在CdS水悬浮液中O2光吸收的pH效应

为了深入了解间接光腐蚀过程, Grätzel等人曾考察过O₂在CdS和Rh₂0₃/CdS 悬浮液(pH=9)中光吸收行为, 发现光照生成的SO₄^2-的µmol数值基本上为加入O₂的µmol数值的一半, 且反应后悬浮液的pH降低^[3]。     

CdS超薄片层包覆TiO2中空结构复合材料的形成和应用

本实验以钛酸四丁酯为钛源,醋酸镉为镉源,利用静电纺丝的方法制备了直径~250 nm的电纺丝纳米纤维。通过高温煅烧和硫化钠溶液进行水热处理,得到CdS超薄片层包覆TiO₂中空结构的纳米纤维。推测该复合结构形貌的形成过程为:在Ti/Cd(摩尔比)为1:1和2:1时,由于CdO的含量较高,反应过程中CdO溶解,并与反应溶液中的S^2-形成CdS超薄片层生长在纤维的外表面,剩余的TiO₂纳米粒子聚集形成中空的纳米管状结构;而Ti/Cd(摩尔比)为4:1和8:1时,由于溶解的CdO较少不足以形成TiO₂纳米管,同时,生成的CdS也不足以完全包覆TiO₂纳米纤维形成非管状结构。当Ti/Cd为1:1时,TiO₂@CdS复合材料具有最好的产氢活性。在300 W氙灯光照条件下和加UVCUT-420 nm滤光片下,50 mg催化剂产氢速率分别为19.7 μmol/h和3.4 μmol/h,这主要是由于所得到的复合结构中TiO₂为非晶材料。进一步在惰性气氛下煅烧,也很难将TiO₂晶化。     

富镉离子CdS量子点电化学发光法检测L-半脐氨酸

采用一锅法,通过控制镉硫比合成了表面富镉离子的硫化镉量子点,利用L-半胱氨酸可与量子点表面Cd2+结合,使量子点表面钝化,从而增强其电化学发光信号的性质,实现了对L-半胱氨酸的选择性检测.对合成的量子点进行了表征,优化了检测条件.在优化的条件下,L-半胱氨酸在5.0×10-9~1.0×10-5 mol/L浓度范围内与ECL信号呈良好的线性关系,检出限为1.2×10-9 mol/L(S/N=3).本方法对L-半胱氨酸具有良好的选择性,用于实际样品中L-半胱氨酸的测定,结果令人满意.     

Effect of Reaction Conditions on the Assembly,Structures and Fluorescent Sensing Behaviors of Cd(Ⅱ) Metal-organic Complexes

Three Cd(Ⅱ) metal-organic complexes, namely[Cd(phen)₂Cl₂](1),[Cd(phen)Cl₂](2) and[Cd(phen)(cam)]·H₂O(3)(phen=1,10-phenanthroline, H₂cam=camphoric acid), were hydrothermally synthesized using Cd²⁺, phen and H₂cam as raw materials under different conditions of pH values, reaction temperatures or reactant ratios. The prepared complexes were structurally characterized by means of single-crystal X-ray diffraction, and the results show that complex 1 is a 2D supramolecular complex, which consists of[Cd(phen)₂Cl₂] mononuclear subunits, while complex 2 shows a 1D chain structure, in which Cd(Ⅱ) ions are connected by chloride(Cl^-) bridges, with phen hanging on both sides of the chain. No cam anions have been observed in the structures of complexes 1 and 2. In complex 3, cam connects Cd(Ⅱ) ions to construct a 2D network, in which phen acts as terminal ligands. The adjacent 1D chains for complex 2 and the adjacent 2D layers for complex 3 are further linked by hydrogen bonding interactions or π-π intermolecular interactions to form 3D supramolecular networks, respectively. The effects of reaction conditions on the assembly and structures of the complexes have been discussed. The fluorescent and photocatalytic properties of complexes 1-3 and the fluorescent sensing behaviors of complexes 2 and 3 have also been investigated.     

