybiopterin

Preparation of (6 R, S)-5,6,7,8-tetrahydro-L -biopterine, 7,8-dihydro-L -biopterine, L -sepiapterine, deoxysepiapterine, (6 R, S)-5,6-dihydrodeoxysepiapterine and 2′-deoxybiopterine We describe the preparation of (6 R, S)-5,6,7,8-tetrahydro-L -biopterine (II) by catalytic- (reported in our short communication [2]) and natriumdithionite reduction of L -biopterine (I) and a preparation of 7,8-dihydro-L -biopterine (IV) by treatment of L -biopterine (I) with natriumdithionite. Whereas oxidation of tetrahydrobiopterine II in the presence of oxygen leads to L -sepiapterine (III), dihydrobiopterine IV in acetic acid without oxygen gives deoxysepiapterine (VII), 5,6-dihydro-deoxysepiapterine (VI) and 2′-deoxybiopterine (V) by a disproportionation reaction.     

Extractive separation of molybdenum as Mo(V) xanthate from Iron, vanadium, Tungsten, copper, uranium and other elements

A simple and selective extraction of molybdenum is described. Tungsten is masked with tartaric acid and molybdenum(VI) is reduced in 2M hydrochloric acid by boiling with hydrazine sulphate. Iron, copper and vanadium are then masked with ascorbic acid, thiourea and potassium hydrogen fluoride respectively. The molybdenum(V) is extracted as its xanthate complex into chloroform, from 1M hydrochloric acid that is 0.4M potassium ethyl xanthate. The complex is decomposed by excess of liquid bromine, and the molybdenum is stripped into alkaline hydrogen peroxide solution. The molybdenum is then determined by standard methods. Large amounts of Cu(II), Mn(II), Fe(III), Ti(IV), Zr, Ce(IV), V(V), Nb, Cr(VI), W(VI), U(VI), Re(VII) and Os(VIII) do not interfere. Several synthetic samples and ferromolybdenum have been rapidly and satisfactorily analysed by the method.     

A chelating resin containing 1-(2-thiazolylazo)-2-naphthol as the functional group; synthesis and sorption behavior for trace metal ions

A new polystyrene-divinylbenzene resin containing 1-(2-thiazolylazo)-2-naphthol (TAN) functional group was synthesized and its sorption behavior for 19 metal ions including Zr(IV), Hf(IV) and U(VI) was investigated by batch and column experiments. The chelating resin showed a high sorption affinity for Zr(IV) and Hf(IV) at pH 2. Some parameters affecting the sorption of the metal ions are detailed. The breakthrough and overall capacities were measured under optimized conditions. The overall capacities of Zr(IV) and Hf(IV) that were higher than those of the other metal ions were 0.92 and 0.87 mmol/g, respectively. The elution order of metal ions at pH 4 was evaluated as: Zr(IV)>Hf(IV)>Th(IV)>V(V)>Nb(V)>Cu(II)>U(VI)>Ta(V)>Mo(VI)>Cr(III)>Sn(IV)>W(VI). Quantitative recovery of most metal ions except Zr(IV) was achieved using 2 M HNO₃. Desorption and recovery of Zr(IV) was successfully performed with 2 M HClO₄ and 2 M HCl.     

Spectrophotometric and chromatographic determination of sulfanilamides in biological fluids and pharmaceuticals

The conditions for the determination of norsulfazol (I), sulfadimezine (II), ethazole (III), sulfamethoxypyridazine (IV), sulfadimethoxine (V), sodium sulfacyl (VI), sulfalene (VII), sulgin (VIII), and bucarban (IX) as their derivatives of 4,6-dinitrobenzofuroxan using spectrophotometry and thin-layer chromatography were selected. The best results were obtained at 490–500 nm using polar solvents and their aqueous mixtures of pH 6.68 as analytical media. The analytical range for sulfanilamides was 0.5–6.0 Μg/mL. The limits of detection (Μg/mL) were 0.24 for 1,0.28 for II, 0.43 for III, 0.18 for IV, 0.25 for V, 0.54 for VI, 0.54 for VII, 0.17 for VII, and 0.31 for IX. Sulfanilamides were determined in Pharmaceuticals (tablets, ointments, and drops) and biological fluids (protein hydrolyzates, urine, blood serum, and whole blood). A simple rapid method for the determination of the phenotype of biotransformation by the type of acetylation was developed based on the studies of the kinetics of the excretion of II from the human body with urine.     

Oximidobenzotetronic acid as a reagent for the separation and gravimetric determination of palladium and cobalt

Oximidobenzotetronic acid is recommended for the separation and gravimetric determination of palladium and cobalt An ethanolic solution of the reagent quantitatively precipitates palladium(II) from solutions which are 0.75 N in acid up to pH 5.1, the complex is weighed as Pd(C₉H₅NO₄)₂. Cobalt(II) can be determined in the filtrate after the precipitation of palladium. With 0.5 N acid solutions, no interference was found from Pt(IV), Ir(IV), Rh(III), Ru(III), Os(IV), Au(III), Ag(I), Cu(II), Fe(III), Ni(II), Hg(II). Pb(II), Bi(III), Cd(II), As(V), Se(VI), Te(IV), Mo(VI), Sb(III), Al(III), Cr(III), Zn(II), Ti(IV), Zr(IV). acetate, oxalate, citrate, tartrate, phosphate and fluoride.     

Electrometric titrations of Cr(VI), Mn(IV), V(V), Co(III) and U(VI) with a standard iron(II) solution in alkaline media containing hexitols

Direct and indirect potentiometric, bipotentiometric and biamperometric titrations with a standard iron(II) solution are described for some inorganic compounds in alkaline media containing hexitols (mannitol, dulcitol and sorbitol). The optimal conditions for titrations based on the Cr(VI) → Cr(III), Mn(IV) → Mn(III) → Mn(II), V(V) → V(IV), Co(III) → Co(II) and U(VI) → U(IV) systems are discussed. Of the hexitols studied, sorbitol has the greatest effect on the value of the redox potential of the Fe(III)/Fe(II) system; the E_f° value is about —1.10 V vs. SCE.