Switch-on fluorescence sensor for ascorbic acid detection based on MoS2 quantum dots-MnO2 nanosheets system and its application in fruit samples

In this work,molybdenum disulfide quantum dots(MoS_2 QDs) were firstly prepared by hydrothermal method using sodium molybdate and glutathione as precursors,and applied in ascorbic acid detection.When joining MnO_2 nanosheets into MoS_2 QDs solution,they produced an obvious fluorescence quenching,which should be due to inner filter effect(IFE).Meanwhile,the fluorescent probe was formed,Interestingly,we found that this quenching phenomenon disappeared with the addition of ascorbic acid,In other words,the fluorescence gradually restored.This recovery phenomenon is mainly due to the reduction effect of ascorbic acid for MnO_2 nanosheets.Under the optimum conditions,the limit of detection(LOD) of 39 nmol/L for ascorbic acid was achieved with a linear range of 0.33-5.00 μmol/L.The repeatability was better than 5.0% for ascorbic acid in both standard and fruit samples(n = 3).Moreover,the as-fabricated fluorescent sensing system was successfully employed to detect the ascorbic acid levels in hawthorn and jujube with satisfactory results.     

Two New Cadmium Metal-organic Frameworks Based on a Mixed-donor Ligand

The self-assembly of a prominent mixed-donor ligand, 5-[4-(1H-tetrazolyl)phen]isophthalic acid(H₃TZPI), with a Cd²⁺ center generates two new metal-organic frameworks:[Cd(H₂TZPI)₂(H₂O)₂]_n(JUC-163) and[Cd₂(TZPI)(μ₃-OH)(H₂O)₂]·H₂O·DMF(JUC-164). The two complexes demonstrate different structures for the ligand’s different coordination modes and configurations. JUC-163 shows a 2D layer structure and further forms into a 3D supramolecular framework by noncovalent interactions(C-H…O, O-H…N and π…π interactions), whereas JUC-164 exhibits a fascinating 3D framework for the outstanding coordination modes and configurations of the ligand, which are fit for the complex structure. And also, the factor of different cadmium salts(chloride and nitrate) which are used in synthesis progress is worth to notice for the construction of the two distinct structures. The luminescent properties of these metal-organic frameworks were also investigated.     

A sensitive sensor for anthraquinone anticancer drugs and hsDNA based on CdTe/CdS quantum dots fluorescence reversible control

Based on CdTe/CdS quantum dots (CdTe/CdS QDs) fluorescence (FL) reversible control, a new and sensitive FL sensor for determination of anthraquinone (AQ) anticancer drugs (adriamycin and daunorubicin) and herring sperm DNA (hsDNA) was developed. Under the experimental conditions, FL of CdTe/CdS QDs can be effectively quenched by AQ anticancer drugs due to the binding of AQ anticancer drugs on the surface of CdTe/CdS QDs and photoinduced electron transfer (PET) process from CdTe/CdS QDs to AQ anticancer drugs. Addition of hsDNA afterwards brought the restoration of CdTe/CdS QDs FL intensity, as AQ anticancer drugs peeled off from the surface of CdTe/CdS QDs and embedded into hsDNA double helix structure. The liner ranges and the detection limits of FL quenching methods for two AQ anticancer drugs were 0.33-9 μg mL⁻¹ and 0.09 μg mL⁻¹ for ADM and 0.15-9 μg mL⁻¹ and 0.04 μg mL⁻¹ for DNR, respectively. The restored FL intensity was proportional to concentration of hsDNA in the range of 1.38-28 μg mL⁻¹and the detection limit for hsDNA was 0.41 μg mL⁻¹. It was applied to the determination of AQ anticancer drugs in human serum and urine samples with satisfactory results. The reaction mechanism of CdTe/CdS QDs FL reversible control was studied.     

非贵金属三元复合Ni(PO3)2-Ni2P/CdS NPs异质结的构建及可见光高效催化产氢性能

结合异质结构建与共催化剂改性, 以花球状Ni(OH)₂为前驱体, 经热磷酸化后得到Ni(PO₃)₂-Ni₂P二元助催化剂, 借助超声化学合成法, 与CdS NPs复合, 形成非贵金属CdS基三元光催化材料Ni(PO₃)₂-Ni₂P/CdS NPs. 以Na₂S-Na₂SO₃为牺牲剂, 在可见光(λ＞420 nm)照射下, 在不借助任何贵金属的情况下, 负载量为8%(质量分数)的Ni(PO₃)₂-Ni₂P/CdS NPs复合材料的光催化产氢速率达到4237 μmol·g^?1·h^?1, 为CdS NPs(217 μmol·g^?1·h^?1)的19倍. 在产氢循环实验中, 反应进行到第6次循环(18 h)后, 复合材料的产氢速率约为初始的89%, 具有较好的稳定性. 与CdS NPs相比, Ni(PO₃)₂-Ni₂P/CdS NPs的吸收边明显红移, 禁带宽度降至1.86 eV, 并降低了H⁺还原的过电位, 显示出增强的光吸收性能和适宜的带隙结构. 通过Ni(PO₃)₂-Ni₂P与CdS NPs之间的协同效应, 有效促进了光生载流子的分离, 提高了产氢活性和稳定性.     

金属离子对CdS量子点/聚酰胺-胺树形分子纳米复合材料光致发光性能的影响

以聚酰胺-胺树形分子为模板制备了分散好、尺寸均匀的CdS量子点，并用分光光度滴定法研究了Cd²⁺、Zn²⁺、Pb²⁺、Cu²⁺、Mn²⁺几种金属离子对其光致发光性能的影响。发现不同离子对CdS量子点的发光性能影响不同:Cd²⁺和Zn²⁺使量子点荧光增强，Pb²⁺、Cu²⁺和Mn²⁺使其荧光有不同程度淬灭。这归因于金属离子对CdS量子点表面的修饰作用。Cd²⁺能减少由S^2-悬键构成的非辐射复合中心，增强树形分子对量子点表面缺陷的钝化作用，并能在量子点周围形成类肖特基能垒，从而显著增大CdS量子点的光致发光效率。由于ZnS与CdS的晶格参数非常接近，Zn²⁺能起到与Cd²⁺类似的作用，使CdS量子点的发光效率大大增强。Pb²⁺和Cu²⁺能取代Cd²⁺在CdS量子点表面生成窄带隙的壳层，对其发光有很强的淬灭作用。由于块体PbS的带隙比块体CuS窄，故Pb²⁺的淬灭能力强于Cu²⁺。Mn²⁺能破坏Cd²⁺与PAMAM树形分子的配位键，降低树形分子对CdS量子点表面缺陷的钝化作用，且其本身在量子点表面构成了新的荧光淬灭中心，但Mn²⁺也能形成较弱的类肖特基能垒，故对量子点的发光淬灭作用较弱。     

苯二甲酰基桥联铁硫配合物[(μ-RS)Fe2(CO)6]2(μ-OCC6H4CO-μ)的合成及表征

通过由Fe₃(CO)₁₂、RSH和Et₃N所形成的[(μ-CO)(μ-RS)Fe₂(CO)₆]Et₃NH于室温下分别与对或间苯二甲酰氯的原位反应,首次合成6个结构新颖的苯二甲酰基桥联铁硫配合物[(μ-RS)·Fe₂(CO)₆]₂(μ-p-OCC₆H₄CO-p-μ)(R=Et,n-Bu,t-Bu)以及[(μ-RS)Fe₂(CO)₆]₂(μ-m-OCC₆H₄CO-m-μ)(R=n-Pr,n-Bu,t-Bu).经元素分析、IR光谱及¹HNMR表征了它们的结构,并讨论了产物的生成过程.此外,还提出了合成对苯二甲酰氯的一种新方法.     

Solvothermal syntheses and crystal structures of two metal coordination polymers with double-chain structures

Two polymeric complexes, [Cu₂(btec)(phen)₂]_n·(H₂O)_n (1) and [Cd₄(btec)₂(phen)₄(H₂O)₄]_n (2) (H₄btec=1,2,4,5-benzenetetracarboxylic acid; PHEN=1,10-phenanthroline), were synthesized by solvothermal reactions at 140 °C. Both complex 1 and 2 possess infinite double-chain structures, in which each Cu(II) center has a tetrahedral configuration and the Cd(II) centers adopt triangular prismatic and square-based pyramidal configurations simultaneously. The inter-chain face to face π–π interactions among the aromatic rings of phen and the hydrogen bond interactions between aqua molecules and carboxyl O atoms result in 3-D networks in the two complexes. The ESR spectra study of complex 1 shows that there is negligibly small long-range super-exchange interactions between the Cu(II) atoms via benzenecarboxylate bridging.     

含面桥基磷硫配体的新颖三核和四核钌羰合簇

[Ru₃(CO)₁₂]与Lawesson试剂[(MeOC₆H₄PS₂)₂]反应,合成、分离并用谱学表征了产物三核钌羰合簇[(μ-H)₂Ru₃(CO)₉(μ₃-P)](Ⅰ)和四核钌羰合簇[(Ru₄(CO)₁₀(μ₃-S)(μ₃-PC₆H₄OMe)](Ⅰ).X射线衍射测定了的晶体分子结构,表明含有1个裸磷原子作为面桥基配体,并具有颇短的Ru-Ru键距,该价电子数为49e的簇合物对氧和水稳定.谱学分析表明,化合物具有四面体型的Ru₄簇心,其三角形面上分别具有面桥基μ₃-S和μ₃-PC₆H₄OMe基配体.     

Contributions to the basic problems of complexometry—XVII Determination of zinc and cadmium in the presence of each other

A new method for separating cadmium from zinc by precipitation as Cd(phen)₂I₂ is reported. Even very small amounts of zinc can be determined complexometrically in highly ammoniacal media by back-titration of an added excess of DCTA with calcium(II) using Methylthymol Blue as indicator.     

一种新型结构的七核钴原子羰基簇合物的合成与结构研究

C₂H₅SPCl₂与Co₂(CO)₈反应的产物经柱层析分离得3条带,第一条为深棕色,经IR谱、¹HNMR、谱、元素分析、X光单晶结构分析,确定该带产物为七核钴原子簇CO₇(μ₇-S)(μ₄-PSC₂H₅)(μ-SC₂H₅)₂(μ-CO)₂(CO)₁₂,是八面体骨架Co₄PS和四面体骨架Co₃S结合的松散原子簇合物。     

Luminescence properties of CdTe QDs embedded in Zn5(CO3)2(OH)6 matrix

CdTe@Zn₅(CO₃)₂(OH)₆ composites were synthesized by a hydrothermal method. CdTe@Zn₅(CO₃)₂(OH)₆ composite nanospheres were characterized via X-ray diffraction, scanning electron microscopy, energydispersive X-ray spectroscopy, and photoluminescence (PL). The hydrothermal reaction time and the mole ratios of Zn/Te played important roles in the growth and fluorescence intensity of CdTe@Zn₅(CO₃)₂(OH)₆ composites. The composite powders showed peak PL at 578 nm at 1.6 times the intensity of powdered CdTe QDs. CdTe@Zn₅(CO₃)₂(OH)₆ exhibited a strong yellow fluorescence emission, and its preparation method was easy and economical. Therefore, CdTe@Zn₅(CO₃)₂(OH)₆ offers potential applications in biological markers and light-emitting diodes.     

Synthesis,Structure Characteristic and Thermal Behavior of Two New Metal-organic Azo-triazole Compounds: [Zn(phen)3]·ZTO·6H2O and[Cu(phen)3]·ZTO·6H2O

[Zn(phen)₃]·ZTO·6H₂O(1) and[Cu(phen)₃]·ZTO·6H₂O(2) were synthesized by the reaction of Zn(NO₃)₂·6H₂O/Cu(NO₃)₂·3H₂O with 4,4-azo-1H-1,2,4-triazol-5-one(ZTO) and 1,10-phenanthroline(phen). The two compounds were characterized by elemental analysis and IR spectrum analysis, respectively. Compound 1 was also characterized by single crystal X-ray diffraction analysis. For compound 1, the coordination geometry around the Zn²⁺ is a distorted octahedron, with the bite angles of 76.7(3)°-77.6(4)° for all three phen ligands. Moreover, the thermal behaviors and thermal decomposition kinetics were studied and analyzed. Besides, thermal stability and safety parameters(T_SADT, T_b) are 164.7 and 166.4℃ for compound 1, and 149.6 and 150.8℃ for compound 2, respectively.     

The thermal decomposition reactions of [Co(en)n(phen)m]Cl3 complexes

The thermal behaviour of [Co(en)_n(phen)_m]Cl₃ complexes has been studied using thermogravimetry (TG), differential thermogravimetry (DTG) and differential thermal analysis (DTA) in air, nitrogen and oxygen atmospheres. The effect of the stoichiometry of the complexes and that of the gas atmosphere in the furnace chamber on the thermal decomposition reaction is evidenced and discussed. The following thermal stability order has been found [Co(en)₃]Cl₃ [Co(en)₂(phen)]Cl₃ > [Co(en)(phen)₂]Cl₃ [Co(phen)₃]Cl₃     

SYNTHESIS AND SPECTRAL STUDIES OF(μ-PHENYLTHIO) (μ-ALKYLTHIO) HEXACARBONYLDIIRON COMPLEXES

Through reductive reaction between PhL1 and μ-S2 Fe (CO/6,tollowed by nucleophilicsubstitution of the intermediate (μ-PhS} (μ-LIS} Fe2 (CO)6 toward RX,nine Fe-S clus-ter complexes of (μ-PhS)(μ-RS)Fe2(CO)6 series have been synthesized.The influence of RX structures on the activities in nucleophilic substitution has been examined and possible steroisomers and isomer ratios of the complexes determined.In addition,the regular variations of isomer's CH3-S and CH2-S which are caused by the anisotropic effects of C-O and orientations of unshared electron pairs on sulfurs,have also been preliminarily discussed.     

Facile and efficient fabrication of g-C3N4 quantum dots for fluorescent analysis of trace copper(II) in environmental samples

A facile and efficient fabrication of g-C₃N₄ quantum dots with highly fluorescent based on recrystallization and ultrasonic exfoliation was presented. The obtained g-C₃N₄ QDs was successfully applied to the determination of trace Cu(II) in different environmental water samples.     

Synthesis and Fluorescence of a New Active Material for Electrochemiluminescent Sensor:Ru(phen)2[phen-NHCO(CH2)4Br](PF6)2

Recently, much attention has been paid to Ru(II) complexes because of their excellent properties of photochemistry, phtophysis. Bis(2,2'-bipyridine)[4-methyl-4'-(6-bromohexyl)-2,2'-bipyridine] ruthenium(II) perchlorate has been used as an active material for electrochemiluminescent (ECL) sensor for selective detection of oxalic acid.It is known that ECL efficiency of Ru(phen)₃²⁺ is much higher than that of Ru(bpy)₃²⁺. In order to make out more efficient ECL sensor, we have designed and synthesized a new Ru(II) complex, Ru(phen)₂[phen-NHCO(CH₂)₄Br](PF₆)₂.